Replace speaker wires. Check fuses. Make sure your ground is good and check the impedance. You might not have been getting enough voltage. Usually the amp is good when you disconnect speaker wires and it comes out of protection mode
I repaired one just like it, was in protect due to voltage regulator! These are nice class D amplifiers! But sometimes having the bass boost all the way up is an issue as well! This amp will run on as little as 10V at least factory claims it will handle 10-14V!
when my soundstream trx 1500 was doin that ,i found out that it was my 12 volt hook up . had to rehook up my 120 amp fuse . that line has to be tight and pulling current.
Hmmm, Ive had the same problems, try opening up the amp and looking for any burnt out or melted connections, if there are, it definitely is the amp. If not, it could be how you connected it or what you connected it to. 600 watts is a lot and can overdrive some batteries with a small alternator. But that probably isn't it because one, it goes into protection without the subs, and two, you have a capacitor. Also, try lowering the imput volume, doesn't hurt to try.
blown sub. a blown sub can be like taking the + & - and twisting them together. it's called a short. 2ohms is less resistance than 4 ohms etc. so it's like the amp has zero resistance ( zero ohms) no Amp can't handle zero ohms. protection mode it is. any questions?
Juan m. I got some t7 tarantula soundstream 12" subwoofers and there good . 800 watts each hooked to a trx 1500 tarantula amp . takes the power and if it does blow ,theres a recone kit available for them .
9 times out of 10, amps enter protection mode because you did something your not supposed to. like turning the settings up you high, or running subs that are lower ohms than it rated for
@Silvershredder16 forgot to mention the amp is a 2 channel boss 1000 watt max amp and i brigged the sub connections so their only using 2 of the terminals on the amp for max power
your only useing a 1/2 F cap you need a 1 to 2 F cap. for starters then double check all of your connection to make sure that they are making a good connection.
if i turn up the volume to high and my amp getting in protection mode .. so i turn off the head using .. after 5 minutes i can play it again . then got protection mode again .. and you got any issues that would could be??
What gauge is your wiring harness? Because you dont want to go to big with a small amp because 600 watt amp is to small of an amp for those subs. Im sure thats your problem. The bigger the wire harness the more power your gonna bring to the amp which is gonna put ur amp into protection mode so you dont fry it. You would have to get a bigger amp (1000 watts) if you have 15in subs or (800watts) if you have 12in subs. Or change the wire harness. You should have a 6 or 8 gauge harness with a 600 watt amp!!!! Definitely not a 4 or 0 gauge.
Try to put a bigget fuse I have a boss 1 channel monoblock I was having the same problem but then I checked all my ground wires and power wires and remote wires and the problem was I had to put more stronger fuse so now instead of running 2 25 fuse I decided to put 40 2 40 fuse meaning you have to run 80 and always check your ground wire sometimes if your ground wire is not perfectly tight the way it needs to be tight it's going to make your aunt go to protection mode I hope this advice can help you good luck with your project also try to get a better power wire especially if you're a monoblock the power wire and the ground wire supposed to be some strong thick gauges that way your aunt does not go to protection mode I was looking at your video and I seen your power wires burning like a three or four gauge try using like a zero gauge
I had the same problem with an amp. Got the system tested and they tried a different sub and it was fine. When they took the sub out the coils were black
Blue led indicator bulb of my pioneer gm d-9601 class-d car amplifier starts to blink & sub woofers produces distorted sound after playing it for more than one hour. Plz let me know what may be the reason for that ?
best way to testturn ever thi ng down on amp meaning gain bass boost then hook up one sub go from there sumtimes amp heatin up thats y they do it or to much power given to the sub or taken
@jairo Martinez I eventually just gave up and bought a new amp. The amp was pretty old anyways. I went to best buy and bought a Polk audio for about $200 I'll upload a new video so you guys can check it out .
