Why doesnt this work when you connect it to a buck converter? I have a 5v dc stepper motor and am using a buck converter to output 5v dc. Whenever I connect it to this board and press the button to turn the motor on, the D2 led blinks and doesnt turn the motor on.
Hello, can I connect this 36820 module motor output pins A1,A2,B1,B2 respectively to the IN1,IN2,IN3,IN4 inputs of L298N driver module to driver a higher current stepper motor?
I’ll appreciate it if you would view 7:25 on this one year old YT video and confirm if I understand the potential of using this layout to remotely tune my antenna. As I understood, having adjusted the potentiometer for smallest ‘degree-steps’ and having placed jumpers properly, I can momentarily press one button, to ‘step’ the motor a degree at a time in one direction. If I understood what I viewed correctly so far, then can this more-accurate stepper motor movement be controlled through a two conductor cable in some way using your setup as I referred to ? (Though I can use the analog approach of PWM a DC motor with a two conductor cable controlled by DPDT wafer switch, I wouldn’t have the more desirable accuracy of rotation by degree steps)
hi im trying to find out ine thing.... so im using this on a generator carburetor. does the mode facilitate automatic stop after a complete motion. example.. if i have it set to 180 degrees turn i want it to top this may simulate the choke being fully closed and then i have my relay once the generator has started then the choke will return to the closed position going 180 degree the opposite direction i dont want the constant power oncthe motor once the position has changed
Hey - I have built a camera slider, but the control board doesnt have these cool options. Can I use a 2 wire stepper motor with this board? Does the kit come with the motor wire harness, and which color wires to use? For the limit switch, and I use a basic momentary push button switch? Also, is that wire harness included? thanks!
Hi.how we can control step motor like swing motor on air condition unit that with pressing the button it goes up and down and when press the button to off it goes to first position (down position)automatically?
hello, ive got that contral board but im faceing a problem. Im using it in that mode where it turns on or another way by pressing the switches,.. but by not pressing the switch the stepper does not hold position. Can u help me out solving this problem ?
How many Amps does the controller provide to the stepper motor? Also, are there heftier products to upscale and run a high torquing stepper motor or how might you go about that?
how to control steps movements, like lets say we have 400 circular points to move one by one and i need to move pointer in following example sequence starting from 0->10->240->45->28-> .......... -> 400 . How can we automate this ..
Fantastic video on the functions of the board. One question, yes, its been 3 years but maybe you can recall. Is there a way to make it start up in running mode. Forexample if the jumper was set to JOG mode and the run switch was bypassed to ON. Would it start running when power is supplied?
I tried two stepper motors and two controllers and the motor won't turn. The lights obey the speed control know, but no movement from the motor. Any ideas?
Thank you for sharing and very detailed info video, does the rotary knob will control the speed of the stepper motor to slow the rotation down while in stepper mode?
Thanks for this video, I have been looking for months for an alternative to arduino, for my grandson’s ramp lift (toy car), with the function start/stop, cw, ccw. Over time I invested in several control but without success.
N is this right if using a radio controlled esc would it b possable to draw the 80 or 150 amps from it so u wont need so much extra power wen using like say a blender that runs on batteries n a solar controller or pmw
hello, can I programmate it for use buttons for one step for time ? press one button left step, press other button for right step ? it is possible? He non have need of other Step Motor controlloer? all is integrate?
hello can you pleas explain me how can I make DC stepmotor circuit left and right rotation with time delay off 60 minutes between by using two microswitches and the type of proper electronic print board thank you
Can a soft switch be added through limit switch connection. Sorry if this elementary as I’m a newbie. Also what do I need to run a more powerful motor?
I really enjoy your informative videos, I’m in process of making a dividing unit with stepper motor, between 0 to 100, do you have any electronic board that I can use?.
I want to buy this product. But it's not available in india. Can you provide me this to India or suggest me a similar board which is available in India.
When connect the motor only works on full power from potentiometer, when I lower it just stop and do one step at a time super slow nothing in between. What can it be? Using a 2 amp motor
I change the stepper motor, now I’m using a 12v .35 amp from adafruit and now I’m able to use the potentiometer. Now the main problem is way too much vibration for my use ( DIY motorized camera slider)
@@dariuszroczek4068 remember that the board runs from 5-12v if motor is 5v when lowering the voltage with potentiometer will not respond because is going less than 5v.
