My friend got a 1050 ti and he was telling me that he didn't feel any performance boost. I went to check and i found out that he plugged his hdmi to the motherboard the whole time. He kept using the integrated graphics for more that 6 months
Do not keep your computer plugged in during a thunderstorm unless you have some king of high grade lightning protection... (battery power completely disconnected might be the only 100% safe way).
late af comment but - especially for first time builders, make sure to take your sweet time building everything, not just to enjoy it, but to make sure nothing goes wrong, triple check everything - my first build took 2-2.5 hours, but with the caution i took i had a successful boot on the first power up, and a month in still no issues
*Tip #1* - Run the EPS 12v Power cable for the CPU (4xPin / 8xPin) before installing the motherboard. Some smaller cases like the Corsair Spec-02 don't have enough room to run the 12v CPU power through the cutout on the back of the motherboard-tray once the board is installed. Running this cable before installing the board will ensure you don't have to run the cable across the front of your board. *Tip #2* - Lay your computer on it's side when installing the GPU, don't install/remove it while the chassis is standing up. This will help keep your GPU straight and limit GPU-Sag at the start. Some GPU will sag regardless due to the weight however some that would install straight will otherwise often have a little sag if installed vertically. *Tip #3* - Pre-bend your cables. If you need to put a bend in a cable to route it be sure to pre-bend it before connecting it to the header. You'd be surprised how many USB3.0 and SATA connections have been brought-in due to new-builders breaking them off. *Tip #4* - Cable manage your 24-Pin motherboard power cable first. This one can be subjective however I find that it's much easier to tie-down this large cable first and zip-tie other cables along the side of it. This helps especially when back-panel space is a limited luxury and gives you something to anchor to when manufacturers don't provide adequate tie-down locations. *Tip #5* - Maintain constant pressure when mounting LEDs that use adhesive. Of course everyone knows that having a clean surface is necessary for a good bond, it's also beneficial to hold them in-place for at least a minute to ensure the adhesive bonds well. This also helps squeeze out trapped air that may have been caught in between the LED source and the chassis. *Tip #6* - Do NOT over-tighten your CPU cooler. Previous generations Intel CPU's (Haswell 4th Gen and below) didn't really have an issue; However since Skylake 6th Gen CPUs, the substrate (PCB layer) is much thinner and is susceptible to being bent under pressure. I've only had a few PC's brought to me with this issue but it does happen. Needless to say the pins on the socket underneath were bent too. If the mounting hardware uses thumbscrews I only hand-tighten however is using a cooler that requires a screw-driver pay close attention to the force being applied. Some coolers have a "safety-stop" that prevents over-tightening but many do not. *Tip #7* - Use your PSU as a ground. Many don't have an anti-static workstation or a place to connect a grounding wrist-strap. However if you plug you PSU into the wall (make sure the switch is off/0) you can touch the PSU to discharge yourself or mount the grounding strap to the fan grill/honeycomb exhaust holes. *Tip #8* - POST test your components outside your chassis before installation. Almost nothing is more frustrating then completing your build and putting a ton of effort into your cable-management only to have your new rig fail to POST. You can use your motherboard box as a test bench and connect your components to ensure everything works before installing. *Tip #9* - Record yourself breaking the the seal, opening the box and examining the CPU Socket pins on the motherboard if ordered online or check the pins before you leave the store if bought locally. This is to help protect yourself and hopefully assist in the event of a return/exchange. All retailers essentially have a NO BENT PINS policy, "Pins are bent? You want to exchange? Pft SAD DAY FOR YOU!" This is understandable in the sense that it's, for all intents and purposes minus limited caveats, impossible for bad to arrive at the retailer with bent pins and you will be stuck with a nice paperweight unless you have good eyes and a steady hand. If your eyesight isn't the best or you have difficulty discerning all of the pins, use your smartphone to take a high-resolution photo so you can zoom-in on the picture taken for a much better view. *Tip #10* - Mount your fans for your radiator in a "Pull Configuration" if you use it at an exhaust and live in a dusty or furry environment. This will make it far easier to clean when dust/fur collects in/on the fins. Don't worry, whether in push or pull you don't have to be concerned about higher temps. *Tip #11* - Using an AIO Liquid cooler and not overclocking? Then show your GPU some love! I do alot of builds where people want liquid coolers on locked (non-K) CPUs and have awesome GPUs. Sometimes they specifically ask that the radiator and fans intake fresh air for lower temps; However this isn't the best option in most situations. A non-overclocked CPU will not benefit from slightly cooler temps but your GPU can/will. With GPU boost/overclocking one of your first ceilings will be the GPU's temperature. The lower your GPU temp, the more headroom your card has to run faster. (provided you're not hitting a power limit) *Tip #12* - Make sure when installing Windows 8/8.1/10 that your UEFI is set with "CSM"/Legacy Support/"Windows 7 support" turned off and that "Windows 8/10" is selected if applicable and not "Other". If your options include "Windows 8/10" AND "Windows 8/10 WHQL" select the prior. This will ensure that all four partitions are created and that all of the Recovery Options are available. If legacy support is enabled you will lose out on some features like "Reset your PC" and "Refresh your PC" without an install/recovery media. *Tip #13* - Unplug all other HDD's or SSD's besides the target drive for the OS. Windows likes to install the Boot-loader on a different drive rather then the target OS drive. This will help prevent headaches and downtime in the event that the drive Windows installed it on is removed or fails. Just reinstalled the OS on a SSD a few days ago in which the storage HDD died and the OS didn't have it's boot-loader. Of-course there are ways to correct this but I also wanted to disable the legacy support in the UEFI as he was also missing many of his recovery options. *Tip #14* - I need a new GPU. No seriously my GTX 780 is showing its age. :( Will update post with more tips when I'm not as tired, I know I'm skipping much more helpful info...
Aiml3ss Calam1ty tip #15 for you. buy parts on discount or black friday. Less cost for each part turns into better parts and a better overall computer for you.
1 - Be gentle with the HDD. It doesn't take a lot to kill one. 2 - if the GPU isn't going in/out, don't try to force it in. You will break the PCIe slot. 3 - if the PSU cable can't quite reach, don't try to stretch it as that may bend the pins/connector and cause damage over time even to the cable if it's a lower grade one. 4 - avoid cases without a bottom intake for the PSU. A cool-running PSU lives longer and has increased stability in some cases. 5 - The Intel stock cooler is enough for most CPUs - only invest in an AM cooler if you want a quieter solution or temps are going over 70*C 6 - Balance your build. If gaming, don't buy an i7 and a 1050/460 combo or an i3 and a 1070 combo. In both cases, you'll be better off with an i5 and 1060/480. 7 - Leave yourself RAM slots for future upgrades. What may seem like enough now may not be enough in the near future (I recently found this out after using 40 tabs in Firefox and using 6/8GB just doing that)
a bottom intake for a PSU is good if you have you case on a desk, then the air going through the PSU is cooler then pulling from the case, and will be even better for loggevity. Plus any case with a bottom PSU intake can be ignored, because you can still mount the PSU to pull from in the case.
@@MJRaymond from Vancouver, can confirm. When I lived further north, it was VERY strongly just Zed. Since moving here even I've found myself saying Zee occasionally
When building or upgrading, I like to always lay out the components in order of install. I used to make a list, but by having everything laid out (first closest) it helps me to foresee any missing components, oddities or needed mods.
I once assembles an entire PC inside my case, and things didn't fit QUITE right. I tried booting, and nothing happened. I was soooo confused and looked up the motherboard model and problems with it and detailed troubleshooting guides, but nothing worked. THEN I found out what motherboard mounting screws are for. Once my entire board was NOT short circuiting on the steel case, all worked like a charm :P
Same here. I never heard of the things despite a lot of reading up and following the manual. When I did try to install them, they just wouldn't fit at all. At best, they'd get stuck sideways. I hammered them through the metal and it was a huge ordeal. To be fair, only the PSU, case and RAM were new, the rest were old used parts, because I was impatient for the real stuff to arrive and I wanted to practice to avoid mistakes. So I wasn't all that diligent. And the stuff still worked. Maybe it's the expensive PSU. Still had problems with those dividers on my second build. Hate those things.
I did this with my first build, and I had a CHEAP (like, $40) motherboard! It surprisingly held up, after I had called my brother who was already into the building computers thing. That motherboard has since been sitting on carpet, used on carpet, and tossed around more than it should've been. Now it is my spare pc-in-a-box, for when my system gives out, due to it being a xeon X5660 (equal to i7 980x) at 4.7GHz and 1.4 volts, matching almost exactly the performance of a non-overclocked i7 6800k.
Was called as an SOS from a friend who was building his first pc, came over and looked at his motherboard. Left half on standoffs, right half touching the case. Luckily he didn't get far enough to turn it on before I got there
Always remember to instal 2 floppy drives, so that you can leave the OS in one drive and use the other, without the need to keep swapping the discs whenever you use a disc command. (such as dir)
Wrong (Donald Trump innuendo), "statox," or the correct way to spell it, static, does matter. Static discharge can ruin any component of the computer, which is why you must touch metal, preferably the case for certain reasons, in order to ground yourself.
Wait, what happen4s to your keybv4oard if you d4o? I'm asking fo4r no part4icular reaso4n.v Would that b4y any chanc4e cause shortcuts and therefore44 random letvters or number4s to appear, as well as cause4 keys to get st4ucvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv4444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444
dust filters and a aluminum mesh screen do wonders to keep out HAIR, dust, and BUGS dear god all the bugs that can somehow fit SO deeply in these electronics is terrifying.
