How to trim out a glass sliding door! [COMPLETE TUTORIAL ON CASE MOLDING INSTALLATION]
ฝัง
- เผยแพร่เมื่อ 25 ก.ย. 2021
- In this video, How to trim out a glass sliding door![ COMPLETE TUTORIAL ON CASE MOULDING INSTALLATION] I am going to show you simple step by step installation procedures for case moldings.
There is no other home improvement for the money, that can change the look of a room the way that trim can. Replacing the trim in your home may seem like an impossible task, however D.I.Y'ers even at beginner level can have great results with this project.
The tools needed to complete this job are minimal, A miter saw, nail gun, tape measure and a miter protractor. For the best miter protractor go to @SawsetTools and your miter cuts will be perfect.
Wake up an entire room with a complete re-trim and the transformation will worth all the effort you have put in. There are many different styles and sizes of the trim moulding family for you to choose from.
Case moulding
This moulding is typically used around windows and doors.
Base board moulding
This moulding is typically used in trimming the wall to the floor.
Crown moulding
This moulding is typically used for trimming the wall to ceiling.
Chair rail moulding
This moulding is typically used to trim the wall about 30 inches from the floor. It is an excellent way to break a wall for two different paint colors.
The only thing left to do is pick the moulding out and install it.
Detroit D.I.Y Apparel has arrived please take a minute to check it out using the link below.
detroit-diy.myspreadshop.com/all
And as aways thanks for watching and please feel free to reach out with any questions. detroitdiychannel@gmail.com - แนวปฏิบัติและการใช้ชีวิต
First and foremost thanks for the info! Very informative. I had a similar situation at the cottage re: door moving when slammed closed. After the shims were placed, I filled the gap with low expanding foam to guard agains draft and cold. In my area, Crystal Lake Ontario, the temp in the winter sometimes dips below 30 degrees celsius.
Great video, simple and no over explanation
Just what I was looking for. Thanks a lot man.
this is so helpful, thank you for your knowledge
so many videos about trimming out normal interior door frames but how about exterior patio/sliding doors? this is the only one i could find
Most doors come with the exterior trim as part of the door. Especially glass sliding doors of the new construction type. If it is a replacement door it would use the existing trim from the old door.
th-cam.com/video/uA9U5EaOt-w/w-d-xo.html
In this video the door was installed and I do show the flashing being installed.
Nice job
watched in in 2x speed... its like a kid that knows what hes doing haha
Thank you
Thanks for all the tips.
Thank you!
Loved the video! Is it possible to nail the case moulding on without the 1x5 piece of wood you used to fill the gap in the previous step?
Yes there are two 2x4's along each side of the door if it was framed properly. Thanks for watching.
@@detroitdiy thank you! much appreciated
How about the outside of the sliding door???? Do it need to be trim as well??
th-cam.com/video/uA9U5EaOt-w/w-d-xo.html
great video, did I miss the trim work for the exterior?...tkz\;]
The door came with an exterior J channel. The siding slid under it.
@detroitdiy no overhead coverage so I have to ensure flashing all around... tks again🤔👍😎
th-cam.com/video/uA9U5EaOt-w/w-d-xo.htmlsi=L84Gx32q_ICUVFT0
The video I just shared in the form of a link is the door installation and the flashing.
Dull blade would be the only reason for binding. In fact you can hear it.