Brother if u need amps hmu. Fuck be and all chain stores .pawnshop sukiyaki my did I got best prices brother. I got 3namps right now that range from 300 ton400 bucks for 90bones . Rockford. Jbl. Alpine etc I will hook u up
when two kicker subs that come in a box made by kicker are 4 ohms each and are in that oem box that means you are running 2 ohms with both speakers combined. when you bridged it you might of possibly put them in 1 0hm you must put it back to normal so it can run 2 ohms again as opposed to the setup you have now in this video which based on what youre saying i can asume is 1 ohm
Ok. 1st, is your sub wired 8ohm or 2 ohm final impedances(per sub)? 2nd, if your amp is capable of 1ohm? If I remember correctly, the lowest impedance the old school Kicker amp can go is 2ohm. If it keep going into protection mode, your final impedance on your subs are setup up @ 1ohm, which too low of an impedance for that amp and goes into protection mode. Try removing all speaker cables and run 1 sub, 1 coil and see if it still goes into protection mode. If it still goes into protection mode, something wrong with your amp. Probably a bad output mosfit.
My amp is a monoblock and I got 3 subs hook up to it. A 1ch amp can run 2 subs, just depend what impedance u running ur subs on and what the lowest amp amp can go.
Hey bro I think it's ur capacitor take it off and just wire it normal without it see why happens and and if not go under ur hood check fuse if it not melted er anything tell me if that helps
That's why it goes into protection mode because u have them bridged mine did the same exact thing it goes into protection mode because ur amp is getting too hot because u have them bridged
Turn the Filter off and then see what happens Also turn the Gain all the way Down and if you have a Level nob for volts turn it all the way to the right for the lowest volt setting,and use that seat belt bolt under the back seat too.Grind all the paint off of it and around it.Also get some Subs that you can't blow up no matter how much you turn it up....
Hi.The fact that subs are disconnect should allow your amp to go off protection.jus switch your radio off and back on.reset.if it's still in protection then it can be a number of faults like loose positive contact on fuse on battery if you have.or it has a internal fault like burnt or faulty mosfets etc.need to remove test and replace by a technician .only then will it come of protection .
Did you fix problem? Cause I did. I changed all wires. Also if you have different guage wires on speakers inside and out have to be the same. Try that and let me know if that worked caused it worked for me.
i have the same problem with mine! i got 2 12 inch kickers at 400 watts rms each and 1000 watt amp max. everytime i turn the volume up the subs shut off and the amp goes into protection mode sometimes even does it when the volumes not even loud. i dont know if the amp is bad or i need new wiring but i just need my damn subs to work without shutting off! haha
hey im having the same problem... someone told me my amp is no good... so a got a new amp... worked good for like 3 weeks... and new started going in to protections same as my other one... I notice it my by my sub... I put another one.. and some times it goes into protection... once I turn the car off... and back on than it works again... its obvious I still have a problem.... please someone help
manny diaz I have a problem almost like this. Mine only goes into protection mode while im driving. When I park, turn the radio off and back on it plays with no problem. I JUST DON'T GET IT.
I was having same problem I got a 2400 Watt kicker amp was,bumping good n then the subs stopped I thought it was,amp but no I had 1 out of my 2 12 " subs blew I disconnected the blown sub stopped going into protection!!
i had same problem the reason why for mines was because o had everything up on my headunit and my amp up soo just tune dwn the headunit Eq see if dat works
Kevin Scott I got a autotek mean machine 2000w and with no wire but power ground remote and R/cA wires hooked up lights all come on but stay red/ Protection mode I just pulled my planet audio amps out had two 1500w pushing my 12in sundowns changed amp same wire and all could you spare some word of the wise as soon as possible
this is very easy... the protection shows that the core on the amp won't allow power inside because of a spike that caused your fuses to blow just replace the same fuses and you will be fine... then you can add a 2 Farad capacitor to give the amp more power to overrun the resistance of the subs, the amp heats up because of the resistance you can fix that by tuning into a parallel connection... The amp is perfectly fine, just tune your frequency correctly according to your subs and improvise with your enclosure - that is also for a better bass performance...
