Power testing 3d printed parts on the Diy Electric Surfboard
ฝัง
- เผยแพร่เมื่อ 22 ก.ค. 2024
- I am power testing 3d printed parts on the diy electric surfboard.After 3d printing some upgraded parts on the creality ender3 v3 ke 3d printer its time to test the electric surfboard in the water to see if i can feel a difference in power.As you will see in the video i have a problem that needs an answer from you guys.
Thanks The Waysider.
Printer Playlist link.
• Creality ender 3 v3 KE...
Electric Surfboard Making Playlist Link.
• How to make a Diy twin...
Music Channel Link.
/ @thesession06 - แนวปฏิบัติและการใช้ชีวิต
On pins and needles ……can’t wait to see you get this thing perfected!…that way I can copy you 😜👍…great work!
Ok my friend cheers
Great video again, board looks amazing, thanks for sharing.
The stop/start at higher revs could be just succing air into the drives and/or cavitaion. To get up and planing I think you will need a minimum of 5kw but preferably 10kw. Higher voltage is more dangerous but 50v should be fine and reduces the current and heat.
Cool cheers. If it is cavitation how would I solve it ? I re made the impellers to try and eliminate any issues with that but when I change some settings in the esc's it can get slightly better but still there all the same. Well either way I need bigger esc,s to up the voltage. Thanks for the comment.
Amazing job and amazing board , design and solution all the way 😊
Nice video and realy nice work!
But , the engine it totaly wrong in my opinion. They or esc will burn 🔥
Must uppgrade and your amazing board will be stunning 👍
Also save money to use low cost ”china” engine/ esc in long term .
Otherwise, stunning board 👏👏
Thank you very much!
Doing my own with similar stuff, except the longer motors,
I'd say you'll need at least 35v, The motor spins 45k at 90v, så 45v gives you apporx 22.5k
22v will only give you 11k rpm with no load. 64-68mm prop will need high rpm, approx 14-18 :)
So do as i do, put them im series so you get approx 10mah 44,4v, and you wont have issues..
except if the ESC can handle that tho
Hi cheers I need to buy better esc then I will put the lipo in series and check the difference. Thanks for the info.
That looks awesome. How come the low voltage? I mean from what I can see, you aren't getting more than over a kw given that voltage. How about pumping it up with a high power 12s battery pack (keeping charge below 50v for safety) but then you would get 50v x 45 amps and thats 2.25 kw. That would pump you much better forward. Im currently posting my 6kwh battery build and my 3D printed carbon fiber 20 kw outboard - would love to get your feedback. I really like how you made those pumps, they look damn amazing!
Hey dude I just bought two new esc's 300amp 14s so now I can go 12s will try 6s but I have the option. Next video I will show you what I've been up too and thanks for the info am glad to help if you have any questions in the future. It's a learning curve but a fun one 👍
@@thewaysider7774 indeed it is fun :) two 300A escs... Jesus. That would allow for 30kw at 50v. Does your batteries, motors, and cables hold up to that? Wouldn't 100A +120A peak be enough?
@@NavalTechTinkerer As far as i understand the more the better when it comes to amps but keeping the weight down as much as possible.i should be getting no more than 150-180amps or so per side, the other thing is that the 200amp-250 esc's i have looked at don't let me use 12s so i went with the one's the guy had that was also not far from where i live, they are the ztw g2 300amp 14s so room to grow if needed i just want to get rid of that stutter at full throttle. and have upgraded all connections to the Qs10 connector's much bigger than the xt 90. i will show it all in the next video.
@@thewaysider7774 cool - any reason you did not go with the flipsky vesc over the G2?
@@NavalTechTinkerer not really i just know more about esc's from modeling and the time it takes to get the things. the shop had the g2 so i went for those i guess it can only improve things over the generic cheap one's i was using. i am testing soon in the river so fingers crossed.
How can i contact tou?
Hi my email adress is on my youtube front page under more/show email under my channel art. you can email me there and then i can share my number.