You can cut degree angles with most circular saws by adjusting the degree angle (her curcular saw has a yellow almond-shaped tab handle). You can also set up a fence for a large straight edge angle cut. It is a good idea to start with a circular saw and work your way up. You'll end up using each if you really get into it. And these tools have a resell value of some sort so take good care of them and keep the original boxes and manuals. I usually collapse the box down, tuck the manual inside and store these flat in the garage. I do it for just about everything I buy, so when the time comes to sell for lack of use or upgrade, I can get a better resell dollar due to care and original packaging. BE CAREFUL, EYE PROTECTION, NO LOOSE CLOTHING, BE FOCUSED, AND GO SLOW, NO DISTRACTIONS. Great video @WelcometoTheWoods
Your video clarified the purpose of all three saws--thank you. I've owned a circular saw like what you showed for over 30 years. I don't use it much, but wouldn't be without it. This year I bought a smaller, battery powered circular saw for cutting smaller lumber up to 2x4 in size. Given that the blade on these saws spin at 3,000+ rpm and cut off more than 4,000 fingers a year, there's no tool I respect and fear more than my two circular saws. I have watched countless TH-cam safety videos on the precautions to take when using such saws, as well as the ones you demonstrated, including accounts from people who's lives were never the same after an accident with such a saw. That said, I would like to offer a humble, friendly suggestion that you consider redoing the table saw part of this video where you demonstrate its use with all the safety equipment in place and using proper handling precautions. Safety equipment includes as a minimum riving knife, anti-kickback pawls, blade guards, safety glasses, and hearing protection, while handling precautions on the table saw include push sticks that keep your fingers far from the blade, not standing directly behind the wood piece being cut, minimize distractions (put phone on vibrate before cutting), strategize how the cut will be done before doing it (i.e., risk assessment) and not allowing the wood piece as it's being cut to come in contact with the saw's fence where the wood could be pinched between the fence and the spinning blade causing a serious, split-second, kick-back injury that could be life threatening. Because your intended audience is a DIY beginner, you would be doing them a great favor to stress the fact that use of these saws, especially the table saw, come with far greater responsibility for safe use than any other non-cutting, power tool in their shop due to high risk of injury. Also, it would be good to mention that if they are working alone, they should have their cell phone charged and on their person in the event there is an accident and they have to call 911. Perhaps it would be helpful to include one or two of your favorite links to other TH-cam videos for the safe use of each of the three types of saws you demonstrated. Doing so will give the viewers a greater appreciation for how beautiful and wonderful it is to have uninjured hands, and other body parts, and to not take such things for granted when using these powerful cutting tools. Thanks for your consideration. www.motherjones.com/politics/2013/05/table-saw-sawstop-safety-finger-cut/
Save your breath. If you watch many of her other videos, you'll see many of the safety issues you point out with comments mentioning them. She still continues practicing unsafe power tool use. Hopefully she starts to take the repeated comments about safety to heart.
Thank you for saying this. I'm a total beginner with power tools. Yesterday I had my first lesson with how to use an angle grinder (🙈 don't laugh 😂) I had bought all the safety gear, and my brother who works in a very industrial industry, didn't want to put any of it on cos he's a pro (which he is) I refused to begin until he did - my logic is that it's the one time you don't wear a face guard or leather gloves etc, that something goes wrong in a permanent live changing way. I must admit I'm a little terrified of it all at the moment 🙈🙈😬
After watching tons of mitre saw videos I finally got one and the first time we tried it, it started throwing wood pieces around! I ended up returning my brand new Dewalt mitre saw but I do agree these power tools can be dangerous and DIYers on TH-cam make it look so easy. I really do think there was a specific problem with that saw and I’ll get a new one. But this time, I won’t try it without all my safety gears lol
The circular saw is a versatile tool, but to prevent kickback, avoid setting the cut depth lower than what is needed to cut the material you work with. Also, keep a sharp blade on the circular saw to get a clean cut and not have to force the saw through the material. If the motor is 15 amps, always better to use a heavier 12 gauge extension cord. Every tool can do its job, but to be safe and effective, never rush the work.
I am an avid DIY'r. In short time, you will realize you need all 3 (and then some)! The right tool (saw, in this case) for the job makes life a whole lot easier, as i am sure you know. Great channel by the way. Really enjoyed those composite front steps.
Diesel. Great comment. If someone is tight on space and budget, I recommend the circular saw and miter saw should be the first two buys (for most DYI house projects). Craft projects need all kinds of stuff, but that's another topic.
Thanks for making this video. I only own a circular saw and I was thinking of upgrading to a miter saw but I honestly have not mastered the circular saw yet. This video was the confirmation I needed to keep my money in my pocket.
Have all 3, but always use a push stick on your table saw keep hands at a safe distance. Been cutting for 40 years and still have all my fingers. Plunge, or track saws are a great addition also
If by "angle cut" with the circular saw you mean a bevel cut (like what you did with the table saw at the 8:30-8:40 mark) you can do those cuts with a circular saw. You just loosen the yellow knob on the front of the saw (you'll see the arched piece of metal with numbers on it) and adjust your plate to whatever degree bevel you need and then tighten the knob back down and make your bevel cut. If you mean miter cuts though you can make those as well. Just set your guide (like you do with a straight cut) and cut at whatever angle you'd like. :)
Thank you for the DIY education. I love your infectious smile and enthusiasm when you introduce each of the saw. It is genuine and authentic. Awesome !
Great video this helped me a buch. I was debating whether to buy a mitre or table saw as part of a deck rebuild. But you made me realize the circular saw good enough. It never occured to me to put a straight edge down as a guide for the saw. Once I started doing that it changed the value of my circular saw. Thanks!
So incredibly helpful! I was initially gifted a miter saw but exchanged it for a circular saw since I’m a beginner. Stumbled upon this video cause I’m having doubts if I made the right decision. Thanks for sharing!
