Thank you for posting this. My master cylinder is failing and this helps greatly. Question- when I go to bleed the system after install, do I also need to bleed the brakes, or will it be sufficient to just bleed the clutch?
Hi, i have changed my vento tdi clutch set with bearing brand is sachs , still the clutch is hard what will be the problem? Should i change slave and master cylinder both to make it soft?
A quick one. I’ve a MK6 Jetta. How do you flush your brake fluid as my car brake pedal stays hard even on a level ground due to hill hold assist system. Is there a work around for pedal method in this type of car? Or you have to use the pressure bleeder ? Thanks in advance.
If the gravity method is not effective then we can use the back-flush method for bleeding the air out of the system, some cars do have a bit of a hard pedal due to hill hold assist , but that's the Nature of some cars
नमस्ते भैया , Volkswagen vento mein left aur right side ke shocker alag alag hote hai ya फिर same part no ke hote hai Left Wale ko right side mein laga sakte hai ?
Thanks for the informative video. Does this needs to be replaced after specific period ? What if it breaks while traveling, can we still drive the car . I have a 10 year old polo and I am curious if I should replace it now or not, I don't have any issues with the clutch till now.
Sir , ideally it should be replaced when you are overhauling the clutch , yes it can break , and same happened with me , but i was near to home so i just started the car in first gear and drove around 3 kms in 1st gear . As i didn't had clutch so i was not able to change gears and can't break as well
The car will be underivable other than short distances to park it somewhere else or put it on a trailer. You will not be able to disengage the clutch. As in, when you push the clutch pedal down, nothing will happen. So unless you can float gears you really only have first gear, and will need to turn the car off to stop.
This happened to me now..car is undrivable..clutch fully pressed..cant put it in gear..the only thing that took me home was the downhill in a mountain..luckily it didnt happen 2 days before driving at night with a baby inside
@@yourDIYneeds - If the connecting rod would have been of steel then this could have been avoided I believe . But it seems most of the manufactures use only the plastic connector rod . Heard few people were able to replace the plastic connecting rod with a steel one , but sure if its worthy to repair it.
Hi sir i have a 2020 polo 1.0tsi 53k driven when I try to put reverse gear it makes noice but every other gears are working proper should I change my clutch
What happened, why no videos from you? Wanted to ask, can I replace the coolant with Shell long life pink coolant for skoda rapid 1.6tdi? Is shell coolant good
Sir , glysantin g30 ( amzn.to/3U3B62y ) , don't go for anything else Sir i am a little stuck in some work , not getting enough time to shoot videos , will get back soon 🙂
Sir thats just hydraulic fluid sharing , nothing more than that , instead of having 2 separate reservoirs for hydraulic fluid , its better to have just one when both systems need the same fluid
amzn.to/3bIWY23 - L handle amzn.to/3Qwdr8q - 19mm socket amzn.to/3SwK87P - 32mm socket amzn.to/3vPTiTb - small sockets and torx These 4 will be sufficient for general services Considering you have a polo which has a 19 mm drain plug
Hey bro can you please answer me a thing recently i have removed my polo 1.2 tdi thermostat valve and it was not easy in my place to find that whole thermostat part so my mechanic suggest me to remove the valve and he make the connection without the valve so now i m wondering is it a good thing to do please help me.
It will effect the engine only in cold climates , engine will now take more time to warm up , and till the time its not warmed up , fuel economy will be compromised , except that everything else will remain the same
@@yourDIYneeds Thank you so much mayyynnn you have clear my doubt and you are doing great job bcoz of you now i can do small services in my home by myself on my polo diesel. Keep making vdos on VAG cars... I don't know about others but your vdos on VAG helped me alot coz you filled us with every single detail you worked and it worked for me 🤩 Keep up the good work mayynnn 🤙🏽💫
Sir every new car needs to get the pollution control certificate after 6 months from date of sale ( in bs4 ) , i guess its 1 year in case of bs6 ( but not sure )
sir, I have a problem after replacing the cylinder, I can't get the clutch, there is air in the system, even with the pump, it can't be aired, what's the problem, can you help, more precisely, the clutch fails when driving all the way
Sir ring to bohot baad ki baat hai Aap ek bar pehle next oil change pe engine flush use kijiye , modern cars ki rings low pressure hoti hai , and carbon deposits ki wajeh se wo stuck ho jati hai kabhi kabhi , jiski wajeh se oil consumption and blowby dono increase ho jate hai , ek bar next oil change pe ek acha flush for 10 mins and fir oil consumption note kijiye , most probably oil consumption or blowby dono hi kam ho jaege and engine bhi thoda sa smooth ho jaega , pehle ki cars me rings high pressure hoti thi islea ye problem nahi hoti thi , but ab fuel economy increase karne ke lie low pressure rings use hoti hai
Bro how to reset airbag light on skoda Laura?? . I just removed the fuse and placed it and the light shown up 😅.. I tried removing battery negative terminal but its not going
Sir , my age aside, if you had seen the video properly then you would have realised , that getting the master cylinder out without pulling the pedal out first is not possible , and you don't need to be a VW tech to realise that , you just need to have a bit of common sense that , if the mounting bracket of master cylinder is bigger than the hole of firewall then its not going to come out from that side , so pulling the pedal out first is the only other option.
