So rename your video: "How to use a bearing puller kit" for people who cannot read instructions. I would like to know how to remove it without the kit.
It's just to show people how to remove it properly,because once over I didn't know to use a puller to remove them I don't think there's any other ways without damaging stuff, I've heard people putting grease in and even bread in lol to push the bearings out
Very handy these blind bearing puller kits ive got same one plus clutch holding tool from yambits & case splitter / crank puller believe me its best to get the write tools has it will cost you more in damage. when you making this other video anyway m8 on dt125r restoration
Defo right m8 a smashed a broke bottem end open with a Mel hammer when I was young cos a didn't have the tools just to see what was inside lol I used to use the yambits flywheel puller aswell to split cases it works just the same, did you get your casings on yet bro and am on making the vid I'm just adding bits to it each time I do sumit to the bike am expecting some engine bolts an gaskets today so a can put the engine back together today hopefully then it won't take long just need a newish back wheel and some new handlebars
@@2strokemxclassics no need to true the crankshaft before i put it back together haven't got round to it yet buddy & yes ino them clocks nothing inside them i seen this before on a bike thread & if you're looking for a nice back wheel look under wr125r rear back wheel
![ง้อ (ALRIGHT) - FOURTH [ TEASER ]](http://i.ytimg.com/vi/ya6MBfo-Wvg/mqdefault.jpg)
The tip about buying the bigger kit to deal with the broken bearings has already saved me a few quid. Thank you 👌🏻
🙏❤️👍🙂
So rename your video: "How to use a bearing puller kit" for people who cannot read instructions. I would like to know how to remove it without the kit.
It's just to show people how to remove it properly,because once over I didn't know to use a puller to remove them I don't think there's any other ways without damaging stuff, I've heard people putting grease in and even bread in lol to push the bearings out
Pack it with bread then compress with a suitable size drift and hammer.
The bread will push the bearing out.
Yeah I watch a man do it on a car bearing under the engine a few year back and it worked m8👍👍
Very handy these blind bearing puller kits ive got same one plus clutch holding tool from yambits & case splitter / crank puller believe me its best to get the write tools has it will cost you more in damage. when you making this other video anyway m8 on dt125r restoration
Defo right m8 a smashed a broke bottem end open with a Mel hammer when I was young cos a didn't have the tools just to see what was inside lol I used to use the yambits flywheel puller aswell to split cases it works just the same, did you get your casings on yet bro and am on making the vid I'm just adding bits to it each time I do sumit to the bike am expecting some engine bolts an gaskets today so a can put the engine back together today hopefully then it won't take long just need a newish back wheel and some new handlebars
@@2strokemxclassics no need to true the crankshaft before i put it back together haven't got round to it yet buddy & yes ino them clocks nothing inside them i seen this before on a bike thread & if you're looking for a nice back wheel look under wr125r rear back wheel
I used this and it just pulled out the cage, and then the puller would slip out of the bearing, the bearing didnt budge.
Good job dude!! (From Texas)
Thanks bro 🙂
Nice one matey thank you for sharing
No probs m8 thanks for watching👍👍
What motorcycle is this
Yamaha dt125 r /re/x. Yamaha tzr 125 tdr 125,ktm Lc2, gilera sc 125,derbi gpr 125 all use the same casings 👍
I need this tool
Ebay m8 inner bearING puller tool you will find them there just scroll down the list
Third!