A table saw is my favorite tool of all IF you have the room to have a big table saw with an extended table. Then you can cut an entire 4x8 sheet of wood or a small piece of wood both with precision.
@@prettyyoungthing1008 Ask 10 people and probably get 10 answers. Depends on budget and needs. Lowes has a really nice Delta saw and HD has a nice Ridgid one. Also others like Skil, Metabo, Dewalt are good saws.
I don't have the battery powered miter saw. I didn't know they even made one. Great idea cutting boards to fit at the store. I have that exact table saw plus a large one with cast iron extensions. I have a miter, 2 of which you can make your cut a pull it toward you to cut wider boards. I Father was a carpenter so I inherited all his tools. To many to list. Bless your heart, I love your channel. Battery powered miter saw. Hummmm !
Melissa, it makes sense to use and encourage proper stands for the table & miter saws. Much easier on the back. And wearing proper footwear & safety glasses would be advisable.
Thanks! I've had a radial arm saw in my garage for decades (which I bought from the previous home owner) but I sold it because I couldn't justify the amount of space it took up (and far more dangerous than these). I've always had a circular saw, but never owned a miter or table saw, so this video is very helpful. I had no idea there were battery powered miter saws. Mind blown. That might be perfect for the small jobs I have to do.
My favorite is absolutely the circular saw. You can replace the miter saw with the circular saw and a square. You can also replace the table saw with a circular saw with a track. Plus it's much lighter and portable.
A good replacement for your miter saw it's a radial arm saw that will allow you much longer cut and do the same purpose and makes excellent miter cuts I also recommend that beginners with a table saw to use the guard it really isn't inconvenient if you learn to use it with the guard from the beginning and as time goes on and you feel a little more comfortable the guard can be removed be sure with the table saw you also have a good push stick to push your wood through rather than running your hand along the wood in between the fence and the blade not recommended and always safety glasses very nice.
Guards get in the way, yes that is the purpose. Please reconsider a guard and a correct width riving knife. Table saws can be so dangerous, so taking extra precautions is paramount to your safety. Love your channel, very creative and enjoyable.
Although I agree the blade guard on the table saw can be a pain to leave on all the time but you should use it if possible. BUT you should ALWAYS have the splitter/riving knife on the table saw ALL of the time to prevent kickback. Nice video - thank you from the UK : )
Thank perfect beginners guide. I really like the mitre saws, but the circular saw will be much more versatile for me as a beginner. I will definitely get a mitre saw down the line as I like the whole set up with the fitted base. As for the table saw, they look a little intimidating tbh but a greatly space saving option. 😊
Miter saw is perfect for quickly being able to cross cut relatively narrow pieces like a 2x4 to correct length. Table saw is good for ripping pieces like making them narrower and also doing jig cuts. Both have their place depending on what you need but table saw can be at times more versatile in the fact that you can rip and cross cut pieces of various dimensions with it. With miter saw you can only cross cut narrower pieces but it’s quicker to cross cut with miter saw and gives you straight cutting edge. Miter saws also have capability of doing angled cuts very easily.
@@DheeraVenkatraman never worked with a sliding miter saw. But I see your point. Question I have then, is there any reason why you would have regular miter saw versus a sliding miter saw? Are there any cuts you can perform with a regular miter saw that you cannot with a sliding one?
@@Gaba-oo4qb Basically no. A sliding compound miter saw is just a compound miter saw that slides back and forth. So there are no cuts that you are missing out on. It's slightly more pricey but I'd say it is extremely worth it. In general if a cut can be done on a miter saw I would ALWAYS pick the miter saw over a circular saw or a table saw, if at the very least for safety and ease of setup. I only reach for those other tools for cuts the miter saw cannot do.
Please be careful with the table saw, don’t take any short cuts and get a micro jig or something similar for the table saw. I now have 9 1/2 fingers and 70 stitches where I thought the wood was wide enough to push my hand up to the blade, but kickback pulled the hand in
Very important if you would like to saw with precision. (avoid torsion as much as possible)! Always choose a Miter saw with a handle positioned in a vertical line above the saw blade. Everything must be aligned, slide rails, handle, and saw blade, it is much better this way the blade will not tilt. Because there is some torsion in the aluminum housing . And choose an engine with softstart on it to prevent wear of the gear and worm shaft. It is very important that everything is aligned. Here are some examples to show how the handle must be positioned above the blade. Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / / HITACHI C12RSH2 / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact . (This also is the case with the Miter saw without the slide rails). If you want you can test it yourself at home if there is torsion in the aluminum housing. Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood. To this with the normal handle positioned on the right side of the Miter saw. Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blade is cased in. Just now only do this without the running engine. Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut.If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing. Step-4. therefor it is much better to choose a Miter saw with the handle positioned vertical in line above the saw blade.
I was skepticle of a 20 volt circular saw. But I have several B&D 20 volt batteries and the drill Works great th-cam.com/users/postUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c . I saw the 4 stars and some glowing reviews so decided to purchase this saw. Well, leave your money in your pocket and run a cord because this little saw won't cut
I have all 3. I don't use a circular too much, as you get more error when cutting free hand. I build beehive equipment with them mainly. I use the table saw to rip the long boards down to width, then use the miter saw to cut to length. I am planning on cutting down a granite sink top for my bathroom project, which will probably involve the circular saw for that. I need to take 2" off each end to keep the sink and faucet centered. I will then use the table saw and compound miter saw to build a new cabinet and doors for the sink top.
Love your videos, such good information and detailed instructions!! Have you ever tried building a table with the circular saw mounted underneath it for you're own DIY Table Saw? I've seen it done but never tried it myself. Thanks again.
