How I set up the 24V RGB COB with WLED: th-cam.com/video/oQuzGRDiKKc/w-d-xo.html How I set up easy DIY light strips in my bathroom: th-cam.com/video/zFW94lpUrTI/w-d-xo.html 📣 Head's up! I have VERY helpful light strip videos planned for 2023, so subscribe to this channel so you don't miss those.
what do you suggest for 50' of led lighting to light up stair path...I just need to run it down the side. I want them bright. Im not to worried about diffusion just brightness and having it powered at only one end. I want rgb so I can change colors. programming it to do crazy stuff is not a requirement.
DIY with 5-volt addressable strips gives you higher resolution (and can power the esp32 right from it). It can will require power injection for longer runs, but if you aren't afraid of a little soldering, you can get really nice results.
That looks incredible! Nice job! My most recent set of light strips, I went DIY, and yeah... my soldering still sucks. I felt like I needed the bigger gauge wire to cross a gap, but then I had a hell of a time soldering them to the strips. Even these crimp connectors I got to make it easier, still caused a lot of headaches.
I find that if you just want color and not really sure or don’t really care on the where and specifics, Govee is fine. If you have very specific requirements (needs to be primary lighting for the room), LEDs need to be individually addressable because of a certain effect you want, need to be able to control total brightness (may need power injection), want strips to specifically be on these edges and these under cabinet and these vaulted ceiling trims, extensions tend to be much easier with DIY, then DIY is the way to go. Sometimes you want a corner trim to connect to an edge trim, to connect to an upfiring trim, to a non-diffused downfiring trim and you want them all to go sequentially. Go DIY. There’s no kit solution for that. It’s work going DIY, no doubt about it. And most of the work is research. I think once you get all the right components and tools, install is pretty straightforward.
Definitely want teh COB variant for what I'm planning to install, not a big fan of seeing LED's. DIY kind of speaks more to me, just getting a handle on the whole thing and problemsolving seems like fun. The biggest challenge so far, as you also say in the video, is just figuring out what the heck to buy. There's so much out there and it's not clear at all. Wiring DC stuff is a doddle, soldering is easy, but finding the right components to buy so it all works, that's tough. Especially since I'm also only now getting into the home automation bit for real, took one of my existing Raspberry PI's and slapped a Z-wave transceiver on it, but now I have to wrap my head around Z-wave, Zigbee and all that stuff as well. Still... it should be fun.
Another good option for the diy if you dont want to Solder wires is get a dig uno controller for the lights comes with QLED on it and is small and easy to hide
The decision for many is direct controllability. For example, none of the pre-packaged strips can be controlled by DMX. For a “set-n-forget” rig, then, yeah, prepackaged is the way to go. For my designs I need direct control to work with the rest of my lighting system. That part was kind of unsettling. DIY implies an interest in learning new skills and understanding of new things, like electronics or woodworking, or whatever, so it doesn’t require being an electrical engineer, but it does require an interest in learning something new, so that complaint is invalid.
LED density is measured in LEDs per meter. You can buy much more dense strips for DIY projects than the one you have here. Looks like you are using a 60 LED/Meter strip. You can get them at 144/meter.
Another great video, thank you again. I love how you explain both options so I can decide which is better for my application. Heading over to Reed's Smart Home to check out how to build my own light strip
Great video! I'm looking to shine color from my ceiling onto a wall painted flat black. I don't want to see the LED diodes so I'm wondering if there are LEDs that point or are cut at an angle. In other words, if I'm looking at that wall I just want to see the effect of the light, not the LED diodes. Similar to those under your bed, cabinet, etc. I'm wondering if i need to install a small piece of wood across the ceiling to physically hide the LED strip. Thoughts?
This is such a great video! I’m getting all the information I need, you’re laying it all out in a digestible way . I feel way more informed before I make any purchases . Thank you:)
Are there any options in the USA for in-wall switch panels/controllers for ARGB strips? I'm working on a project for a friend, and she wants to stay away from needing to control her kitchen's strips via an app and would like an in-wall panel that has a standard on/off switch and the ability to change the strips' colors from the wall panel.
Yo this video hase no sense you put a link about the rgbic but it's not the product itself, can't you just click on the link of the thing so we find it in one strike ????????????????? is it this harde to get the things done correctly ??????? And at the minute 07:06 can you tell me did you make that thing that looks like the sword game of Star Wars or did it come with the led and also what kind of led did you order is it a Pro led or M1 Led RGBIC ???? please help.
