Set Garage Door Travel Max up and Down Liftmaster MyQ
ฝัง
- เผยแพร่เมื่อ 22 พ.ย. 2019
- this video covers a very important thing to check. Do you want to make sure that your garage doors not over closing and damaging your wall brackets.
Steps:
1. Hold rectangle button- Beep
2. HOLD down the up arrow until it reaches desired height.
3. Push rectangle button
4. Hold down arrow until it’s one inch before closing
5. Press up arrow once (door will automatically go up to set height).
6. Push down arrow once (door will automatically close to set close level).
IF your garage opener does NOT say wifi, try this add on that will allow you to make it work amzn.to/3HLEBDw
LIftmaster remotes amzn.to/3MnRJlJ
Disclaimer, I am an amazon affiliate, and may receive a commission for the link, but you pay the same price - แนวปฏิบัติและการใช้ชีวิต
Thank you, Sir. People like you spend the time to share your knowledge and experience.
The absolute best video on how to adjust your garage door on youtube!!! Thank you sir
OMG this video saved me $130 service call! Took me a whole 5 min to fix! Thank you so much!!!
Omg... Such a great tutorial. I live how you didn't take forever to explain useless stuff.
Danny, it's rare for me to find instructions on exactly what I need to know. Your video was exactly what I needed to finish installing wiring on the ceiling for my new table saw. Great Job!
the power glitched out while the door was in travel then it started to freak out if not for your video i would have been out of pocket $150 thanx you saved me $150 bucks
Excellent tip about stopping the downward travel about an inch before hitting the ground. That’s crucial to keeping stress off the mounting bracket. My mounting bracket busted because someone who said it wrong and I had to reinstall it. This pro tip really saved today! Thanks, Danny
Thanks for the tip about stopping the downward travel just above the floor. Your video is the only one that I saw that mentioned that. One video said you can use both arrows to fine tune the stopping points.
Danny you saved me at least $167 for a call charge they wanted for a 5 minute fix that you showed us. Also helped with the down door stress on the mounting bracket as mentioned before me.😀
Thanks! Your video helped me fix my door travel without paying for a service visit! I appreciate it!
Terrific video. Helped me fix garage door issues in less than 10 minutes and saved me a lot of $$ for a service call
Perfect instructions for what I needed, Danny. You were short and to the point. Totally loved my problem. Thanks again!
Thank you. This video was a help. My opener started behaving funny following a power outage. One thing I will add, if you have an opener with a battery backup like mine and you’re trying to completely reboot, the unit you will have to pull the battery. I was going through the same sequence as on your video, but not getting the same result. So I figured a reboot would be a good idea. I unplugged the unit, but then remembered that I had a battery back up. It wasn’t until I disconnected the battery and then plugged the unit back in. Then got it to behave the way it should while resetting it.
Thanks for the tip about stopping an inch above the ground. That solved my GDO issue!
Short, accurate, and to the point. Excellent!
Had the opposite problem where it only closed 1/4 way. Used the button setup accordingly and the garage door is back in order, thank you good sir!
Thank you man!! The installer had my door SLAMMING shut so hard.
Perfect explanation! Fixed my garage door issues in under a minute
Thanks! I replaced my garage door seal and ran into this problem. This solution saved me money.
Thank you for your video. I finally fixed my garage door. Excellent instructions and I learned a lot.
Perfect! Following your instructions solved my problem.
Garage door got froze to the ground in the winter and messed up the calibration. This helped me fix it in 5 minutes. Thanks!
THANK YOU much! Grateful for your instructions…
Straight and to the point, thank you Sir!
Hell yes! Thank you man I was able to fix my garage door with this video! Saved me some $$$$$
This info is still relevant in 2022! Thanks for the video!
First video that came up. Straight to the point and I nailed it on my first attempt.
That's slick, because I'm troublshooting my opener and when I saw that YELLOW COBRA! I have an 04 Mach1 lol
That’s cool. I also have a 2003 Mach 1 and stories on them th-cam.com/video/c9KxDNMTufQ/w-d-xo.htmlsi=vCXd0rAOwlxmx_DA
Neat explanation for a layman to understand. Thank you Danny!
aw,,0 ,,
Simple and to the point! This video really helped, great job.
Great guide, really saved me in a pinch. Thanks!
This was literally exactly what I needed, thank you!
Thank You So Much For Posting This !!!!! Perfect Instructions !!
Video was extremely helpful. I replaced the T bar seal on the bottom of the door and the door wouldn’t stay closed. I followed your video to the letter and bingo! It now works perfectly! Thank you very much.
