Stitching Holes for Leather Patterns (CAD)

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 พ.ย. 2024

ความคิดเห็น • 63

  • @journeywithin6274
    @journeywithin6274 3 ปีที่แล้ว +4

    This is one of the most important skill to create a perfect stitching for a professional work instead of guessing. Worth learning. Awesome video ! I wish you can show also your approach to round corner in the future video. Thanks !

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว +2

      Thanks! It gets a bit more complicated with pricking irons around corners but with diamond chisels it is quite straight forward.

  • @jstudios2698
    @jstudios2698 2 ปีที่แล้ว +1

    I don't even use CAD but the principles you're teaching here are very useful! Will try to do the same in illustrator. thank you very much!

    • @TeranAtelier
      @TeranAtelier  2 ปีที่แล้ว

      I am glad you still found it helpful!

  • @randomscandinavian6094
    @randomscandinavian6094 3 ปีที่แล้ว +1

    Very smart use of the protractor. I made my stitches by eye and had to print and adjust several times in order to get the pattern right. Other than that I do everything the same way, only in Adobe Illustrator.
    I’m fascinated by this topic and by the difference between prepunching the holes before glueing vs gluing and then punching. Also cutting everything to size first vs having oversized pieces and then trimming at the end. Both have advantages and disadvantages.

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว +2

      Thanks! I didn't have a real protractor on hand so I downloaded one. I rarely pre-punch single pattern pieces before gluing as it doesn't always align perfectly when gluing. Trimming after gluing saves a lot of sanding time and gives the best looking edges, I try to use that method as much as possible. I am not a fan of pre-punching every piece of a pattern before gluing as it is difficult to get nice clean edges.

    • @randomscandinavian6094
      @randomscandinavian6094 3 ปีที่แล้ว

      What I’m trying this week is to cut one layer to final size first and then have everything else a bit oversized. In the end I trim everything to match the master layer. I change my method a lot as I’m learning. Writing this comment I just had an idea to build a simple clamping jig that holds the work in place under a metal ruler when cutting.
      Thank you for your video and your feedback!

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว +1

      @@randomscandinavian6094 That is a good technique, I use it for watch straps where the inside lining is cut to size and then used as a guide to trim the outer layer.

  • @mgurbulak
    @mgurbulak 3 ปีที่แล้ว

    Amazing video. Thank you so much for your time.

  • @eytanlew
    @eytanlew 3 ปีที่แล้ว

    Another extremely helpful video! Thank you!

  • @GreyWolfLeather
    @GreyWolfLeather 3 ปีที่แล้ว

    Nice video, in addition to copy and pasting the stitch you can use an array function and toss in the number of holes (I estimate then add or remove as necessary) little less work 😉

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว

      Thanks! There are so many ways to space out stitches in CAD. The straight edges are simple whereas the curved edges take a bit more work.

  • @aileen0788
    @aileen0788 3 ปีที่แล้ว

    Great video. Thanks!

  • @ThoughtFission
    @ThoughtFission 3 ปีที่แล้ว

    So useful. Thank you!

  • @2stroketyson79
    @2stroketyson79 3 ปีที่แล้ว

    Thank you my friend

  • @richarddavis6425
    @richarddavis6425 2 ปีที่แล้ว

    good video. Since a year, are there any better approaches for offset paths and stitching hold using AutoCAD LT ?

    • @TeranAtelier
      @TeranAtelier  2 ปีที่แล้ว

      Thanks! The ARRAY function is also useful to place stitches along a stitching line that has been offset from the border. This is very useful for curved edges as the stitches will always be rotated properly with respect to the stitching line.

    • @-JMR-
      @-JMR- 2 ปีที่แล้ว

      @@TeranAtelier what about in Nanocad? I don't think they have the array function

    • @TeranAtelier
      @TeranAtelier  2 ปีที่แล้ว

      @@-JMR- NanoCAD also has the array function. Just type ARRAY and hit enter and a dialog box will come up where you enter the settings. It works very similar to AutoCAD.

  • @mohamedelkhodary3904
    @mohamedelkhodary3904 3 ปีที่แล้ว

    Thanks for all efforts and nice work.
    Would you please explain again the step of (copy with past point) time 3:15 as I didn’t get it, although i tried many many times. how you select the end point and put them in one line after you moved little to left side. Thanks again

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว

      Thanks! For that part I used the copy with base point command and selected a base point 3.38mm to the left of the top of the stitch, then when pasting, the pasted stitch will appear 3.38mm from where I position the cursor. Another method would be to draw in a horizontal line 3.38mm long and then use the normal copy command on that line and and stitch, then paste both of them together, and then remove all the unneeded lines later.

  • @Danilo-ri8gh
    @Danilo-ri8gh ปีที่แล้ว

    Hi! What is the size of the thread you use for 3.38 chisel? I'm just into making leather wallets, and I really liket your stiching size of your wallet at 7:44, looked pretty nice!

    • @TeranAtelier
      @TeranAtelier  ปีที่แล้ว +1

      Thanks! That wallet was 4mm spacing with 0.5mm thread. For 3.38mm chisels I use 0.45-0.6mm threads depending on the look.

  • @redtoy22r
    @redtoy22r 2 ปีที่แล้ว

    Cool video. I use illustrator and make my stitch lines first then offset path to final dimensions. My problem is after I dye my leather I want to change my hardware. As makers we are our worst critic 😏 thanks for your time in making this video.

    • @TeranAtelier
      @TeranAtelier  2 ปีที่แล้ว

      Yes there is always little things that can be improved on. I will try your method starting with the stitching lines.

