How to Replace Front Brakes 09-14 Nissan Murano
ฝัง
- เผยแพร่เมื่อ 27 ส.ค. 2024
- Buy Now!
New Brake Kit from 1AAuto.com 1aau.to/ia/1APB...
1A Auto shows you how to repair, install, fix, change or replace your own worn, squeaky, fading old brakes. This video is applicable to the 09, 10, 11, 12, 13, 14 Nissan Murano
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oYr/1AX...
• Pry Bar 1aau.to/ofg/1AX...
• 10mm Wrench 1aau.to/okp/1AX...
• 14mm Socket 1aau.to/oPe/1AX...
• 19mm Socket 1aau.to/omV/1AX...
• 22mm Socket 1aau.to/obt/1AX...
• 1/2 Inch Breaker Bar 1aau.to/ohB/1AX...
• Ratchet 1aau.to/oZI/1AX...
• Torque Wrench 1aau.to/op5/1AX...
• Brake Parts Cleaner
• Rust Penetrant
• Floor Jack 1aau.to/oox/1AX...
• Jack Stands 1aau.to/ooG/1AX...
• Large C-Clamp
• Wire Brush 1aau.to/oc8/1AX...
For More Info visit us at 1aau.to/h/aIw/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
This is one of the best how to break job videos I have ever seen! Thanks ❤
Not sure why u bled the brakes? I just pull the lid off master cylinder and push the piston back on the caliper introducing no air in to the line
Don’t even need to remove the lid, just go slow and it’ll be fine
so that you're not pushing dirty fluid into the abs unit, those are expensive to replace.
@@johnmiller9219 ah huh lmfao. How did dirt get in the line unless it is from pitted rusting lines. I have as much experience as you and this did not need to be done!!!!!!
There is no need to open the bleeder unless there was air in the line to begin with.
+Diemerstein Thanks for the tip!
or if you want to bleed the line.
I saw the nail when she was putting the tire back....great video....thanks for sharing.
+L Grullon Thanks for checking us out!
Very clean professional job. Great video. Thanks!
You guys are awesome keep up this hard work i have fix so many cars and trucks watching y'all's videos thank you so much
Just FYI, on 2013 Model Year and newer, the bracket to knuckle bolts only need 91 foot/lbs torque, according to Haynes.
Great and perfect explanation on brake pad replacement! How do I find more videos with you explaining procedures? Thanks
i must be the only person who does this but every one of my brake jobs when i take of the brake caliper brackets i sandblast them. then paint them with high temp flat black paint.
Thank you so much for this very informative video.
+Nimrod Barnes Thanks for checking us out, glad to hear this helped! 1aau.to/m/Shop-1AAuto-c
You better go girl love it
Do I have to change my rotors every time I change the brakes or how do I know when I need to change them.
@quintin1125 You have to measure the thickness of the rotor with a digital caliper tool. The minimum thickness allowed is stamped on the top of the rotor. You may need to remove some rust with a wire brush or fine sand paper if applicable to see it.
Is the rotor pin with black rubber harder to slide in and out then the other pin without rubber
No silicone on back of pads or on caliper where back of pad touches and also on piston where pad touces?
Question, you always have to change rotor?
Anybody else notice the nail on the tire
how did u know there is air when bleeding?
If you do not bleeding the brakes, would you have issues with the pads grabbing the rotor. I can feel the front brakes shim-ing
+Kevin Linville Thanks for the tip!
No, you will be just fine. There's no need to open up the bleeder. Just push caliper back slowly
There is a screw in the tire?
That rotor goes on the passenger side
15:00 Nail or screw in tire.
In 4:10 do u have to squeeze out the water or no
+justin mendez The caliper should be decompressed in order to install new brake pads properly. If you do not, the pads will not fit as the area will not be big enough to fit in.
should it be 122 nm? I think 122 ft lb is too much.
+Jun Wang Sue says 22 ft lbs not 122 in the video. Thanks for watching!
@@1AAuto 122 bracket bolts, 22 caliper bolts.
Did you notice the nail in the tire just FYI
Two Thumbs Up....
+Mario S. Thank you!
Good video thank you !
+james pha Thanks for the feedback!
And if this tech was not being filmed, she wouldn't had brushed anything.... Plain spray of brake cleaner. When bleed the caliper... Nothing could have got in the line as it is compressed. She would have just opened the master cylinder like anyone else. I'm just wondering why she didn't glassbeed , then paint everything😂😂😂😂😂. The HP rotors... Seriously, it's an SUV
Great job! Did you happen to see what appears to be a nail in the tire?
no wonder y’all charge what y’all charge for doing all this unnecessary stuff.. i just needed the brakes changed that was it…