I've installed 3 of these. No major issues at all. All 3 went in easily. One of them was in a major accident and the airbag functioned as designed. I am very happy to now have a drivers side grab handle that should have came that way from the factory!
Just installed mine. Got it for Christmas. Been cold in Vermont. Nice weather finally. Took about twenty minutes to install. But, it was second attempt. Used a nut driver this time to get the upper bolt started and mostly tightened. Not too bad. Had to call company up get replacement bolt hole covers as one broke during installation. They seem to be the week part of the package.
That clip was a pain I ended up tapping it in place and utting the hole in the tape I guess it's the angle I saw these well lights for the floor but you have to take that pillar and handle off that's where the dome light wires are and it makes them come on with the door open and stays on until the other lights go off.i always wanted to ask you if the unicorn had a lighted ring around the ignition if you used keys that's a cool little extra even when the lights are on it's dark behind the wheel and that lighted ring keeps me from scratching things when I go out on a dark morning.
I still don't understand and wonder why Toyota decided to have grab handles on all the passenger doors, but NOT on the drivers door! (Handles should be standard on all the doors on a truck!) I'm 6' 1" and can get in the drivers side with no problem. But it's a chore stepping in for the wife, or anyone 5' 4" and under if they need to get in from the drivers side to drive the truck! (even with running boards!) I Love my Taco, but that's a fail on Toyota, in my opinion!
Looks good Rob :-)! Rob I have a question that maybe you might be answer or maybe even run into the same problem. I've got a 2019 3.5 engine extended cab 4 x 4 Tacoma. A while back I tapped the rear bumper of my jeep with the rear bumper of my truck slightly and it collapsed the passenger side bumper there right into the fender. Have you ever run into this before or had Toyota friends and heard this and if so, would you be able to tell me how to fix this, not necessarily in full detail, but basically just what needs to be done. Can I put a hook on it and pull it out? Any information will be greatly appreciated.:-) Thank you, Donna from Hebron Ohio
@@RobMotive Thank you Rob, I really appreciate it. Especially for getting back so quickly. :-) i'll give it a try when the weather warms up a little bit because it would be my luck I'd break the plastic somehowLOL!
Everything on that handle went really well for me even that bracket only took me two attempts my problem was the covers both of them they just kept popping out I finally got so sick of it that I glued them in the tape is a much better idea but I just got disgusted and now it's impossible to get them out and as far as the company goes I got mine in the mail about two weeks after I ordered them then about three month later I got another one and I was charged for it got in touch with them via email and they got right back to right away saying how sorry they where they would send me a new packing slip and credit my debit card well after two weeks no packing slip no nothing 6 attempts to get in touch with them no response finally I sent them back on my own big mistake never got credited and if I hung on to the handles my best friends son bought a brand new pro model I could have given them to him I think I learned my lesson this time rob.
So what happens if or when that air bag deploys due to an accident with that handle and the extra screw installed? I hope it doesn’t become a projectile. Not hating … Just pondering 🤷♂️
Putting it back in was the toughest part for me when I ran a cable for a camera. Took me forever (about 20 minutes or so). Other than that, it seems pretty simple.
BTW, they already have V2 on the site. It uses a rivet gun and rivet nut instead of that clip you had to tape up. Also looks like the little covers now have little tabs to hold them in place when they are not snapped in.
I installed Vled 6k footwell lighting, had to access the same pillar to attach the connection within so all interior lighting work in conjunction. Not much space in there to work with.
V2 is still a ROYAL pain to screw in. Wow. There's no improvement in having to get the angle just right. QUESTION: Even when very tightly installed, do you find the grab handle wiggles a bit (especially compared to the driver's side)?
@@RobMotive I triple checked it and disassembled it so many times. It was flush, but the problem was the A pillar is more flexible (than V2) and that small screw (not a bolt) just can't hold it. I ordered a V1 and just installed it. It actually was much easier than V2 (thanks to your tips), and it's ROCK solid. I love this thing now. I cannot recommend V2. It's just poorly designed. Very happy with my decision to replace V2 with V1. SO much better.
I purchased this last year. The only problem I have had is the caps won't stay in. I love the product but can't stand the fact the caps won't star in. I have even tried double sided tape. They still don't stay in.
Totally off topic but I don’t know how to search for a topic. The steering wheel in my ‘22 doesn’t telescope very much. I have it all the way out and I’m still reaching. My hand positioning on the steering wheel is uncomfortable. Am I the only one that wishes it telescoped further out?