Hi Reed, great video. Do you happen to know if you can cut the FCOB dreamcolor strips you used and then make use of the remaining, or is that fit for the bin once it's been cut? I'd really like to try and make some use of these strips if i can but the use case i would like to put them too would mean several shorter strips, i'd like to save by buying a larger roll but that's of no use to me if i cn't use the remaining strip once i've cut it. Thanks in advance
So if i wanted to run these BTF addressable dream color lights strips around the entire edge of my daughters bedroom ceiling, which is around 50ft, would I need 2 powersupplies and 2 controllers and 2 wifi processors to get this to work properly? Also, if I wanted it to work with Alexa, would I need anything else? Thanks. Great videos you got on your channel BTW.
I live in a log cabin and am wanting to put lighting on my kitchen ceiling because my ceiling is beams it's so dark. But how do I do that from beam to beam for every section of my ceiling?
I can tell you right now.. get the WS2812b's 300leds per 16.4 ft.. individually controllable far better lighting effect and cheap.. paired with the ESP32(flashed with WLED) or the white box with WLED preinstalled, the preinstalled box is $22.00 or $26.00 with mic for music sync.. I got 3 ESP32 boards for $12.00
I'm going to go to DIY route because of the reparability and I already have the equipment necessary to put it together and I have never went to college for it.
so i’m looking to wirelessly control led strip lights mounted to each drum in my sons marching band. how would you attach that project? i am a little lost on controlling led lights wirelessly on a football field
Hello, I haven't gotten a proper answer from anyone to the following question: I have a smart home system built on Apple Homekit with about 10 different hubs and around 200 different additional devices. Could I use Home Assistant system alongside it in a way that it doesn't disrupt my current Apple Homekit system? In other words, can these two systems operate simultaneously? What interests me about Home Assistant are its extensive automations. Also, thank you for your very good videos. I follow you avidly here from Finland.
I need your help I want to put some lights to my garage doors, try to make their run on red when garage is going to open, green when is open and another color when is close but I don't know how to make them go smart
Not being able to cut the Govee M1 strips at lengths less than 1.5ft (where solder line is), makes them very limiting, frustrating in fact. Begrudgingly, now I have to research WLED, controllers, etc. just so I can be able to cut to custom lengths for toe kicks, under range hood, shelving, etc. Chris Maher is arguably the best at it on TH-cam but it’s A LOT to get familiar with. Govee really needs to allow cut points every 2” or so. Also, the directions for using / installing those controllers has my head spinning. 🤦🏻♂️ And how many strips will work in a series on a single power source?
Can you advise me what the absolute brightest+saturated bulb is? for me, a bulb should be super bright and have super good colors. I don't care about special stuff, just that i can change from rgbw with the brighrst possible colors. thanks
I have installed a three way Meross wall switch and experiencing some problems . Installed just one . The light does switch on and off at the Meross switch. But at the other switch the light will some times come right back on after turning off the switch. Do I have it wired wrong ? Thanks in advance ,love the videos.
Which mobile app are you using with the Gledopto controller? I can’t seem to find one. You showed one being used in the video. I have mine connected through my 4th Gen. Echo that has Zigbee built in. But I was hoping to use a dedicated Gledopto app or similar app instead of Alexa. Thanks!!
hello, can you tell me what settings you used in WLed for the Cob led strip? I bought one with 720 addressable LEDs per meter and I can't configure it. it is the led strip that was also left in the description of the clip. thank you
Great Video! One thing to note is that the Govee M1 Lightstrip does not have separate LEDs for white, so it can't produce a very warm white. If you only want to use the RGB colors anyway, it doesn't matter.
I haven't tried to get it connected to SmartThings yet. Looks like some people did get it working with SmartThings with a device handler a while ago github.com/damien67/WLED-SmartThings but I'm not sure with all the changes to SmartThings if that would still work.
I have bought the same fcob strip but for the life of me I cannot get it to work with WLED…it just flickers different colors out of control (tried different board - using esp32, different power supply ecc)…how did you do it with wled? Can someone help?
cool, I'm going to replace the light strips in my bed soon because they are just RGB, but I really like the remote they came with, so I'm coding a aurdeno for control with a ir receiver so the new lights will be RGBWW
I need a led strip that can go a long way on 1 or 2 power sources for Crown Molding. All the LEDs I see are outrageously priced, or they don't have full color and full whites for a responsible price
The DIY RGBWW light strips I have in the description should fit what you are looking for. Make sure to get 24v so you will have less resistance and lower voltage drop with a long length.
