CR-10S Unclogging The Nozzle
ฝัง
- เผยแพร่เมื่อ 12 เม.ย. 2018
- Since a friend left me his printer a Creality CR-10S, to work on it and solves some problems, one of the problem was a clogged nozzle, this is a big printer let me show you how I have done so and the technic I used.
Videos that might interest you:
Retraction Calibration • Retraction Calibration
Extrusion problems • Extrusion problems
Cura 3 - How To Examples • Cura 3 - How To Examples
How To Dismantle The Hot End • How To Dismantle The H...
Top 5 Features Cura 3.2 • Top 5 Features Cura 3.2
How to Clean a 3D Printer Nozzle • How to Clean a 3D Prin...
Cura Time Saver Setting • Cura Time Saver Setting
You can also find me on :
Facebook: / franks-3d-shop-5670064...
Twitter: / franks3dshop
Instagram: / franks3dshop
My gear :
Amazon US (Commissions Earned):
Filament used PETG MG Chemicals amzn.to/2gWBJdnHictop 3D Printer model 3DP-11-ATL amzn.to/2yF9FEY
3D Printer Monoprice Select Mini V2 amzn.to/2yK9TdV
Camera Sony A6300 amzn.to/2gWmaTi
Sigma Lens 30mm F1.4 amzn.to/2gtzeyL
Neewer 7" Field Monitor amzn.to/2gWAsD7
Neewer Accessories amzn.to/2xcYobL
SanDisk Extreme 64GB SDXC UHS-I Card amzn.to/2yF34di
Manfrotto Compact Tripod amzn.to/2yEIZnv
IMDEN Omnidirectional Condenser Lavalier Microphone amzn.to/2xcY4cR
Flush cutter amzn.to/2nJhvrb
Deburring tool (brim cutter) amzn.to/2E9yzwA
Long Nose Pliers amzn.to/2BJNTT0
Tweezers amzn.to/2Bf5NvP
Amazon Canada (Commissions Earned):
Filament used PETG MG Chemicals amzn.to/2xdKo1v
3D Printer model 3DP-11-ATL amzn.to/2xdgyKq
3D Printer Monoprice Select Mini V2 amzn.to/2yKAUhn
Camera Sony A6300 Kit amzn.to/2gVrhD4
Sigma Lens 30mm F1.4 amzn.to/2xWO2kJ
Neewer 7" Field Monitor amzn.to/2zqL97K
Neewer Accessories amzn.to/2gVrshI
SanDisk Extreme 64GB SDXC UHS-I Card amzn.to/2gVrw0W
Manfrotto Compact Tripod amzn.to/2xVgChk
IMDEN Omnidirectional Condenser Lavalier Microphone amzn.to/2xX4lOs
Flush cutter amzn.to/2GVQNDr
Deburring tool (rim cutter) amzn.to/2E9xy7K
Long Nose Pliers amzn.to/2Bfu3hs
Tweezers amzn.to/2nLxpB6
Hi, I'm Frank my channel is all about 3D printing. I can't get enough of my 3D printer. I make everything and anything out of 3D filament (PLA, PETG and more). As I say a printer that is not printing is a missed opportunity.
I'll be doing electronics, mechanics, computer engineering, DIY, reviews and tutorials.
I update twice a week on Tuesday and Saturdays.
Subscribe to my channel, and don't forget to turn on notifications. - วิทยาศาสตร์และเทคโนโลยี
I love how you can explain it in 2 minutes
Quick, to the point and very precise....awesome video!
Thanks for this great short video. Helped me solve my first clog.
Me too, after a lot of good prints suddenly they began to fail. The extrusion was curling off and around. I followed this video and got a nice satisfying POP as the lump came out and left my nozzle clean. The extrusion then went back to being straight again :)
ugh what a lifesaver I have been fighting this damn printer for the past 3 days before I gave up and looked up a solution lol thank you!
Great Tip! Thank you!
Excellent video. Thanks!
This worked great, I actually bought a nozzle tip cleaner and that really did not work for something like this where the build up is inside the top of the nozzle chamber... thx
so glad I found this again!!
didn't even realize I was already subscribed from the first time I watched this years ago lol
great tip
Good hint :-) I realized earlier that pull out the bowden tube was impossible. Seems you have to loosen this fitting as you described
Hi, I did successfully removed the bowden tube, it can be a hard thing to do and can damage it in the long run, if you remove the fitting, just push the bowben tube forward you will see marks on it where it was in the fitting, remove those with a knife or sandpaper, than you should be able to remove the bowden tube when pushing the little bleu ring down. I prefer to leave it alone and just remove the fitting.
Yes thank you. Pushing down this ring didn't help to remove the tube. I will remove the fitting like you. I have mounted a fang cooling design so I have to dissasembly the whole thing first :-(
It’s not as hard as it seems...
thank you
Thank you
great! I always just remove the Nozzle and heat it up with a blowtorch in some vicegrips. and push filliment through it, let cool pull a few times untill its clean. I can really get my wire brush on it too to , heats up in seconds with a torch and the metal vice grips act like a heatsink so it cools down fairly quick too. :)
Yes it can be done that way too!
New sub 👍👍
Useful video. Only the temperature to pull the filament is too low. Try 120 degrees C.
cool goatie! :)
So I undid the top nut, but I can't pull out the bowden tube? Any suggestions?
i cant get the part you use the wrench for to come loose i’ve tried really hard
If my filament keeps breaking when I pull, should I try a higher temp pull?
Thanks
Yes you could or something is really jammed in there, or even your filament is brittle.
120 deg Celsius.
Hi, how long once to perform this procedure?
It can take 5 to 10 times depanding on the clog. Since than I use a dedicated setup just for unclogging, I will do a video about it.
Hello, I have A Creaity CR-10 with Dual Z Axis motors. The z axis goes up and down when homing but will not go up when printing. Is this a problem with my machine or am i doing something wrong in Cura ?
To be sure, try to print something already sliced on the original SD card...
My Boden tube is stuck in the hot end. Removed the fitting as mentioned but tube still won't come out of hot end. Tried pulling quite hard and that didn't work
Hi, you could push it from the other side if you dismantle the hot end assembly
Hi! What can Ido if my tube is stuck inside? o.O
Hi, I do not see my response so I will give it again, I did also encounter that problem, the tube was really hard to remove no mater how much I push down the ring on the fitting, I just unscrewed the fitting that holds the tube to the head...
@@Franks3Dshop Forgot to answer you! Thanks! ;-)
I did it exactly as shown in the video and the tip or the filament broke off inside the nozzle. I dont know what to do
You can try to push it up after removing the nozzle, try heating the nozzle at 170C to help.
I can't get my filament out it is stuck!!!?
You can try to unscrew the fitting holding the teflon tube on top of the heatsink, and see if it’s stuck inside the print head or in the teflon tube, if it’s in the teflon tube you could need to replace it, it is easy to find and doesn’t cost much, it has a inner diameter of 2mm for a 1.75mm filament.
Hi frank how you doing
Fine fine and you? Now if summer can begin, that would be nice.
Did everything except unclogging the actual nozzle. Smh