PRO TIP: For those of you having issues threading in the top bolt, it's a minor alignment issue. On my 2019, the original bolt hole was angled too far upwards. To fix this, you can thread in one of the bolts, and then just apply gentle downward pressure to get the hold to angle slightly downwards to match the new handle. It's just thin sheet metal so it's somewhat pliable.
I put this handle to my Tacoma offroad 2019, and same problem thand you close to 15 minutes juste to put this screw.... engineering problem from this product the angle are not good....
There is no mistake at all. I gave the name of the company in the install video. Ya want me to install it for you too? Thumbs down for making assumptions 👎
I've installed 3 of these. No major issues at all. All 3 went in easily. One of them was in a major accident and the airbag functioned as designed. I am very happy to now have a drivers side grab handle that should have came that way from the factory!
Just got mine in the mail today. Can’t wait to put it on tomorrow morning.
Just installed mine. Got it for Christmas. Been cold in Vermont. Nice weather finally. Took about twenty minutes to install. But, it was second attempt. Used a nut driver this time to get the upper bolt started and mostly tightened. Not too bad. Had to call company up get replacement bolt hole covers as one broke during installation. They seem to be the week part of the package.
That clip was a pain I ended up tapping it in place and utting the hole in the tape I guess it's the angle I saw these well lights for the floor but you have to take that pillar and handle off that's where the dome light wires are and it makes them come on with the door open and stays on until the other lights go off.i always wanted to ask you if the unicorn had a lighted ring around the ignition if you used keys that's a cool little extra even when the lights are on it's dark behind the wheel and that lighted ring keeps me from scratching things when I go out on a dark morning.
Great video
Thanks👍
Wouldn't that interfere with the airbag development
Where in Canada can I buy
I still don't understand and wonder why Toyota decided to have grab handles on all the passenger doors, but NOT on the drivers door! (Handles should be standard on all the doors on a truck!) I'm 6' 1" and can get in the drivers side with no problem. But it's a chore stepping in for the wife, or anyone 5' 4" and under if they need to get in from the drivers side to drive the truck! (even with running boards!) I Love my Taco, but that's a fail on Toyota, in my opinion!
Thanks for showing us this product. Wish the dang truck came with it, I don’t like grabbing the steering wheel to pull my old butt into the seat.
Thank you Rob!
Thanks for watching 👍
Looks good Rob :-)!
Rob I have a question that maybe you might be answer or maybe even run into the same problem. I've got a 2019 3.5 engine extended cab 4 x 4 Tacoma. A while back I tapped the rear bumper of my jeep with the rear bumper of my truck slightly and it collapsed the passenger side bumper there right into the fender. Have you ever run into this before or had Toyota friends and heard this and if so, would you be able to tell me how to fix this, not necessarily in full detail, but basically just what needs to be done. Can I put a hook on it and pull it out?
Any information will be greatly appreciated.:-)
Thank you,
Donna from Hebron Ohio
It’s all plastic. You might be able to pull it out🤔
@@RobMotive Thank you Rob, I really appreciate it. Especially for getting back so quickly. :-) i'll give it a try when the weather warms up a little bit because it would be my luck I'd break the plastic somehowLOL!
Definitely wait until it’s really warm👍
How does it affect pillar blind spot?
Depends on your seating position. It lines up with the A-pillar.
Too bad this doesnt come standard on the Tacomas or at least available as an option. Looks good even though it looks like an aggravating install.
I expect it’ll be added to the redesign.
Rob - please help … I bought this same grab handle, and notice that the supplied bolts are not the same length … which bolt is supposed to go where?
Everything on that handle went really well for me even that bracket only took me two attempts my problem was the covers both of them they just kept popping out I finally got so sick of it that I glued them in the tape is a much better idea but I just got disgusted and now it's impossible to get them out and as far as the company goes I got mine in the mail about two weeks after I ordered them then about three month later I got another one and I was charged for it got in touch with them via email and they got right back to right away saying how sorry they where they would send me a new packing slip and credit my debit card well after two weeks no packing slip no nothing 6 attempts to get in touch with them no response finally I sent them back on my own big mistake never got credited and if I hung on to the handles my best friends son bought a brand new pro model I could have given them to him I think I learned my lesson this time rob.
That’s a bummer. Definitely not a good experience !