Nicely broken down! I have made a bunch of things just with a circular saw as I don't own any other saw except a jig saw which I hardly ever use. It's possible to use the circular saw but every little cut other than a cross or miter cut can be a creative problem solving exercise. It takes time and sometimes the cuts aren't precise but most of the time, I have been please with how neat the joinery looks. I have even ripped boards to the right width and thickness for my projects. With that being said, I am struggling with cutting neat rabets and grooves for some reason. Leaning towards going for a table saw only. Good to know it can make miter cuts too. Why do we need a miter saw of the table saw does the same?
I bought a circular saw as a beginner in wood working. A table saw is still very expensive for me and also higher energy consumption. Thanks for this video, so I know what to buy next 🙏
@@baxterenrife are you dense? is that your poor attempt at a joke? With your intellect would anyone actually be surprised if you cut off your other index finger?
Thanks a lot for your video. Helping a beginner like me. I have been asking for help and got lots of different answers to exactly this question, now I know that what I thought was similar to your idea. Will get a circular saw with the possibility to tilting. Looking forward for more videos. Thanks
I stumbled on this video. I've really been trying to decide which one to get (table saw is out if my range at the mo) but even though I know (now) the circular saw seems to be the most logical, that's the one that scares me for some reason 😬😳🙈 ... thanks for explaining the difference, similarities, pros and cons. Very useful video.
Excellent video all the saws are useful in their own way another useful addition would be a bandsaw I have just bought one and it is now my go to saw for most jobs. Really like your videos.
Without a doubt. Especially if you are working from narrower pre-sawed wooden planks and mostly just need to cut them to length rapidly. A sliding mitre saw will give you additional options for slightly wider wood too. They are even great for cutting angled or box steel with the right blade attached.
I have been doing DYI work for the last 5 years. I have collected dozens of tools from Milwaukee, starting from drills. Saws were among the last that I got because they are the most dangerous and I got two young boys. I remember damaging (and almost hurting myself) my $500 milwaukee fuel mitre saw the first time I used it. I had to read the instructions twice when I replaced it. They arent a joke. I still dont have a table saw...
Personally I find miter saws MUCH faster to setup than a circular saw. With a circular saw, if you want to cross cut a long piece safely at the middle you need to set up 4 sawhorses or some sacrificial material. If you want to cut straight you need to clamp some fence to the piece. With a miter saw you need none of that crap. If your cuts aren't longer than 60cm (can be done in two 30cm cuts) I'd just stick to a miter saw. It's also worth mentioning that the miter saw is BY FAR the safest of the 3 saws by far and it should probably the be the first power saw a beginner should buy. By the way, your use of the table saw is extremely unsafe. Also comments on 6:20: - Reduce your blade height to just barely clear your piece by a little bit. Your blade is too high. - Get a riving knife which reduces kickback - NEVER stand directly behind your piece, let alone squatting. A kickback can literally kill you. Mount that tablesaw at a reasonable height, stand to one side of the piece, use a push stick. Watch some safety videos.
Just getting into working and have been doing a lot of research. The only saw I own is a hand saw and plan on purchasing my first circular saw in the upcoming weeks.
Thank you for the video. I have been trying to determine what to buy between the miter saw and table saw. Reason being that I want to be able to cut rabbet joint but also be able to cut angles. The only missing information is whether or not the table saw can be set up with a rabbet joint "blade".
Great Video clip! Sorry for butting in, I would appreciate your initial thoughts. Have you considered - Schallingora Dexterous Programme Scheme (erm, check it on google should be there)? It is a smashing one of a kind guide for building any shed in no time with no experience without the normal expense. Ive heard some unbelievable things about it and my friend after many years got astronomical results with it.
How would you make a long cut on a narrow board such as a 2.5" or 3" wide baseboard? The tiler took out only part of the baseboard in the utility room. Now I need to match the baseboard on the other wall with tile up to it. I need to cut a long narrow cut along the baseboard he took out where the tile goes up to the wall. I'm thinking circular saw and clamp down the long baseboard and carefully cut the long narrow cut with a circular saw. I don't own a table saw.
I have to agree with some of the people who posted about some safety information and implementation from you in your videos. I have been a woodworker most of my working life and safety has always been a part of my work environment. As much as I appreciate your cute legs; your working in sandals and bare foot a lot of times is downright dangerous and could lead to a serious situation. Another thing that I find interesting is how you almost always work on the ground or garage floor when cutting with your tools. Another thing that can be and lead to a lack of control. As an older person; I worry about your back if you continue to work that way as long as I have done. Have you tried to put your tools on saw horses or on your great work winch you made in a video? I am not sure I have ever seen you use ear protection or a dust mask. I enjoy your videos and your design mind but as a foreman in big shops including in Antarctica; I have been in charge of osha run shops where safety measures are insisted on. I feel that some of the DYI people that watch you could benefit from some info and modeling of such subject matter. You may disagree; you make your own choices but I have seen too many injuries as a result of lack of safety measures.
As a master carpenter myself….I couldn’t agree with you more. The video has good intention but is boarder line good information for inexperienced people looking for some advice.
Question. I have a chop saw and now recently a table saw. is the chop saw a bit redundant now? Keen to save space where possible but also don’t want to lose a tool I’ll later need to use.