What if I told you there are WLED preflashed controllers that require no soldering and you can still pick the strip you want and pair it with a matching power supply
There is a huge problem with GOVEE... they do NOT SELL separate controllers.. I bought the 65' version.. and it comes with 2, 33' rolls.. well if you want to put them in different rooms.. you are out of luck or even if you want to put them end to end.. NOPE not going to happen you have to be within the distance of the dual cables coming out of the controller box.. so NOT GOOD for that.. just Saiyan make sure you get as close to the size run that you need.. or you will be wasting money .. I love the DIY with individual adjustable leds.. and then just get a separate controller.. they have some that are super easy to use and are universal ..
So I have an question I want to use the addressable BTF Leds with the SP511 controller to go around my IKEA peg boards to them light up. Will that all I need or would I also need to buy the connectors for the corners as well? Oh yeah 2 power supplies because I have 2 peg boards and they will be on different sides of the wall
Welcome to WLED! I’ve been looking for a 60 led/meter individually addressable strip that has each LED as being brighter than the ws2812b strips, anyone know of something? Meaning if it had one single led on full brightness, it would be brighter than a ws2812B on with a single pixel on full brightness.
How I set up the 24V RGB COB with WLED: th-cam.com/video/oQuzGRDiKKc/w-d-xo.html
How I set up easy DIY light strips in my bathroom: th-cam.com/video/zFW94lpUrTI/w-d-xo.html
📣 Head's up! I have VERY helpful light strip videos planned for 2023, so subscribe to this channel so you don't miss those.
what do you suggest for 50' of led lighting to light up stair path...I just need to run it down the side. I want them bright. Im not to worried about diffusion just brightness and having it powered at only one end. I want rgb so I can change colors. programming it to do crazy stuff is not a requirement.
When someone says "LED diodes" it's such a pet peeve of mine... The D in LED stands for diode! 😁
😂
Similar to people saying "ATM Machine" M already stands for Machine😂
PIN number
UAT test
HIV virus
RAS syndrome
@@ShaamanRyu you found more😀😀😀
@@harenthiran don’t encourage me
But…
ABS system
LCD display
UPC code
DIY with 5-volt addressable strips gives you higher resolution (and can power the esp32 right from it). It can will require power injection for longer runs, but if you aren't afraid of a little soldering, you can get really nice results.
I'm happy that this time you address the CRI score of the led strips. Cheers! :)
LED Lightstrips will forever be my favorite Lights thanks to you reed. Thank you. 🥰
This video help me building my room. Thank u. DIY>preassembled
That looks incredible! Nice job! My most recent set of light strips, I went DIY, and yeah... my soldering still sucks. I felt like I needed the bigger gauge wire to cross a gap, but then I had a hell of a time soldering them to the strips. Even these crimp connectors I got to make it easier, still caused a lot of headaches.
2:12 the rubber band you've been looking for is by the left side of the cabinet on the floor. :)
I find that if you just want color and not really sure or don’t really care on the where and specifics, Govee is fine.
If you have very specific requirements (needs to be primary lighting for the room), LEDs need to be individually addressable because of a certain effect you want, need to be able to control total brightness (may need power injection), want strips to specifically be on these edges and these under cabinet and these vaulted ceiling trims, extensions tend to be much easier with DIY, then DIY is the way to go.
Sometimes you want a corner trim to connect to an edge trim, to connect to an upfiring trim, to a non-diffused downfiring trim and you want them all to go sequentially. Go DIY. There’s no kit solution for that.
It’s work going DIY, no doubt about it. And most of the work is research. I think once you get all the right components and tools, install is pretty straightforward.
Good comment. Do you know if using a zigbee controller OS better than this soldering method ?
Definitely want teh COB variant for what I'm planning to install, not a big fan of seeing LED's. DIY kind of speaks more to me, just getting a handle on the whole thing and problemsolving seems like fun. The biggest challenge so far, as you also say in the video, is just figuring out what the heck to buy. There's so much out there and it's not clear at all. Wiring DC stuff is a doddle, soldering is easy, but finding the right components to buy so it all works, that's tough. Especially since I'm also only now getting into the home automation bit for real, took one of my existing Raspberry PI's and slapped a Z-wave transceiver on it, but now I have to wrap my head around Z-wave, Zigbee and all that stuff as well. Still... it should be fun.