Who cares if its neater, you are not gonna look at it. And even if it doesn't cover the whole ihs its not a problem because the CPU die is in the center where a dot of thermal paste would easily cover it.
You are supposed to use a very thin layer. I spread just enough to cover the CPU case. I really should wear gloves doing that (it is labelled as toxic (will kill you over time, not immediately)).
Thermal compound is meant to cover up pockets of air between the heatsink and CPU, as long as everything that needs to be cooled like cores is covered up it's good to go
When you spread you trap air bubbles. With line or dot, as the paste spreads it forces all air out. It is physically impossible for it to bubble. As for having to cover the whole ihs... You dont... Just the central bit. Wonderful thing about heat, it conducts through metal...
Not so bad, the trick is to do the cables first, then put everything else inside the case. The problem is when you put all the parts inside first then connect the cables to the component, you'll then try to hide the cables in whatever space you find. Count yourself lucky that IDE ribbon cable origami isn't a thing anymore
Marc Charbonneau Fair enough. I've only gotten into PC building in the last couple years or so. Arrogantly I decided to choose the Prodigy M for my first build thinking "Honestly how hard could it possibly be?" After about a week of cursing and swearing (that case was a damned nightmare) I gave up in defeat and decided to go with the Arc Mini R2 instead.
having bad cable management wont really cause you any performance problems. they have already done a video about this (maybe on LTT) where they jam as many cables as they possibly could into the case and it does practically nothing, so, unless your cooling solution is so bad that your PC could burst into flames at any point, having a few extra cables running through the case will do fuck all.
One thing I learned a while back is to add things to the motherboard before putting it in the case, cpu, memory & m.2 drives in particular Makes installation a lot easier
best pc building tip, "Don't half ass it". Don't cheap out on certain parts, and Spend a little time planning out the cable management. Also my biggest downfall, DONT FORGET TO SEND IN THE MAIL-IN-REBATES!
I think beginners tend to be tempted to go cheap on the PSU and motherboard because they don't see tests and benchmarks demonstrating performance boosts. I tell people if they are going to overspend and go overboard anywhere, it should be for a good PSU and motherboard. You'll get many more frames if your PC doesn't short out and fry your expensive new components.
I'm not familiar with that particular board, but I've had only good experiences with MSi motherboards so far. I personally tend to go with a higher priced board, but it will probably be OK if it has all the features you need and runs your RAM at a decent speed. I was talking more about avoiding off-brand junk like PSUs from companies I've never heard off that exaggerate specs and burn out in a few months. MSi has a very strong reputation for mobos. I've actually only bought MSi boards for the past decade. I look at other brands like ASUS and Gigabyte, but I ended up getting great deals on the MSi boards with recent builds.
happened to my friend too, luckily he was just upgrading cpu's and could use the old one to update it lol. but he was really puzzled on why the monitor wasn't displaying when he tried to use the i7
Back in 2014 I tried to build a PC for a friend. Not only did I mess with the front panel connectors, but also forgot to put the I/O shield, which I then forced in so I ended cutting my finger and had a couple of blood droplets falling onto the motherboard. Eventually, everything worked, but what a monumental sequence of blunders it was.
The worst thing i saw so far when i was working in a PC shop was a guy that put in the motherboard without the placeholders in place (aka screwed directly to the case). Not sure if this is common for new pc builders, but it was for sure a sight to behold. :D
Seriously?! How stupid can people be... "Oh, I'll just bolt this motherboard with all these component pin tips sticking out of the back directly to this metal plate. Nothing will short out." Anyone that dumb should never touch the inside of a PC case.
Here are some issue I ran into with my first PC build: 1.) forgot to plug in the system speaker so no beep codes when the following happened 2.) ram was in the wrong spot. needed to go in slot 4 and not slot 1 3.) PSU had significant wattage but I misread the connector types and it didn't have enough PCIE 6+2 cables to power my GPU. 4.) make sure your processor has onboard graphics before you try and use the inboard port while breadboxing. couldn't get system to post without using my GPU and got confused until I realized the difference between APU and CPU.
Tip: Just because two different sockets have similar names, doesn't mean they will work together. Example: LGA 2011-3 CPU on a 2011 MoBo or FM2+ CPU on an FM2 MoBo.
Some guy on the internet another example for this is that a previous gen skylake 1151 boards will not necessarily natively support the new kabylake without a bios update. so if you don't have a spare chip around you'll have a non funtionctional pc
+Dillon Lin Is it dangerous to make a bios update? I mean, I just bought a 1151 mobo but I was planning to return my skylake for a kaby lake ...I know I have to make a bios update to make it work, but is it dangerous?
Angelo Julioth Use the Skylake chip to update the UEFI/BIOS, then put the Kaby Lake chip in. And no, it's not dangerous. You can find many tutorials for your specific MoBo online.
Alright, I get it, so ...if my mobo doesn't come with the feature to update bios without CPU, It would be impossible to update bios and I would not be able to use the Kaby Lake one, so I should get the Skylake one at least to update bios. Thanks!
I can't tell are you advising for or against this. Personally, I think 'features I might use' would be a really good thing to consider, as probably the majority of upgradability is tied into what your motherboard supports, and otherwise, you need to replace said motherboard if you really do want these features later.
Ei'riġ Proinsias Dammantaċ Ó Gaṁna lol I cheaped out on my mobo and I got a b350m pro vid which supports 32gb of ram (2 channels and I got 1stick of 8gb so whatever) and it’s pretty limited
Actually, I would recommend it. 99% of the time the manufacturer is using something that will work, but not as good as some 3rd party thermal pastes that are out there. I use Arctic Silver most of the time. It works great and is inexpensive. Make sure the base of your CPU radiator or pump are cleaned well to remove the stock paste. A small amount of rubbing alcohol on a clean rag works well.
Yes you can but id say it's a waste of thermal paste, the cooler is not the best and changing the paste will probably just make it drop a few degrees tops if even that.
*PLEASE KEEP MAKING THESE VIDEOS, AND SIMILAR BUILD TIPS VIDEOS!!!* Thank you kindly, and be well! As much as I don't much need these videos (Since I am pretty well versed in everything you can possibly bork, after ~25yrs of porkchop build errors), they are GREAT for sending new builders to so that neither do I have to be there for their build, but additionally I prefer to teach people to look things up for themselves, as opposed to just doing it for them, or just telling them what to do...
Ohhh I once discovered I'd had the plastic film still on the bottom of the heatsink for YEARS. But never had problems with it though. Kudos to both Intel and Zalman I guess ':)
you can say that. Have forgotten them more then once, and one time I was proud of myself for putting it in before the mobo, only to later realize I put it in the wrong way... Then comes the fun task of getting it out without bending or breaking it... Fun for the family for all ages.
I don't understand why Motherboard manufacturers don't make the IO shield be part of the board. I think it was one of Linus's videos on the ongoing CES that showed a motherboard that came with a built-in IO shield, and all I could think of after seeing that was "why haven't they changed this to be the default for every brand?!"
TwilightWolf032 I agree! With the cutout for the I/o shield being standardized (at least, I'm pretty sure), I don't know why more companies don't make it part of the board. I'm sure it adds more cost than the cheap separate ones common now, but probably not by all that much.
Some things that have come up in my life as a certified computer repair technician (there's a lot of them): - Assemble base components before installing into case (if you have bad ram, video, MB, or proc). - Check graphics card clearances relative to the case as well. (Long card, short case) - Check fans / airflow. - Put thermal compound between CPU and heatsink. - Check that you have thermal compound, not thermal paste (this actually did happen to another employee). - Check amount of power supply connectors and length of power supply cables (this has happened to my backup machine). - Unless you plan on running Linux, you need to shell out cash for Windows. - Make sure you're grounded (cold weather means dry atmosphere, and dry atmosphere leads to static shocks). - You have hard drive storage, do you need a disc drive? Does your case have a disc drive bay? (This has happened, a lot) - If you're shelling this much money out for the computer, go the extra step and get a Blu-Ray drive! Combo, at least. - Do you need speakers? - Do you have a keyboard and mouse? - Does your case have front USB ports? Does your motherboard support these ports? (USB3 ports when board only has USB2) - Does your motherboard have enough fan ports? - Do you have external cards? Can they fit in the motherboard slots? (PCI / PCIe) - Do you have the right memory? (This has tripped me up as DDR4 was hitting the market) - Are those standoff screws already installed? Do they align with the motherboard you're installing? (MicroATX) - Secure the motherboard with all the screw holes. - No, those PC components won't fit in that Mac case... - No, those Mac components won't fit in that PC case... - Don't skimp on the processor. Intel Celeron/Pentium and AMD E just don't cut it. - For today's standards, get more than 4GB of memory if you can afford it. - Unless you're concerned about power consumption, don't use Green drives. (Don't use Purple / Video Surveilance drives either) - You don't need to hide the wires, but it helps. - Also check case width when using that large heatsink. - CPU fan goes in CPU_FAN on the board, not SYS_FAN, not CPU_OPT. - Microsoft Office will need to be registered with a Microsoft account. - You need antivirus. Only one. 2+ and you'll crawl slower than a turtle. - Add-on video card? Plug it in there, not to the motherboard. - Plug the power supply in with a satisfying 'click'. Brace the board if the board is too long.
You are actually quite helpful, Linus. Bought an already built PC recently, but I was just messing around and I took out all the front panel connectors. Searched a lot how to plug them back properly but couldn't find all the information I wanted. You cleared it up in under 30 seconds.
