Thanks for the shoutout! It was a little over three years ago when StonedEdge and I started working on this project together so we have both learnt a lot since then! The joysticks do have screw posts to hold them down, we just ended up not using them since the joysticks stayed put so nicely without the screws. I also wrote most of the OSD and controller software whilst Stonededge handled the electronics design and software setup stuff. The dock was entirely StonedEdge since I had no need for one but I can see he's done a wonderful job of it too! We've since split up onto different projects, Stoned is working on a new revision of the retrolite and I am making my own version of the Steamdeck using a NUC and doing my best to kickstart a TH-cam channel with it. Anyway, enjoy your new Retrolite and hopefully it sees more use than mine does 🤣
I’m kind of curious about the sd card, has any measure being taken to prevent the pi from shredding it? In my experience some diestros tend to absolutely eat the sd and it ends up failing after a few months of continuous operation (which is pretty out of scope for this).
You can actually see what's real quality... Love the gap around the device, but especially what even most manufacturers don't match, around the ports, is so even that it looks really next level.
This thing is amazing. I just wish they would use a non-custom battery. Nothing says "future e-waste" like a custom battery. Batteries are the one part that will eventually wear out - and making it custom means that I won't be able to get one in 5 years when it finally dies.
Replied to another post further up, but it's compatible with a common cell size (855080 4000mah). The one in the video is just some special ones Stonededge had made with a nice wrap on them.
Amezing craftsmanship. Its clare to see that both these people do something of the PCB and CNC each as work, becuase the talent is made over years is so visable by this kit.
But you just have to give credit to people being so knowledgeable about so many things that these devices encompass, each that took years to develop. Like we are speeding up when you have 14 year Olds able to understand and build these.
While the pi5 is right around the corner the pi4 is still an extremely capable board for stuff like this so it makes sense to design around the cm4 not only is it going to become cheaper to get a cm4 but you will get really good emulation at the lower cost
The problems with this are: - Find any Pi available - Plenty of more powerful and with better hardware Chinese consoles available (like Retroid pocket, and Ambernic brands)🤷♂️
@@nach0xare the retroid and anberbic devices really more powerful than a cm4? Which models out of curiosity? Been looking to build or buy a portable. Currently looking at building a pspi, cut up Wii (as I have spares), or something else pi based, but would buy something pre-built if it was interesting.
@@charlesswansonii9319 exactly...i had to wait till last year from 2020 to get one at retail price...almost the whole of coronavirus lockdown in Britain...Adafruit and sellers blamed chip shortages in Asia...we would believe that except the Chinese found plenty for their Asian contracts...and North America...that got the remaining shipping containers...Europe got the minimum...or pay double or treble for direct private sales...what can we expect from loyal Chinese...we only designed it in England
StonedEdge said "None of these individual parts are for sale unfortunately as I’m not making kits & don’t plan to anytime soon. I am spending most of my time working on a new revision" Jul 24, 2023
I'd definitely buy one close to the oled doesn't have to be oled but just thinner bezels like it. Also fast enough to run switch emu and I'd probably buy 3.
I'm glad you were able to get this video out. I know it was a long one in the making. I'll have to attempt assembling the kit I have. now that I have this quality how to video to show me how it's done.😀👍
Respect to them for putting this together, great project and good for DIY people looking to build a hendheld. But i do think the CM4 is a littl lightweight now that the Cm5 is around the corner. For the average consumer something like Retroid Pocket 3 plus also still makes more sense due to the better cpu and build.
This is pretty neat, good to see people still utilizing retropie and its probably a fun little project... that said with an upper limit of N64, this would need to be VERY cheap to justify a purchase with devices like the Retroid Pocket 4 and 4+ capable of GCN and at $150/$200
I woulda prefered if at some point you talked about what the dock sends to the tv, specially what res does it output instead of just glossing over the docks workings, which was by far the part I was most curious about this build
I just love how many options there are for portable gaming now. If sony wants to give up on their real portable system and sell a tablet with a controller glued on instead and Nintendo won't upgrade the switch, the community will come fill the gaps in the market that the steamdeck and similar devices don't cover.