This test is only if you want to saw with a precision miter saw. (not for rough work). Tips and Test: Very important if you would like to saw with precision. (avoid torsion as much as possible)! Always choose a Miter saw with a handle positioned in a vertical line above the saw blade. Everything must be aligned, slide rails, handle, and saw blade,it is much better this way the blade will not tilt. Because there is some torsion in the aluminum housing . And choose an engine with softstart on it to prevent wear of the gear and worm shaft. It is very important that everything is aligned. Here are some examples to show how the handle must be positioned above the blade. Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / Bosch GCM 8 SDE / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact / Bosch PCM 8 SD / Hitachi C10FSH. (This also is the case with the Miter saw without the slide rails). (If you want). You can test it yourself at home if there is torsion in the aluminum housing. Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood about +- 20 mm thick to this with the normal handle positioned on the right side of the Miter saw (the wood it will remain in place until the test is completed). Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blade is cased in. Just now only do this without the running engine. Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut. If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing (test is completed). Step-4. therefor it is much better to choose a Miter saw with the handle positioned vertical in line above the saw blade. Conclusion: how further away the handle is from the saw blade how more chance of torsion in the aluminum housing.(don't go for that). Also with a cheap slide miter saw it is still better the handgriff in line a above the saw blade than on the right side. Maybe they will make it someday then we have a winner...
Glad you are explaining basic tools pros/cons. Have you done a video I don't see yet on planers? I thought I was going to seek a DeWalt, but today I was at a woodworking store that sells Jet 13" Helical Style Bench Top; seems the stainless steel vs aluminum could be an a perk? My project is to make a 10'x4'x3" kitchen island butcher block to place on island base already in place. They thought I would regret running 10' boards through that planer size though....thoughts? Thanks.
I think this video is great but I would encourage you to add more footage about the table saw and the safety guidelines that are to be observe for a safe operation, the reason I ask you this is because anyone that buys a table saw must be made aware of the responsibility that comes with it, since it provides the least of safety guards as it is meant for people to use it to be fully aware of what the are doing (i.e. like never position yourself directly in front of the saw, or the best way to push the material to cut, etc...) the circular saw and or miter saw somehow represents a much more controlled and safety environment due to their own design, and while they also need to be handled adequately they are less dangerous compared to the table saw.
The way to look at it is they each do their own different jobs. But, I agree that if you're just starting DIY and need something to do a few cuts a circular saw is better. They're more portable, and being smaller they're easier to store without needing a whole workshop. Fundamentally, a circular saw is a hand tool, you take it to the work, which the compound miter and the table saws are stationary tools, you take the work to them. If you have a lot of cuts, and a bunch of projects to do, then it would be good to get a compound miter and a table saw.
@@ColorLifeLaugh Honestly I would consult Lowes or Home Depot for that. Get whatever is more standard for size and brands like DeWalt, Makita should be good.
Very good and informative video. I own a circular and miter saw and would love to have a table saw but I do not have room in my garage. But, the one you have is like a table model which I could store and use. I just may look into getting one of those and your DeWalt model looks like a good one. Thanks for the lesson on saw types.
You can cut degree angles with most circular saws by adjusting the degree angle (her curcular saw has a yellow almond-shaped tab handle). You can also set up a fence for a large straight edge angle cut. It is a good idea to start with a circular saw and work your way up. You'll end up using each if you really get into it. And these tools have a resell value of some sort so take good care of them and keep the original boxes and manuals. I usually collapse the box down, tuck the manual inside and store these flat in the garage. I do it for just about everything I buy, so when the time comes to sell for lack of use or upgrade, I can get a better resell dollar due to care and original packaging. BE CAREFUL, EYE PROTECTION, NO LOOSE CLOTHING, BE FOCUSED, AND GO SLOW, NO DISTRACTIONS. Great video @WelcometoTheWoods
Your video clarified the purpose of all three saws--thank you. I've owned a circular saw like what you showed for over 30 years. I don't use it much, but wouldn't be without it. This year I bought a smaller, battery powered circular saw for cutting smaller lumber up to 2x4 in size. Given that the blade on these saws spin at 3,000+ rpm and cut off more than 4,000 fingers a year, there's no tool I respect and fear more than my two circular saws. I have watched countless TH-cam safety videos on the precautions to take when using such saws, as well as the ones you demonstrated, including accounts from people who's lives were never the same after an accident with such a saw. That said, I would like to offer a humble, friendly suggestion that you consider redoing the table saw part of this video where you demonstrate its use with all the safety equipment in place and using proper handling precautions. Safety equipment includes as a minimum riving knife, anti-kickback pawls, blade guards, safety glasses, and hearing protection, while handling precautions on the table saw include push sticks that keep your fingers far from the blade, not standing directly behind the wood piece being cut, minimize distractions (put phone on vibrate before cutting), strategize how the cut will be done before doing it (i.e., risk assessment) and not allowing the wood piece as it's being cut to come in contact with the saw's fence where the wood could be pinched between the fence and the spinning blade causing a serious, split-second, kick-back injury that could be life threatening. Because your intended audience is a DIY beginner, you would be doing them a great favor to stress the fact that use of these saws, especially the table saw, come with far greater responsibility for safe use than any other non-cutting, power tool in their shop due to high risk of injury. Also, it would be good to mention that if they are working alone, they should have their cell phone charged and on their person in the event there is an accident and they have to call 911. Perhaps it would be helpful to include one or two of your favorite links to other TH-cam videos for the safe use of each of the three types of saws you demonstrated. Doing so will give the viewers a greater appreciation for how beautiful and wonderful it is to have uninjured hands, and other body parts, and to not take such things for granted when using these powerful cutting tools. Thanks for your consideration. www.motherjones.com/politics/2013/05/table-saw-sawstop-safety-finger-cut/
Save your breath. If you watch many of her other videos, you'll see many of the safety issues you point out with comments mentioning them. She still continues practicing unsafe power tool use. Hopefully she starts to take the repeated comments about safety to heart.
Thanks for taking the time to address this issue. No joking. These power tools are powerful!
@@M_M0109 exactly. this woman is ruthless and a tyical 'that' type of americans...