🤦🏿♂️🤦🏿♂️🤦🏿♂️
KTJO: dubious at best. Where can one find the same grab handle from a different company?
What’s the tundra grab handle much easier to install than the Tacoma?
Much! It was an OEM part though👍
I need one for my truck. I wonder if I can install one since it is a lease vehicle??? I need to check with Toyota.
Yes you just have remove it before you turn it in.
So what happens if or when that air bag deploys due to an accident with that handle and the extra screw installed? I hope it doesn’t become a projectile. Not hating … Just pondering 🤷♂️
Have a look: th-cam.com/video/HMkrQrJQ0lk/w-d-xo.html
Do you have passenger side grab handle for toyota tacoma 2016-2023 ?
Not sure what you mean 🤔
Putting it back in was the toughest part for me when I ran a cable for a camera. Took me forever (about 20 minutes or so). Other than that, it seems pretty simple.
I believe it! Hopefully the next gen will be better!
BTW, they already have V2 on the site. It uses a rivet gun and rivet nut instead of that clip you had to tape up. Also looks like the little covers now have little tabs to hold them in place when they are not snapped in.
That's great! Hopefully an easier install👍
I installed Vled 6k footwell lighting, had to access the same pillar to attach the connection within so all interior lighting work in conjunction. Not much space in there to work with.
Definitely pretty tight!
V2 is still a ROYAL pain to screw in. Wow. There's no improvement in having to get the angle just right. QUESTION: Even when very tightly installed, do you find the grab handle wiggles a bit (especially compared to the driver's side)?
Nope. Mine is solid (V1).
@@RobMotive Good to know but disappointing. If I tighten it anymore I fear I'm going to strip it. The flex is annoying after all that effort.
I’m guessing something is in crooked🤔
@@RobMotive I triple checked it and disassembled it so many times. It was flush, but the problem was the A pillar is more flexible (than V2) and that small screw (not a bolt) just can't hold it. I ordered a V1 and just installed it. It actually was much easier than V2 (thanks to your tips), and it's ROCK solid. I love this thing now.
I cannot recommend V2. It's just poorly designed. Very happy with my decision to replace V2 with V1. SO much better.
Great that yours is now right👍
I've heard the color match is off and the caps don't match the stock grab handle caps. Is this true?
Not on mine.
I purchased this last year. The only problem I have had is the caps won't stay in. I love the product but can't stand the fact the caps won't star in. I have even tried double sided tape. They still don't stay in.
I’d try a small amount of clear silicone👍
@@RobMotive I reached out to the company today about this. I am waiting to hear back from them.
Do u have a link to that company so I can order one?
I do not have a link for them.
@@RobMotive ok thanks 😊
How did you order yours?
From the company website.
@@RobMotive ok thanks , I did a search for a 2019 Tacoma grab handle and it came back saying no results 🤔
How long did you wait to get the part? I just ordered today 9.23.22.
About a week if I recall.
@@RobMotive thanks
P
Yeah That bracket is so tedious...
To say the least!
Totally off topic but I don’t know how to search for a topic. The steering wheel in my ‘22 doesn’t telescope very much. I have it all the way out and I’m still reaching. My hand positioning on the steering wheel is uncomfortable. Am I the only one that wishes it telescoped further out?
Yup, me too. Just a bit more would be good 👍
PRO TIP: For those of you having issues threading in the top bolt, it's a minor alignment issue. On my 2019, the original bolt hole was angled too far upwards. To fix this, you can thread in one of the bolts, and then just apply gentle downward pressure to get the hold to angle slightly downwards to match the new handle. It's just thin sheet metal so it's somewhat pliable.
That would be the last time I use that company.
I guess if they have a smidgeon of Customer Service that's good enough for them but, sorry not good enough for me
I hate crappy customer service. I’m tempted not to even buy from them.
They are the only game in town. No choice if you want one.
I put this handle to my Tacoma offroad 2019, and same problem thand you close to 15 minutes juste to put this screw.... engineering problem from this product the angle are not good....
It’s definitely a challenge 😬
@@RobMotive yes sir...
Guess I was lucky when I installed mine. Angle of the bottom bolt 🔩 was a bit tough but it went in good the third try.
I’d say so!!!!!😬
Cool that you did a take 2 but you have no link to buy it. Thumbs down for that mistake on this video.
There is no mistake at all. I gave the name of the company in the install video. Ya want me to install it for you too? Thumbs down for making assumptions 👎