This is cool... but ... if you want something like this, a Retroid Pocket 3+ (there's a metal version too) would be far more user friendly for you. This is for modding and craft enthusiasts. Nothing wrong with that I just suspect there will be viewers who just want the device and emulators, not the project lol. This is amazing though. So much custom work has gone into this. Plus you can't get that dock any other way!
I am so sorry but this fails right out of the gate by making us solder to a battery... that is incredibly dangerous. this needs to be designed better. That is just beyond stupid.
@@cgwworldministries83 there will be over current protection on the PCB. Short it and you'll see a little spark followed by nothing. You can buy batteries with leads on them already in this size anyway (which is what I did). Then you just need to solder the plug on one lead at a time. It's a piece of cake for anyone with a small amount of soldering experience.
You know for a cm project a phase change thermal pad might be a better option for a flat pad style heatsink. No fuss with the perfect amount of paste, no mess and you might just get better temps! I've never seen you use it, I've used it on a few projects and each time it shows lower thermals than kryonaut. It's anecdotal but I like it
I wonder would a RK3588 be better here, though now we have the RPi 5. That being said, i wish there's a way to mod existing phones to dedicated handhelds or SBCs to reduce e-waste and give a second life to phones.
You kinda-sorta can do that, just connect a mobile controller like Razer Kishi to the phone and play. It's better if your phone is supported by a custom ROM like LineageOS to ensure software updates, and if the battery is still in good shape or easily replaceable.
@@subrezon I have seen a hacky solution that involves mounting a heatsink+fan and a much larger battery. Just not a nice kit that you can 3D print+buy parts of the shelf.
I think the top button issue can be solved with a different button switch assembly that's surface mounted to the board. And I hope the analog is hall effect out of the box
The level of skill, effort and craftsmanship put into designing and manufacturing that device, only for it to mimic the least comfortable console of the last 10 years… mind boggling
Great project, but im especially proud to see "designed and assembled in Australia and Japan" on the box. We dont do enough design or manufacturing in Australia anymore - even a lot of design work is outsourced, so its great to see it happening even for small projects.
Can this do the Saturn? Also Ben any chance of an OLED screen option for those who want to pay more? Is there a non-metal shell option with those colors widely available? Will it be possible we see a CM5 or will it be throwing out too much heat? All the best for the creator and hope Ninty doesn't get pissy. This isn't a Switch and I hope the differences are clear enough they leave them alone. Much love Tito!!!!! Keep up the good work.
Well I was really interested until it got to the point where you have to mess about with soldering, as someone who has bad arthritis and not great eyes (I'm old, lol), I agree that they should do it as a fully built machine....it's like going to buy a pie from the shop and they just give you the ingredients, lol
I can’t understand why most of these projects don’t pay enough attention to sound. They install low-quality speakers that do not have a housing; they play low frequencies poorly. For example, they could use speakers from the iPhone se/7/8. I think the sound would still be better. I wrote this while watching, here the speakers have a housing, but it is unlikely to be sealed.
I think this is best playing all 70s, 80s, and 90s classic and retro coin op arcade games as an alternative for all male and female arcade video gamers.
That's really cool but as soon as I saw you installing those shoulder buttons I knew they would be an issue due to the design just using the plastic or metal bending to give it the springiness. The plastic ones probably do work better, but for how long? Im sure they will work those small things out eventually.
One of the designers here (just catching up on some comments). Have you ever looked at the shoulder buttons inside an xbox one controller? What about the buttons on computer mice? Plastic is used as a spring in all sorts of different products and industries so its definitely not an issue. The trigger buttons weren't the greatest design ever due to manufacturing limitations, but they worked when assembled correctly. They did sometimes need a little finessing to get the fit just right and I'm not sure how well that happened here. I think the metal buttons would've also made the feel of the trigger buttons worse as the membrane was never designed to be thick enough to support a button that heavy. In hindsight, we should've just used replacement switch lite triggers but its much too late for that now.
