ฝัง
- เผยแพร่เมื่อ 20 เม.ย. 2021
- 2016 Coleman 5hp four stroke short shaft speed test.
Approximately 250lbs in boat including myself.
Without weight balanced out at front, average speed is 6-7mph
With weight balanced out, average speed is 11mph+
BALANCE IS EVERYTHING.
![[ไฮไลต์] แบดมินตันหญิง "เมย์ รัชนก" ไทย vs เบลเยี่ยม รอบแบ่งกลุ่ม | โอลิมปิก 2024](http://i.ytimg.com/vi/qfMROCoiKMY/mqdefault.jpg)
Good video! I keep a small deep cycle battery and a little Minn Kota 30 motor (for trolling or emergency use) laying on a floatation cushion in the front of mine to balance out.
What external fuel tank kit did you buy for the motor?
How are your launch wheels installed? Are the bolts accessible from the inside? I have a G3 1236 with the similar floatation behind the rear seat and I’m worried I’ll have to install them so narrow that they’ll interfere with the motor.
Hey does yours jerk into gear when u put it in first my has a really bad jerk when putting it in gear
How you doing thank you for your video question what type of fuel It’s better for the motor thank you
Ok thank you I was afraid I was doing something wrong and wasn’t getting enough speed from it
Yah for sure. Glad this helped!
Good vid
Hey thank you!
Thank you for sharing this video. I am curious about owning a 5 h.p. outboard with a 12 foot jon boat.
I think a 5hp outboard on a 12’ Jon boat is a great setup for smaller lakes and rivers. It won’t get ya up on plane but it’ll move you around plenty quick and they are light.
It will definitely get the job done he was getting 11 mph in a 10ft boat that is zippin lol too much more and it's just plain scary lmao
Hey, nice video. I have the same exact motor. How much did you pay for yours?
Hey thanks. I bought it for $475 and spent another $75-$100 replacing the internal fuel tank, fuel cap, impeller and fluids. The tank and cap were cracked while being transported.
Thanks for your immediate response. I paid 450 for mine. How difficult is it to change the impeller? I can’t find a video anywhere😢
@@standbackstandby200 fairly easy. You remove the two screws on the lower leg assembly (about where the water inlet on the leg is situated), the leg comes apart and you see the impeller on the driveshaft.
@@standbackstandby200 I Want to buy one. Where did you buy it?
@@THELIFEDREAMER.1329 resaler on OfferUp
How fast did it go? How long is boat
That boat is 12’ long and the top speed I got with the 5hp Coleman was 11.8mph
olles friend I need a water pump impeller from a Coleman 5hp engine where I can get it
Hey, so I ordered all the parts for my Coleman through this website:
colemanpowersportsusa.com
I live in Arizona and they have a warehouse here at:
1775 E University Dr
Tempe, AZ 85281
United States
Their number is:
+1 (888) 405-8725
@@r2bboats I need that piece a lot. I'm from Mazatlán, Sinaloa, and here I can't get someone, would you give me Would someone with a good heart help a thousand thanks
You can also use Yamaha parts because that engine is based on a Yamaha 5 hp 4 stroke
@@THe9-3MAnIaC oh awesome that’s good to know. Thanks!
Right. Same as the Parsun 5 HP, I think that's the motor's OEM..
How does it even move without those wheels on the back turning?
I’m sorry, I don’t know if I understand your question. But the wheels allow the boat to be pulled around on land by hand. When you launch the boat, you flip the wheels up and out of the water. Hope that helps.
@@r2bboats i was joking
Haha well played sir. Well played.
Very strange I have that same boat with a Colman 2.5 my top speed was 8.7 mph don’t gain much with 2.5 more horse power
Yah so if the weight in the boat isn’t balanced out the 5hp doesn’t have enough power to get it on plane. When balanced it’ll get on plane and do 11mph or more. But I’ve also noticed that the little 2.5hp push the boats surprisingly quick for what I initially expected of them.
I bet IF a 85 lb. skinny boy drove this boat -it would really G O ************
You're going to have to adjust the trim so it'll plain out
Yah I agree. And some weight in the front would help a bit too.
Dollars to donuts a old lawnmower engine and a long tail kit would be cheaper and faster.
Yah that’s something I actually haven’t tried yet. I know those long tail motors get up and go tho. And it would be a fun project. At some point I think I’m gonna try that out.