L298n Dual H-Bridge Motor Driver : DC Motors : PWM : Stepper Motors : Eye-On-Stuff
ฝัง
- เผยแพร่เมื่อ 8 พ.ค. 2020
- L298n Dual H-Bridge Motor Driver : DC Motors : PWM : Stepper Motor : Eye-On-Stuff
Please consider donating to my channel so I can make more videos for you:
www.eyeonstuff.com/donate.html
All my videos are here: / @eye-on-stuff5248
www.eyeonstuff.com
Please Subscribe and Support my channel.
Thank You
#eyeonstuff #maker #arduino - วิทยาศาสตร์และเทคโนโลยี
I don't understand why it's so hard for people to make a tutorial like this. Thank you! :D
have you ever made one?
Thanks for this, I didn't realise 5v was needed on power supply and 5v when driving DC motors from Arduino.
great video. learned so much about these little buggers. thank you
Good video on L 298.board. Without arduino. Simple to understand.
Well done, thank you so much sir.
Great ! Thank you !
Enjoyed learning from you.
Thank you my dude❤
thank you very much sir ❤
Good video, very well explained 👍
Thanks
I learned I could make stepper motors go faster by ramping up to the max speed specified and then go quicker with the signals which made the stepper go quicker.
new subscriber thank you for sharing always watching your video
Just to be clear folks, the contol inputs only support up to 1.5V according to the DataSheet. 5V is too much.
Question, i’ve been searching for an answer to my inrush current problems with a couple projects. I’ve been trying to rebuild a couple old cordless vacs with some lion cells. But the issue I run into is the BMS I’m using for these cuts power because of the inrush. All cells are balanced and high drain. Of course research yielded PWM. But I would like to use a controller without a pot that is 100% on all the time. Could I use this Module and leave motor one jumper in place for the 100% duty cycle and overcome my inrush issues? Or will this provide the same issue?
Thanks!
Thank you sir this might help me solve my robot problems
may I ask, what is the purpose of this PIC12F683 microcontroller in this circuit for?
You said you need to remove the jumper in order to turn the 5V output to 5V in. Then you show how a yellow 5V input is connected to the 5V header, while the jumper is still on. ???
Hello, If I need to drive a NEMA 17 stepper motor having a phase current about 1.8Amps, is this module can be connected to the stepper motor driver controller module 36820? If so how?
can i power 2 L298N motor drivers with one battery/powerplug(12volt) or should i use 2 separate?
what should the frequency be, for controlling the speed of the DC motor?
7:13 your welcome!!
Can you provide the code link and a circuit diagram of clockwise and counter clowise motor
Hello , i made an arduino controlled car using this motor driver and im able to control speed without pwm , how ?? Please explain
If you want to melt things or want to catch things on fire then please go ahead and use this with a stepper motor... Recommending that somebody uses for a stepper motor is a dangerous proposition because as you know it gets extremely hot with even the slightest of use of any separate motor. The manufacturer of this device should stop advertising that it can be used for a stepper motor although it can be used for separate motor it's very dangerous to do so and should not ever ever be used for a super motor.
You convinced me to use this, and drive the fan with a Arduino, hahaha😁
Can I bridge 2 L298n Dual H-Bridge Motor Drivers together to use 4 DC Motors Seperately?
Yes, two of those will in fact drive four motors. Technically, you can have four motors run of a single driver, though each of the the two extra motors will have the same output as each of the other two, due to the phisical pins they are screwed into.
This is epic! Me likey 🥰
Circuit