Hey man, love your videos. I've had a lot of successful projects thanks to seeing what you do. However, in this video, I feel like there's one major part you left out, and it's absolutely a big one. That is, battery safety! You mentioned getting the wiring on the Lithium battery correct or "it can damage your console" but that is a very, very significant understatement of what can happen if you do not wire that properly. Battery overheating, thermal runaway, and even venting is extremely possible when you're soldering directly to battery pads. In this case, who cares about damaging a console? You don't want to lose a hand, or have a battery vent when your face is near the console! That should be the focus there. You also didn't mention keeping the wires from touching eachother after soldering them to the battery either. If you're going to show a video soldering onto a battery like this, you NEED to cover that as well since hard shorting this type of battery can be catastrophic. Another part that should absolutely be included is a disclaimer that when you solder to a battery, you need to be quick with the iron. That type of battery is also extremely sensitive to heat when it is applied to small isolated locations. While this type of battery can run hot and the thermal runaway temperature would likely exceed any heat from typical use, applying a soldering iron to a contact is a different matter entirely. That amount of heat if applied too long to a battery pad, can also result in a catastrophic battery failure resulting in severe bodily or property harm. You typically don't have videos where you solder directly to battery terminals, so you probably didn't think to even mention this, but if a noob tries to follow this guide and messes up, they simply do not know how bad it can go very quickly. You seriously need to rethink either adding text to this to warn any potential user, or a complete re-upload where that is not only addressed but emphasized. I'm sure you do not want to hear stories of people getting injured from trying to do this, and that is a very real possibility for those new to this type of battery, or soldering in general. Most of your other videos you'll just brick a console if you mess up. In this one, you can seriously harm yourself or others if you don't. And that should be absolutely more clear.
One of the creators here! (just catching up on some comments) Just FYI, these batteries have a little BMS board on the end, that is where the wires are being soldered. You would have to try VERY hard to overheat the pack through these and a direct short to the output will simply trip the battery protection. This also isn't a kit and likely never will be, so to get to this stage in the build you'd have to be pretty profficient with a soldering iron and knowing what you're doing anyway, so I dare say most people aren't going to encounter this problem. Keep up the good work though, I do see a lot of people doing dangerous stuff with lithium batteries online so definitely doesn't hurt to warn people and I'd agree with everything you're saying if the cells were just bare terminals without any sort of protection.
My only beef is with the emulation power. If it can't do PS2 or GameCube, it's just a bit too weak for me. If There is a Pi5 CM in the works, or as mentioned at the end a RockChip Rk3588 version I will be ALL over this!
Personally I have a feeling it won’t be but I’m working on the Radxa board supporting the RK3588 for now. Not really much interest in the Pi 5 at this stage!
There's no excuse for making a new product in 2023 with bezels around the screen that are magnitudes bigger than the original PSP bezels. Screen size on handhelds is probably its main spec, as it directly affects both immersion and your eye health. And there's a lot of lost potential in screen size with those bezels, but somehow it managed to have a custom-made battery.
This is a cool project, If I have a chance to get a premade one that's further ahead(like has the 3DS emulator in or further) I might go for that. Been looking into handhelds built to be similar to a Switch but pocket sized & play older consoles recently so I'm glad to come across this.
Yeah not to mention most of our phones can play almost any emulated system PS2 and earlier. My 3D printed a case that let me connect to my jungle cat controllers to the sides of my phone, now I have a 8 inch switch essentially
The battery isn't proprietary. It was designed to fit an 855080 4000mah cell. Stonededge just got some custom batteries made with a nice wrap on them (and I believe they are 2x 2000mah cells in parallel, I could be wrong on this one)
I don't like the aspect of using a custom battery and not a commonly available one. what is in 10 Years? Will i be able to get a replacement battery? If using the form-factor of the for example Nintendo 3DS Battery you will be able to get a replacement but so?
Your channel the best. Every detail perfection. Im still trying many websites for games but no luck. Any recommendation gladly appreciate it. Thank you.
It's super cool, just don't see any reason to spend way more for less than a hacked switch, or retroid pocket 4. As a project though, I think they are doing cool stuff and I think it would be fun to put together as a hobbyist.