@@hernanpacheco3016 Wow That is exactly what I am going to use mine for. Just ordered two today. Custom Made check out this video: th-cam.com/video/vkoiYt6pbGE/w-d-xo.html
Yes, i's a neema 17 motor, but the four pin connector that came with my stepper motor was wired wrong and the motor would not turn. Using I had to rewire the 4 pin connector to correspond to the coils coming out of the 6 pin connector plugged into the motor. One coil needs to connect to A+ and A-, the other coil needs to connect to the B- and B+ coil.
Bonjour guten Tag Nous avons une belle vidéo (sur une carte). Je suis heureux de cette carte dans l'Einsatz, mais si vous savez que ma machine peut l'être. À partir de 800 mA, vous devez le faire. Gibt es keine Treiberplatine damit ich ich ich einen grösseren Motor ansteuern kann. Il y a certainement un conseil pour moi. De très bonnes vidéos pour les SEHR guten Videos (avec le module MKS OSC V1) doivent être prises en charge
Exactly what I've been searching for Thank you
Why doesnt this work when you connect it to a buck converter? I have a 5v dc stepper motor and am using a buck converter to output 5v dc. Whenever I connect it to this board and press the button to turn the motor on, the D2 led blinks and doesnt turn the motor on.
Is there any way it can have the limit switch momentary start/stop cw and the other limit switch momentary start /stop ccw?
Hello, can I connect this 36820 module motor output pins A1,A2,B1,B2 respectively to the IN1,IN2,IN3,IN4 inputs of L298N driver module to driver a higher current stepper motor?
Thank you for reviewing this. Im making a DIY camera slider and this controller does exactly what I want to do.
Is there anything I can buy to power a larger stepper motor. Want to use the jog mode with limit switches so. Thanks.
Hello, If I need to run a stepper motor with higher current (1.8Amp) with what driver module should I connect this module? And how should I connect?
Excelente explicación, me parece lo mejor en diseño de control para estas aplicaciones 👍
Is there a way to make it jump back and forth between the two switches but with a timed delay?
Thanks a lot for the explanation!
I’ll appreciate it if you would view 7:25 on this one year old YT video and confirm if I understand the potential of using this layout to remotely tune my antenna.
As I understood, having adjusted the potentiometer for smallest ‘degree-steps’ and having placed jumpers properly, I can momentarily press one button, to ‘step’ the motor a degree at a time in one direction.
If I understood what I viewed correctly so far, then can this more-accurate stepper motor movement be controlled through a two conductor cable in some way using your setup as I referred to ?
(Though I can use the analog approach of PWM a DC motor with a two conductor cable controlled by DPDT wafer switch, I wouldn’t have the more desirable accuracy of rotation by degree steps)
hi im trying to find out ine thing.... so im using this on a generator carburetor. does the mode facilitate automatic stop after a complete motion. example.. if i have it set to 180 degrees turn i want it to top this may simulate the choke being fully closed and then i have my relay once the generator has started then the choke will return to the closed position going 180 degree the opposite direction i dont want the constant power oncthe motor once the position has changed
Hey - I have built a camera slider, but the control board doesnt have these cool options. Can I use a 2 wire stepper motor with this board? Does the kit come with the motor wire harness, and which color wires to use? For the limit switch, and I use a basic momentary push button switch? Also, is that wire harness included? thanks!
How would I connect this to a Tb6600 motor controller? Thanks.
Witam mam taki sterownik podlaczylem i u mnie nie dziala gdzie moze byc problem
How Ican connect the power to this machine from the sourc of electricity
avez vous une reférence moteur qui fonctionne avec ce contrôleur ?
When I install this units my stepper turn one step at the time but slow, like one click not really turning. Any suggestion?