In our neighborhood we are staying to see outdoor lightstrips under the eaves of the house. Have you done outside lightstrips yet?
Same with out neighborhood. I haven't done those yet but it would be a fun project!
Another good option for the diy if you dont want to Solder wires is get a dig uno controller for the lights comes with QLED on it and is small and easy to hide
The decision for many is direct controllability. For example, none of the pre-packaged strips can be controlled by DMX. For a “set-n-forget” rig, then, yeah, prepackaged is the way to go. For my designs I need direct control to work with the rest of my lighting system. That part was kind of unsettling. DIY implies an interest in learning new skills and understanding of new things, like electronics or woodworking, or whatever, so it doesn’t require being an electrical engineer, but it does require an interest in learning something new, so that complaint is invalid.
I’ve been seeing a lot of these DIY options lately. Been debating on doing it myself.
7:06 I couldn!t understand this part. What did he do to the strip led?
Do you have a tutorial for plastered in LED for ceilings in a home? What would something like that take to make it happen? Power, durability? Etc
That was very informative I wasn’t aware about the diy aspect
LED density is measured in LEDs per meter. You can buy much more dense strips for DIY projects than the one you have here. Looks like you are using a 60 LED/Meter strip. You can get them at 144/meter.
Another great video, thank you again. I love how you explain both options so I can decide which is better for my application. Heading over to Reed's Smart Home to check out how to build my own light strip
Who hasn’t been in the same predicament as occurred in the outtro?
Deym, those look so much better than expected
Is the ESP32 cover you use in this video something you 3D printed or is it available for purchase through Amazon?
You know i know diy would’ve been probably better. But ive just installed my govee m1 strip and it’s honestly doing everything i want it to do
Love the look of them cob ones, time to go look for some :)
I have some generic IR led strips, which are quite old now, with the controller removed and a cool device called the RGBW2 from shelly
A house full of light🤩🤩
Great video! I'm looking to shine color from my ceiling onto a wall painted flat black. I don't want to see the LED diodes so I'm wondering if there are LEDs that point or are cut at an angle. In other words, if I'm looking at that wall I just want to see the effect of the light, not the LED diodes. Similar to those under your bed, cabinet, etc. I'm wondering if i need to install a small piece of wood across the ceiling to physically hide the LED strip. Thoughts?
This is such a great video! I’m getting all the information I need, you’re laying it all out in a digestible way . I feel way more informed before I make any purchases . Thank you:)
I love the little end scenes after each vid 😂
Are there any options in the USA for in-wall switch panels/controllers for ARGB strips? I'm working on a project for a friend, and she wants to stay away from needing to control her kitchen's strips via an app and would like an in-wall panel that has a standard on/off switch and the ability to change the strips' colors from the wall panel.
What do you think of tapo
just an fyi goove has a "desk strip" which is already defused and its 84 leds per meter instead of the m1 which are 60 I believe.
Wanna a dedicated video on Philips hue lights.
Adding a splitter works vary well thanks I added ur video to my channel
Does the controller method of connecting it mean I don’t have to solder anything?
Is there a video on how to use that option?
Yo this video hase no sense you put a link about the rgbic but it's not the product itself, can't you just click on the link of the thing so we find it in one strike ????????????????? is it this harde to get the things done correctly ???????
And at the minute 07:06 can you tell me did you make that thing that looks like the sword game of Star Wars or did it come with the led and also what kind of led did you order is it a Pro led or M1 Led RGBIC ????
please help.
With the DIY, can you turn them on and off with a switch as well as app
It looks like you installed them in the 10mm wide v channel diffuser. No issues with the strips being 12mm? Looked like the excess bent easily enough.
Yeah they seemed to fit fine. Those corner channels are pretty forgiving on the width.
Hi Reed, great video. Do you happen to know if you can cut the FCOB dreamcolor strips you used and then make use of the remaining, or is that fit for the bin once it's been cut?