I honestly think they should not use that Nintendon't-ish Logo, knowing how trigger happy Nintendon't is they can get their lawyers to introduce themselves to Ben and Dan.
These pi consoles are nice projects and all, but suffer from "yet another device". A pi pico GP2040 android controller with a CNC shell would be a unique and convenient device. The gamesir x2 pro is excellent but having full control of the device would be so much better.
![BOWKYLION - วิงวอน (ex-change) [Official MV]](http://i.ytimg.com/vi/cLdnZWDaO-w/mqdefault.jpg)
![[TH] 2024 PMGC League | Survival Stage วันที่ 1 | PUBG MOBILE Global Championship](http://i.ytimg.com/vi/FVFT-PFwU80/mqdefault.jpg)
Thanks for the shoutout! It was a little over three years ago when StonedEdge and I started working on this project together so we have both learnt a lot since then! The joysticks do have screw posts to hold them down, we just ended up not using them since the joysticks stayed put so nicely without the screws. I also wrote most of the OSD and controller software whilst Stonededge handled the electronics design and software setup stuff. The dock was entirely StonedEdge since I had no need for one but I can see he's done a wonderful job of it too! We've since split up onto different projects, Stoned is working on a new revision of the retrolite and I am making my own version of the Steamdeck using a NUC and doing my best to kickstart a TH-cam channel with it. Anyway, enjoy your new Retrolite and hopefully it sees more use than mine does 🤣
I've been following your NucDeck videos without even realizing you were part of this project! Both incredibly impressive and ambitious!
Absolutely! You and Ben did an amazing job with this project! Your nuc steamdeck looks very cool!
I’m kind of curious about the sd card, has any measure being taken to prevent the pi from shredding it? In my experience some diestros tend to absolutely eat the sd and it ends up failing after a few months of continuous operation (which is pretty out of scope for this).
Great job guys, but honestly you should prepare for the incoming lawsuits ASAP, this looks similar enough for Nintendo to sue and cripple you.
lemme buy urs since u don’t use it so much @horchatamilker
Ben is a close friend of mine. I remember his first handheld. It was nothing like this. Years of work, and revision. Well done 👍✅
You can actually see what's real quality... Love the gap around the device, but especially what even most manufacturers don't match, around the ports, is so even that it looks really next level.
I remember seeing this months back and wanting to build one. I was looking build a handheld WII and I saw this. It looked amazing.
It’s definitely pretty cool! I’ll be looking towards the next iteration 👍
i just got three users with red and black on their pfp 3 TIMES IN A ROLL!
Steam deck?
Wow this is perfect especially with a Pi 5 overclocked to 3ghz. Can't wait for the CM5.
A new Macho Nacho video always makes me happy! Thanks Tito!
I’m happy that you’re happy 😁
This thing is amazing. I just wish they would use a non-custom battery. Nothing says "future e-waste" like a custom battery. Batteries are the one part that will eventually wear out - and making it custom means that I won't be able to get one in 5 years when it finally dies.
Replied to another post further up, but it's compatible with a common cell size (855080 4000mah). The one in the video is just some special ones Stonededge had made with a nice wrap on them.
This looks great and I wish I could afford to make a non-metal version. Would be a nice project over in the spring.
13:04 really just messed with my head. Top-left corner of the screen, while its right just was wild ;)
Haha omg I didn’t even notice that 🤦♂️
This isn't the kind of thing I would build myself but I would totally purchase one pre-built. That dock is just an amazing touch.
Amezing craftsmanship. Its clare to see that both these people do something of the PCB and CNC each as work, becuase the talent is made over years is so visable by this kit.
But you just have to give credit to people being so knowledgeable about so many things that these devices encompass, each that took years to develop. Like we are speeding up when you have 14 year Olds able to understand and build these.
While the pi5 is right around the corner the pi4 is still an extremely capable board for stuff like this so it makes sense to design around the cm4 not only is it going to become cheaper to get a cm4 but you will get really good emulation at the lower cost
Hopefully, scalpers won't make it near-impossible to find pi-CM4s like it had been with previous pis.