Building traps to avoid: First, install the right size power supply. Not having enough wattage will cause power surges, which could lead to system failure. And, if you're going to use a internal hard drive to backup your computer, make sure it's not a storage drive. That is to say, make sure the drive is bootable. If it is not bootable, then it will lead to you having more problems and spending more money.
Use masking tape on nice finishes when setting the case on one side! Touch up the inside with touch up paint (brush) if the inside finish gets chipped when screwing and installing drives. Moisture can seep into the case and prematurely corrode especially around fan vents. Coolmaster case I ditched had much rust in the front grill, second one I received, I took off all the plastics and left just the metal to cold galvanized primer then spray paint the color back and over 10 years later, not a lick of rust! The last case lasted less than five years. I've multiple systems and found with case screws and screws in general, 3 in 1 Oil the threads, tighten then back out a a less than a quarter turn. Two things it does: protects the threaded metal parts and easier to untighten at a later date.
this video is obviously for less experienced builders. it's not shit just because it's not useful info to *you*, there's alot of people watching this channel you know?
krelsen7 I came from reading other's stories on forums years back for my first build during the Nvidia 8800GTS 320mb GPU days and found out GPU is literally EVERYTHING. It took my my 4th GPU for a solid one where I can comfortably jam any game for the next several years to come. I currently use the R9-390 8gb GPU
Some thing that has really worked out for me and alot of people do it the other way around; After installing your motherboard (with ram, cpu installed) do your cable management and kabels before anything else. When everything is installed you will have a hardtime plugin everything in. Make it nice and clean before installing any other component after your motherboard is set. After all cables are ready and plugged and managed than hook up your graphics card, cooler, harddisks, and powersupply, Make sure you leave some space and are able to move your cables a little and that not everything is super tight. Goodluck building.
Make sure the gpu you buy can fit the case if you buy the gpu that can't fit your case you are scrued then you need to buy a new bigger case for example you have a micro ATX case and you buy an gtx 1080 that could probably not fit so take a look on that
I was so excited when building my current PC I forgot to plug the power to the gpu and spent an hour trying to figure out why I wasn't getting any sort of display xD
A pc trap i would avoid that might not be so apparent is impatience. You finally have all your parts and youre excited. Youve watched a million build guides, you know exactly what to do and you just want to put it all together as quickly as possible and start using it. It seems like it goes without saying, but dont rush your build. tried to rush my 2nd build, forgot to install the back plate for my air cooler and created a bunch of avoidable problems.
dont ever ever buy a cheap power supply. I got the hx1000i in platinum efficency, and my build uses between 1/3 and 1/2 of its capacity, which is fine. I spend very much money on the supply, but it was worth it. A friend used a cheap one on 3/4 capacity and had following problem: the supply had enough over all wattage, but ad he installed 4 graphic cards, his use on 12V was much higher than the use of the other voltages. as he powered everything up, he suffered from the pc spontanously being powerless when loading a big game, and this damaged the cheap supply so that the 3,3V raised to 3,5V and that burned his motherboard and other components. remember me buying an expensive power supply? well my friend saved 250€ by buing a cheap one.. but now he completely destroyed 1200€ Hardware.
WATCH OUT FOR THE MOTHERBOARD STANDOFFS! If you have one in plus it may fry your motherboard. Trust me, I experienced it. There was one under the south bridge and it killed my PCI slots and my GPU as well. RIP MSI HD6850 😢
@@pianosenzanima1 when you Not need them yes Your Board can touch one oft These like bence bokor says the harmles way it would fry your Motherboard or it would set the hole case under electricity load... ans this is dangerous.. and it can kill Not only pc parts ... i was toss throug the room and woke up at the hospital because i forgot One of These things under my board... Sorry for my Bad englisch :-/
Linus I have to give you a kudos on your video compression abilities. I can watch all your videos at 1440 with no lag or skipping. I can't do that with any other tech vids.
my tip - make sure ram is actually pressed down and properly in the slot. sometimes it seems it is but isn't I've ran into a couple times where a laptops sodimm somehow popped out and caused the laptop not to boot.
Adam Khan rofl I installed 2 extra Ram and my PC wouldn't boot. Eventually , monitor popped out with a message "overclocking error" so I went to BIOS on that single run to underclock everything. After that, the PC won't display any signals. It took me 10 minutes to figure out that one of the ram was a bit higher.I pressed it down and made a small "pop". Hallelujah!
i remember one time my PC wouldnt boot and for like 3-4 hours i was trying to figure out. reinsterted my cpu, checked all the cables. and then turned out to be the ram slot i felt so stupid since it was the last thing i expected
first time builders top tips. only install one stick of ram for first boot (in correct slot refer to mobo guide). check all your component when built using memtest usb key, prime 95 etc. buy mobo with easy debug led, makes life a little easier when troubleshooting. ensure your bios supports your cpu. Do not buy more than you need, learn about chipsets and the different features they offer. use afterburner to monitor temps of built pc. invest in a good case. ensure your cables are tied and out of the way of components inside the case. plug monitor into the gpu not the mobo. to save money buy a cheaper (reliable brand mobo) as you can often make up for a lack of ports (sata etc.) with mini pcie adapters. And most important, Get 16gb of ram or at least one 8gb ram stick (so you can upgrade later without buying 2 new modules) if you plan to play AAA games. Also, the rx480 is a beast at 1080p.
Sorry to hear that, i was already planning to go out and buy the parts this week and i realized the gigabyte B360M doesn’t support OC, thank god Linus🙏🏻
TL;DR: 1) front panel connections: diagram on motherboard(MB)/manual shows polarity. pins: colored wire, or embossed arrow positive 2) air cooler: check CPU socket and case specs (might not fit in size wise) if it fits. 3) overclocking: need unlocked CPU (intel: k or x series), need MB with suitable chipset. (need chipset name with Z or X in it) 4) during assembly: put in I/O shield in case first and bend all needed tabs! 5) peel protective film on bottom of heat sink
All modern CPUs have thermal protection so they throttle when they hit their max operating temp (usually 100 degrees) so it is safe to run it without a fan, it will of course throttle all the time and it is obviously not recommended to do this.
It was not until I started my adventure with the creation of the PC. Currently, even the wiring I have arranged, no longer commit such errors. I was much younger.
How about telling us how to avoid whatever it is Luke did in that Coolermaster case review / build video? No seriously though, tell us what happened so I can never do it! You can't just ignore an elephant in the room that big!
Good tips. Something that I do on a new build is add filter material on the fans and all open areas on the case. Dust and moisture is the second worst killer when it comes to PC's appart from heat and transient switching surges.
Thank God I decided to go through these videos as I was falling asleep! I jolted awake about the size of the CPU cooler, checked the specs and realized it would have been 2mm too big! Planned on building it this weekend. Luckily I was able to get a quick order in to Amazon for the right size and cancel the other one before they shipped it out. 🤘😎👍
Something to avoid, when using SSDs which are mounted in the back of the case, look for power supply cables with no pieces sticking out (mine has this annoying plastic rectangle about one cm thick and I can't fit the back panel on... being the noob I am I tried to force it and now I am starting to pull the pins out of the cord, my solution right now is just no back panel
My tips: -Don't cheap out on the power supply. Make sure to at least have a switch on it. Yes some PSU Don't have them. -Don't buy a prebuild. And if you do, Just buy/get installed some pieces you don't feel comfortable handling yourself if you are a beginner. Buy the other paets at different price points anywhere online (well not anywhere but you know). -Don't get mustard ketchup cables. There are plenty of pretty options. -Add dust filters to your intake fans.
Nidhogg84 That was also my thought, but on my PSU (a EVGA NEX750B) you could! It is a semi-modular PSU and you could plug it in the wrong plug on the PSU side ...
It may be plugged into the PCIe power connector area of the PSU. On my PSU: the Corsair AX860i, the area is designed 6+2 PCIE & 4+4 CPU. The wires are rerouted in the CPU power connector itself and its keyed on the motherboard side. Fundamentally, its the same voltage +12v so it shouldn't matter , as long as pins 5-8 are +12v on the EPS connector and pins 1-3 are +12v on the PCIe connector. Researching your PSU, the CPU and PCIe connections on the power supply are obviously keyed. Pins 3 and 5 are different.
See now if you don't overclock you don't have to buy a higher-end MB, and you can use the stock cooler, which comes with a thermal paste patch, and won't be too big. Overclocking may be pointless anyway if you are gaming and you are GPU limited. Overclocking is just a way of cheaping out anyway. Spend the extra money for a better processor up front. Make sure you buy and install memory to take advantage of the multi-channel RAM capabilities of your MB. If you've got dual/triple/quad channel, buy that many sticks, and install them in the right slots to take advantage of it. Be sure to consult the MB documentation to figure what will work with your MB/CPU combo. (I facepalm every time I spec out a Dell computer for someone at work and the default option happens to be a single stick of RAM. WTH, Dell?) Also I concur with Svetoslav. If you aren't going to put in the max amount of RAM your MB/CPU supports, try and leave some slots free. I also have to put in a word about CPU selection. If the computer is not going to be used for intensive stuff like the latest 3D gaming or video editing, it is more important to find a processor which higher single-core performance, than overall performance. It is always a good a idea to make sure the processor you buy has good single-core performance anyway because you won't always be doing intensive tasks. Passmark has a great CPU benchmark database which I reference frequently.
I have an idea for a awesome build. Let's call it the TV stand All in one Gamer media center. So first Buy a small or even large entertainment center or TV stand. Modify it to mount all components of an awesome gaming rig and media center. Kinda like the desk PC you built. But this will be better. Asus has a ROG 65" monitor. You will need that as well. I would go ROG for the whole build. Add controllers and remotes to operate PC and don't forget the Addressable RGB. Yeah!