Good evening, I would like to know how to connect the stepper motor and which motor you used
Hi.how we can control step motor like swing motor on air condition unit that with pressing the button it goes up and down and when press the button to off it goes to first position (down position)automatically?
hello, ive got that contral board but im faceing a problem. Im using it in that mode where it turns on or another way by pressing the switches,.. but by not pressing the switch the stepper does not hold position. Can u help me out solving this problem ?
How many Amps does the controller provide to the stepper motor? Also, are there heftier products to upscale and run a high torquing stepper motor or how might you go about that?
how to control steps movements, like lets say we have 400 circular points to move one by one and i need to move pointer in following example sequence starting from 0->10->240->45->28-> .......... -> 400 . How can we automate this ..
How did you connect the power? Can i use a USB POWER?
Can you please recommend control board for a 12 volt, Nema 23 & Nema 34 stepper motor?
As soon as I plug the motor all led lights up to RED. Then as soon as I remove the motor then the led cycle starts. What seems to be the problem?
Brilliant video. Thank you. Just in time. Subscribed. 👍
I’m having hard time finding stepper motor that is rated for 800ma. Will this work ok with stepper motor rated for 1A?
Fantastic video on the functions of the board. One question, yes, its been 3 years but maybe you can recall. Is there a way to make it start up in running mode. Forexample if the jumper was set to JOG mode and the run switch was bypassed to ON. Would it start running when power is supplied?
I tried two stepper motors and two controllers and the motor won't turn. The lights obey the speed control know, but no movement from the motor. Any ideas?
I am having the same issue, did you find a solution?
I also have this model but can you tell how many watt amp adapter you have installed?
In jog mode does the knob control the stepper? I'm looking for a simple knob that Wil spin the motor according to which way I spin the knob.
Thank you for sharing and very detailed info video, does the rotary knob will control the speed of the stepper motor to slow the rotation down while in stepper mode?
Thanks for this video, I have been looking for months for an alternative to arduino, for my grandson’s ramp lift (toy car), with the function start/stop, cw, ccw.
Over time I invested in several control but without success.
N is this right if using a radio controlled esc would it b possable to draw the 80 or 150 amps from it so u wont need so much extra power wen using like say a blender that runs on batteries n a solar controller or pmw
So does it randomly select what options to select when turning it on n off????
Do you have a circuit diagram of this pcb, I think I broke mine and run just on one setting with the high speed.
Dear Sir, can I interface this board's output with the DM556E Stepper Driver to drive a bigger stepper motor (NEMA 23 stepper motor)?
What motor you use? I try 12v one and vibrates to much, any clue???
hello, can I programmate it for use buttons for one step for time ? press one button left step, press other button for right step ?
it is possible?
He non have need of other Step Motor controlloer? all is integrate?
can i use 12V 5A DC Centralize Power Supply Adapter?
how many volts and how many amperes is the stepper motor used?
Does anyone know if any board exist to add to this to connect bigger stepper motor?
Thanks for asking. That's a really good question, I have been wondering about it.
Hello! Can I connect all this to batteries? (18650 x 3) Thanks
Can i use 6 wires stepper motor on that module
will it run a small 3phase high speed motor ?
Does work with a 1.3A 3V stepper motor ?
Hello, is there a way to control a servo with this ciurcuit ?
Sorry no, stepper motors only.
where can i buy it in Holland?
Outstanding demo. I assume this is a Nema 17. Can it be used on a Nema 23.
Can i use stepper motor and with that module as my wind shield wiper motor 🙏
Buna treaba! 👏👍
hello can you pleas explain me how can I make DC stepmotor circuit left and right rotation with time delay off 60 minutes between by using two microswitches and the type of proper electronic print board thank you
Is it possible connect to DRV8825?
Excellent,i am thinking to use it for car wiper with variable speed adjustment,can you guide
Please let me know from where I can get Stepper Motor Driver Control Board 36820 MS in India ?
Thank you so much. Very nice.
Nice video shot, thanks for sharing, keep it up :)
hi...very nice this board...so i can use it with 12v...???
what motor is that in the video ?thanks
It is a STEPPER MOTOR NEMA 17 42X42MM
Great video, very good work bro🇧🇷😉👏👏👏 subscribed
Dear sir, this is a very helpful video for me. But I need a same working driving board for nema 34 and 23.can I get it.