I'd really like to try and make some use of these strips if i can but the use case i would like to put them too would mean several shorter strips, i'd like to save by buying a larger roll but that's of no use to me if i cn't use the remaining strip once i've cut it. Thanks in advance
What lamp is that next to the corner strip ? Looks cool
So if i wanted to run these BTF addressable dream color lights strips around the entire edge of my daughters bedroom ceiling, which is around 50ft, would I need 2 powersupplies and 2 controllers and 2 wifi processors to get this to work properly? Also, if I wanted it to work with Alexa, would I need anything else? Thanks. Great videos you got on your channel BTW.
I live in a log cabin and am wanting to put lighting on my kitchen ceiling because my ceiling is beams it's so dark. But how do I do that from beam to beam for every section of my ceiling?
What products would you recommend for a google smart room? Are wifi products good or should i just go all in an Aqara?
Govee!
Just dropped in to say I always watch your uploads. A little hammy sometimes but still great 😂 keep up the good work 👊
I can tell you right now.. get the WS2812b's 300leds per 16.4 ft.. individually controllable far better lighting effect and cheap.. paired with the ESP32(flashed with WLED) or the white box with WLED preinstalled, the preinstalled box is $22.00 or $26.00 with mic for music sync.. I got 3 ESP32 boards for $12.00
Hey mate what's the light bulb you've got in your sonos lamp ??? Looks awesome !!!
I'm going to go to DIY route because of the reparability and I already have the equipment necessary to put it together and I have never went to college for it.
What’s that lamp used in the background on the white shelf/stand?
Ws2815 oder Govee M1 , 2x 7,5m getrennt an gegenüberliegenden Wänden?
so i’m looking to wirelessly control led strip lights mounted to each drum in my sons marching band. how would you attach that project? i am a little lost on controlling led lights wirelessly on a football field
Hello, I haven't gotten a proper answer from anyone to the following question:
I have a smart home system built on Apple Homekit with about 10 different hubs and around 200 different additional devices. Could I use Home Assistant system alongside it in a way that it doesn't disrupt my current Apple Homekit system? In other words, can these two systems operate simultaneously?
What interests me about Home Assistant are its extensive automations.
Also, thank you for your very good videos. I follow you avidly here from Finland.
the preassembled are literally the same strips but with some waterproofing layer and diffuser integrated
what is the cost difference between govee m1 and diy for same length
I need your help I want to put some lights to my garage doors, try to make their run on red when garage is going to open, green when is open and another color when is close but I don't know how to make them go smart
Not being able to cut the Govee M1 strips at lengths less than 1.5ft (where solder line is), makes them very limiting, frustrating in fact. Begrudgingly, now I have to research WLED, controllers, etc. just so I can be able to cut to custom lengths for toe kicks, under range hood, shelving, etc. Chris Maher is arguably the best at it on TH-cam but it’s A LOT to get familiar with. Govee really needs to allow cut points every 2” or so.
Also, the directions for using / installing those controllers has my head spinning. 🤦🏻♂️ And how many strips will work in a series on a single power source?
Cool video great work but I do like the Govee more in the corner I really like the actual colors of Govee's Strip
Can you advise me what the absolute brightest+saturated bulb is? for me, a bulb should be super bright and have super good colors. I don't care about special stuff, just that i can change from rgbw with the brighrst possible colors. thanks
Can you link the deep Chanel covers that you’ve shown in the video that you couldn’t see the individual diodes?
I have installed a three way Meross wall switch and experiencing some problems . Installed just one . The light does switch on and off at the Meross switch. But at the other switch the light will some times come right back on after turning off the switch. Do I have it wired wrong ? Thanks in advance ,love the videos.
Hey Reed how do you get the channel with diffusion to stay on the wall like that?
Great video. Do you have any thoughts about Hue compatible lightstrips?
Reed, COB stands for “chip on board”. It is a type of integrated circuit manufacturing process.
Funny, sitting here watching this as I covert some new Govee lights to WLED!!
Wait, what! Converting Govee? How?
@@phillips_9150 correct. Just cut off the Govee controller and add a diguno or similar controller. Worked great.
Is there a 12v RGBW option that you’d prefer that’s also wled compatible?
i hand soldered 90 connections of power, ground & data of those ws2812b to make a color 30 led 7 segment adruino clock for 3 days.
Which mobile app are you using with the Gledopto controller? I can’t seem to find one. You showed one being used in the video. I have mine connected through my 4th Gen. Echo that has Zigbee built in. But I was hoping to use a dedicated Gledopto app or similar app instead of Alexa. Thanks!!