The problems with this are:
- Find any Pi available
- Plenty of more powerful and with better hardware Chinese consoles available (like Retroid pocket, and Ambernic brands)🤷♂️
@@nach0xare the retroid and anberbic devices really more powerful than a cm4? Which models out of curiosity?
Been looking to build or buy a portable. Currently looking at building a pspi, cut up Wii (as I have spares), or something else pi based, but would buy something pre-built if it was interesting.
@@charlesswansonii9319 exactly...i had to wait till last year from 2020 to get one at retail price...almost the whole of coronavirus lockdown in Britain...Adafruit and sellers blamed chip shortages in Asia...we would believe that except the Chinese found plenty for their Asian contracts...and North America...that got the remaining shipping containers...Europe got the minimum...or pay double or treble for direct private sales...what can we expect from loyal Chinese...we only designed it in England
@@nach0xAYN odin is a powerhouse
this is so cool i cant wait when the cm5 will be released and will much more power and will be an easy upgrade
Same! Cm5 will be amazing!
StonedEdge said "None of these individual parts are for sale unfortunately as I’m not making kits & don’t plan to anytime soon. I am spending most of my time working on a new revision"
Jul 24, 2023
Thinner bezel screen is a must for next revision IMO 😊
I'd definitely buy one close to the oled doesn't have to be oled but just thinner bezels like it. Also fast enough to run switch emu and I'd probably buy 3.
Or build 😅
I'm glad you were able to get this video out. I know it was a long one in the making. I'll have to attempt assembling the kit I have. now that I have this quality how to video to show me how it's done.😀👍
When you love what you do, THIS is the type of beauty that comes out. Specially with the help of a hommie. Thank you guys.
WoW this work like the ps5 Slim on net are just two great productions
The only thing I would want to see added in a future version is a larger laminated display
I really enjoy seeing these modern retro emulation builds. It's always good to have options, and I geek out over this stuff.
so close to what im looking for. also pretty ironic that during the last vid with the psp i said that i wish there was a version for the Switch. 😆
Amazing what 2 people were able to accomplish wow. This would be great for hobby builders.
Totally agree! It’s pretty amazing!
That’s awesome project. As usual it’s a lot more money than a comercial handheld pc
Would you think this is a good beginner project?
I would like to know this aswell
Respect to them for putting this together, great project and good for DIY people looking to build a hendheld. But i do think the CM4 is a littl lightweight now that the Cm5 is around the corner. For the average consumer something like Retroid Pocket 3 plus also still makes more sense due to the better cpu and build.
That little screen on the front is incredible!
This is pretty neat, good to see people still utilizing retropie and its probably a fun little project... that said with an upper limit of N64, this would need to be VERY cheap to justify a purchase with devices like the Retroid Pocket 4 and 4+ capable of GCN and at $150/$200
the aluminum and brass goes so hard. absolutely gorgeous.
I woulda prefered if at some point you talked about what the dock sends to the tv, specially what res does it output instead of just glossing over the docks workings, which was by far the part I was most curious about this build
I can answer that - 1080p 60Hz :)
I just love how many options there are for portable gaming now. If sony wants to give up on their real portable system and sell a tablet with a controller glued on instead and Nintendo won't upgrade the switch, the community will come fill the gaps in the market that the steamdeck and similar devices don't cover.
I love modding videos.
Thank you!
Thank you so much! Glad you enjoy the videos!
This is cool... but ... if you want something like this, a Retroid Pocket 3+ (there's a metal version too) would be far more user friendly for you.
This is for modding and craft enthusiasts. Nothing wrong with that I just suspect there will be viewers who just want the device and emulators, not the project lol.
This is amazing though. So much custom work has gone into this. Plus you can't get that dock any other way!
Ben & Dan really rock; didn't look into that project yet, but I love the secondary display, was considering adding one to my emulation rig as well
I am so sorry but this fails right out of the gate by making us solder to a battery... that is incredibly dangerous. this needs to be designed better. That is just beyond stupid.