Thank you for saying this. I'm a total beginner with power tools. Yesterday I had my first lesson with how to use an angle grinder (🙈 don't laugh 😂) I had bought all the safety gear, and my brother who works in a very industrial industry, didn't want to put any of it on cos he's a pro (which he is) I refused to begin until he did - my logic is that it's the one time you don't wear a face guard or leather gloves etc, that something goes wrong in a permanent live changing way. I must admit I'm a little terrified of it all at the moment 🙈🙈😬
After watching tons of mitre saw videos I finally got one and the first time we tried it, it started throwing wood pieces around! I ended up returning my brand new Dewalt mitre saw but I do agree these power tools can be dangerous and DIYers on TH-cam make it look so easy. I really do think there was a specific problem with that saw and I’ll get a new one. But this time, I won’t try it without all my safety gears lol
Your circular saw can cut angles. The front yellow leveler controls the degree. Thanks for the video. Very Informative! 😀
yeah but dont do that for finishing work lmao
The circular saw is a versatile tool, but to prevent kickback, avoid setting the cut depth lower than what is needed to cut the material you work with. Also, keep a sharp blade on the circular saw to get a clean cut and not have to force the saw through the material. If the motor is 15 amps, always better to use a heavier 12 gauge extension cord. Every tool can do its job, but to be safe and effective, never rush the work.
I am an avid DIY'r. In short time, you will realize you need all 3 (and then some)! The right tool (saw, in this case) for the job makes life a whole lot easier, as i am sure you know. Great channel by the way. Really enjoyed those composite front steps.
Diesel. Great comment. If someone is tight on space and budget, I recommend the circular saw and miter saw should be the first two buys (for most DYI house projects). Craft projects need all kinds of stuff, but that's another topic.
Thanks for making this video. I only own a circular saw and I was thinking of upgrading to a miter saw but I honestly have not mastered the circular saw yet. This video was the confirmation I needed to keep my money in my pocket.
I own all three but the table saw is the most useful and versatile followed by the circular saw. They all have there special place. Great job.
Have all 3, but always use a push stick on your table saw keep hands at a safe distance. Been cutting for 40 years and still have all my fingers.
Plunge, or track saws are a great addition also
Would you prefer a table saw or miter saw?
If by "angle cut" with the circular saw you mean a bevel cut (like what you did with the table saw at the 8:30-8:40 mark) you can do those cuts with a circular saw. You just loosen the yellow knob on the front of the saw (you'll see the arched piece of metal with numbers on it) and adjust your plate to whatever degree bevel you need and then tighten the knob back down and make your bevel cut. If you mean miter cuts though you can make those as well. Just set your guide (like you do with a straight cut) and cut at whatever angle you'd like. :)
Yes a circular saw is very versatile!
@@WelcometotheWoodsBlog "thank you for pointing that out Jared, I didn't know at the time of the video but thanks to commenters I do now"
Thank you for the DIY education. I love your infectious smile and enthusiasm when you introduce each of the saw. It is genuine and authentic. Awesome !
I like your blog, because I identify with you because I like the same things as you. You're a brave woman. You have my admiration and sympathy.
Great video this helped me a buch. I was debating whether to buy a mitre or table saw as part of a deck rebuild. But you made me realize the circular saw good enough. It never occured to me to put a straight edge down as a guide for the saw. Once I started doing that it changed the value of my circular saw. Thanks!
So incredibly helpful! I was initially gifted a miter saw but exchanged it for a circular saw since I’m a beginner. Stumbled upon this video cause I’m having doubts if I made the right decision. Thanks for sharing!
Love the BATTERY POWERED miter saw. Handy
A table saw is my favorite tool of all IF you have the room to have a big table saw with an extended table. Then you can cut an entire 4x8 sheet of wood or a small piece of wood both with precision.
Which table should I get? I’m trying to buy one for my dad .
@@prettyyoungthing1008 Ask 10 people and probably get 10 answers. Depends on budget and needs. Lowes has a really nice Delta saw and HD has a nice Ridgid one. Also others like Skil, Metabo, Dewalt are good saws.
Hi Melissa,
I agree with you I will go with the circular saw as the first saw you will need.
Thanks for sharing!
I think you would need all three at the same time
you need a 3 what do you mean
Good job explaining all these, I have never used a table saw or Miter saw. I mostly use circular saw or jigsaw or Hacksall. Measure twice cut once.❤
I don't have the battery powered miter saw. I didn't know they even made one. Great idea cutting boards to fit at the store. I have that exact table saw plus a large one with cast iron extensions. I have a miter, 2 of which you can make your cut a pull it toward you to cut wider boards. I Father was a carpenter so I inherited all his tools. To many to list. Bless your heart, I love your channel. Battery powered miter saw. Hummmm !
Circular saw is definitely the best. I have all three but I use the circular saw the most. Not the most accurate but definitely the best
I agree, it's not the most accurate, but it's the most versatile!
Very education for us first time DIYers. Thank you so much!
Melissa, it makes sense to use and encourage proper stands for the table & miter saws. Much easier on the back. And wearing proper footwear & safety glasses would be advisable.
An accident happens once but the regret remains the whole life. Please consider safety measures more seriously. ^Thanks for the video
Thanks! I've had a radial arm saw in my garage for decades (which I bought from the previous home owner) but I sold it because I couldn't justify the amount of space it took up (and far more dangerous than these). I've always had a circular saw, but never owned a miter or table saw, so this video is very helpful. I had no idea there were battery powered miter saws. Mind blown. That might be perfect for the small jobs I have to do.
My favorite is absolutely the circular saw. You can replace the miter saw with the circular saw and a square. You can also replace the table saw with a circular saw with a track. Plus it's much lighter and portable.
I didn't know they make square saw blade!
@@WarPigstheHun Square is not a saw blade. It's a measuring tool.
@@thegoldenland I will let you know how my stacked Dado Carbide tipped Square blades work!
