STARTER / GENERATOR FAILURE ANALYSIS
ฝัง
- เผยแพร่เมื่อ 10 พ.ค. 2023
- PRODUCTS AND TOOLS I USE EVERY DAY AND HIGHLY RECOMMEND
JUMP N SURGE 2000 JUMP STARTER
amzn.to/42fLEQ8
MOTIVE X OIL FILTER WRENCH
amzn.to/40MjD1u
Copper spray a gasket
amzn.to/3Z9lonY
Help support my Channel by checking out my extensive parts store here on amazon
➡️ Check out this page from THEMOWERMEDIC1
www.amazon.com/shop/backwoods...
TOOLS I USE DAILY
MILWAUKEE 3/8 socket set
➡️ amzn.to/3N3ulda
1/4” socket set
➡️ amzn.to/3MTyQaf
Oil evacuations were delayed
➡️ amzn.to/3MQM33P
Lawn mower lift
➡️ amzn.to/38lKhsr
Fuel line clamps
➡️ amzn.to/3E0RI5u
#SMALLENGINE #BriggsAndStratton #Kohler #Kawasaki #Spartan #XMark #ToroHashtagClubCar #GolfCart #FuelLines #SmallEngineRepair #SmallEngineMechanic #SmallEngineRepairVideo #TH-cam #Repair #Video #DonnyBoy73 #EricTheCarGuy#Mechanic #MechanicVideo #HowTo - ยานยนต์และพาหนะ
Good starter / generator to save as a core or if you need a bearing or pulley some day!! I wouldn't rebuild it!! Some day you may be able to make two old ones into a working unit!! 😊
Believe I would buy a new one.
Replace the whole thing 👍
That is a 100% replacement.
Excellent
Never seen an armature worn down about an 1/8"? Bearings and brushes are easy, but not that?
That one was fried! Replace with a new one.
New !
The case in the steel bin. The core in the copper bin. Or is that done anymore?
I don’t think so. It all goes in one big pile.
Put it in lathe turn it down make a scraper from hacksaw blade clean the Mica out put new brushes & springs in
Heck no. New one is 75$
What should the voltage output be
13.8-14.5
Should it be steady or will it bounce up and down,I'm having an issue where the voltage drops under 12 when I'm under 5 or 6 mph and the gage is bouncing from 13.8 to 15 volts even at a steady speed of 12 mph,any help would be greatly appreciated
Right hand threads, look at the end of the shaft.
It’s actually keyed. No threads. Pulley should just slide off
First
Replacement is in order.
Replace it👍
Definitely nothing but replace it
The labor cost of rebuilding it with parts.
Buy a new one save the pully and any good screws.
This if you.
Needed if you loose one
Burnt electrical smell and differential fluid are aweful. Lol
Just replace it and be done
Replace it...
Just FYI, I was reading reviews of the cheap 140 dollar ish starters on Amazon and they aren't any good, I'd like to see what a real mechanic with experience has would say to that.
I didn't know they even still made starter- generators. I haven't seen one on any engine dating to later than the late 1960s.
Golf carts still use them
Replace it. Not wort money, time and warranty issues. Can’t break broke. Learn a LOT by tearing it apart. Take care
Buy a new one. Never had any luck with rebuild.
There still used on most golf carts. At $75 replace it, 20 years ago I was paying 3-$400 for a new one so we would always replace brushes. That commutator was worn badly, a lot of hours on it
You didn't show the magnets and windings inside the housing. I'm sure they're burned too. Not worth messing with. Junk it
There are no magnets they have field windings
Just order a replacement and save your time,losing money looking at it
That starter gen is smoked. Not a candidate for repair.
Order a new one rebuilding it ain't worth the time.. unless the customer is in a bend
Smells like cooked brushes to me?
recycle, scrap
I would buy a new because you don't know what else is wrong with it.
Buy new😂