Sir its a 2 person job , you have to press the pedal 5-6 times and then stop it at the end position when another person loosens the bleed screw on the slave cylinder, and get it tight , only after getting it tight you can release the pedal . Have to repeat this process 4-5 times And then top-up the hydraulic fluid
don't say that without explaining your method?!? Please could you post a link to any videos showing how to do it. (otherwise people may not quite believe you?)
@@yourDIYneeds ji sir full charge h lekin start nai ho rai h pahli bar jb unlock kiya tha center lock se to unlock nai hui thi but light jal gai thi unlock krne pr jo light jalti h phir bettery nikalne pr band hui thi
Sir bakiyo se clutch thoda da hard to hai hi , but agar jada lag raha hai , to aap brake fluid change karwa lo , and clutch slave cylinder ko bhi ache se flush kar dena , thoda sa farak padega
Suddenly one morning I found my clutch pedal flat to the floor on my Volkswagon Transporter 6 speed manual. I believe it is likely to be a master cylinder or slave cylinder. But first I have to find them! I tried to follow this video, but the Transporter is different. Any tips greatly appreciated! Here is my video: th-cam.com/video/IoL0r3SlgZI/w-d-xo.html This video shows my clutch problem and shows me trying to find the master and slave cylinders.
Cool couldn't find the clutch fluid reservoir didn't know it was with the brake master , thank you , good video 👍
Thank you for posting this. My master cylinder is failing and this helps greatly. Question- when I go to bleed the system after install, do I also need to bleed the brakes, or will it be sufficient to just bleed the clutch?
Ideally you should bleed both of them sir
You don't have to bleed the brake system
Hi, i have changed my vento tdi clutch set with bearing brand is sachs , still the clutch is hard what will be the problem? Should i change slave and master cylinder both to make it soft?
Thank you for making life easy for us
great video dude - loved it
A quick one.
I’ve a MK6 Jetta. How do you flush your brake fluid as my car brake pedal stays hard even on a level ground due to hill hold assist system. Is there a work around for pedal method in this type of car? Or you have to use the pressure bleeder ?
Thanks in advance.
If the gravity method is not effective then we can use the back-flush method for bleeding the air out of the system, some cars do have a bit of a hard pedal due to hill hold assist , but that's the Nature of some cars
नमस्ते भैया ,
Volkswagen vento mein left aur right side ke shocker alag alag hote hai ya फिर same part no ke hote hai
Left Wale ko right side mein laga sakte hai ?
Sir same part no. hai
@@yourDIYneeds thank you
Thanks for the informative video. Does this needs to be replaced after specific period ? What if it breaks while traveling, can we still drive the car . I have a 10 year old polo and I am curious if I should replace it now or not, I don't have any issues with the clutch till now.
Sir , ideally it should be replaced when you are overhauling the clutch , yes it can break , and same happened with me , but i was near to home so i just started the car in first gear and drove around 3 kms in 1st gear . As i didn't had clutch so i was not able to change gears and can't break as well
The car will be underivable other than short distances to park it somewhere else or put it on a trailer. You will not be able to disengage the clutch. As in, when you push the clutch pedal down, nothing will happen. So unless you can float gears you really only have first gear, and will need to turn the car off to stop.
This happened to me now..car is undrivable..clutch fully pressed..cant put it in gear..the only thing that took me home was the downhill in a mountain..luckily it didnt happen 2 days before driving at night with a baby inside
Sadly it is what it is sir, when it happened to me i drove almost 4km in first gear without using brakes .
@@yourDIYneeds - If the connecting rod would have been of steel then this could have been avoided I believe . But it seems most of the manufactures use only the plastic connector rod . Heard few people were able to replace the plastic connecting rod with a steel one , but sure if its worthy to repair it.
