Rockford Fosgate R2-500X1 Amplifier Unboxing/Review
ฝัง
- เผยแพร่เมื่อ 26 มี.ค. 2021
- Instagram: Swishlife_
Business IG/Etsy: Killadesignhtx
Personal IG: _Kdontplay
Ebay: www.ebay.com/usr/swishlife
Music: Chuki Beats - ＥＵＲＯＳＴＡＲ - Aggressive Drill Type Beat 2021 (Prod. Chuki Beats)
• ＥＵＲＯＳＴＡＲ - Aggressive ... - ยานยนต์และพาหนะ
Love this Rockford Fosgate Amp! Got it running at 2 ohms pushing a single Kicker Gold Comp. 50th Anniversary 10” DVC4 doing work!#thePunch🥊#Kicker#Livin’Loud#🔊❤️
wer does my does my speaker wire + - go to run it at 2ohm
I got the same amp for my Rockford Fosgate P2 10 sub
Please help I have the 1200.1 version of your amp and I'm trying to figure our how to run 1 ohm is that how to do it the middle two terminals not the outside two?
Your speakers have to be wired to 1 ohm
I own this amp. It pushes 2 10 inch JL w3. Sounds pretty good, but I wish I went with a bit more power.
That’s what I’m running. Do you have the subs ran in parallel down to 2 ohms?
@@nickwooo1 I have since swapped out the amp for a jp8, a lot more power but I don't like the crossovers. The RF sounded a lot better. And yes I run the w3s at 2 ohm.
Was the amp itself wrapped in clear plastic? I didn’t see you take it off?
Mine was
My clean output goes red sometimes is that bad? Like blinks when bass hits does your aswell?
Is the auto over heat protect light .
It’s normal playing music
Were should I connect the wires going to the subwoofer. the sub is wired for 2 ohm
Next section of connection blocks to the right of where power connects to, says 2 ohm right on it.
@@SwishLifeGarage thanks
@@kamronyoung9010 no problem man you can also see it in the vid when I show the amp hooked up middle two block for the 2 ohm
@SwishLife Garage I'm running two 12s, does that mean I should be using all 4 ports or can I run it out of those two mid connections?
Soooo is this the r500x1d 2nd gen?
Exactly
Question for anyone who knows but i have 2 4ohms subs where do i plug it ? In a+ And a- ? Or b+ and b-?
Same question I have brother
I want to connect a p3d12 2omh subwoofer.
But I don't know on which of the 4 inputs to connect A+ A - B+ B- ?
@@jhonnygraciano5042 A- B+
How do I get my R2 500X1 out of protection mood was playing good then protection mood hit. It's still gets a blue power last night But when I try to Bang it My Protection light comes on If I turn the volume down it plays fine As soon as I tried to add some bass to Red Comes on
Low voltage at high volumes does amps need enough voltage
What gauge of amp did you use 4 or 8?
4
Nice
I got the same amp, powering p1 12s
Me to hope it sounds good
@@timothynovo1178 it did. I upgraded to p3s and a p1000 amp
I’m also going with the same amplifier Ali’s going with the r2 500x4 powering 6.5 tfosgate and the 6x9 hope for a good sound out of it
It’s going to be too much I have 4 ds 6.5 and the speakers could barely handle it
@@JuanGarcia-nm7tl holy kek really?