You mentioned if you wait too long between the mold and the cast, that the alginate will shrink and distort. Would pouring a cast, and just leaving it prevent this? Would you be able to remove the cast at a later time and retain the mold's form?
Pouring a cast will help a little, but the alginate will start drying out regardless of what is inside the mold. Best to do you casting fast for accurate results. Now, I have used the same mold over a dozen times to cast fast setting silicone and the last pull was noticeably smaller than the first.
Do you ship to the UK? If you don't is there any similar products available, any good UK suppliers? I've tried to look but I don't understand what I'm looking for! Thanks!
Always nice to see more videos! Also, if I want to get a poseable cast, would embedding a wire armature work? or the silicone might be too thick for it to properly bend?
Hi, I ran into trouble during silicone casting stage, I quickly and thoroughly mixed alginate and poured into mold tube and during the silicone casting the alginate started to release water which didn't let silicone to cure at all, it started releasing it after 30 minutes only and silicone needs to be cured in 30-2hrs, I even tried to use lamp and even oven but it got worse... What shall I do I cannot find right platinum silicone. HELP 🥺
@@brickintheyard I used alginate for teeth impressions and generic mold making platinum silicone 0A hardness, for pigmenting I used oil-based paint and DIY flock made from polyester fiber. I did small sample batches and everything was good, until I tried to hollow-cast the alginate mold
Would you be able to post a current price for all your supplies so we each know if this is even in our budget? I don't imagine you used $500 in product but I don't have any idea otherwise.
A lot of pricing will be specific to a given cast, but here's the breakdown for what we did here: Genesis V ~$16, Mold tube: ~$9, Gel-25 $28, Pigment ~$.50. All of those prices fluctuate based on the amount of material you purchase so these numbers are probably on the high end, purchasing in small quantities.
Do not throw that away, it's a waste. Instead, chop it up into smaller chunks. Next time you pour an algenite, use the bigger chunks along side the liquid so you don't have to use as much liquid.
Alginate, once dried out, would cause distortion problems if added to fresh alginate as it would pull moisture from the fresh alginate causing it to warp. :(
@@MehndiEssence7Cost will vary depending on the quantity you order and other variables such as pigments and flocking. Go to our website for pricing. Thanks!
Would this method and materials be safe for ...more "sensitive" areas of the body?
Yes. Alginate can be used to mold all parts of the body.
You mentioned if you wait too long between the mold and the cast, that the alginate will shrink and distort. Would pouring a cast, and just leaving it prevent this? Would you be able to remove the cast at a later time and retain the mold's form?
Pouring a cast will help a little, but the alginate will start drying out regardless of what is inside the mold. Best to do you casting fast for accurate results. Now, I have used the same mold over a dozen times to cast fast setting silicone and the last pull was noticeably smaller than the first.
@@brickintheyard Good to know. Thanks!
Hello .. amazing job
Can you write down the materials you used?
We are closed now, but you can order supplies through Fox and Superfine in Georgia or BJB Enterprises in Tustin CA.
Great video, definitely a nice quick way to mold an arm
Burry half of it so just the hand is sticking up in the woods
🤣🤣🤣
Do you ship to the UK? If you don't is there any similar products available, any good UK suppliers? I've tried to look but I don't understand what I'm looking for! Thanks!
Check BJB Materials website for international distributors.
Please make another body silicone to
ok
About how much silicone did you use to make three models, and can you tattoo on the models?
Can ACCU-CAST 380-CC cast cast arms fingers and hands too?
Yes. 380 is just a faster formula.
How can you make a prosthetic arm that’s like a face mask?
since the alginate 5 has been discontinued what can I use as a substitution for that but that will do the same thing?
590 is the best alternative to Genesis V. I’ll update the links
@@brickintheyardis it the ACCU-CAST 590
@@brickintheyard the ACCU-CAST 590?
@@yodakotaa_ yes
Could I use this to make a candle??
Not the alginate, but we have several silicones for that. Try 5110 or 5130. Both are well suited for soap and candle making.
Which brand Alginate did you use ?
Sadly, this alginate formula has been disconnected. :(
Always nice to see more videos! Also, if I want to get a poseable cast, would embedding a wire armature work? or the silicone might be too thick for it to properly bend?
You could do that with a Gel-10 hand, Gel-OO hand, or a Gel-25 hand that has been "deadened."
Please what are the name's of the Chemicals you mix in making the mold and it didn't hurt her hands??
Alginate is safe for skin and even mouth contact so, thankfully, it doesn't hurt anyone.
how much plat sil silicone was used for the hand?
If I was to pour that now, I would use TC-5130F. I think this took about 2.5lbs.
Hi, I ran into trouble during silicone casting stage, I quickly and thoroughly mixed alginate and poured into mold tube and during the silicone casting the alginate started to release water which didn't let silicone to cure at all, it started releasing it after 30 minutes only and silicone needs to be cured in 30-2hrs, I even tried to use lamp and even oven but it got worse... What shall I do I cannot find right platinum silicone. HELP 🥺
There are a lot of variables to consider in order to trouble shoot. What products are you using?
@@brickintheyard I used alginate for teeth impressions and generic mold making platinum silicone 0A hardness, for pigmenting I used oil-based paint and DIY flock made from polyester fiber. I did small sample batches and everything was good, until I tried to hollow-cast the alginate mold
How would you trim it if any bubbles on the hands, just a sharp knife?
An Xacto knofe works well for trimming air bubbles.
Would you be able to post a current price for all your supplies so we each know if this is even in our budget? I don't imagine you used $500 in product but I don't have any idea otherwise.
A lot of pricing will be specific to a given cast, but here's the breakdown for what we did here: Genesis V ~$16, Mold tube: ~$9, Gel-25 $28, Pigment ~$.50. All of those prices fluctuate based on the amount of material you purchase so these numbers are probably on the high end, purchasing in small quantities.
Thanks.
How would you create a silicone mold for a torso
Check our video library for more extensive videos. There's a link in the video description.
What is it you use to make the mould with?
A 5"x12" plastic tube.
@@brickintheyard No I meant the stuff you pour in the tube thanks
Do not throw that away, it's a waste.
Instead, chop it up into smaller chunks. Next time you pour an algenite, use the bigger chunks along side the liquid so you don't have to use as much liquid.
Alginate, once dried out, would cause distortion problems if added to fresh alginate as it would pull moisture from the fresh alginate causing it to warp. :(
Brick In The Yard Mold Supply would mulching it work as a filler?
Used alginate would probably be best for the compost pile.
Brick In The Yard Mold Supply I'm really interested in mold making for cosplay. Do you have a seller in Michigan?
We do ship to the Michigan. 3 business days transit time.
Can i put inside plaster figure ?
Not sure what you mean?
How can I paint the silicone
th-cam.com/video/IjloBWSDdWw/w-d-xo.htmlsi=ES1j7nXmXSgOTwcx
Do you sell this hand?
No, but we sell all the supplies you need to make your own.
@@brickintheyard total cost?
@@MehndiEssence7Cost will vary depending on the quantity you order and other variables such as pigments and flocking. Go to our website for pricing. Thanks!
wiw those bar stools look familiar
Bar stools??
I like the girl's tattoo on her left hand, I had to say it :D
Ha!
WILL YOU SELL ME A LEFT HAND AND RIGHT HAND IN SILICONE AND WHAT IS THE COST?
We supply the materials to do this process, but we do not do custom work. :(
Muy interesante 👍😃