Wow!...... sound like you know something! I'm no expert but, is it possible to increase the power of an amplifier?...... with changing the the while board! I have a small Roland guitar amp that is just a bit underpowered for the cafe that I play! I am happy with it most of the time so, I don't want to replace it with something bigger and heavier!.....
That's a bunch of bullshit lol I know late post but I got two 12s can only handle 1200 watts got a 2000 watt amp doesn't need more power your just trying to blow someone else's subs
aww man not another kicker amp, i had an older kicker impulse amp, that i only had 1 sub on it and the sub would go in and out and everytime it would go out the red light came on, and when it does work and i have the bass up, i smell hot audio stuff, not the sub but the amp, took it apart and 3 resistors are burnt to a crisp and someone before me put new tranistors in(cheap ones) and probably why it failed again, along with black parts. poor amp. anyone ever try the jvc amps? lookin at one
All my speakers are working however the amp has gone into protection mode and sub not working I've tried the sub on my bros car fine every time. Not the fucking same without base I'm pissed off now 😡
Theres your problem the damn cap that bullshit aint needed until you git aloot of damn speakers like my4 15s ..do away with the cap check your subs ohms with a meter and i bet you it will work if not your amp is fryed
I just ended up having to replace the amp guys. Good luck!
Im just saying You should have replaced the fuses and check to see if its giving out any Voltage
Replace speaker wires. Check fuses. Make sure your ground is good and check the impedance. You might not have been getting enough voltage. Usually the amp is good when you disconnect speaker wires and it comes out of protection mode
Did the replacement amp fix it?
I repaired one just like it, was in protect due to voltage regulator! These are nice class D amplifiers! But sometimes having the bass boost all the way up is an issue as well! This amp will run on as little as 10V at least factory claims it will handle 10-14V!
lost harness to jenson car sterion main 16 pin vm9311 harness need new one anybody have pic so i know what it looks like vm 9311
I had the same problem. I re wired the subs with a thicker gauge speaker cable. Works great now.
when my soundstream trx 1500 was doin that ,i found out that it was my 12 volt hook up . had to rehook up my 120 amp fuse . that line has to be tight and pulling current.
Check all your cables make sure your ground is not touching paint sand it to the bare metal so it could get better wattage and check your fuse holder!
hey umm what happen to ur amp did u fix it my amp dose the same ting?? i have a ssl force??
Hmmm, Ive had the same problems, try opening up the amp and looking for any burnt out or melted connections, if there are, it definitely is the amp. If not, it could be how you connected it or what you connected it to. 600 watts is a lot and can overdrive some batteries with a small alternator. But that probably isn't it because one, it goes into protection without the subs, and two, you have a capacitor. Also, try lowering the imput volume, doesn't hurt to try.
Hey who is that first song by? Anyone know the artist and name of song? I been trying to find that for years!
I had the same problem until I unhooked the power captor !
What's that?
blown sub. a blown sub can be like taking the + & - and twisting them together. it's called a short. 2ohms is less resistance than 4 ohms etc. so it's like the amp has zero resistance ( zero ohms) no Amp can't handle zero ohms. protection mode it is. any questions?
I got a 6000 watt sound stream tarantula series and a 5000 planet audio doing the same thing
Juan m. I got some t7 tarantula soundstream 12" subwoofers and there good . 800 watts each hooked to a trx 1500 tarantula amp . takes the power and if it does blow ,theres a recone kit available for them .
@motorhead45102 Lol was it a kicker impulse 352xi? or something like that?
I think I may have the same problem at you, did your amp go into protect only at loud volume?
Mine do, why is that
9 times out of 10, amps enter protection mode because you did something your not supposed to. like turning the settings up you high, or running subs that are lower ohms than it rated for
@Silvershredder16 forgot to mention the amp is a 2 channel boss 1000 watt max amp and i brigged the sub connections so their only using 2 of the terminals on the amp for max power
Did u figured out the problem?
your only useing a 1/2 F cap you need a 1 to 2 F cap. for starters then double check all of your connection to make sure that they are making a good connection.
if i turn up the volume to high and my amp getting in protection mode .. so i turn off the head using .. after 5 minutes i can play it again . then got protection mode again .. and you got any issues that would could be??
am a tech on this amps one of the mosfets is bad or cap open it from the back and look for any burn transistor mosfet
Can you message me? Jteale3980@gmail.com
@@teale369 what its your question? About.
hector mendez my amp goes into protect mode and I found a cap that the joints were broken. I resodered them.
