i would guess zero - i genuinely have used 4 of these on my cars and not one of them has split, they are an incredibly stretchy rubber! very easy to use! :)
in MOST cases, the outer joint is a major pain in the ass to disassemble, it is also the most likely to fail. So being able to swap the boot with out separating the half shaft from the cv joint makes things a lot easier. I'll be trying this product on my next boot replacement.
Looks like you have to use a cv boot that is made for this because they aren't normally that stretchy. But the do have them in the usa but by a different name, prime line cv boot kit. Orielly auto sells them, in Phoenix Arizona they have them for sure else where IDK.
Man u pulled it thru like butter. One swift motion. I was watching this other video... the guy was struggling.. lol. This is how its done ppl! Some easy meant to be ez. Its all abt the hidden technique. Like everything else once u know that special move its butter
Thanks for this video mate it has made me more confident in fitting my cv boot to the o/s/f of my car. There is grease everywhere 😩 I have a question for you, does it need to be the lube provided in the kit or can you use penetrating oil ie WD-40 etc...?? As I have a cone, new grease and the jubilee clips to hold it to the shaft but no lube like you used. Could you let me know if this would work when I go to fit it? Any feedback and/or answers and tips would be very appreciated. Hope to hear from you soon mate.. Cheers 👍🏻
I can see this being useful if the drive shaft is to remain on the car, but if youve got it out of the car and in a vice, then it would be just as easy to do it the traditional way, ie: removing the joints.
Hiw do you pack the boot grease? He didnt show. I thought you took a needle into once it was installed. It doesnt appear this one was done that way? So how?
Because if you go to the next step, hitting the back of the cv joint with a hammer, the bloody thing is in your hand and you can use a normal boot which will slip straight onto the shaft.
If somebody like to purchase this cv-boot, clamps & etc. in USA - they can do it from www.viagra4cars.com in cv-boot section ! Or by calling: 1 888 558 2668 !
Another way of doing it without flipping the boot would be to place the cone on the inner joint end. Slide it right over then bring it to the outer joint.
In case anyone comes across this, if you search “draper cv boot tool”, it should come up with this or similar, as mentioned though, if you have something similar shaped that you don’t mind getting a bit oily you don’t even need to get one
What's the point? It takes 3 taps of a hammer to remove the cv joint or less than a minute to remove a circlip if it was one. By the time your spent messing about with this it could have been done. Also these cost a lot more to buy than a replacement boot for a few quid.
If somebody like to purchase this cv-boot, clamps & etc. in USA - they can do it from www.viagra4cars.com in cv-boot section ! Or by calling: 1 888 558 2668 !
I had three and they all have cracked or broken apart just enough to fling little specs of grease everywhere. I used bailcast which it seems they are the best, but still I would almost rather just replace with a solid one and not a split one after all the mess it has made over time.
More relevant today than ever. Aftermarket china axles are fucking JUNK. and people are realizing that rebooting your OEM axle as SOON as the boots get ripped is the WAY to do it. OEM axles are expensive!!
![จังหวะนี้ - เม้ก อภิสิทธิ์ [ Official MV ] จอนนี่มิวสิค](http://i.ytimg.com/vi/4gQRZCkRyiU/mqdefault.jpg)
What a brilliant idea! Definitely going this way next cv boot needs replacing
THANKS THAT WAS THE BEST INSTRUCTION I HAVE FOUND GREAT VID! THUMBS UP!!!!!!!!!!!!!
Bloody hell you made that look easy, hope it works as well for me !
thank so much ! this is the best video
i would guess zero - i genuinely have used 4 of these on my cars and not one of them has split, they are an incredibly stretchy rubber! very easy to use! :)
Please send me a link where can I get it from..thanks
Brilliant idea by the way!
THIS IS FANTASTIC!!! allot cheaper than a boot gun.
Vert good idea. Congratulations!
