Simple lightburn settings tutorial for laser engraving

Like and Subscribe!
check out these other cool channels!
Technivorous plays: / @technivorousplays8282
sci-fi and fantasy: / @sci-fiandfantasywitht...
3 party system: / @3partysystem496
Find 3dprinters and other cool Tech at:
www.amazon.com/shop/technivor...
SUPPORT TECHNIVOROUS 3D Printing:
TeeSpring Technivorous Merch!
teespring.com/stores/technivo...
become a channel member for youtube perks!
/ @technivorous
Paypal: [e-mail]
Check out my Patreon page: / technivorous
or you can buy me a coffee: www.buymeacoffee.com/technivo...
Send me a gwei! (ether address, all donations accepted!)
0xfFB33D2Af25909eB92dF5Da6236b69c4AFBaC692
send me a satoshi! (bitcoin address, all donations accepted!)
0xfFB33D2Af25909eB92dF5Da6236b69c4AFBaC692
Current Channel Goal: 25,000 Subs!

[@bobmartin6118]

thanks for just opening stuff without showing how or where you did this

[@anthonyloconte7835]

If you do a tutorial. Make sure you state what button or link you are clicking on to get where you are going. It's hard to see where your mouse clicked. Where is that DPI panel?

[@MrCatfarmer]

First time with light burn.
You tell us how to do it but I don’t see where you are getting these menus.

[@SteveH-TN]

Thanks for sharing 😊

[@joelrggizmo1373]

When I stop something a lot of times, I can never get it to go back to the same spot. It wants to start somewhere random or be off by just a tiny bit .

[@mohdzakiyusoff1195]

hi bro. thanks for the video. do you have a tutorial how to set laser head position for the effective cutting. Because my laser head is quite high from the material. thanks again.

[@joelrggizmo1373]

What are the light burn? settings for upgrading to? 20W ORTUR .offset for the larger laser head.

[@ckhoak]

Would be nice if I could find the DPI. Where does it reside?

[@TKR780]

when you have an image on your screen double click the SPD/PWR next to the photo photo layer in the Cuts/Layers tab

[@robertarmstrong2323]

The angle tip was helpful.. been using 45 like an idiot

[@maryvalephoenix]

Fyi to see the menu he is looking at you have to have a image with layers up then click the layer on right in top under cut /laser box

[@ahmadkhojastehzad2987]

HOW TO SET UP THE MAINE PAGE ON NEW PROJECT TO LARGER PAGE FOR BIGGER OBJECT ? THANKS

[@jennifermiranda2685]

What settings in lightburn will make me burn upside down and reverse? I am running a Xtool D1pro and if I have the letter B it will burn with the B reversed and upside down, almost like I'm stabding in front of the back of the laser. Hope I'm explaining it correctly. Thanks

[@fabriziosoriano3709]

Constan power mode what it is?

[@TheFalconJetDriver]

While exploring that page one thing that would have been worth mentioning was the line interval in mm. I have a Longer Ray 5 10 watt and the diameter of the laser beam is .060 compared as to most being.080. This will result in a finer DPI. Hey there is a lot learn in Lightburn and you have to start somewhere and this a good video to do that with. 😁🛫

[@pijanysamuraj]

hey great channel, would you tell me whats the overscanner and if any benefit out of it. like mine laser do is go around all the lines in the end of engaraving once again and I dont know why

[@Jake030292]

Overscanning means that it gives a bit of extra path on each side so the laser can slow down and speed back up and can reach the same power setting by the time it makes it back for clean marks instead of it starting the other way trying to power up immediately into the mark without full power at first. To better understand it, select it and preview your cut selecting Show traverse moves and it will show you on each side. Hope I helped!

[@Joeameturexpert]

I don't have image mode only line fill and offset fill.

[@HGANGHONY]

How can I change my homing speed?

[@Gabbywever]

How you open the laser settings I close it and I cannot find it anymore please and thank you

[@jessg691]

I don't know if you got your answer as yet since you posted 2 months ago lol, but I saw it today and you have to go to your windows option and select the ones you wish to see. Happy engraving!

[@Beerme-pl2ml]

Is your image mode set to dither for photos

[@Technivorous]

Grayscale usually but I have done either. Just remember to increase the dpi!

[@raywolfnolasco1277]

Need ur help

[@bretoner2]

What is the overscanning button for

[@Technivorous]

Over scanning allows the laser to run past the actual stop point of the burn, to ensure it doesn't spend too much time on the edges while reversing.

[@bretoner2]

@@Technivorous thank you

[@peterplantec7911]

You asked if you missed anything and I laughed…naw, you covered it all. I gave a thumbs up because what you covered, you covered well. Your presentation style is also excellent.

[@bryanproskiw5554]

Please stop moving the cursor around. It’s like trying to watch a fly flying around a room!

[@lonniedupont]

Sorry
That's not what scan angle is used for. Watch more videos instead of making them.