Don't forget to put the side panel off if u, have a toddler living with u(my small brother who was a toddler took the screw driver from my table and start shoving it into my motherboard destroying the printed circuits and ripping the graphics card out of its slot and destroying the pcie slot by taking the single head out of the screw driver and pulling it out by force and I know this cus I saw everything on my cctv in my room and now I only have a laptop with gen 8 i3 and 8 gigs of ram and on board graphics and u will say what happened to the processor well I dropped it while taking it out and bended some pins and snapped some right off the processor)
Only thing I would really say is to learn as much as you can before doing anything. I've been building computers for 15 years now and here I am watching a beginners video (along with the other experienced commenters here). You never know where you may learn something. And with computers the learning never ends.
i have an asus z170-a mobo and i didnt put the io shield in, i tried for about 15 minutes but it just wouldnt go in with it intsalled so i took it out. Is there anything wrong with that? i have the pack of the pc facing the wall so i cant see it.
Whether you are using air or water cooling, leaving the IO shield off means there is a gaping hole for dust to get inside the case very easily. If you are relying on air cooling then it can mess with the positive/negative pressure of the case although it wont effect it that much. It's mostly just an issue of dust getting in.
Probably not a big deal, but if you also have your case fans set up with more exhaust than intakes, you would have negative air pressure and dust would get sucked in through that opening.
for earlier builders, make sure you pay close attention to cable management. might not seem like a huge deal but trust me, if you have to go back and upgrade something with a case full of random PSU wires, it can take way longer than necessary...
I actually hate that you use the notification pop noise.. I watch these videos in the background while I work and I keep thinking someone is chatting me..
Tip: When buying, get a warranty for products of primary concern (CPU, GPU, Motherboard, RAM, M.2 Drive, etc.) and buy NEW for said products on a priority basis. If your product has a manufacturing error, you may not notice the issue immediately or the issue may be gradual. Getting a two year warranty will help with this issue, but the issue then becomes cost. In which case, narrow your priority products down and ensure that at least some of the most important parts of your build are dealt with and well protected. I say this from personal experience. 😅
chewbaca wookie I forgot it first, too. I took my Mobo and stuff out and put it back in, but it was annoying. My case uses little dimple like things instead of actual standoffs, and it was a pain to screw the board in for me as a first time builder that way.
slipknotboy555 Yeah I just didn't understand how it went in, I thought I could do it after everything was already inside the case but what ever it doesn't seem to be that bad. Its extra ventilation.
My friend got a 1050 ti and he was telling me that he didn't feel any performance boost.
I went to check and i found out that he plugged his hdmi to the motherboard the whole time.
He kept using the integrated graphics for more that 6 months
Mystery Man lmao intergrated cpu power!!
LOL
Lmao
A Human someone on Newegg or the comments (pretty sure the comments on another video) said the same thing (maybe for a year) he had like 14 fps
Brainiax260 isn't that optimum?
speed > 0.5 - really drunk linus
speed > normal - sleepy linus
speed > 1.25 - regular linus
Eddynstain lmao
Lol
what how come 1.25 sounds regular
05 speed is king haha
Your so right
this is the chillest Linus i've ever heard
I prefer this Linus
Yeh this Linus is so chill
Sound just like a teacher explaining something to a little kid.
Yup very true
This show that Linus really loves to inform people very well 😊
plug your monitor in to the gpu, not the mobo
M1das depends
Depends? I'd say if you bought a GPU u would like to use it, right?
This is big. First time PC builders often don't know that there's a difference and end up with a black screen.
This is a mistake I made building my first PC, I thought I might've messed up the entire build until I plugged in the HDMI cable to the GPU.
Qbriosa that makes no sense what so ever what the fuck
Do NOT install Windows/Windows Updates or flash your BIOS during a thunderstorm.
lmao
mclightning88 haha true
Don't install any windows updates on a laptop if you have an Nvidia gpu! without making sure to update the drivers immediately after anyway.
Unless you have a UPS/a death wish XD
Do not keep your computer plugged in during a thunderstorm unless you have some king of high grade lightning protection... (battery power completely disconnected might be the only 100% safe way).
late af comment but - especially for first time builders, make sure to take your sweet time building everything, not just to enjoy it, but to make sure nothing goes wrong, triple check everything - my first build took 2-2.5 hours, but with the caution i took i had a successful boot on the first power up, and a month in still no issues
Ill remember that
2.5 hours? My first build took 6 hours, and that doesn't include the time used for research and tutorials like this video.
Definitely! Take a few extra minutes to do it right the first time. One small detail can cost you far more of time later.
Already built a FX-8350 rig, and am currently with a R5 3600x right now.
No problems whatsoever 👌
when i was as reading i thought you said 2-2.5 days... thats probbaly just me
*Tip #1* - Run the EPS 12v Power cable for the CPU (4xPin / 8xPin) before installing the motherboard. Some smaller cases like the Corsair Spec-02 don't have enough room to run the 12v CPU power through the cutout on the back of the motherboard-tray once the board is installed. Running this cable before installing the board will ensure you don't have to run the cable across the front of your board.
*Tip #2* - Lay your computer on it's side when installing the GPU, don't install/remove it while the chassis is standing up. This will help keep your GPU straight and limit GPU-Sag at the start. Some GPU will sag regardless due to the weight however some that would install straight will otherwise often have a little sag if installed vertically.
*Tip #3* - Pre-bend your cables. If you need to put a bend in a cable to route it be sure to pre-bend it before connecting it to the header. You'd be surprised how many USB3.0 and SATA connections have been brought-in due to new-builders breaking them off.
*Tip #4* - Cable manage your 24-Pin motherboard power cable first. This one can be subjective however I find that it's much easier to tie-down this large cable first and zip-tie other cables along the side of it. This helps especially when back-panel space is a limited luxury and gives you something to anchor to when manufacturers don't provide adequate tie-down locations.
*Tip #5* - Maintain constant pressure when mounting LEDs that use adhesive. Of course everyone knows that having a clean surface is necessary for a good bond, it's also beneficial to hold them in-place for at least a minute to ensure the adhesive bonds well. This also helps squeeze out trapped air that may have been caught in between the LED source and the chassis.
*Tip #6* - Do NOT over-tighten your CPU cooler. Previous generations Intel CPU's (Haswell 4th Gen and below) didn't really have an issue; However since Skylake 6th Gen CPUs, the substrate (PCB layer) is much thinner and is susceptible to being bent under pressure. I've only had a few PC's brought to me with this issue but it does happen. Needless to say the pins on the socket underneath were bent too. If the mounting hardware uses thumbscrews I only hand-tighten however is using a cooler that requires a screw-driver pay close attention to the force being applied. Some coolers have a "safety-stop" that prevents over-tightening but many do not.
*Tip #7* - Use your PSU as a ground. Many don't have an anti-static workstation or a place to connect a grounding wrist-strap. However if you plug you PSU into the wall (make sure the switch is off/0) you can touch the PSU to discharge yourself or mount the grounding strap to the fan grill/honeycomb exhaust holes.
*Tip #8* - POST test your components outside your chassis before installation. Almost nothing is more frustrating then completing your build and putting a ton of effort into your cable-management only to have your new rig fail to POST. You can use your motherboard box as a test bench and connect your components to ensure everything works before installing.
*Tip #9* - Record yourself breaking the the seal, opening the box and examining the CPU Socket pins on the motherboard if ordered online or check the pins before you leave the store if bought locally. This is to help protect yourself and hopefully assist in the event of a return/exchange. All retailers essentially have a NO BENT PINS policy, "Pins are bent? You want to exchange? Pft SAD DAY FOR YOU!" This is understandable in the sense that it's, for all intents and purposes minus limited caveats, impossible for bad to arrive at the retailer with bent pins and you will be stuck with a nice paperweight unless you have good eyes and a steady hand. If your eyesight isn't the best or you have difficulty discerning all of the pins, use your smartphone to take a high-resolution photo so you can zoom-in on the picture taken for a much better view.
*Tip #10* - Mount your fans for your radiator in a "Pull Configuration" if you use it at an exhaust and live in a dusty or furry environment. This will make it far easier to clean when dust/fur collects in/on the fins. Don't worry, whether in push or pull you don't have to be concerned about higher temps.
*Tip #11* - Using an AIO Liquid cooler and not overclocking? Then show your GPU some love! I do alot of builds where people want liquid coolers on locked (non-K) CPUs and have awesome GPUs. Sometimes they specifically ask that the radiator and fans intake fresh air for lower temps; However this isn't the best option in most situations. A non-overclocked CPU will not benefit from slightly cooler temps but your GPU can/will. With GPU boost/overclocking one of your first ceilings will be the GPU's temperature. The lower your GPU temp, the more headroom your card has to run faster. (provided you're not hitting a power limit)
*Tip #12* - Make sure when installing Windows 8/8.1/10 that your UEFI is set with "CSM"/Legacy Support/"Windows 7 support" turned off and that "Windows 8/10" is selected if applicable and not "Other". If your options include "Windows 8/10" AND "Windows 8/10 WHQL" select the prior. This will ensure that all four partitions are created and that all of the Recovery Options are available. If legacy support is enabled you will lose out on some features like "Reset your PC" and "Refresh your PC" without an install/recovery media.
*Tip #13* - Unplug all other HDD's or SSD's besides the target drive for the OS. Windows likes to install the Boot-loader on a different drive rather then the target OS drive. This will help prevent headaches and downtime in the event that the drive Windows installed it on is removed or fails. Just reinstalled the OS on a SSD a few days ago in which the storage HDD died and the OS didn't have it's boot-loader. Of-course there are ways to correct this but I also wanted to disable the legacy support in the UEFI as he was also missing many of his recovery options.