What gauge is your wiring harness? Because you dont want to go to big with a small amp because 600 watt amp is to small of an amp for those subs. Im sure thats your problem. The bigger the wire harness the more power your gonna bring to the amp which is gonna put ur amp into protection mode so you dont fry it. You would have to get a bigger amp (1000 watts) if you have 15in subs or (800watts) if you have 12in subs. Or change the wire harness. You should have a 6 or 8 gauge harness with a 600 watt amp!!!! Definitely not a 4 or 0 gauge.
Might have heard that wrong but if you got 2 dual 4ohm your only wiring option s are 4 ohm and 1 ohm
Try to put a bigget fuse I have a boss 1 channel monoblock I was having the same problem but then I checked all my ground wires and power wires and remote wires and the problem was I had to put more stronger fuse so now instead of running 2 25 fuse I decided to put 40 2 40 fuse meaning you have to run 80 and always check your ground wire sometimes if your ground wire is not perfectly tight the way it needs to be tight it's going to make your aunt go to protection mode I hope this advice can help you good luck with your project also try to get a better power wire especially if you're a monoblock the power wire and the ground wire supposed to be some strong thick gauges that way your aunt does not go to protection mode I was looking at your video and I seen your power wires burning like a three or four gauge try using like a zero gauge
You ever figure it out?? Same problem for me as well...
Kevin Reid my amp was just done.
I still have the speakers and they work great still.
Would an compassitor work
I had the same problem with an amp. Got the system tested and they tried a different sub and it was fine. When they took the sub out the coils were black
I have a ssl mono block 5000 when it gets hot it goes in protection what can I do to prevent that
Robert Pearson put 3 fans like computer
Blue led indicator bulb of my pioneer gm d-9601 class-d car amplifier starts to blink & sub woofers produces distorted sound after playing it for more than one hour. Plz let me know what may be the reason for that ?
best way to testturn ever thi ng down on amp meaning gain bass boost then hook up one sub go from there sumtimes amp heatin up thats y they do it or to much power given to the sub or taken
@jairo Martinez I eventually just gave up and bought a new amp. The amp was pretty old anyways. I went to best buy and bought a Polk audio for about $200 I'll upload a new video so you guys can check it out .
Brother if u need amps hmu. Fuck be and all chain stores .pawnshop sukiyaki my did I got best prices brother. I got 3namps right now that range from 300 ton400 bucks for 90bones . Rockford. Jbl. Alpine etc I will hook u up
when two kicker subs that come in a box made by kicker are 4 ohms each and are in that oem box that means you are running 2 ohms with both speakers combined. when you bridged it you might of possibly put them in 1 0hm you must put it back to normal so it can run 2 ohms again as opposed to the setup you have now in this video which based on what youre saying i can asume is 1 ohm
Ok. 1st, is your sub wired 8ohm or 2 ohm final impedances(per sub)? 2nd, if your amp is capable of 1ohm? If I remember correctly, the lowest impedance the old school Kicker amp can go is 2ohm. If it keep going into protection mode, your final impedance on your subs are setup up @ 1ohm, which too low of an impedance for that amp and goes into protection mode. Try removing all speaker cables and run 1 sub, 1 coil and see if it still goes into protection mode. If it still goes into protection mode, something wrong with your amp. Probably a bad output mosfit.
If the amp goes into protection mode could it be a burnt wire or could the amp be fried
It's your amp, i had the same problem, bought a new amp and now it works fine
My amp is a monoblock and I got 3 subs hook up to it. A 1ch amp can run 2 subs, just depend what impedance u running ur subs on and what the lowest amp amp can go.