A good replacement for your miter saw it's a radial arm saw that will allow you much longer cut and do the same purpose and makes excellent miter cuts I also recommend that beginners with a table saw to use the guard it really isn't inconvenient if you learn to use it with the guard from the beginning and as time goes on and you feel a little more comfortable the guard can be removed be sure with the table saw you also have a good push stick to push your wood through rather than running your hand along the wood in between the fence and the blade not recommended and always safety glasses very nice.
open toed shoes not suggested 0:56
Guards get in the way, yes that is the purpose. Please reconsider a guard and a correct width riving knife. Table saws can be so dangerous, so taking extra precautions is paramount to your safety. Love your channel, very creative and enjoyable.
Thanks lady. I didn't expect this video to solve my dilemma ❤
Although I agree the blade guard on the table saw can be a pain to leave on all the time but you should use it if possible.
BUT you should ALWAYS have the splitter/riving knife on the table saw ALL of the time to prevent kickback.
Nice video - thank you from the UK : )
Thank you for this video. It was a big help as I decide on my first saw!😊
Thank perfect beginners guide. I really like the mitre saws, but the circular saw will be much more versatile for me as a beginner. I will definitely get a mitre saw down the line as I like the whole set up with the fitted base. As for the table saw, they look a little intimidating tbh but a greatly space saving option. 😊
Had the miter saw but took it back and got a nice Dewalt circular saw and jigsaw to start with.. Table saw next and then the miter saw😎
Miter saw is perfect for quickly being able to cross cut relatively narrow pieces like a 2x4 to correct length. Table saw is good for ripping pieces like making them narrower and also doing jig cuts. Both have their place depending on what you need but table saw can be at times more versatile in the fact that you can rip and cross cut pieces of various dimensions with it. With miter saw you can only cross cut narrower pieces but it’s quicker to cross cut with miter saw and gives you straight cutting edge. Miter saws also have capability of doing angled cuts very easily.
A sliding miter saw can cut upto 12 inches in width, or 24 inches in 2 cuts. A good miter saw is much more versatile than most people think it to be.
@@DheeraVenkatraman never worked with a sliding miter saw. But I see your point. Question I have then, is there any reason why you would have regular miter saw versus a sliding miter saw? Are there any cuts you can perform with a regular miter saw that you cannot with a sliding one?
@@Gaba-oo4qb Basically no. A sliding compound miter saw is just a compound miter saw that slides back and forth. So there are no cuts that you are missing out on. It's slightly more pricey but I'd say it is extremely worth it. In general if a cut can be done on a miter saw I would ALWAYS pick the miter saw over a circular saw or a table saw, if at the very least for safety and ease of setup. I only reach for those other tools for cuts the miter saw cannot do.
My husband is lazy and so I'm going to learn how to put trim up and other small things by watching TH-cam videos. 👍👍👍
Please be careful with the table saw, don’t take any short cuts and get a micro jig or something similar for the table saw. I now have 9 1/2 fingers and 70 stitches where I thought the wood was wide enough to push my hand up to the blade, but kickback pulled the hand in
Wow !!!
👍✊
Nice bro!
Ooof.. thanks for the warning. Hope you are ok
😔💔 hope you're doing okay
Sorry to hear but thanks for sharing.
I wonder, did you have a splitter or a riving knife installed?
Very important if you would like to saw with precision. (avoid torsion as much as possible)!
Always choose a Miter saw with a handle positioned in a vertical line above the saw blade.
Everything must be aligned, slide rails, handle, and saw blade, it is much better this way the blade will not tilt.
Because there is some torsion in the aluminum housing .
And choose an engine with softstart on it to prevent wear of the gear and worm shaft.
It is very important that everything is aligned.
Here are some examples to show how the handle must be positioned above the blade.
Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / / HITACHI C12RSH2 / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact .
(This also is the case with the Miter saw without the slide rails).
If you want you can test it yourself at home if there is torsion in the aluminum housing.
Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood. To this with the normal handle positioned on the right side of the Miter saw.
Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blade is cased in. Just now only do this without the running engine.
Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut.If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing.
Step-4. therefor it is much better to choose a Miter saw with the handle positioned vertical in line above the saw blade.
This is so helpful! Thank you for sharing!! Just getting started in DIY home projects!
Wait. The Circular saw can do some bevel cuts as well and you can change depth of blade.
Agreed! I was about to post the same.
Yes I do that all the time with my circular saw
I was skepticle of a 20 volt circular saw. But I have several B&D 20 volt batteries and the drill Works great th-cam.com/users/postUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c . I saw the 4 stars and some glowing reviews so decided to purchase this saw. Well, leave your money in your pocket and run a cord because this little saw won't cut
I’m a newbie. You’re saying a 20V circular saw is no good? It doesn’t produce enough power?
I'm a beginner on trying to do DIY tables. I love the way you explained, i like miter saw, Thank you for explaining it well
I have all 3. I don't use a circular too much, as you get more error when cutting free hand. I build beehive equipment with them mainly. I use the table saw to rip the long boards down to width, then use the miter saw to cut to length. I am planning on cutting down a granite sink top for my bathroom project, which will probably involve the circular saw for that. I need to take 2" off each end to keep the sink and faucet centered. I will then use the table saw and compound miter saw to build a new cabinet and doors for the sink top.
The only thing missing is safety glasses, earplugs, shoes and saw guards. 🙂
At 2:22, that yellow T-handle on the front of your circular saw is for miter cuts. Loosen it and then tilt the plate relative to the blade ;)
Love your videos, such good information and detailed instructions!! Have you ever tried building a table with the circular saw mounted underneath it for you're own DIY Table Saw? I've seen it done but never tried it myself. Thanks again.