*Tip #14* - I need a new GPU. No seriously my GTX 780 is showing its age. :( Will update post with more tips when I'm not as tired, I know I'm skipping much more helpful info...
I pretty much did exactly the first one there, only with the spec 03. It looks like Corsair didn't test that in the factory.
Aiml3ss Calam1ty tip #15 for you. buy parts on discount or black friday. Less cost for each part turns into better parts and a better overall computer for you.
I feel like grounding yourself against the case would be a better idea, but if it's been working, then you go.
Aiml3ss Calam1ty is #12 like when you hold down a button on the motherboard screen while booting ?
Aiml3ss Calam1ty Thanks a lot!
1 - Be gentle with the HDD. It doesn't take a lot to kill one.
2 - if the GPU isn't going in/out, don't try to force it in. You will break the PCIe slot.
3 - if the PSU cable can't quite reach, don't try to stretch it as that may bend the pins/connector and cause damage over time even to the cable if it's a lower grade one.
4 - avoid cases without a bottom intake for the PSU. A cool-running PSU lives longer and has increased stability in some cases.
5 - The Intel stock cooler is enough for most CPUs - only invest in an AM cooler if you want a quieter solution or temps are going over 70*C
6 - Balance your build. If gaming, don't buy an i7 and a 1050/460 combo or an i3 and a 1070 combo. In both cases, you'll be better off with an i5 and 1060/480.
7 - Leave yourself RAM slots for future upgrades. What may seem like enough now may not be enough in the near future (I recently found this out after using 40 tabs in Firefox and using 6/8GB just doing that)
lol why are you using 40 tabs? Don't you ever shut down your computer?
I do - I actually use all 40 at the same time. It's a first for me.
Those are some mad multitasking skills... you might even be able to get a world record!
a bottom intake for a PSU is good if you have you case on a desk, then the air going through the PSU is cooler then pulling from the case, and will be even better for loggevity. Plus any case with a bottom PSU intake can be ignored, because you can still mount the PSU to pull from in the case.
No? It's quite simple - I have about 10 articles open and several tabs with resources and resources monitors. Linus uses about 60 IIRC.
Don't get your tongue caught in the CPU retention arm...
An extremely common problem
If you're black.
Instructions unclear!
PC is now pregnant!
Rusty Shackleford excuse me?
@ALI Aliraqi woah black is racist now?
You don't need a GTX 1080 for league of legends. The overflow of enthusiasm is a big trap.
whatever scrub I run league at 4K 300 FPS on triple monitors
You're so right that's why i went with the GTX 1070
NovemberBegin lol on 3 screens is cancer on unlocked camera imo
Every PC deserves at least the best card you can afford. What, do you hate your computer? You don't want it to be happy?
5erazoR Ik my friend told me he was gonna get a 1080 to play league.. ffs man
never overtighten screws.
I'm 99% sure I stripped a few screws in my PC and 99% sure that I will hate myself in a few years when I want to replace something.
If I can't afford a motherboard, can I use a cutting board?
You should probably use a fatherboard actually, you can't download as much ram to one like a motherboard can but you'll still get decent rpm.
You might need extra knife slots.
Make the cutting board marry your father
if it has a cpu and pcie slot then yes
@@linkthehero1234 haha haha WOOosh
I got a GTX 1060 but it was 5mm too long for my case, so I just bent a bit of the case and everything worked out.
BRUH
just take off the fancy shroud
You’re on a government watch list for that one...
A reasonable outcome.
I used side cutters. Lol
Anyone notice that Linus pronounces Z as both "zed" and "Zee" in this video
ye lmao
He used tunnel bear to research for the script and it took him to the USA.
@@MJRaymond from Vancouver, can confirm. When I lived further north, it was VERY strongly just Zed. Since moving here even I've found myself saying Zee occasionally
He's a confused Canadian
At first I thought he was saying words to make sure nobody misheard him but then he said y...and b,h,c lol
When building or upgrading, I like to always lay out the components in order of install.
I used to make a list, but by having everything laid out (first closest) it helps me to foresee any missing components, oddities or needed mods.
my tip is to not drop your new gpu that your releasing for the first time
my friend did that with his 980ti strix when he first got it
LinusGPUDroppingTips
lol
Thank you
Raj is going the kick the shit out of you
I once assembles an entire PC inside my case, and things didn't fit QUITE right. I tried booting, and nothing happened. I was soooo confused and looked up the motherboard model and problems with it and detailed troubleshooting guides, but nothing worked.
THEN I found out what motherboard mounting screws are for. Once my entire board was NOT short circuiting on the steel case, all worked like a charm :P
You are lucky it worked at all after that!
Same here. I never heard of the things despite a lot of reading up and following the manual. When I did try to install them, they just wouldn't fit at all. At best, they'd get stuck sideways. I hammered them through the metal and it was a huge ordeal. To be fair, only the PSU, case and RAM were new, the rest were old used parts, because I was impatient for the real stuff to arrive and I wanted to practice to avoid mistakes. So I wasn't all that diligent.
And the stuff still worked. Maybe it's the expensive PSU.
Still had problems with those dividers on my second build. Hate those things.
I did this with my first build, and I had a CHEAP (like, $40) motherboard! It surprisingly held up, after I had called my brother who was already into the building computers thing. That motherboard has since been sitting on carpet, used on carpet, and tossed around more than it should've been. Now it is my spare pc-in-a-box, for when my system gives out, due to it being a xeon X5660 (equal to i7 980x) at 4.7GHz and 1.4 volts, matching almost exactly the performance of a non-overclocked i7 6800k.
Was called as an SOS from a friend who was building his first pc, came over and looked at his motherboard. Left half on standoffs, right half touching the case. Luckily he didn't get far enough to turn it on before I got there
Always remember to instal 2 floppy drives, so that you can leave the OS in one drive and use the other, without the need to keep swapping the discs whenever you use a disc command. (such as dir)
Floppy?
Floppy????
Im konfusion
@Jacob Elizondo
LOL, YOU SHOULD REALLY CONSIDER UPDATING.
Is ThIs a JoKe
make sure to discharge static safely.
How is that achieved?
frequently make sure to touch metal.
SangoProductions213 statox doesnt really matter that much unless you're talking about the CPU
Wrong (Donald Trump innuendo), "statox," or the correct way to spell it, static, does matter. Static discharge can ruin any component of the computer, which is why you must touch metal, preferably the case for certain reasons, in order to ground yourself.
Exactly. Bricked a 200 dollar graphics card by being careless. And this is coming from someone who has basically $0 annual income.
Don't let the cat piss on your motherboard... Past experience
Same happened to me but most of it went under it not on top but it killed a Soundblaster X-fi...
Wait, what happen4s to your keybv4oard if you d4o? I'm asking fo4r no part4icular reaso4n.v
Would that b4y any chanc4e cause shortcuts and therefore44 random letvters or number4s to appear, as well as cause4 keys to get st4ucvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv4444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444
4
Voult Bioy piss cat?
wait, how does the motherboard affect a keyboard?
Linus: "Countless builders did ..."
What he actually means "I did countless times ..."
put in dust filters
always
_Sitzkrieg Any recommendations?
I buy the single fan filters off ebay. They are pre-cut and just attach at the screw holes
@@colossalbreacker How choose
dust filters and a aluminum mesh screen do wonders to keep out HAIR, dust, and BUGS dear god all the bugs that can somehow fit SO deeply in these electronics is terrifying.
Top tip. Don't spread thermal compound, it's a liquid and the pressure of the cooler will get it far smoother than you'll ever be able to.
Not all pastes are liquids. And spreading is actually neater than the dot, because the don't won't cover the whole IHS.
Who cares if its neater, you are not gonna look at it. And even if it doesn't cover the whole ihs its not a problem because the CPU die is in the center where a dot of thermal paste would easily cover it.
You are supposed to use a very thin layer.
I spread just enough to cover the CPU case. I really should wear gloves doing that (it is labelled as toxic (will kill you over time, not immediately)).
Thermal compound is meant to cover up pockets of air between the heatsink and CPU, as long as everything that needs to be cooled like cores is covered up it's good to go
When you spread you trap air bubbles. With line or dot, as the paste spreads it forces all air out. It is physically impossible for it to bubble. As for having to cover the whole ihs... You dont... Just the central bit. Wonderful thing about heat, it conducts through metal...
Don't build PC's while you're drunk
Is this a throw at Kyle from Bitwit?
But, I always do that?!
You mean the GPU doesn’t go into the DIMM slots?
@@jem4838 The header pins should never go down on the USB controllers. Or should they.
Hold my beer
Please mention cable management in a future installment....the biggest bane of a PC builders existence
Not so bad, the trick is to do the cables first, then put everything else inside the case.
The problem is when you put all the parts inside first then connect the cables to the component, you'll then try to hide the cables in whatever space you find.
Count yourself lucky that IDE ribbon cable origami isn't a thing anymore
Marc Charbonneau Fair enough. I've only gotten into PC building in the last couple years or so. Arrogantly I decided to choose the Prodigy M for my first build thinking "Honestly how hard could it possibly be?" After about a week of cursing and swearing (that case was a damned nightmare) I gave up in defeat and decided to go with the Arc Mini R2 instead.