Nice and very useful vedio.
Can a soft switch be added through limit switch connection. Sorry if this elementary as I’m a newbie.
Also what do I need to run a more powerful motor?
I meant dpdt switch
I really enjoy your informative videos, I’m in process of making a dividing unit with stepper motor, between 0 to 100, do you have any electronic board that I can use?.
For high Q ham radio or shortwave antennas we need to see it make one step at a time for fine tuning
Sorry there is no single step mode on this part.
Nice perfect for my cheap Acention controller for my telescope
thk y so much for video nice
Are you shipping internationally?
thank you sir
I want to buy this product. But it's not available in india. Can you provide me this to India or suggest me a similar board which is available in India.
Brilliant. thank you.
Motor stepper yang di pakai berapa volt dan berapa ampera?
hello would it be possible to ask you about one of your stock products
What is the stock number, I will do my best.
@@mpjaonline Hello would I be talking to David the technician
Hello how can I drive a stepper motor having a current rating 1.8 Amps using this 36820 board? Please reply.
What is minimum speed. ?
Can i use in 1RPM speed..?
Hey there, I use low speed for my projects, so check planetary gearbox for stepper motor on internet. If it's helpful.
Please i want the name of motor 🙏🙏🙏🙏🙏⚘⚘🤗🤗⚘⚘
Hallo, would you please tell me the name of Motor ? Please i am waiting you 🙏🙏🙏🙏🙏
When connect the motor only works on full power from potentiometer, when I lower it just stop and do one step at a time super slow nothing in between. What can it be? Using a 2 amp motor
I have the same, did you find the solution?
I change the stepper motor, now I’m using a 12v .35 amp from adafruit and now I’m able to use the potentiometer. Now the main problem is way too much vibration for my use ( DIY motorized camera slider)
thx I have to find another motor less than 800mA
@@dariuszroczek4068 remember that the board runs from 5-12v if motor is 5v when lowering the voltage with potentiometer will not respond because is going less than 5v.
@@hernanpacheco3016 Wow That is exactly what I am going to use mine for. Just ordered two today. Custom Made check out this video: th-cam.com/video/vkoiYt6pbGE/w-d-xo.html
is we need any Arduino for this
please reply me ya.
No you don't, it works on its own
How can I contact you
Kaha milega bhai ye driver
Very awesome, would buy if I could but no shipping internationally so...
search on aliexpress for Micro Stepper Motor Control Module Board , you will get exactly that board mate :)
Cara pesannya bagaimana kaka
I am trying to run nema 17 but its not realsing enough power to run it?? Does any of you guys tried nema 17 stepper motor??
i tried but does not work...still looking for a solution:(((
@@mehmetfahrifurat6130 need intermediate driver , any solution?
@@mehmetfahrifurat6130 , on the video, looks like he is using Nema 17 stepper motor, is that right?
I''m using a 9 volt alkaline battery
Yes, i's a neema 17 motor, but the four pin connector that came with my stepper motor was wired wrong and the motor would not turn. Using I had to rewire the 4 pin connector to correspond to the coils coming out of the 6 pin connector plugged into the motor. One coil needs to connect to A+ and A-, the other coil needs to connect to the B- and B+ coil.
Bonjour guten Tag
Nous avons une belle vidéo (sur une carte). Je suis heureux de cette carte dans l'Einsatz, mais si vous savez que ma machine peut l'être. À partir de 800 mA, vous devez le faire. Gibt es keine Treiberplatine damit ich ich ich einen grösseren Motor ansteuern kann. Il y a certainement un conseil pour moi. De très bonnes vidéos pour les SEHR guten Videos (avec le module MKS OSC V1) doivent être prises en charge
😂😂😂
I have burned 4 off them ,and then I released why
Maximum amps is 800 m amp’s
😂😂😂😂
حرقت اربعة
وبعدين عرفت ان اعلى امبير
هو ٨٠٠ ميلي امبير
omg
Good job, like full, subscribed, @arduinomaquinas thanks 😉👍
Hello, If I need to run a stepper motor with higher current (1.8Amp) with what driver module should I connect this module? And how should I connect?