все гениальное просто!
you must be using an i Touch to check the softness of the boots, absolutely fantastic. There's always one.
Just tried this on the wife and mistress. They weren't to happy. But I had fun doing it....
in MOST cases, the outer joint is a major pain in the ass to disassemble, it is also the most likely to fail. So being able to swap the boot with out separating the half shaft from the cv joint makes things a lot easier. I'll be trying this product on my next boot replacement.
Thank you so much. I did the same on my Ford. Made a video.
Das ist Mal in die richtige Richtung gedacht 👍
Looks like you have to use a cv boot that is made for this because they aren't normally that stretchy. But the do have them in the usa but by a different name, prime line cv boot kit. Orielly auto sells them, in Phoenix Arizona they have them for sure else where IDK.
Have to do both outer boots. Thank you
Man u pulled it thru like butter. One swift motion. I was watching this other video... the guy was struggling.. lol. This is how its done ppl! Some easy meant to be ez. Its all abt the hidden technique. Like everything else once u know that special move its butter
do all cv boots work with the cone ? or do they have to be specific ?
nice one, cheers
excellent advise
Advice...
гениально! )) запомнил
Great video!! Not where can you buy that?
Looks like a bloody Traffic Cone! :)
Thought the same thing! Lol
Thanks for this video mate it has made me more confident in fitting my cv boot to the o/s/f of my car. There is grease everywhere 😩 I have a question for you, does it need to be the lube provided in the kit or can you use penetrating oil ie WD-40 etc...?? As I have a cone, new grease and the jubilee clips to hold it to the shaft but no lube like you used. Could you let me know if this would work when I go to fit it? Any feedback and/or answers and tips would be very appreciated. Hope to hear from you soon mate.. Cheers 👍🏻
where to buy kit
Always gotta buy the lube I use my wife’s lube works everyday
@@jojohack4926 you wife's lube is pretty good
прикольно, можно взять такую штуку от огнетушителя)
где? на заправке стырить?
Да я про это подумал но наши пыльники такой растяжки выдержат
Thank you very much for the video. Tell me where you can buy your product.
I wonder how it will go to mount a boot made from thermoplastic?
I can see this being useful if the drive shaft is to remain on the car, but if youve got it out of the car and in a vice, then it would be just as easy to do it the traditional way, ie: removing the joints.
I'd like to try this out, does anyone know where I can find it?
Thanks so good
Hiw do you pack the boot grease? He didnt show. I thought you took a needle into once it was installed. It doesnt appear this one was done that way?
So how?
onde podemos encomendar'?
Pinchi biejo loco mucho bueno amigo very good
Wonder if the same can be applied to rack boots so you don't have to remove the outter tie rod
If you could find a kit like this for it, same general idea
If the anther is damaged, it is necessary to wash off dirt, re-grease, without removing it do not.
where to buy and for how much is it?
These last well in my experience, not much fun to install in cold weather though.
These fit Pajero MK 2?
Ottimo senza usare il martello per togliere il giunto oppure usare l'estrattore 👍👍
in USA it's called the Slide About :)
SUPER MAN 👍
it is a good idea
why didn't you link the website to buy the actual product
Because if you go to the next step, hitting the back of the cv joint with a hammer, the bloody thing is in your hand and you can use a normal boot which will slip straight onto the shaft.
Where can I buy those good stainless steel boot clamps in the USA?
If somebody like to purchase this cv-boot, clamps & etc. in USA - they can do it from www.viagra4cars.com in cv-boot section ! Or by calling: 1 888 558 2668 !
Where do you buy a kit like this?
Where to buy??🤔🤔🤔🤔
Where can I buy these kinds of boots? I'm in Mexico some page
Impressive Video.
No OTT Bull***t ........ I've seen on other demo's.
Quick and Simple.
" Job / Jobbed ".
Quiero uno como hago para comprarlos
اريد اشتري وحده اين اجدها
Hi Felow, How are you doing? This is Leonardo from Brazil , were can I buy one of this on the web?