Good video. Informative yet simple, great for a beginner like me
Nicely broken down! I have made a bunch of things just with a circular saw as I don't own any other saw except a jig saw which I hardly ever use. It's possible to use the circular saw but every little cut other than a cross or miter cut can be a creative problem solving exercise. It takes time and sometimes the cuts aren't precise but most of the time, I have been please with how neat the joinery looks. I have even ripped boards to the right width and thickness for my projects. With that being said, I am struggling with cutting neat rabets and grooves for some reason. Leaning towards going for a table saw only. Good to know it can make miter cuts too.
Why do we need a miter saw of the table saw does the same?
Your explanation is simple and undestandale . thanks
I bought a circular saw as a beginner in wood working. A table saw is still very expensive for me and also higher energy consumption. Thanks for this video, so I know what to buy next 🙏
Yes I think a miter saw would be a great addition to your tool collection and improve your cut accuracy/efficiency!
Excellent video- clear and to the point.
I'm a carpenter with 30 years of experience. Six years ago I chopped off my left index finger with a circular saw. Please be very cautious.
Ouch!
Can happen to anyone.. sorry for your loss
@@Karll541 Precisely what I said at the time. Where you there per chance?
@@baxterenrife are you dense? is that your poor attempt at a joke? With your intellect would anyone actually be surprised if you cut off your other index finger?
@@Karll541 I've no idea whether or not they would. But I seem to have offended you. How is that?
Thanks a lot for your video. Helping a beginner like me. I have been asking for help and got lots of different answers to exactly this question, now I know that what I thought was similar to your idea. Will get a circular saw with the possibility to tilting. Looking forward for more videos. Thanks
An informative and well paced video. Thanks :)
I think a high quality large sliding compound miter saw combined with a circular saw is a hard combo to beat.
Thank god I clicked u your getting to the point fast no lagging I love it!
Thank you for this easy straight to the point explanation for total beginners❤❤
Thank you, I will be starting with the circular saw.
I stumbled on this video. I've really been trying to decide which one to get (table saw is out if my range at the mo) but even though I know (now) the circular saw seems to be the most logical, that's the one that scares me for some reason 😬😳🙈 ... thanks for explaining the difference, similarities, pros and cons. Very useful video.
Excellent video all the saws are useful in their own way another useful addition would be a bandsaw I have just bought one and it is now my go to saw for most jobs. Really like your videos.
For somebody who's interested in just building planter boxes would you say that the Miter Saw would be the most appropriate and safest?
I'd recommend the miter saw as it would be the fastest, safest, and most convenient.
Without a doubt. Especially if you are working from narrower pre-sawed wooden planks and mostly just need to cut them to length rapidly. A sliding mitre saw will give you additional options for slightly wider wood too. They are even great for cutting angled or box steel with the right blade attached.
I have been doing DYI work for the last 5 years. I have collected dozens of tools from Milwaukee, starting from drills. Saws were among the last that I got because they are the most dangerous and I got two young boys. I remember damaging (and almost hurting myself) my $500 milwaukee fuel mitre saw the first time I used it. I had to read the instructions twice when I replaced it. They arent a joke. I still dont have a table saw...
Personally I find miter saws MUCH faster to setup than a circular saw. With a circular saw, if you want to cross cut a long piece safely at the middle you need to set up 4 sawhorses or some sacrificial material. If you want to cut straight you need to clamp some fence to the piece. With a miter saw you need none of that crap. If your cuts aren't longer than 60cm (can be done in two 30cm cuts) I'd just stick to a miter saw.
It's also worth mentioning that the miter saw is BY FAR the safest of the 3 saws by far and it should probably the be the first power saw a beginner should buy.
By the way, your use of the table saw is extremely unsafe. Also comments on 6:20:
- Reduce your blade height to just barely clear your piece by a little bit. Your blade is too high.
- Get a riving knife which reduces kickback
- NEVER stand directly behind your piece, let alone squatting. A kickback can literally kill you. Mount that tablesaw at a reasonable height, stand to one side of the piece, use a push stick. Watch some safety videos.
What a great video! Thanks for sharing
Thank you, it truly helped me decide on my first saw♥️♥️♥️♥️
Until now I had no idea that ladies are into these things as well!
Your video was helpful!
Thank you and you're beautiful!
Very informative video. What would you recommend would be the best for shelving?
tablesaw
Mouse at 8:26? Useful summary thanks
Just getting into working and have been doing a lot of research. The only saw I own is a hand saw and plan on purchasing my first circular saw in the upcoming weeks.
Don't buy the cheapest one you see...stay out of Harbor Freight!
I have all three and use all for various applications Good info thanks
Thank you for the video. I have been trying to determine what to buy between the miter saw and table saw. Reason being that I want to be able to cut rabbet joint but also be able to cut angles. The only missing information is whether or not the table saw can be set up with a rabbet joint "blade".
Looks like I’m going with a table saw. Already have a circular saw. Thanks
Great Video clip! Sorry for butting in, I would appreciate your initial thoughts. Have you considered - Schallingora Dexterous Programme Scheme (erm, check it on google should be there)? It is a smashing one of a kind guide for building any shed in no time with no experience without the normal expense. Ive heard some unbelievable things about it and my friend after many years got astronomical results with it.
@@maliehakusain2188 no! leave me alone now
Exactly the info I was looking for - thank you!
Awesome! So glad this video was helpful for you!
How would you make a long cut on a narrow board such as a 2.5" or 3" wide baseboard? The tiler took out only part of the baseboard in the utility room. Now I need to match the baseboard on the other wall with tile up to it. I need to cut a long narrow cut along the baseboard he took out where the tile goes up to the wall. I'm thinking circular saw and clamp down the long baseboard and carefully cut the long narrow cut with a circular saw. I don't own a table saw.