That's a little PCB on the end of the custom battery, you aren't soldering directly on the cells.
@@cncdan short it and it will explode, no thank you. hard pass.
@@cgwworldministries83 there will be over current protection on the PCB. Short it and you'll see a little spark followed by nothing. You can buy batteries with leads on them already in this size anyway (which is what I did). Then you just need to solder the plug on one lead at a time. It's a piece of cake for anyone with a small amount of soldering experience.
@@cncdan not even going to chance it bro, it should have a spring loaded battery compartment. No excuse.
You know for a cm project a phase change thermal pad might be a better option for a flat pad style heatsink. No fuss with the perfect amount of paste, no mess and you might just get better temps! I've never seen you use it, I've used it on a few projects and each time it shows lower thermals than kryonaut. It's anecdotal but I like it
I wonder would a RK3588 be better here, though now we have the RPi 5. That being said, i wish there's a way to mod existing phones to dedicated handhelds or SBCs to reduce e-waste and give a second life to phones.
You kinda-sorta can do that, just connect a mobile controller like Razer Kishi to the phone and play.
It's better if your phone is supported by a custom ROM like LineageOS to ensure software updates, and if the battery is still in good shape or easily replaceable.
@@subrezon I have seen a hacky solution that involves mounting a heatsink+fan and a much larger battery. Just not a nice kit that you can 3D print+buy parts of the shelf.
@@cloudycolacorp Found the videos I was talking about. There's one by Geekerwan and another by Zac Build
I think the top button issue can be solved with a different button switch assembly that's surface mounted to the board.
And I hope the analog is hall effect out of the box
would prefer the shell with a dpad on top instead
The level of skill, effort and craftsmanship put into designing and manufacturing that device, only for it to mimic the least comfortable console of the last 10 years… mind boggling
Wow! You had 2k subs when I saw your first video and subscribed. You’re over 200k now, and so well deserved.
This looks like an awesome project. Can't wait for it to polish itself
Always really pleased to see a new video pop up, Tito! Thanks.
TITO: This Is The One 😊
Great project, but im especially proud to see "designed and assembled in Australia and Japan" on the box.
We dont do enough design or manufacturing in Australia anymore - even a lot of design work is outsourced, so its great to see it happening even for small projects.
That dock is the Bee's Knee's
Nacho time!
Woohoo!
This thing is really cool but I'm not touching anything that involves direct soldering to a battery.
was thinking the exact same thing, really good way to cause a battery detonation lol
Will this kit be available to purchase somewhere?? Why no mention or details on this?
Can this do the Saturn? Also Ben any chance of an OLED screen option for those who want to pay more? Is there a non-metal shell option with those colors widely available?
Will it be possible we see a CM5 or will it be throwing out too much heat?
All the best for the creator and hope Ninty doesn't get pissy. This isn't a Switch and I hope the differences are clear enough they leave them alone.
Much love Tito!!!!! Keep up the good work.
Well I was really interested until it got to the point where you have to mess about with soldering, as someone who has bad arthritis and not great eyes (I'm old, lol), I agree that they should do it as a fully built machine....it's like going to buy a pie from the shop and they just give you the ingredients, lol
This just reminded me of the aluminum switch lite shell, I want to buy one but i missed the production.
Nice to see a custom built handheld that isn't filled with hotglue or a million wires. Looks really nice.
I'm fine soldering everything, but I wish they sold a kit because sourcing parts can be a real pain in the ass.
So glad you used the perfect amount of thermal paste, could've been a real disaster.
I can’t understand why most of these projects don’t pay enough attention to sound. They install low-quality speakers that do not have a housing; they play low frequencies poorly. For example, they could use speakers from the iPhone se/7/8. I think the sound would still be better.
I wrote this while watching, here the speakers have a housing, but it is unlikely to be sealed.
It's a snap fit. You could glue the edges together if you were worried about it
WOW 😮 this thing is beautiful!!
MN, this is so cool! I adore that this handheld was made and presented by a passionate collaboration of creators and designers.
