ฝัง
- เผยแพร่เมื่อ 26 มิ.ย. 2020
- DJI Phantom 4 RC low battery ...Repair Guide.
---------------------------
Like and Subscribe for more such content ahead.
---------------------------
#DJI #Phantom4 #Repair #RC #UAV #DRONE #Controller #Guide #DIY - วิทยาศาสตร์และเทคโนโลยี
![FIXED! DJI Phantom 4 Pro Remote Control Battery Charge Issue [Disassembly, Repair, Reassembly]](http://i.ytimg.com/vi/6pr6YhdnOYg/mqdefault.jpg)
I really appreciate your contribution it really worked as you explain and I just had to make a few adjustments to the resistor values. My controller came back to life. Thanks!
You’re welcome 😊.
Thanks man! Just fixed the remote which was having this exact issue. Remember to isolate the resistors before assembling 😉
You're welcome brother
For people looking for resistor values: 78k and 100k. Currently testing if it works, but so far so good.
Great
@@MSKtechy Please reply to other comments with correct values or mention that in the description
You genius buddy
Excellent👍
Thanks a lot brother
Thank you information helpful
You’re welcome
Nicee bro keep going full support 🙂💥💥
Thanks 😊
NICE 🤙🤙🤙🤙🤙🤙
Would you please and answer to the question : 2x100k or 2x200k are in parallel? The scheme and the text in video are not the same?
Hey awesome video, I have the same issue, did the fix you showed but didnt work, any idea what could it be? i have the GL300F that doesnt have any words in the pads but I used the ones in the same position as you did
Grab a multimeter and measure the wire continuity between one of the pads and the battery ground, do the same with another pad and the VCC of the battery and if both pads are short with the corresponding polarity of the battery then you have found two pads so far. For the third one you will have to the hit and trial with the other pads closer to the GND and VCC pads. Try this👍🏻
what voltage should be expected on Vcell and on VBat
Niceoooo
2x100k or 2x200k are in parallel?
Hi, nice video, thanks!
Same problem as yours, but my battery has 8,34V (99%, almost new :) ) what resistors can I use or what other solution? Thanks !
Hello. Found this video because I have the same problem. My battery is also 100% charged, could you find the required resistor value?
Try the same resistor values, if doesn't work then let me know.
👍👍😀😀😀
Dear author! You said in video "We need 80K and 100K. I don`t have 100K". What is correct nominal for resistors?
You can make 100k if you know the series and parallel math of resistors. Can follow this article - byjus.com/question-answer/why-is-resistance-different-in-series-and-parallel/
i'm ready for replacement chip charging
it doesn't work when i solder to the gnd pin, strangely when i remove the gnd pin it starts to charge, but the problem is the led always says full battery
The diagram at 4:57, R3 =R4 must be 200K and not 100K parallel (50K only).
When will be we need to replace battery, how much will cost for a new battery😢
I have a same issue here, after 1-2 years I’m not turn on the phantom. Omg have another easier ways to make the remote working? After charging 4-5 hours still the same. Only 1 led come on
Did this video solve your issue?
I had the same issue. I unplugged battery from the board (white connector), and plug it back in 10-15 seconds. After these actions controller was able to charge.
Hi. After that we remove the resistors?
No, they remain in there.
No, You can leave them there.
@@MSKtechy hi, when i leave them the problem come back
Where will the cells inside the battery of the drone be found, please tell
Inside the battery case.
Just use a Phillips screw driver to open your Controller and you will find the battery inside
Music very distracting imo.
Hmmm
Gta v series
???
what about gta 5
Hey make video on gta v like techno gamerz if will grow channel by editing
Check
Bro I am phd student of physics u should play game ☝️reply ms
You genius buddy
Excellent👍
Thank you so much bro😊.. I Really appreciate it👍🏻