I have a gap on the bottom of the door how do I fix this
@@urheiness7 Sorry, but I'm not the guy you should be asking for advise on your gap at the bottom of the door; I'm just a guy that followed the instructions provided by the video. I suggest you either ask the video provider your question or look for a video that talks to 'gap at bottom of garage door'.
This is exactly what I needed for mine. Thank you!! 🙏
Thanks. Straight to the point.
Thank you!! our garage door is bowing, and I am hoping this will help solve the issue!
FYI folks.....great video in deed.... However if you go up and down to many times to set the limits the motor can get hot and protect itself and shut off. I learned the hard way to wait 30 min and try again after the repair man was out telling me nothing was wrong, but it was over heated lol.
The 1/2 horsepower motor must be a Shetland pony instead of a Clydesdale horse.
Great instructions! Got mine adjusted after 3 attempts 😁
Thank you for sharing the video it was very helpful, I appreciate it. Thank you
Thanks For the Easy Instructions man
Omg - you saved my day man!! Thanks a lot for sharing.
Thank you very much for posting this. It was exactly what I was looking for.
I’m glad you found the video!
Completely lost concentration when i saw your Terminator 🤤😩🙌
Great instructions worked out perfect.
Bro!! You’re a lifesaver!!! Thank you! Easy peasy!!!
This also works for the side mounted opener. Thanks man
You're the hero we deserve!
You fixed my excessive force error. Thanks!
Thank you so much!!!! Worked perfectly
You’re a saint. Subscribed.
About to go do this right now! Thanks!
Short and very useful video
Thanks, worked perfectly.
Thanx for posting this!
Super easy, thanks !
Thank you very much for the video!😅
Excellent man!!! Thanks for your help
This is exactly what I’m looking for.
Nice and Quick, Thank you.
Thank You so much for posting this. perfectly done sir, I owe you a beer !!!
this was perfect thank you!
It worked. Thank you very much.
Thank you, very helpful.
Nice tutorial and nicer Cobra 👍🏻
Thanks for the video. I had an issue where the trolley was jammed up against the safety bolt on the rail close to opener unit. Had to remove the chain altogether to release the tension between jammed area and sprocket, and tried this adjustment. It did not register the up down limits properly. Found from this video and the liftmaster manual, that the trolley should be taken closer to the door and attached to the arm so that the calibration should always begin when door is closed. Setting the limits from door in closed position worked great
This exact same thing happened to me - however, I am able to set the upper and lower limits - but on the test run (final 2 steps) it travels up and stops at the open limit (opens) and then on traveling down (closed) it goes about 1/3 of the way and stops - giving me an audible alert of 5 beeps. I have verified that there is nothing binding, in the path of the door closing - and everything appears to be adjusted EXACTLY as my other garage door (10 feet away).
Any advice?
Thanks! This really helped!
Thanks brother very informative 👍
Thanks a bunch. I did that and it worked.
Great video!
Thank you so freaking much!!
Most excellent! Thank you.
Dudeeeeee thanks so much !!!!!! Life saver !!
Yep, that did it. Thank you!
Thank you very much.
Dude thank you. I was soooo annoyed. My garage was only closing like two feet lol.
Thanks man . Nice cobra btw !
Thanks. Great vid. U the man.
This is great. Because I let the down area nearly touch the bottom. But on the down it still goes a little bit. I will try this.
I just had that issue when I adjusted my liftmaster 8165w garage door opener when it over close I fixed my self with out this video
When you over shut garage door on 8165w it won't shut
Bro THANK YOU😂. MONTHS of agony!
Awesome just fixed a garage door gap!
Perfect, thank you.
No waste of time, perfectly explained. Some top g shit.
Thanks so much!!
Thanks!
Very helpful. Thank you!
Oh, hey Aaron 👋🏼
Thank you...
thanks so much.. You save me a lot of frustration and maybe even a marriage
Thanks 👍👍👍
Perfect thanks. Can't rely on apt maintenance to do anything right.
You just saved me haha
not my garage door
SVT cobra is FIRE
i like the 2 step system.
1st step: program limits
2nd step: program force
What if I only need to adjust how far up it goes? It's already going down fine so I don't want to mess with that. Thanks!
The cobra! 🔥
Awesome TERMNATOR!
I have a chamberlain and I think I need a travel module a/o logic board replacement.I’ve done the troubleshooting codes but to no avail.Any suggestions?
if i just wanted to adjust the down position. can o just do that or do i need to do both?
hey man wanted to tell you guys to have a safe and happy thanksgiving. in case you dont post another vid before then
Thanks! You too 🙌🏼
for some reason after i set the limits on mine i press up to test how far i set it to go up and it will only go halfway up, i tried like 5 or 10 times and cant get it to work correctly after i set it, im not sure why, any tips would be appreciated