It was my fuses to my amp 3 40a fuses they looked like they was good but they weren’t!!! Changed they not going into protection mode
Hey bro i have a hifonics on protect mode. So i took it out. Does a protect mode amp mean is no good anymore?
truejey 747 not all the time, I’d check the fuses and your ground wire first
Hey bro I think it's ur capacitor take it off and just wire it normal without it see why happens and and if not go under ur hood check fuse if it not melted er anything tell me if that helps
That's why it goes into protection mode because u have them bridged mine did the same exact thing it goes into protection mode because ur amp is getting too hot because u have them bridged
So how you get it out of protection mode? I have mines bridged and it went into protection mode
Bank Money James same here, did you figure it out?
Turn the Filter off and then see what happens Also turn the Gain all the way Down and if you have a Level nob for volts turn it all the way to the right for the lowest volt setting,and use that seat belt bolt under the back seat too.Grind all the paint off of it and around it.Also get some Subs that you can't blow up no matter how much you turn it up....
I had the same problem. Start your car and when your amp powers on connect your subs while its playing and it'll work
I would try switching Subs I had the same problem with a set of kicker L5
Hi.The fact that subs are disconnect should allow your amp to go off protection.jus switch your radio off and back on.reset.if it's still in protection then it can be a number of faults like loose positive contact on fuse on battery if you have.or it has a internal fault like burnt or faulty mosfets etc.need to remove test and replace by a technician .only then will it come of protection .
@Thekwesi. Idk what happen to the almp but as soon as I replaced it I got back to bumping! I bought a polkaudio amp.
U should try one ground, sometimes there's enough current running from one ground to the other ground
mine does that crap to !!!!!! do you know how to fix that problem ?
Did you fix problem? Cause I did. I changed all wires. Also if you have different guage wires on speakers inside and out have to be the same. Try that and let me know if that worked caused it worked for me.
CHECK THE DECK IF THE CONTROL WIRE IS LOSE THAT WHAT HAPPEND TO ME
I think I have your amp and it is working great
i have the same problem with mine! i got 2 12 inch kickers at 400 watts rms each and 1000 watt amp max. everytime i turn the volume up the subs shut off and the amp goes into protection mode sometimes even does it when the volumes not even loud. i dont know if the amp is bad or i need new wiring but i just need my damn subs to work without shutting off! haha
Didn't do that till you touched the cap check and see if it's tite or not
Check bass knob. I took mine out and it fixed the problem
Mine i just wait till it warms up then it'll start by itself
i have the same problem with the same cables and they told me it should be the fuse box that doesnt have enought capacity for that much power
What fuse were you.running thru ? Lighter fuse?
hey im having the same problem... someone told me my amp is no good... so a got a new amp... worked good for like 3 weeks... and new started going in to protections same as my other one... I notice it my by my sub... I put another one.. and some times it goes into protection... once I turn the car off... and back on than it works again... its obvious I still have a problem.... please someone help
manny diaz I have a problem almost like this. Mine only goes into protection mode while im driving. When I park, turn the radio off and back on it plays with no problem. I JUST DON'T GET IT.
I got it fix all it was is that I had a low voltage fuse
manny diaz which fuse? In the amp, under the hood? Which one? It pissing me off. lol
Under the hood. I had a 70 amps and my amp kept going in to protection or turned off I switch to a 100 amps and problem solved
mine too
Bridged It to makeb Shure wires are in the right spot and then on Bridget's if it goes left and right instead of doing the bridge
have the same problem it's on protection mode how do I take it off??
el compa enrique replace the fuses
What track is playing in the background
A shitty one
WELL I HAD FINNALY FIGUED OUT IT WAS MY AMP!
How much you want for it
@EckoMG13 wat waz the problem cuz i hav d same problem
Got a Targa 2100w and it doesn't wana go off protection mode
I was having same problem I got a 2400 Watt kicker amp was,bumping good n then the subs stopped I thought it was,amp but no I had 1 out of my 2 12 " subs blew I disconnected the blown sub stopped going into protection!!