Ps Big fan!
I think this is best playing all 70s, 80s, and 90s classic and retro coin op arcade games as an alternative for all male and female arcade video gamers.
That's really cool but as soon as I saw you installing those shoulder buttons I knew they would be an issue due to the design just using the plastic or metal bending to give it the springiness. The plastic ones probably do work better, but for how long? Im sure they will work those small things out eventually.
One of the designers here (just catching up on some comments). Have you ever looked at the shoulder buttons inside an xbox one controller? What about the buttons on computer mice? Plastic is used as a spring in all sorts of different products and industries so its definitely not an issue. The trigger buttons weren't the greatest design ever due to manufacturing limitations, but they worked when assembled correctly. They did sometimes need a little finessing to get the fit just right and I'm not sure how well that happened here. I think the metal buttons would've also made the feel of the trigger buttons worse as the membrane was never designed to be thick enough to support a button that heavy. In hindsight, we should've just used replacement switch lite triggers but its much too late for that now.
This is pretty cool. But it's really brought down by that screen. Those giant bezels just look horrible and tarnish an otherwise beautiful device.
What an amazing project. That screen is amazing.
Cmmon Prod Productionsssss !!!!!
Look. I really enjoy the innovations that the community is doing. But please, for the love of God, can I buy a CM4 for retail..... Geez
TITO!!!! WELCOME TO RETRO RENEW 😁😁😁 Game on Bro!
have you heard of Frore systems airjet? I wanna start a petition for Nintendo to use it for their next console but I enjoyed this video great job!
Can anyone mod a shell to utilize this cooling chip in a current switch/lite?
Hey man, love your videos. I've had a lot of successful projects thanks to seeing what you do.
However, in this video, I feel like there's one major part you left out, and it's absolutely a big one. That is, battery safety! You mentioned getting the wiring on the Lithium battery correct or "it can damage your console" but that is a very, very significant understatement of what can happen if you do not wire that properly.
Battery overheating, thermal runaway, and even venting is extremely possible when you're soldering directly to battery pads. In this case, who cares about damaging a console? You don't want to lose a hand, or have a battery vent when your face is near the console! That should be the focus there. You also didn't mention keeping the wires from touching eachother after soldering them to the battery either. If you're going to show a video soldering onto a battery like this, you NEED to cover that as well since hard shorting this type of battery can be catastrophic.
Another part that should absolutely be included is a disclaimer that when you solder to a battery, you need to be quick with the iron. That type of battery is also extremely sensitive to heat when it is applied to small isolated locations. While this type of battery can run hot and the thermal runaway temperature would likely exceed any heat from typical use, applying a soldering iron to a contact is a different matter entirely. That amount of heat if applied too long to a battery pad, can also result in a catastrophic battery failure resulting in severe bodily or property harm.
You typically don't have videos where you solder directly to battery terminals, so you probably didn't think to even mention this, but if a noob tries to follow this guide and messes up, they simply do not know how bad it can go very quickly. You seriously need to rethink either adding text to this to warn any potential user, or a complete re-upload where that is not only addressed but emphasized.
I'm sure you do not want to hear stories of people getting injured from trying to do this, and that is a very real possibility for those new to this type of battery, or soldering in general. Most of your other videos you'll just brick a console if you mess up. In this one, you can seriously harm yourself or others if you don't. And that should be absolutely more clear.
One of the creators here! (just catching up on some comments) Just FYI, these batteries have a little BMS board on the end, that is where the wires are being soldered. You would have to try VERY hard to overheat the pack through these and a direct short to the output will simply trip the battery protection. This also isn't a kit and likely never will be, so to get to this stage in the build you'd have to be pretty profficient with a soldering iron and knowing what you're doing anyway, so I dare say most people aren't going to encounter this problem. Keep up the good work though, I do see a lot of people doing dangerous stuff with lithium batteries online so definitely doesn't hurt to warn people and I'd agree with everything you're saying if the cells were just bare terminals without any sort of protection.