Yep, made the same mistake and ended up paying someone to do it for me. Handsome case though.
having bad cable management wont really cause you any performance problems. they have already done a video about this (maybe on LTT) where they jam as many cables as they possibly could into the case and it does practically nothing, so, unless your cooling solution is so bad that your PC could burst into flames at any point, having a few extra cables running through the case will do fuck all.
One thing I learned a while back is to add things to the motherboard before putting it in the case, cpu, memory & m.2 drives in particular
Makes installation a lot easier
I thought this is common sense lol
@ kinda is yea
My tip is to check the mobo's memory compatibility table and buy accordingly.
SchoolTerrorist your computer probably won’t even boot up. You can go under the RAM compatibility numbers but not over. Check your mobo website
What happens when you have top of the line mobo and cpu and the list only shows max 32gb but you decide to go 64gb lol
best pc building tip, "Don't half ass it".
Don't cheap out on certain parts, and Spend a little time planning out the cable management.
Also my biggest downfall, DONT FORGET TO SEND IN THE MAIL-IN-REBATES!
I think beginners tend to be tempted to go cheap on the PSU and motherboard because they don't see tests and benchmarks demonstrating performance boosts. I tell people if they are going to overspend and go overboard anywhere, it should be for a good PSU and motherboard. You'll get many more frames if your PC doesn't short out and fry your expensive new components.
AKSBSU is a b350m pro vd plus a good mobo? Or did I cheap out too much
I'm not familiar with that particular board, but I've had only good experiences with MSi motherboards so far. I personally tend to go with a higher priced board, but it will probably be OK if it has all the features you need and runs your RAM at a decent speed. I was talking more about avoiding off-brand junk like PSUs from companies I've never heard off that exaggerate specs and burn out in a few months. MSi has a very strong reputation for mobos. I've actually only bought MSi boards for the past decade. I look at other brands like ASUS and Gigabyte, but I ended up getting great deals on the MSi boards with recent builds.
AKSBSU ok thx for your input
I'm glad this video didn't contain anything I didn't already know, was worried I might've missed something in my 6+ months of build prep lol.
I forgot about the IO shield when I was building mine so I never put it back. I might make a cardboard one.
Just Myself be
+PolitikZ I'm a spiritual lyrical PC building individual.
Make sure your motherboard supports 7th gen without a bios update or you'll need another cpu just to get the new 1 working =S
Jason Wilson Good one, happened to a friend of mine. He had to borrow my i5 to update the bios. For I7 compatibility.
Learned that the somewhat hard way with my r5 2400g
Or has bios flashback. No cpu required to update.
happened to my friend too, luckily he was just upgrading cpu's and could use the old one to update it lol. but he was really puzzled on why the monitor wasn't displaying when he tried to use the i7
dont forget to include windows price when building a new pc.
I didn't forget... Linux, bitch! :p
sienile Linux for life
Not everyone is going to use windows.
hell no, its not worth $100, just pirate it or find a cheap activation key
Meh, pick it up cheap on kinguin or related sites
Case and motherboard manufacturers should really come up with some standard for those front panel connectors and IO shields.
I don't install those IO shields anymore, not worth the risk of damaging the motherboard.
@@hakont.4960 congrats u won the idiot award 2019
@@ih7168 Why am I an idiot?
@@hakont.4960 do you even know why IO shields exist?
@@zackaryrethati7627 Enlighten me, my PC seems to work fine without one?
Back in 2014 I tried to build a PC for a friend. Not only did I mess with the front panel connectors, but also forgot to put the I/O shield, which I then forced in so I ended cutting my finger and had a couple of blood droplets falling onto the motherboard. Eventually, everything worked, but what a monumental sequence of blunders it was.
The worst thing i saw so far when i was working in a PC shop was a guy that put in the motherboard without the placeholders in place (aka screwed directly to the case). Not sure if this is common for new pc builders, but it was for sure a sight to behold. :D
zomfgroflmao1337 yep, we did that on my friend's pc, we saw those placeholders but we had no clue what they did so we ignored them xD
He should have used a "my first PC case" made of plastic.
Seriously?! How stupid can people be... "Oh, I'll just bolt this motherboard with all these component pin tips sticking out of the back directly to this metal plate. Nothing will short out." Anyone that dumb should never touch the inside of a PC case.
Steven Box I guess they're not pre-installed as different ones fit different motherboards, and that would add complexity and expense to making cases.
+sienile we ve never heard of them or seen them since they are under the motherboard, and our prior knowledge was changing graphics cards and ram
AMD being completely skipped on the overclocking part xD
MaxArceus Yeah, maybe AMD should have paid for Linus & Co to attend CES...
They did, check some of their CES videos on the Linus Tech Tips channel. A few of them are sponsored by AMD.
That was obvious sarcasm.
It's a joke.
Well, nobody wants to start a fire in the house.
Here are some issue I ran into with my first PC build:
1.) forgot to plug in the system speaker so no beep codes when the following happened
2.) ram was in the wrong spot. needed to go in slot 4 and not slot 1
3.) PSU had significant wattage but I misread the connector types and it didn't have enough PCIE 6+2 cables to power my GPU.
4.) make sure your processor has onboard graphics before you try and use the inboard port while breadboxing. couldn't get system to post without using my GPU and got confused until I realized the difference between APU and CPU.
number 4 got me
awkward gaping hole?
i say better airflow
ryan xie hehe
trap. dont forget wifi adapters or ethernet cables
I just finished my first build, my only problem that I wish I knew before hand was which way my cpu cooling fan should be facing.
Tip: Just because two different sockets have similar names, doesn't mean they will work together. Example: LGA 2011-3 CPU on a 2011 MoBo or FM2+ CPU on an FM2 MoBo.
Some guy on the internet another example for this is that a previous gen skylake 1151 boards will not necessarily natively support the new kabylake without a bios update. so if you don't have a spare chip around you'll have a non funtionctional pc
+Dillon Lin yep always check the bios notes before buying your board. Same is true on X99 boards too.
+Dillon Lin Is it dangerous to make a bios update? I mean, I just bought a 1151 mobo but I was planning to return my skylake for a kaby lake ...I know I have to make a bios update to make it work, but is it dangerous?
Angelo Julioth Use the Skylake chip to update the UEFI/BIOS, then put the Kaby Lake chip in. And no, it's not dangerous. You can find many tutorials for your specific MoBo online.
Alright, I get it, so ...if my mobo doesn't come with the feature to update bios without CPU, It would be impossible to update bios and I would not be able to use the Kaby Lake one, so I should get the Skylake one at least to update bios. Thanks!
buying an expensive mobo for "features I might use"
hitesh jetwani I just bought my motherboard because it was the coolest looking one that I can afford.
Please say that you have even a window and enough lighting for it to be seen...
I can't tell are you advising for or against this. Personally, I think 'features I might use' would be a really good thing to consider, as probably the majority of upgradability is tied into what your motherboard supports, and otherwise, you need to replace said motherboard if you really do want these features later.
Ei'riġ Proinsias Dammantaċ Ó Gaṁna lol I cheaped out on my mobo and I got a b350m pro vid which supports 32gb of ram (2 channels and I got 1stick of 8gb so whatever) and it’s pretty limited
I bought an LED mobo and an opaque case =_= realized tooo late
For a first time builder, is wiping off the Intel stock thermal paste and replacing it with another higher performing paste ok?
Yea its fine.
yeah its a bit better, use rubbing alcohol to make it ez n cleen
Actually, I would recommend it. 99% of the time the manufacturer is using something that will work, but not as good as some 3rd party thermal pastes that are out there. I use Arctic Silver most of the time. It works great and is inexpensive. Make sure the base of your CPU radiator or pump are cleaned well to remove the stock paste. A small amount of rubbing alcohol on a clean rag works well.
Yes you can but id say it's a waste of thermal paste, the cooler is not the best and changing the paste will probably just make it drop a few degrees tops if even that.
Yeah, and it should actually be better for your temperatures than the bird shit they spread on.
*PLEASE KEEP MAKING THESE VIDEOS, AND SIMILAR BUILD TIPS VIDEOS!!!* Thank you kindly, and be well!
As much as I don't much need these videos (Since I am pretty well versed in everything you can possibly bork, after ~25yrs of porkchop build errors), they are GREAT for sending new builders to so that neither do I have to be there for their build, but additionally I prefer to teach people to look things up for themselves, as opposed to just doing it for them, or just telling them what to do...
My tip is to plug the psu in
Harvey jam and make sure the switch is on
lol
Make sure it's snugly inside. So a slight tap to the wire won't disconnect it...
Happened to... A friend.
RpiesSPIES This actually just happened to me recently
every time i forget to plug the psu in and then im sat there for an hour wondering whats wrong
Ohhh I once discovered I'd had the plastic film still on the bottom of the heatsink for YEARS. But never had problems with it though. Kudos to both Intel and Zalman I guess ':)
I hate IO shields. They are annoying
you can say that. Have forgotten them more then once, and one time I was proud of myself for putting it in before the mobo, only to later realize I put it in the wrong way... Then comes the fun task of getting it out without bending or breaking it...
Fun for the family for all ages.
Billy Ashworth I didn't even put mine on
I don't understand why Motherboard manufacturers don't make the IO shield be part of the board. I think it was one of Linus's videos on the ongoing CES that showed a motherboard that came with a built-in IO shield, and all I could think of after seeing that was "why haven't they changed this to be the default for every brand?!"
TwilightWolf032 I agree! With the cutout for the I/o shield being standardized (at least, I'm pretty sure), I don't know why more companies don't make it part of the board. I'm sure it adds more cost than the cheap separate ones common now, but probably not by all that much.