Is the ESP32 cover you use in this video something you 3D printed? Where can I finde the stl-file?
hello, can you tell me what settings you used in WLed for the Cob led strip? I bought one with 720 addressable LEDs per meter and I can't configure it. it is the led strip that was also left in the description of the clip. thank you
Great Video! One thing to note is that the Govee M1 Lightstrip does not have separate LEDs for white, so it can't produce a very warm white. If you only want to use the RGB colors anyway, it doesn't matter.
but how long they look good?
Hopefully you got some extras to string some lights for your dog house.
Awesome video, as always. Is there any way to set something similar to this up in Smartthings?
I haven't tried to get it connected to SmartThings yet. Looks like some people did get it working with SmartThings with a device handler a while ago github.com/damien67/WLED-SmartThings but I'm not sure with all the changes to SmartThings if that would still work.
Well it’s worth a try. Thanks for the reply 😊 And huge Thank you for your videos, I really enjoy watching them.
Hi.you cand control DIY with govee app ? or to combine the strip so that you can control them with the govee app?
i wanna to sync with govee T3 camera
Can you sync these up with govee? Like govee dreamview?
Did you know that Govee introduced a preset feature that can be activated with google assistant? It has always worked with alexa by the way....
Hi, again a great video! :-) Question: To which automation ecosystem did you connect this DIY solution?
Will those COB DYI work with HomeKit?
I am a smartthings user and is there a controller that works best with that?
I have bought the same fcob strip but for the life of me I cannot get it to work with WLED…it just flickers different colors out of control (tried different board - using esp32, different power supply ecc)…how did you do it with wled? Can someone help?
cool, I'm going to replace the light strips in my bed soon because they are just RGB, but I really like the remote they came with, so I'm coding a aurdeno for control with a ir receiver so the new lights will be RGBWW
Will you send instructions on how you did it
I like your t-shrt. Where'd you get that?
What camera do u use to record your videos?
I need a led strip that can go a long way on 1 or 2 power sources for Crown Molding. All the LEDs I see are outrageously priced, or they don't have full color and full whites for a responsible price
The DIY RGBWW light strips I have in the description should fit what you are looking for. Make sure to get 24v so you will have less resistance and lower voltage drop with a long length.
How Long of a run can I do on one 24v? I think I need around 300 linear ft to run.
diffusers rule of thumb : distance of diffuser to led >= distance fro. LED - LED
Great Video!!, will check out the second channel video on how to use the DIY route
Where I can find the desk lamp, I.2ve searched the internet but couldn't found it, can someone please help me with that
Is there a good diy Bluetooth controller?
Is it just me or do they not sell those kasa lightstrips anymore
What if I told you there are WLED preflashed controllers that require no soldering and you can still pick the strip you want and pair it with a matching power supply
What if I told you I already said it in the video 5:05
@@SmartHomeSolver 😂
lol at the ending. Never seen your channel before so wasn't expecting comedy
Hello wanted to see a video on samsung smart things station. Review and automation Ideas.
There is a huge problem with GOVEE... they do NOT SELL separate controllers.. I bought the 65' version.. and it comes with 2, 33' rolls.. well if you want to put them in different rooms.. you are out of luck or even if you want to put them end to end.. NOPE not going to happen you have to be within the distance of the dual cables coming out of the controller box.. so NOT GOOD for that.. just Saiyan make sure you get as close to the size run that you need.. or you will be wasting money .. I love the DIY with individual adjustable leds.. and then just get a separate controller.. they have some that are super easy to use and are universal ..
Thanks Reed.
So I have an question I want to use the addressable BTF Leds with the SP511 controller to go around my IKEA peg boards to them light up. Will that all I need or would I also need to buy the connectors for the corners as well? Oh yeah 2 power supplies because I have 2 peg boards and they will be on different sides of the wall
Sorry but I didn't like the WIZ mainly for the dark zones in them.. to large of gaps between the LEDs
Awesome content. Glad you are making money off those amazon affiliate links!
Anyone know what lamp that is in the background?
Thanks Reed great Video. I had suggested a WLED video a few months ago. I’ve got totally addicted to using it . Hope you are having fun with it.
Welcome to WLED! I’ve been looking for a 60 led/meter individually addressable strip that has each LED as being brighter than the ws2812b strips, anyone know of something? Meaning if it had one single led on full brightness, it would be brighter than a ws2812B on with a single pixel on full brightness.
2815 or sk6812