Great video, this has happened to me before and did again today… I do have a magnet stick like yours but mine was too big to fit. Upon reading the comments I came across something else you mentioned about using a straw. I immediately ran inside to grab one and it came out first try. Thanks again🤙
I'm working on my FE 390 and my oil pump shaft just fell out too..I really don't want to drop the oil pan. I've been trying to fish it out with no luck yet. Which magnet tool did you use and where did you get it from? Some I have are too big and won't fit down the distributor hole. Smaller one doesn't seem strong enough.. Can I try from the oil filter pick up bracket, or oil drain hole? Thank you.
I am not sure where exactly I got it from as I’ve had it for awhile but any auto parts, hardware, or harbor freight should have something that should be small enough to work. It takes some finesse as the magnet will try to stick to the block as you drop it down in the hole. Just be patient and try to re-earth your old operation game skills. If that doesn’t work you can also try using a straw or something similar that fits snugly around the shaft to try to get it that way but don’t push it or it might drop into the pan. Best of luck, you’ll get it just don’t give up!
Ok maybe its the timing on my 89 f150 i wonder if replacing the distributor will fix it. Something popped after i started it and held the starting button down for a long time maybe its the starting solenoid. Would the starting solenoid make the entire power off when it pops and if i put a screwdriver across the solenoid terminals not start either
im rebuilding an '89 302. and i cannot get the distributor to set down all the way. theres like a 1/8" gap before it seats. im thinking its the oil pump drive shaft that might be misaligned. does anyone have thoughts or suggestions?
I'd pull the distributor and confirm that that shaft is seated fully. Getting the hex of the shaft and the proper gear of the distributor can be tedious sometimes so a method that helps is bumping the starter which should help suck the distributor down that last 1/8". Just make sure your timing gear is set right because bumping the starter will bring you off TDC. Best of luck!
@BarnBuiltFabrications in the past I gave just put a socket on the crank bolt and moved it back and forth slightly. it's a little less aggressive than the starter trick
@@smokineaglesrodshop I tried turning it over by hand while pushing down on the distributor. Did two full rotations and still have that 1/8". Also tried turning the oil pump drive shaft by hand multiple times. -,-
![[TH] 2024 PMGC League | Survival Stage วันที่ 1 | PUBG MOBILE Global Championship](http://i.ytimg.com/vi/FVFT-PFwU80/mqdefault.jpg)
Great video, this has happened to me before and did again today… I do have a magnet stick like yours but mine was too big to fit. Upon reading the comments I came across something else you mentioned about using a straw. I immediately ran inside to grab one and it came out first try. Thanks again🤙
Glad you were able to get it with the straw. Definitely not the best design on Ford's part.
I'm working on my FE 390 and my oil pump shaft just fell out too..I really don't want to drop the oil pan. I've been trying to fish it out with no luck yet. Which magnet tool did you use and where did you get it from? Some I have are too big and won't fit down the distributor hole. Smaller one doesn't seem strong enough.. Can I try from the oil filter pick up bracket, or oil drain hole? Thank you.
I am not sure where exactly I got it from as I’ve had it for awhile but any auto parts, hardware, or harbor freight should have something that should be small enough to work. It takes some finesse as the magnet will try to stick to the block as you drop it down in the hole. Just be patient and try to re-earth your old operation game skills. If that doesn’t work you can also try using a straw or something similar that fits snugly around the shaft to try to get it that way but don’t push it or it might drop into the pan. Best of luck, you’ll get it just don’t give up!
Did the rubber hose work to reinstalled the oil pump shaft? What did you use to hold down the shaft to remove the hose? 1980 F150 with 302.
It did. You can use anything that will fit inside of the rubber hose to push the shaft out with such as a small screwdriver or something of the like.
Ok maybe its the timing on my 89 f150 i wonder if replacing the distributor will fix it. Something popped after i started it and held the starting button down for a long time maybe its the starting solenoid. Would the starting solenoid make the entire power off when it pops and if i put a screwdriver across the solenoid terminals not start either
Sounds like you've got a few issues going on there.
Good info!
Glad it was helpful!
Long magnet and time 😂😂😂or pull the pan. Dab of silicone on shaft, insert in dist. and back in it goes. Worked for me numerous times anyway.
That's a good idea. Only concern I would have is getting any of the RTV or silicone in the oil.
@@BarnBuiltFabrications I meant let it dry then install, it's pretty easy and lasts.
im rebuilding an '89 302. and i cannot get the distributor to set down all the way. theres like a 1/8" gap before it seats. im thinking its the oil pump drive shaft that might be misaligned. does anyone have thoughts or suggestions?
I'd pull the distributor and confirm that that shaft is seated fully. Getting the hex of the shaft and the proper gear of the distributor can be tedious sometimes so a method that helps is bumping the starter which should help suck the distributor down that last 1/8". Just make sure your timing gear is set right because bumping the starter will bring you off TDC. Best of luck!
@BarnBuiltFabrications in the past I gave just put a socket on the crank bolt and moved it back and forth slightly. it's a little less aggressive than the starter trick
@@smokineaglesrodshop I tried turning it over by hand while pushing down on the distributor. Did two full rotations and still have that 1/8". Also tried turning the oil pump drive shaft by hand multiple times. -,-