  • @michaelsmith-ep7jq
    @michaelsmith-ep7jq 3 ปีที่แล้ว

    Oh my aching head. I do it the old fashioned way with pencil and paper. Using 3mm irons makes the math easier. Can that program figure out a curved gusset including the gusset fold that is stitched to the bag body? Keep up the good work.

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว +1

      Thanks! CAD software is very versatile and you can extract the length of any curved line like the outline of a gusset. I haven't tried designing a gusset with a fold but I wouldn't think it would be an issue. I am planning a video making a simple gusset using CAD so you may get some ideas from that.

  • @guardiangroup7205
    @guardiangroup7205 3 ปีที่แล้ว

    Which version of NanoCad did you use? Plus, Pro, Mechanica, Construction, 3DScan or just the NANOCAD?

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว

      I have been using the free version of NanoCAD for all my videos. It is sufficient for working in 2D.

  • @arekieh
    @arekieh 3 ปีที่แล้ว

    Great videos, thank you! What do you recommend for spacing for 2.7mm irons?

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว +1

      Thanks! You can still design the layout so you can get your even stitching spacing but it is hard to get smaller spaced stitches lining up well to a pattern, planning by eye may be a more time effective option. For the pockets you can try overlapping the t-pockets like it did in my Himalayan crocodile card holder video.

  • @LuizmarJunior
    @LuizmarJunior ปีที่แล้ว

    Excellent video, how can I send you a project I made for evaluation? I'm currently using AutoCAD in projects.

    • @TeranAtelier
      @TeranAtelier  ปีที่แล้ว

      Sure! Send me a message in Instagram: @teranatelier

  • @akintomideakintoye8972
    @akintomideakintoye8972 3 ปีที่แล้ว

    Wonderful.

  • @mohamedoueslati933
    @mohamedoueslati933 ปีที่แล้ว

    hey sir ! how can i make them apply to a round shape ? that would be awesome.

    • @TeranAtelier
      @TeranAtelier  ปีที่แล้ว +1

      For curves, use 2-prong pricking irons to preserve the spacing of stitches.

    • @mohamedoueslati933
      @mohamedoueslati933 ปีที่แล้ว

      @@TeranAtelier thanks for your response but i meant in nanocad mr teran

    • @TeranAtelier
      @TeranAtelier  ปีที่แล้ว

      @@mohamedoueslati933 Sorry about that. The way I do it in CAD is to copy and paste circles that have a radius equal to your pricking iron spacing. Paste a new circle center where the circumference intersects the stitching line. The circle centers will then be the centers of your stitching holes. I hope this helps.

  • @usmanmusman7047
    @usmanmusman7047 3 ปีที่แล้ว

    Nice

  • @brucelutz5699
    @brucelutz5699 ปีที่แล้ว

    i took a piece of clear plastic vinyl and punched it , the plastic vinyl is used for covering furniture in the day. now after your leather is marked where y would stich lay plastic on leather and see what to do up or down.Use a punch to witness 1 hole then remove plastic and you should be good to go

  • @keith198120
    @keith198120 2 ปีที่แล้ว

    Is this functionality available in nanocad free?

    • @TeranAtelier
      @TeranAtelier  2 ปีที่แล้ว

      Yes the version of NanoCAD that I used in the video was the free one. It has all the basic functions the same as AutoCAD.

  • @pattyclayton6114
    @pattyclayton6114 7 หลายเดือนก่อน

    I can not download the nanocad software. Is there a trick?

    • @TeranAtelier
      @TeranAtelier  7 หลายเดือนก่อน

      There is a link in the video description and you will need to sign up to be able to download the free version of the software.

  • @senianga1
    @senianga1 27 วันที่ผ่านมา

    Don't you have array function on cad_?

    • @TeranAtelier
      @TeranAtelier  26 วันที่ผ่านมา

      Yes, both NanoCAD and AutoCAD have array functions. However, I tend not to use them for my design work as I like place my stitching holes carefully around corners and where the stitches span over perpendicular leather edges like down the side of card pockets.

  • @mahmutgurell
    @mahmutgurell 3 ปีที่แล้ว

    Hello 3mm french types pricking iron for awl size?

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว

      It would depend on the brand of your pricking irons as they have different prong widths. 3mm is a small stitch so I would go with the small size awl like #0 or #1.

    • @mahmutgurell
      @mahmutgurell 3 ปีที่แล้ว

      @@TeranAtelier my 3mm pricking iron size 1.5mm for awl size 1.4mm vs 1.6mm ?

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว +1

      @@mahmutgurell The difference would be almost unnoticeable but I would go for the 1.6mm.

    • @mahmutgurell
      @mahmutgurell 3 ปีที่แล้ว

      @@TeranAtelier thank you

  • @Mr.JohnnyVLD
    @Mr.JohnnyVLD 3 ปีที่แล้ว

    You should try the ARRAY command. You'll thank me later! ;)

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว +1

      It is a great command, but it doesn't really suit my approach for stitching holes around curves.

    • @Mr.JohnnyVLD
      @Mr.JohnnyVLD 3 ปีที่แล้ว

      @@TeranAtelier yes, for the curves, it's better to go manual, cause array respects the length of the curve and not the length of the straight line between two chisels.

  • @rockyrosatu3401
    @rockyrosatu3401 3 ปีที่แล้ว

    man my screen turn black not white

    • @TeranAtelier
      @TeranAtelier  3 ปีที่แล้ว

      If you are referring to the background color in NanoCAD, got to 'Tools', 'Options', 'Color Settings' and change 'Background' to be white.