I have a SSL 5000 watt monoblock why do it gets hot and go on protection
i had same problem the reason why for mines was because o had everything up on my headunit and my amp up soo just tune dwn the headunit Eq see if dat works
What was wrong with the amp
i'm no professional but man, you take in pride in your installation...looks like you just threw it together, just sad
Kevin Scott I got a autotek mean machine 2000w and with no wire but power ground remote and R/cA wires hooked up lights all come on but stay red/ Protection mode I just pulled my planet audio amps out had two 1500w pushing my 12in sundowns changed amp same wire and all could you spare some word of the wise as soon as possible
@34celticpride yes it was a 352xi amp, how did ya know? lol
this is very easy... the protection shows that the core on the amp won't allow power inside because of a spike that caused your fuses to blow just replace the same fuses and you will be fine... then you can add a 2 Farad capacitor to give the amp more power to overrun the resistance of the subs, the amp heats up because of the resistance you can fix that by tuning into a parallel connection... The amp is perfectly fine, just tune your frequency correctly according to your subs and improvise with your enclosure - that is also for a better bass performance...
Raylene Steve De Water doesn't work
Wow!...... sound like you know something! I'm no expert but, is it possible to increase the power of an amplifier?...... with changing the the while board!
I have a small Roland guitar amp that is just a bit underpowered for the cafe that I play! I am happy with it most of the time so, I don't want to replace it with something bigger and heavier!.....
Need a bigger amp. Subs are calling for more power than what that amp can offer
That's a bunch of bullshit lol I know late post but I got two 12s can only handle 1200 watts got a 2000 watt amp doesn't need more power your just trying to blow someone else's subs
thecoolzach1 exactly right bro that's what I was thinking ....
idk_tho try just happen to me changed the amp...no more problems
Try running a negative from the battery,instead of the chassy
Same thing happins to me it doesn't work radio at all
Its either the way u wired subwoofers or they pull too much power from battery. Buy a xs power battery or yellow top and then do an update video
do u still have amp
A bro I'm in the same boat I'm dealing with the problem
aww man not another kicker amp, i had an older kicker impulse amp, that i only had 1 sub on it and the sub would go in and out and everytime it would go out the red light came on, and when it does work and i have the bass up, i smell hot audio stuff, not the sub but the amp, took it apart and 3 resistors are burnt to a crisp and someone before me put new tranistors in(cheap ones) and probably why it failed again, along with black parts. poor amp. anyone ever try the jvc amps? lookin at one
yeah just use thicker cable, I did it and it solved my problem.
Turn your gain half way restart car and you’ll be just fine
@goofyaladin23 yess to much power amp cant handle itt
Your sub cables are weak and also could be making contact with each other
Ya make sure nothing touching but went off wen u took the speakervwure
All my speakers are working however the amp has gone into protection mode and sub not working I've tried the sub on my bros car fine every time. Not the fucking same without base I'm pissed off now 😡
@motorhead45102 Hahaha sadly it was my 1st amp. I know the painnnn
They are pulling too much juice from your battery
Check your battery post it may have corosion on it
now need to save for better subs can anybody refer to any that are 2400 Watt n 1280 rms
ensted of bridge to 2ohm. run only 1channel. it should work
ground cable scrape the paint
it's the wrong ohm load
check your ground
you have a problem with your speaker wire when I'm inside of your box
Blow the amp out to going to be careful when you stripping wires blow it out with compressor
OMFG i have the same box and subs but a 8105d amp and my amp shuts off too the fuck!!!!
Smell it..if ohm load is too low it will fry amp..
I fixed my amp
ur speakers are starting to burn out replace n problem solve
It's your ground
Brother kita El Capicitor . Y vas a washer ke q vole kekis panadero
Theres your problem the damn cap that bullshit aint needed until you git aloot of damn speakers like my4 15s ..do away with the cap check your subs ohms with a meter and i bet you it will work if not your amp is fryed
@Antonp21654 capacitors don't do shit
i found the problem to the answer,you got to run the remote into the power supply on amp
then how do you turn amp on and off
On amp*
To much power going from your subs to your amp. That’s why going into protection mode.
Too much ohm