Asus ROG MAXIMUS IX FORMULA
www.asus.com/ca-en/Motherboards/ROG-MAXIMUS-IX-FORMULA/
Some things that have come up in my life as a certified computer repair technician (there's a lot of them):
- Assemble base components before installing into case (if you have bad ram, video, MB, or proc).
- Check graphics card clearances relative to the case as well. (Long card, short case)
- Check fans / airflow.
- Put thermal compound between CPU and heatsink.
- Check that you have thermal compound, not thermal paste (this actually did happen to another employee).
- Check amount of power supply connectors and length of power supply cables (this has happened to my backup machine).
- Unless you plan on running Linux, you need to shell out cash for Windows.
- Make sure you're grounded (cold weather means dry atmosphere, and dry atmosphere leads to static shocks).
- You have hard drive storage, do you need a disc drive? Does your case have a disc drive bay? (This has happened, a lot)
- If you're shelling this much money out for the computer, go the extra step and get a Blu-Ray drive! Combo, at least.
- Do you need speakers?
- Do you have a keyboard and mouse?
- Does your case have front USB ports? Does your motherboard support these ports? (USB3 ports when board only has USB2)
- Does your motherboard have enough fan ports?
- Do you have external cards? Can they fit in the motherboard slots? (PCI / PCIe)
- Do you have the right memory? (This has tripped me up as DDR4 was hitting the market)
- Are those standoff screws already installed? Do they align with the motherboard you're installing? (MicroATX)
- Secure the motherboard with all the screw holes.
- No, those PC components won't fit in that Mac case...
- No, those Mac components won't fit in that PC case...
- Don't skimp on the processor. Intel Celeron/Pentium and AMD E just don't cut it.
- For today's standards, get more than 4GB of memory if you can afford it.
- Unless you're concerned about power consumption, don't use Green drives. (Don't use Purple / Video Surveilance drives either)
- You don't need to hide the wires, but it helps.
- Also check case width when using that large heatsink.
- CPU fan goes in CPU_FAN on the board, not SYS_FAN, not CPU_OPT.
- Microsoft Office will need to be registered with a Microsoft account.
- You need antivirus. Only one. 2+ and you'll crawl slower than a turtle.
- Add-on video card? Plug it in there, not to the motherboard.
- Plug the power supply in with a satisfying 'click'. Brace the board if the board is too long.
What is the difference between thermal compound and thermal paste?
I know that you should avoid thermal glue... ;)
www.pcgamer.com/whats-the-difference-between-thermal-paste-grease-and-pads/
You are actually quite helpful, Linus. Bought an already built PC recently, but I was just messing around and I took out all the front panel connectors. Searched a lot how to plug them back properly but couldn't find all the information I wanted. You cleared it up in under 30 seconds.
Don't forget to push your PCI tab down before removing your graphics card
:'(
Building traps to avoid: First, install the right size power supply. Not having enough wattage will cause power surges, which could lead to system failure. And, if you're going to use a internal hard drive to backup your computer, make sure it's not a storage drive. That is to say, make sure the drive is bootable. If it is not bootable, then it will lead to you having more problems and spending more money.
Use masking tape on nice finishes when setting the case on one side! Touch up the inside with touch up paint (brush) if the inside finish gets chipped when screwing and installing drives. Moisture can seep into the case and prematurely corrode especially around fan vents. Coolmaster case I ditched had much rust in the front grill, second one I received, I took off all the plastics and left just the metal to cold galvanized primer then spray paint the color back and over 10 years later, not a lick of rust! The last case lasted less than five years. I've multiple systems and found with case screws and screws in general, 3 in 1 Oil the threads, tighten then back out a a less than a quarter turn. Two things it does: protects the threaded metal parts and easier to untighten at a later date.
You can tell CES is going on. Every tech TH-camr uploads shit videos while CES is going on.
This was actually a pretty interesting topic.
You can also tell because they are making videos about CES....
The videos are shit because the products presented are shit.
this video is obviously for less experienced builders. it's not shit just because it's not useful info to *you*, there's alot of people watching this channel you know?
krelsen7 I came from reading other's stories on forums years back for my first build during the Nvidia 8800GTS 320mb GPU days and found out GPU is literally EVERYTHING. It took my my 4th GPU for a solid one where I can comfortably jam any game for the next several years to come. I currently use the R9-390 8gb GPU
the way he explain makes you feel like you are an 8 yo kid.
To be honest, that is the target audience.
we are speaking about building a PC not a sand castle.
to be fair, building a pc is easier than making a sand castle.
He probably looked at the comments on his videos and assumed only 8 yo kids watched his stuff
because there are too many 8 yo kids making minecraft tutorials
Some thing that has really worked out for me and alot of people do it the other way around;
After installing your motherboard (with ram, cpu installed) do your cable management and kabels before anything else. When everything is installed you will have a hardtime plugin everything in. Make it nice and clean before installing any other component after your motherboard is set. After all cables are ready and plugged and managed than hook up your graphics card, cooler, harddisks, and powersupply, Make sure you leave some space and are able to move your cables a little and that not everything is super tight. Goodluck building.
Make sure the gpu you buy can fit the case if you buy the gpu that can't fit your case you are scrued then you need to buy a new bigger case for example you have a micro ATX case and you buy an gtx 1080 that could probably not fit so take a look on that
There are gtx 1080 made for mini itx
I was so excited when building my current PC I forgot to plug the power to the gpu and spent an hour trying to figure out why I wasn't getting any sort of display xD
dude, you speak so nicely that it's really easy to understand every word that you are talking. thank you very much for the videos! :)
i think a great episode will be about M.2 and U.2 and how to take advantage of those things in your mobo. btw great video Linus !
Once, I found an OEM pc with the "remove this first" plastic on the cooler
A pc trap i would avoid that might not be so apparent is impatience. You finally have all your parts and youre excited. Youve watched a million build guides, you know exactly what to do and you just want to put it all together as quickly as possible and start using it. It seems like it goes without saying, but dont rush your build. tried to rush my 2nd build, forgot to install the back plate for my air cooler and created a bunch of avoidable problems.
dont ever ever buy a cheap power supply. I got the hx1000i in platinum efficency, and my build uses between 1/3 and 1/2 of its capacity, which is fine. I spend very much money on the supply, but it was worth it. A friend used a cheap one on 3/4 capacity and had following problem:
the supply had enough over all wattage, but ad he installed 4 graphic cards, his use on 12V was much higher than the use of the other voltages. as he powered everything up, he suffered from the pc spontanously being powerless when loading a big game, and this damaged the cheap supply so that the 3,3V raised to 3,5V and that burned his motherboard and other components. remember me buying an expensive power supply? well my friend saved 250€ by buing a cheap one.. but now he completely destroyed 1200€ Hardware.
similarly avoid the cheapest motherboards
WATCH OUT FOR THE MOTHERBOARD STANDOFFS! If you have one in plus it may fry your motherboard. Trust me, I experienced it. There was one under the south bridge and it killed my PCI slots and my GPU as well. RIP MSI HD6850 😢
Bence Bokor do i have to take them off or what??
@@pianosenzanima1 when you Not need them yes
Your Board can touch one oft These like bence bokor says the harmles way it would fry your Motherboard or it would set the hole case under electricity load... ans this is dangerous.. and it can kill Not only pc parts ... i was toss throug the room and woke up at the hospital because i forgot One of These things under my board...
Sorry for my Bad englisch :-/
Linus I have to give you a kudos on your video compression abilities. I can watch all your videos at 1440 with no lag or skipping. I can't do that with any other tech vids.
my tip - make sure ram is actually pressed down and properly in the slot. sometimes it seems it is but isn't
I've ran into a couple times where a laptops sodimm somehow popped out and caused the laptop not to boot.
Adam Khan rofl I installed 2 extra Ram and my PC wouldn't boot. Eventually , monitor popped out with a message "overclocking error" so I went to BIOS on that single run to underclock everything. After that, the PC won't display any signals. It took me 10 minutes to figure out that one of the ram was a bit higher.I pressed it down and made a small "pop". Hallelujah!
i remember one time my PC wouldnt boot and for like 3-4 hours i was trying to figure out. reinsterted my cpu, checked all the cables. and then turned out to be the ram slot i felt so stupid since it was the last thing i expected
Is it me or is Linus making an effort to speak slower than usual?
first time builders top tips. only install one stick of ram for first boot (in correct slot refer to mobo guide). check all your component when built using memtest usb key, prime 95 etc. buy mobo with easy debug led, makes life a little easier when troubleshooting. ensure your bios supports your cpu. Do not buy more than you need, learn about chipsets and the different features they offer. use afterburner to monitor temps of built pc. invest in a good case. ensure your cables are tied and out of the way of components inside the case. plug monitor into the gpu not the mobo. to save money buy a cheaper (reliable brand mobo) as you can often make up for a lack of ports (sata etc.) with mini pcie adapters. And most important, Get 16gb of ram or at least one 8gb ram stick (so you can upgrade later without buying 2 new modules) if you plan to play AAA games. Also, the rx480 is a beast at 1080p.
yea if you made that video earlier i wouln't have bought a H series motherboard and could overclock my i7 6700k now... :(
Sorry to hear that, i was already planning to go out and buy the parts this week and i realized the gigabyte B360M doesn’t support OC, thank god Linus🙏🏻
I'm curious to know what happened to your board?
Avoid common PC building traps - buy a Mac
Koppa Dasao How can a Mac help me build a PC?
Koppa Dasao Macs Limit you like border control
Kaarel Kahu It's prebuilt
Hahaha, you're funny.
Koppa Dasao I dont see how thats relevant. Building a PC is exactly the process with or without a Mac.