NICE
What type of boots you had
Where can I purchase this? You guys don't have a link in your youtube about section, video description or anything? You still in business?
How many cv boots have been torn for making this video?
Where can I find it ?
Do they have website ?
where can I buy this Universal stretch cv boot fitting Slide-a-Boot in US ? thanks
Подскажите Добрый день где такое купить набор
Are these still sold anywhere?
hey somebody now where i can buy one , i need its
Was this magic awesome
sorry, wer do i get that cv boot im in sa
Good afternoon, I'm Brazilian, what can I do to buy this product?
Another way of doing it without flipping the boot would be to place the cone on the inner joint end. Slide it right over then bring it to the outer joint.
GOOD !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I saw people change joint boot but do not take the driveshaft off.
Конгениально!
This was invented before the wheel right???
nice product! on a side note, if you are going to make more videos try using a mic. i could barely hear you.
Where do i get this??
Sorry, where i can buy it?
Is it just me or does it not give a clue where to get this product,,,, odd
You can use a funnel to do this job , no need for this cone.
In case anyone comes across this, if you search “draper cv boot tool”, it should come up with this or similar, as mentioned though, if you have something similar shaped that you don’t mind getting a bit oily you don’t even need to get one
Como comprar este cone
how is the durability of that boot compare to the regular boot?
Millennium CV-Boot will last longer then the original ! Read more at: www.viagra4cars.com
Or call: 1 888 558 2668
can guarantee 25 years ? :) My OEM after 25 years show first signs of cracks.
Where can I get it ?
И где взять такую штуку можно?
Я бы спросил -- где взять такой пыльник (чтобы не порвался)?
ДАуж, растяжка как у "резинки" в аптеках)
1:15 Look Jimmy, I'm Captain Hook!
I saw your joke. I went to the point in the video. All if have to say is I love you. Yaaarg, Peta'Pan!!
Buy where
Да базару нет Где такой пыльник приобрести.
Силиконовые пыльники продаются в автозапчастях,правда я на ваз2108 брал,ставил на део и шкоду.тянутся норм
Универсальный пыльник обычно так ставят.
Как при --40?
cuanto cuesta
What's the point? It takes 3 taps of a hammer to remove the cv joint or less than a minute to remove a circlip if it was one. By the time your spent messing about with this it could have been done. Also these cost a lot more to buy than a replacement boot for a few quid.
Try it on some Toyota drive shaft!!
Name of tool ??
😯 💡
typically commercials explain how to buy....
Freaking Brilliant! Where can I buy one?
If somebody like to purchase this cv-boot, clamps & etc. in USA - they can do it from www.viagra4cars.com in cv-boot section ! Or by calling: 1 888 558 2668 !
wer do i cat this
наши б пыльники разорвались на клочья если их так разтянуть
у нашего пыльника нет такой растяжки конус сплющится
Or just buy the ones you glue together. The glue is stronger than the rubber.
I had three and they all have cracked or broken apart just enough to fling little specs of grease everywhere. I used bailcast which it seems they are the best, but still I would almost rather just replace with a solid one and not a split one after all the mess it has made over time.
@@GMoney-B Same here!
this video reminds me of the video of the guy that sits on a glass bottle then the bottle shatters and he starts oozing blood outa his butthole
One man, one jar
To be honest I think you should turn off your computer and get out more
As advertised by Allan Partridge Do you like my traffic cone Ooooooo best not park there or you’ll be traffic conned.
Dont forget ,you wont get 1,000 miles out of them
More relevant today than ever. Aftermarket china axles are fucking JUNK. and people are realizing that rebooting your OEM axle as SOON as the boots get ripped is the WAY to do it.
OEM axles are expensive!!
ахаха я в шоке
English guy, not avail in N.America.
those boots seem way too soft.
I bet he
у нас их никогда не будет. ведь сто останутся без работы
Проктология..