ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
ฝัง
- เผยแพร่เมื่อ 1 ต.ค. 2019
- Please also watch the following playlist
• Topics about BRAKES
• Topics about CARBURETOR
• Topics about STARTING ...
• Topics about CHARGING ...
• Topics about TRANSMISSION
• Topics about ELECTRICA...
• Topics about TIMING/VA...
• Topics about FUEL SYSTEM
• Topics about COOLING S...
• Topics about Suzuki Mu...
• Topics about life adve...
In this video, I used the combination of two different ways to bleed the brake using a simple DIY tool. The first method is the vacuum wherein I slowly pull the fluid out of the system to remove the present of air (bubbles). To verify that there's no trap air in the system, I used the traditional way by pressing the brake pedal to push the fluid out and observe if there's no bubbles coming out through the system.
Please support my channel by visiting those links (tools & Parts)
below. I Bought some of them and I used it on my DIY car repair &
maintenance
OBD2 Scanner Professional Car Battery Tester Engine Borescope Camera
bit.ly/3dazwWg bit.ly/2N4VsYe bit.ly/2YdfKVR
Automotive Relay Tester Spark Plug Analyzer Stethoscope Car Engine
bit.ly/2YdtlfI bit.ly/3ddk9wa bit.ly/3fBxWyd
Piston Ring Compressor Auto Cylinder Leak Tester Valve Spring Compressor
bit.ly/2Y4aUtL bit.ly/2UMvFrR bit.ly/2AGmH8G
Digital Display Torque Wrench Automatic Torque Wrench Trisco K-547 Tune Up
bit.ly/30HTgh8 bit.ly/2WAMnf5 bit.ly/3bEyQaS
Radiator Pressure Compression Automotive Meter Tester Fuel Pump Suzuki F6A
bit.ly/2WAw0iI bit.ly/2yTfJN2 bit.ly/2zKxXjw
Engine Compression Tester PCV for suzuki for f6a Vacuum Pressure Gauge
bit.ly/3dQnWQF bit.ly/2ZaAG0E bit.ly/2X11PQN
VgateScanner MOHASHI Carburetor KENJI Carburetor
bit.ly/3bzlCMB bit.ly/2X0ToVI bit.ly/3bCqyjJ
Thermostat Suzuki F6A
bit.ly/2BqWScN
I used this method successfully, thanks to you there was no need to buy a professional tool, thank you very much, I recommend it has the same problem
For better results the syringe must be ABOVE the nipple and the tube must bend upwards because air travels upwards. Press pedal in slowly and hold for minute or so till bubbles get less. Release pedal and wait for brake fluid to flow into Master cylinder chamber before pressing pedal again. This will allow more air to come out. Start with furthest wheel from Master cylinder or ABS module. ....close the nipple BEFORE releasing pedal
I'm going to try your method
@@nsxt290 yeah that works for me.
Great video, great music, awesome way to bleed brakes. Thank you.
the music really is something else for this
Bravo, très bonne méthode... et ça coûte rien !!
i thought about it too ill give a try thanks for sharing
Yes its the right way . Excellent ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
Ok ito sir dagdag idea ko pra may lakas loob ako mag DIY ng break bleeding sir using sirange sir. Pero mukhang ok Ata sir kung medyo iksian konti yung hose sir pra higop agad yung fluid sir.
Problem is though is using a vacuum device it's sucking air through the thread as well
You can apply a little grease on the outside to create a little hydraulic seal. There is even dot compatible grease if you are concerned about contamination ;)
@Eff tee Pee you are correct. But I looks terrible. Also, you can put a bit of thread tape on the threads.
I seal the bleeder valve threads with teflon tape so you know when the fluid is airless before pulling a vacuum with a Harbor Freight hand squeeze vac pump.
This is an excellent idea.
Hi Sir You should temporary apply some grease around bleeding nozzle in order to avoid the syringe sucking air from the shop.
hello andrea, thanks for visiting my channel and spending time watching my video. that's a good suggestion. that time when filming the video, my only goal is to flush out old oil in the system at the same time the trapped air in the system so by pressing the brake pedal with the bleeder valve open, the brake fluid will be push and flow to the syringe as well as any trapped air ( if there's any). It's important to close the bleeder valve first before releasing the brake pedal just to avoid any vacuum effect when you release it. In my latest video about brake bleeding, I used special tool for this job. below is the link. Cheers!
th-cam.com/video/mLE1o3glVnA/w-d-xo.html
th-cam.com/video/Dgb0oIfdGSU/w-d-xo.html
Put a zip tie on the end of tube it will hold fast around the bleeder. And can go on and off as much as needed. Just pull and push
I had used a suction machine for mine...Simply magical lol
Yeah I made a suction machine out of old fire extinguisher, worked real good. I could also use it as a pressure bleeder through the master cylinder cap.