"Custom battery made for this device" + "you have to solder this two wire connector on this tree connector battery" =/= custom battery to me.
in the future i want a 4k switch lite. the form is just goated.
My only beef is with the emulation power. If it can't do PS2 or GameCube, it's just a bit too weak for me. If There is a Pi5 CM in the works, or as mentioned at the end a RockChip Rk3588 version I will be ALL over this!
Seriously this is fantastic.
This is badass, but I have a feeling this Ben guy is going to get a visit from the Nintendo Ninjas for using their logo.
Are the dimensions the same as a Switch Lite; would cases, screen protectors and grips fit it if designed for the Lite?
Fingers crossed that the CM5 will be compatible.
Personally I have a feeling it won’t be but I’m working on the Radxa board supporting the RK3588 for now. Not really much interest in the Pi 5 at this stage!
There's no excuse for making a new product in 2023 with bezels around the screen that are magnitudes bigger than the original PSP bezels. Screen size on handhelds is probably its main spec, as it directly affects both immersion and your eye health. And there's a lot of lost potential in screen size with those bezels, but somehow it managed to have a custom-made battery.
This is a cool project, If I have a chance to get a premade one that's further ahead(like has the 3DS emulator in or further) I might go for that. Been looking into handhelds built to be similar to a Switch but pocket sized & play older consoles recently so I'm glad to come across this.
This is awesome! Time to pi up!
This is incredible!! Amazing!
This is cool, but costs more than a modded switch lite, which can play switch games plus emulators....
Yeah not to mention most of our phones can play almost any emulated system PS2 and earlier. My 3D printed a case that let me connect to my jungle cat controllers to the sides of my phone, now I have a 8 inch switch essentially
@@TGMisKillingTheMiddleClass
The flagships can even emulate the switch
Hello, I am excited about the handheld project. Is it also compatible with a Raspberry Pi5?
Thanks
Oh man were so lucky they made the battery proprietary instead of ya know using any of the already working ones
The battery isn't proprietary. It was designed to fit an 855080 4000mah cell. Stonededge just got some custom batteries made with a nice wrap on them (and I believe they are 2x 2000mah cells in parallel, I could be wrong on this one)
I don't like the aspect of using a custom battery and not a commonly available one. what is in 10 Years? Will i be able to get a replacement battery? If using the form-factor of the for example Nintendo 3DS Battery you will be able to get a replacement but so?
I think this part was a little misleading. It's a common cell size, Stonededge just got some made with a nice wrap on them.
That's a dope build
Hate the massive bezels but looks pretty damn slick
Dude your voice is perfect for this content.
Your channel the best. Every detail perfection. Im still trying many websites for games but no luck. Any recommendation gladly appreciate it. Thank you.
Awesome video as always Tito! I think prefer the PSP form factor over the Nintendo Switch, it just sits in the hands better.
Introducing the Raspberry Switch!
That little console looks very sleek.
This is really cool, cant wait till they atart making good oled screens to use with this.
It's super cool, just don't see any reason to spend way more for less than a hacked switch, or retroid pocket 4. As a project though, I think they are doing cool stuff and I think it would be fun to put together as a hobbyist.
I would love to see brass pieces that were made to look like wood grain
I honestly think they should not use that Nintendon't-ish Logo, knowing how trigger happy Nintendon't is they can get their lawyers to introduce themselves to Ben and Dan.
Somebody hire these people and make a western emulator handheld! With parts put together here so we don't have to ship stuff over seas so much lol
Nice, it almost looks factory, you just need to countersink the top and bottom screws
Those bezels are killing me i cant stand the sight of em....
Looks cool but a kit that didn't require a bunch of stupid soldering would be great
such well design, now i want switch lite metal shell :O
The four people that disliked were Nintendo and their fanboys.
And fangirls!
These pi consoles are nice projects and all, but suffer from "yet another device". A pi pico GP2040 android controller with a CNC shell would be a unique and convenient device. The gamesir x2 pro is excellent but having full control of the device would be so much better.
I love watching these videos. How can I be a part of the modding community? Where do I start?
Wait, why is the battery not just ready out of the box? That stupid lol