TL;DR:
1) front panel connections: diagram on motherboard(MB)/manual shows polarity. pins: colored wire, or embossed arrow positive
2) air cooler: check CPU socket and case specs (might not fit in size wise) if it fits.
3) overclocking: need unlocked CPU (intel: k or x series), need MB with suitable chipset. (need chipset name with Z or X in it)
4) during assembly: put in I/O shield in case first and bend all needed tabs!
5) peel protective film on bottom of heat sink
I forgot to connect the CPU fan. The processor is overheating and I was hit with a heat sink. Processor survived. Intel Core 2 Quad Q6600.
I'm guessing the computer's owner was the one that beat you with a heatsink? You deserved it.
All modern CPUs have thermal protection so they throttle when they hit their max operating temp (usually 100 degrees) so it is safe to run it without a fan, it will of course throttle all the time and it is obviously not recommended to do this.
It was not until I started my adventure with the creation of the PC. Currently, even the wiring I have arranged, no longer commit such errors. I was much younger.
may i ask why you we're beat with a heatsink?
Lack of knowledge and experience
How about telling us how to avoid whatever it is Luke did in that Coolermaster case review / build video? No seriously though, tell us what happened so I can never do it! You can't just ignore an elephant in the room that big!
Good tips. Something that I do on a new build is add filter material on the fans and all open areas on the case. Dust and moisture is the second worst killer when it comes to PC's appart from heat and transient switching surges.
You forgot RAM speed for certain CPU and Motherboard.
you can avoid pc building traps if you just look at their adam's apple
anton rockoboac you ...
I like you.
Not if we keep it hidden. :^)
anton rockoboac lmao thanks I needed that.
I feel stupid for not getting it
Traps are a term for "advanced" cross dressers.
The cancerous things you learn on the internet.
Thank God I decided to go through these videos as I was falling asleep! I jolted awake about the size of the CPU cooler, checked the specs and realized it would have been 2mm too big! Planned on building it this weekend. Luckily I was able to get a quick order in to Amazon for the right size and cancel the other one before they shipped it out. 🤘😎👍
Install motherboard standoffs! I didn't on my first build and not only bricked the mobo, but there was even black burn marks where it shorted.
Something to avoid, when using SSDs which are mounted in the back of the case, look for power supply cables with no pieces sticking out (mine has this annoying plastic rectangle about one cm thick and I can't fit the back panel on... being the noob I am I tried to force it and now I am starting to pull the pins out of the cord, my solution right now is just no back panel
My tips:
-Don't cheap out on the power supply. Make sure to at least have a switch on it. Yes some PSU Don't have them.
-Don't buy a prebuild. And if you do, Just buy/get installed some pieces you don't feel comfortable handling yourself if you are a beginner. Buy the other paets at different price points anywhere online (well not anywhere but you know).
-Don't get mustard ketchup cables. There are plenty of pretty options.
-Add dust filters to your intake fans.
Do not plugging in the 8pin-PCIE connector (which is for GPUs) into the 8pin-EPS which is for CPU! I did that accidently :)
You cannot, its keyed.
Nidhogg84 That was also my thought, but on my PSU (a EVGA NEX750B) you could! It is a semi-modular PSU and you could plug it in the wrong plug on the PSU side ...
It may be plugged into the PCIe power connector area of the PSU. On my PSU: the Corsair AX860i, the area is designed 6+2 PCIE & 4+4 CPU. The wires are rerouted in the CPU power connector itself and its keyed on the motherboard side. Fundamentally, its the same voltage +12v so it shouldn't matter , as long as pins 5-8 are +12v on the EPS connector and pins 1-3 are +12v on the PCIe connector.
Researching your PSU, the CPU and PCIe connections on the power supply are obviously keyed. Pins 3 and 5 are different.
Nidhogg84: the polarity is reversed. So you are 24V from what the circuit expects.
The "Don't force stuff" adage may apply here.
Make sure you always rinse every component with light, soapy water to ensure they’re clean so data can transfer faster
Matthew Disliked, I tried this and when i turned on my pc, nothing came up.
See now if you don't overclock you don't have to buy a higher-end MB, and you can use the stock cooler, which comes with a thermal paste patch, and won't be too big. Overclocking may be pointless anyway if you are gaming and you are GPU limited.
Overclocking is just a way of cheaping out anyway. Spend the extra money for a better processor up front.
Make sure you buy and install memory to take advantage of the multi-channel RAM capabilities of your MB. If you've got dual/triple/quad channel, buy that many sticks, and install them in the right slots to take advantage of it. Be sure to consult the MB documentation to figure what will work with your MB/CPU combo.
(I facepalm every time I spec out a Dell computer for someone at work and the default option happens to be a single stick of RAM. WTH, Dell?)
Also I concur with Svetoslav. If you aren't going to put in the max amount of RAM your MB/CPU supports, try and leave some slots free.
I also have to put in a word about CPU selection. If the computer is not going to be used for intensive stuff like the latest 3D gaming or video editing, it is more important to find a processor which higher single-core performance, than overall performance. It is always a good a idea to make sure the processor you buy has good single-core performance anyway because you won't always be doing intensive tasks. Passmark has a great CPU benchmark database which I reference frequently.
Now I really want a porterhouse steak. Man that looked good.
TRAP: "dont forget to buy thermal paste"
Lots of coolers come with it though
except the one cooler you happened to pick out ;)
I have an idea for a awesome build. Let's call it the TV stand All in one Gamer media center. So first Buy a small or even large entertainment center or TV stand. Modify it to mount all components of an awesome gaming rig and media center. Kinda like the desk PC you built. But this will be better. Asus has a ROG 65" monitor. You will need that as well. I would go ROG for the whole build. Add controllers and remotes to operate PC and don't forget the Addressable RGB. Yeah!
2:22 anybody knows what is this motherboard?
PLEASE PLEASE check that you cpu is compatible with your motherboard. I just blindly bought a motherboard that said LGA---- and I got trouble with it
I wish linus was still this polite n humble in his videos
Expecting upgradability from a laptop ._.
Don't put your gpu in upside down, or put ur CPU in ur psu... but remover ALWAYS plug your ram into that pcie slot, and if it don't fit, make it fit
Don't forget to put the side panel off if u, have a toddler living with u(my small brother who was a toddler took the screw driver from my table and start shoving it into my motherboard destroying the printed circuits and ripping the graphics card out of its slot and destroying the pcie slot by taking the single head out of the screw driver and pulling it out by force and I know this cus I saw everything on my cctv in my room and now I only have a laptop with gen 8 i3 and 8 gigs of ram and on board graphics and u will say what happened to the processor well I dropped it while taking it out and bended some pins and snapped some right off the processor)
i have got a h81 cheap gigabyte mobo and it can overclock just fine
okay
that'd be the exception rather than the rule though, as Linus said in the video.
Yea, I overclock on my MSI H97, no problems.
what do you mean by "overclock"? Every motherboard can overclock, but not every motherboard can raise cpu multiplier past stock.
IIRC I run my 4690K at 4.2GHz, 1.2 voltage
Best way to avoid these problems:
Don't build a pc
JK, building is awesome
Buy console.
HAHAHAHAHAHAHAHAHAHAHAHAHA
Michael Mendieta lol
said no one ever.
Only thing I would really say is to learn as much as you can before doing anything. I've been building computers for 15 years now and here I am watching a beginners video (along with the other experienced commenters here). You never know where you may learn something. And with computers the learning never ends.
i have an asus z170-a mobo and i didnt put the io shield in, i tried for about 15 minutes but it just wouldnt go in with it intsalled so i took it out. Is there anything wrong with that? i have the pack of the pc facing the wall so i cant see it.
Quality Banana same here I built it in 2015 really no problem
Whether you are using air or water cooling, leaving the IO shield off means there is a gaping hole for dust to get inside the case very easily. If you are relying on air cooling then it can mess with the positive/negative pressure of the case although it wont effect it that much. It's mostly just an issue of dust getting in.
jhartles the z170-a has one of those cover things
Probably not a big deal, but if you also have your case fans set up with more exhaust than intakes, you would have negative air pressure and dust would get sucked in through that opening.
Quality Banana i have an asus z170a and the io sheild was ripping my hair so i said fuck it and threw it away
I wish I knew what half of this stuff meant
for earlier builders, make sure you pay close attention to cable management. might not seem like a huge deal but trust me, if you have to go back and upgrade something with a case full of random PSU wires, it can take way longer than necessary...
I actually hate that you use the notification pop noise.. I watch these videos in the background while I work and I keep thinking someone is chatting me..
When he said "if you want to overclock" at 2:50 my PC froze due to a not finished and completly stable overclock lol!!!!!!!!!!!!!!!
Tip:
When buying, get a warranty for products of primary concern (CPU, GPU, Motherboard, RAM, M.2 Drive, etc.) and buy NEW for said products on a priority basis.
If your product has a manufacturing error, you may not notice the issue immediately or the issue may be gradual. Getting a two year warranty will help with this issue, but the issue then becomes cost.
In which case, narrow your priority products down and ensure that at least some of the most important parts of your build are dealt with and well protected.
I say this from personal experience. 😅
I live with that gaping I/o Shield hole in my PC :(
chewbaca wookie I forgot it first, too. I took my Mobo and stuff out and put it back in, but it was annoying. My case uses little dimple like things instead of actual standoffs, and it was a pain to screw the board in for me as a first time builder that way.
slipknotboy555 Yeah I just didn't understand how it went in, I thought I could do it after everything was already inside the case but what ever it doesn't seem to be that bad. Its extra ventilation.