I have to agree with some of the people who posted about some safety information and implementation from you in your videos. I have been a woodworker most of my working life and safety has always been a part of my work environment. As much as I appreciate your cute legs; your working in sandals and bare foot a lot of times is downright dangerous and could lead to a serious situation. Another thing that I find interesting is how you almost always work on the ground or garage floor when cutting with your tools. Another thing that can be and lead to a lack of control. As an older person; I worry about your back if you continue to work that way as long as I have done. Have you tried to put your tools on saw horses or on your great work winch you made in a video? I am not sure I have ever seen you use ear protection or a dust mask. I enjoy your videos and your design mind but as a foreman in big shops including in Antarctica; I have been in charge of osha run shops where safety measures are insisted on. I feel that some of the DYI people that watch you could benefit from some info and modeling of such subject matter. You may disagree; you make your own choices but I have seen too many injuries as a result of lack of safety measures.
As a master carpenter myself….I couldn’t agree with you more.
The video has good intention but is boarder line good information for inexperienced people looking for some advice.
👍🏻👍🏻👍🏻
She gotta show dem legs for da thirsty men!
You’re right, she’s absolutely beautiful would be horrible if something happened
Very well done ! Very helpful and exactly what I was looking for. Thank You !
Circular saw: Flexibility and support tools needed
Miter: Wood edges and angles
Table saw: Stability and precision
Liked and Subscribed cause I never knew a model could do woodwork..
Question. I have a chop saw and now recently a table saw. is the chop saw a bit redundant now? Keen to save space where possible but also don’t want to lose a tool I’ll later need to use.
Are you sure it's chop saw and not a miter? Chop saw can cut metal and concrete.
Very useful video. Thank you!
Very helpful and informative.
If I ever got this tool i will go for circular saw.. i have seen many many videos converting circular saw to a table saw setup
Thank you Very useful indeed.
Very good beginners woodworking tutorial! 😃
Good job. I was able to make one automatic that works on 12 volts
Truly helpful, thank you❤
This test is only if you want to saw with a precision miter saw. (not for rough work).
Tips and Test:
Very important if you would like to saw with precision. (avoid torsion as much as possible)!
Always choose a Miter saw with a handle positioned in a vertical line above the saw blade.
Everything must be aligned, slide rails, handle, and saw blade,it is much better this way the blade will not tilt.
Because there is some torsion in the aluminum housing .
And choose an engine with softstart on it to prevent wear of the gear and worm shaft.
It is very important that everything is aligned.
Here are some examples to show how the handle must be positioned above the blade.
Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / Bosch GCM 8 SDE / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact / Bosch PCM 8 SD / Hitachi C10FSH.
(This also is the case with the Miter saw without the slide rails).
(If you want). You can test it yourself at home if there is torsion in the aluminum housing.
Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood about +- 20 mm thick to this with the normal handle positioned on the right side of the Miter saw (the wood it will remain in place until the test is completed).
Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blade is cased in. Just now only do this without the running engine.
Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut. If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing (test is completed).
Step-4. therefor it is much better to choose a Miter saw with the handle positioned vertical in line above the saw blade.
Conclusion: how further away the handle is from the saw blade how more chance of torsion in the aluminum housing.(don't go for that).
Also with a cheap slide miter saw it is still better the handgriff in line a above the saw blade than on the right side. Maybe they will make it someday then we have a winner...
Glad you are explaining basic tools pros/cons. Have you done a video I don't see yet on planers? I thought I was going to seek a DeWalt, but today I was at a woodworking store that sells Jet 13" Helical Style Bench Top; seems the stainless steel vs aluminum could be an a perk? My project is to make a 10'x4'x3" kitchen island butcher block to place on island base already in place. They thought I would regret running 10' boards through that planer size though....thoughts? Thanks.
Very informative. Thanks.
I'm going to be building a small home, and was wondering if I needed a miter saw or just use my circular saw?
I think this video is great but I would encourage you to add more footage about the table saw and the safety guidelines that are to be observe for a safe operation, the reason I ask you this is because anyone that buys a table saw must be made aware of the responsibility that comes with it, since it provides the least of safety guards as it is meant for people to use it to be fully aware of what the are doing (i.e. like never position yourself directly in front of the saw, or the best way to push the material to cut, etc...) the circular saw and or miter saw somehow represents a much more controlled and safety environment due to their own design, and while they also need to be handled adequately they are less dangerous compared to the table saw.
Great video ! You need to build a stand on wheels for your table saw.....thanks for sharing
So great, thanks 👍
Thank you so much for the video!
The way to look at it is they each do their own different jobs. But, I agree that if you're just starting DIY and need something to do a few cuts a circular saw is better. They're more portable, and being smaller they're easier to store without needing a whole workshop. Fundamentally, a circular saw is a hand tool, you take it to the work, which the compound miter and the table saws are stationary tools, you take the work to them. If you have a lot of cuts, and a bunch of projects to do, then it would be good to get a compound miter and a table saw.
Should I get a circular saw or mitre box? The saw would be better to also make straight cuts.
I’m going to be getting a saw. I am a beginner so this is helpful. I’m a bit concerned about less precise cuts. How can that be avoided?
Love your vids keep it up!
I'm terrible in terms of cutting wood straight with my circular saw, think either of the other options is pry what I need.
Hi, i just started getting interested in dyi with carpentry I never used the saw before! Should i start with a circular saw?
yes
@@meisterbear5275 should i get 6 1/4 or 7 1/4 any good brand you could recommend?
@@ColorLifeLaugh Honestly I would consult Lowes or Home Depot for that. Get whatever is more standard for size and brands like DeWalt, Makita should be good.
@@meisterbear5275 ty ill look into it so 6 1/2 is good?
Good review, ultimately is really based on your budget and versatility.
And available space.
Very good and informative video. I own a circular and miter saw and would love to have a table saw but I do not have room in my garage. But, the one you have is like a table model which I could store and use. I just may look into getting one of those and your DeWalt model looks like a good one. Thanks for the lesson on saw types.