Hi sir i have a 2020 polo 1.0tsi 53k driven when I try to put reverse gear it makes noice but every other gears are working proper should I change my clutch
Sir , in some transmission it's an issue, just try to press the clutch pedal twice before engaging the reverse
Do you need to empty the brake fluid when you disconnect the lines ?
Only the reservoir
Currently trying to figure out a problem, 2014 vw jetta TDI. Clutch just sits on the floor board, could it be the clutch cable?
If its a hydraulic clutch then , its the lack of pressure or presence of air in system
Does vw petrol & diesel cars all come with hydraulic clutch system?
Yes sir , almost every one of then now has a hydraulic assisted clutch
@@yourDIYneeds ok thank you
Can you tell me where the saftey clutch switch is located on an 08 Jetta?
What happened, why no videos from you? Wanted to ask, can I replace the coolant with Shell long life pink coolant for skoda rapid 1.6tdi? Is shell coolant good
Sir , glysantin g30 ( amzn.to/3U3B62y ) , don't go for anything else
Sir i am a little stuck in some work , not getting enough time to shoot videos , will get back soon 🙂
which brand should be used to replace master key and how much it costs usually??
Sir there are a lot of options, but hella is the oem
Should slave cylinder also to be replaced along with master cylinder?
Sir these things ideally should be changed along the clutch plate
How about the brakes? As they operate on the same fluid system do they not?
Sir thats just hydraulic fluid sharing , nothing more than that , instead of having 2 separate reservoirs for hydraulic fluid , its better to have just one when both systems need the same fluid
That spring behind the pedal and above, is that what causes the pedal to speak?
Sometimes sir
Hi brother can u tell some must have basic tools for vw car owners? I am thinking to order as sale is going on in amazon and flipkart..
amzn.to/3JxOozN
amzn.to/3bxOlqW
amzn.to/3bx0QTV
amzn.to/3BMmVbM
These all will do 90% of the work on a german car
@@yourDIYneeds Thank u brother👍 Should buy all 4 in the links? Mainly need tools for general servicing..
amzn.to/3bIWY23 - L handle
amzn.to/3Qwdr8q - 19mm socket
amzn.to/3SwK87P - 32mm socket
amzn.to/3vPTiTb - small sockets and torx
These 4 will be sufficient for general services
Considering you have a polo which has a 19 mm drain plug
My VW polo GT TDI doesn't crank. Is it the starter or the battery???
Have to check with a multimeter before saying anything
Hey bro can you please answer me a thing recently i have removed my polo 1.2 tdi thermostat valve and it was not easy in my place to find that whole thermostat part so my mechanic suggest me to remove the valve and he make the connection without the valve so now i m wondering is it a good thing to do please help me.
It will effect the engine only in cold climates , engine will now take more time to warm up , and till the time its not warmed up , fuel economy will be compromised , except that everything else will remain the same
@@yourDIYneeds Thank you so much mayyynnn you have clear my doubt and you are doing great job bcoz of you now i can do small services in my home by myself on my polo diesel. Keep making vdos on VAG cars... I don't know about others but your vdos on VAG helped me alot coz you filled us with every single detail you worked and it worked for me 🤩 Keep up the good work mayynnn 🤙🏽💫
@@yourDIYneeds and till December i will change the thermostat part thanks for the info ✌🏼
How long do you take change it sir ?
15-20 mins
10.5 months old diesel car ka fitness certificate banana jarurai h kya 2027 tk registered h
Sir every new car needs to get the pollution control certificate after 6 months from date of sale ( in bs4 ) , i guess its 1 year in case of bs6 ( but not sure )
hello. do you have video, on how to change gear bush of VW vento 1.2?
Yes sir , its by name of loose gear shifter
Is it located in the same area for a mk5 gti
Yes sir
Sir can we replace 2013 Polo GT TDI headlights with 2017 Poli GT TDI ones?
Yes sir , it can be , as far as my knowledge goes , we just need to swap one wire position in connector
sir, I have a problem after replacing the cylinder, I can't get the clutch, there is air in the system, even with the pump, it can't be aired, what's the problem, can you help, more precisely, the clutch fails when driving all the way
Press the clutch , open the nut while the clutch is still pressed let the air out , close the nut and then release the clutch
safari dicor kitne kms ke baad service karni padti hai plz tell ??
10000 kms or a year , whichever is earlier
@@yourDIYneeds kk . bro kya mujhe safari dicor abhi leni chahiye ya its loo late to buy ??