@@jsnjcnt bullshit
Sir ask lang nagpalit ako brake master cylinder repair kit...dapat ba talaga i bleed ung mga caliper salamat..wala kasi kapit ah
Thank you 🙂
Wonderful.
Wot about topping up the brake fluid reservoir ? From time to time so you don't run out and get air in the system
is it possible to reverse bleed so bubbles come out in the reservoir ? i do it on my bikes
genius
Wow
😲 Opération no GOOD, Retour bulle d'air.
Anu size tube?
hey man, it looked like you had some brake fluid in your air brake system there
yes your correct, thanks for watching, you can also watch this video th-cam.com/video/twJd__ynWB0/w-d-xo.htmlsi=DPQGyd8Ll_rP1gLs this video shows the effect of trap air inside the brake system. specifically at 6:02 mins of the video.
Most, if not all that air is being sucked past the coarse thread of the bleed nipple. Take it out and coat the threads with thick silicone grease and try again. Makes all the difference.
I wish you would've said where you bought this large syringe.
Its called a catheter tip syringe, lots of places online or if you have a vet they can order in a box or maybe give you one :)
pharmacy?
good day sir as kulang qng pag nag bleeding bah using syringe dapat ba naka apak yung pedal?salamat po
Boss bali sa video dalawang method po yung pinakita ko, mas madali at effective yung traditional method na tapak dun sa brake habang naka connect yung syringe. bandang 3:39 mins sa video yung traditional method.
sir salamat po sa idea
Pwede pa po ba isalin pabalik yang break fluid oh kelangan bago na??? Salamat po
Boss mas maganda kung bago na, para maiwasan yung contamination.
Soon the brake fluid will swell up the rubber in the syringe and make it inoperable.
Good pm,
Ask ko lang, kapag ng brake bleeding ka ba, dapat front and back tires, or pwd sa back lang kasi yun lang ang nagalaw ko? Thanks
Boss kahit yung sa back na tire, connected po naman yan sila. Tapos verify nyu po pag tinapakan nyu yung brake pedal para segurado.
@@UDoITchannel
Pwd ko i recycle ang brake fluid, sasalain ko yung luma para maalis ang dumi. Medyo limited ako sa budget eh. Thanks
@@UDoITchannelmaraming salamat, ang dali lang pala.
Boss pwede isa lang ba ang ebleeding mo kahit san sa apat na preno?
Boss mas maganda kung direct isa isa sa mga preno mag bleed, para mabilis ma flush out yung trap air, usually yung trap air ay nag dedevelop sa mga brake piston.
That's a lot of air for one brake line. I think your bleeding around the nipple. Just add a bit of silicon grease and employ a tie-twist around your tubing to create a better seal.
that's a good suggestion, I tried using cable tie to seal but it's difficult to dispense the older brake fluid on the small syringe, as you can notice, there is no brake fluid leak around the nipple. I have another video using 200cc syringe with flexible tubing that can fit and seal around the nipple, if you have time you can watch this video th-cam.com/video/Dgb0oIfdGSU/w-d-xo.html
no
Why not just inject brake fluid into the bleeder screw and force to air out of the top?
your abs module will say fuck to you
Classic Stang. Is that something you have done and if so did it work?
i do this on my bikes .no reason why it wont work .u can get a long piece of clear tube so u can stand in front of the car and watch the bubbles come into the cylinder
Works unless you have ABS. Those ABS units don't like this sort of thing and any dirt or rubber fragments in the fluid already in the line can easily ruin the ABS unit. Likewise, if you're pushing the pistons back to change brake pads on an ABS equipped vehicle, discharge the brake fluid through the bleed nipple, don't push it back up towards the reservoir (and ABS unit.
Sir nag chat po ako sa fb nyo pa check nlng po salamat po.
Wrong process