Sir depends totally upon how it is maintained
@@yourDIYneeds it's 125000 kms driven
If driven well and maintained well , any engine can last , so it all depends upon how it is maintained
Chevrolet beat har 200kms pay half litre m.oil guage se girta hai aur back compressor b hai plz batie kya karen agar ring dalenge ismai to sucess rehe
Sir ring to bohot baad ki baat hai
Aap ek bar pehle next oil change pe engine flush use kijiye , modern cars ki rings low pressure hoti hai , and carbon deposits ki wajeh se wo stuck ho jati hai kabhi kabhi , jiski wajeh se oil consumption and blowby dono increase ho jate hai , ek bar next oil change pe ek acha flush for 10 mins and fir oil consumption note kijiye , most probably oil consumption or blowby dono hi kam ho jaege and engine bhi thoda sa smooth ho jaega , pehle ki cars me rings high pressure hoti thi islea ye problem nahi hoti thi , but ab fuel economy increase karne ke lie low pressure rings use hoti hai
Bro how to reset airbag light on skoda Laura??
. I just removed the fuse and placed it and the light shown up 😅.. I tried removing battery negative terminal but its not going
sir have to clear it through the obd tool
Great. Thanks
I hav also replaced last week
Brother Please make a video on vw Catalytic converter/exhaust cleaning process
Sure sir
Nice one bro
Vry nice sir
Sir safari pe video please 🙏
VW water pump is of which brand sir .
Sir , there are a lot of water pump suppliers , like mayle , but after the make in india , i am not sure who is manufacturing the water pump currently
@@yourDIYneeds I need the made in Australia one .
Sir that totally depends on the available supply
@@yourDIYneeds in outside VW where would I get genuine product that I am asking
Sir have to check , i source all my parts from a trusted supplier
Brother please make a video on O2 Sensor (Lambda Sensor )
Sir certain polo tdi doesn't even have a O² sensor 😅
🔥🔥🔥🔥🔥
Left hand drive theres 2 bolts on top 1 on bottom
@5:49 crushes thumb 🤣
😅
Can someone help me with a 2002 passat, 2.8 v6 clutch master cylinder?
What happened sir ?
Super 👍
You don't need to take the pedal out. VW tech of 30 years
Sir , my age aside, if you had seen the video properly then you would have realised , that getting the master cylinder out without pulling the pedal out first is not possible , and you don't need to be a VW tech to realise that , you just need to have a bit of common sense that , if the mounting bracket of master cylinder is bigger than the hole of firewall then its not going to come out from that side , so pulling the pedal out first is the only other option.
@@yourDIYneedslol this is great. :D
Bruh I need your help how do I bleed my master cylinder? I have a VW Jetta 2.5 5L 5-Speed manual
Sir its a 2 person job , you have to press the pedal 5-6 times and then stop it at the end position when another person loosens the bleed screw on the slave cylinder, and get it tight , only after getting it tight you can release the pedal .
Have to repeat this process 4-5 times
And then top-up the hydraulic fluid
don't say that without explaining your method?!? Please could you post a link to any videos showing how to do it. (otherwise people may not quite believe you?)
You mentioned the difficulty of reaching the top bolt, but didn't mention how to access it... How?
Sir need to twist your arm in odd angles , as that bolt is in such a place where even the camera could not go when its fitted
Sir meri dicor ka center lock work nai kr raha h wairing heat ho rai h
Sir kahi se short hai wiring
@@yourDIYneeds koi soluction btae sir plz help gadi chabi se unlock ho jati h but start nai hoti h light nai aa rai h
Battery check ki aapne ?
@@yourDIYneeds ji sir full charge h lekin start nai ho rai h pahli bar jb unlock kiya tha center lock se to unlock nai hui thi but light jal gai thi unlock krne pr jo light jalti h phir bettery nikalne pr band hui thi
Immobilizer ka issue bhi ho sakta hai , jab ap start karte ho , to self ghumta hai ?
How to remove are
Bhai mera tdi1.5 ka clutch bahit hard hai
Polo highline help me out please
Sir bakiyo se clutch thoda da hard to hai hi , but agar jada lag raha hai , to aap brake fluid change karwa lo , and clutch slave cylinder ko bhi ache se flush kar dena , thoda sa farak padega
@@yourDIYneeds thnx mate
Suddenly one morning I found my clutch pedal flat to the floor on my Volkswagon Transporter 6 speed manual. I believe it is likely to be a master cylinder or slave cylinder. But first I have to find them!
I tried to follow this video, but the Transporter is different. Any tips greatly appreciated! Here is my video: th-cam.com/video/IoL0r3SlgZI/w-d-xo.html
This video shows my clutch problem and shows me trying to find the master and slave cylinders.
5.47 auw ;-)
😅
Biggest lot of bollocks