check the abs sensor. Even though it sits behind the wheel hub, when you pull out the hub it is possible to damage it. I almost broke mine. It was bent. I carefully straightened it out and put it back in.
If your sensor looks good (you can see it in the video with the hub removed) and isnt bent or torn, it could be the hub. Inside the hub is a magnet and the sensor picks up this magnet as it revolves. anyway, check your sensor. I think...there is one in the front and one in the back, both on the driver's side
hello, i am upgrading the brakes on my 2008is250awd, i bought the gs350 awd front caliper, so can the 2008 gs350awd brake discs be installed? I know that the wheel hub of gs and is is the same.
If wheel hub is same size, possible that the caliper will also fit, but cannot be fully certain. You have to check somewhere. Diameter, width and even bolt hole placement on the caller can be different. No guarantees
@@phyinc4506 i just replaced my hubs. First time since I have owned the car. That, along with new tires and new rotors has made the car drive like new. Feels great.
Was your car shaking / vibrating when coming to a stop? Im trying to figure out whats wrong with mine. Its not the breaking system i replaced the rotor and breaks a few months ago.. I was thinking maybe an alignment or shockes. My tires are wearing king of funny
Uneven tire wear on my car - I was getting a bit of the shake when braking. Changed rotors twice, thinking it was them and not my 18 month old tires. Turned out the tires needed to be changed. Changed tires and aligned the car- problem gone.
There are torque spec's for both the (4) wheel hub bolts and the (1) spidle/hub bolt (the 30mm socket). Make sure you tighten properly.
32mm 12pt socket for the axle nut (217ft-lbs)
21mm for the lugs (76 ft-lbs)
17mm for the caliper bolts (100 ft-lbs)
17mm for the hub bolts
you can stick a screwdriver in one of the two holes of the rotor and it will pop right out. Dont drop the rotor :)
Did you have a problem with the ABS, Traction Control, and AWD system after the job was done? I had these light up after doing the same thing.
check the abs sensor. Even though it sits behind the wheel hub, when you pull out the hub it is possible to damage it. I almost broke mine. It was bent. I carefully straightened it out and put it back in.
If your sensor looks good (you can see it in the video with the hub removed) and isnt bent or torn, it could be the hub. Inside the hub is a magnet and the sensor picks up this magnet as it revolves. anyway, check your sensor. I think...there is one in the front and one in the back, both on the driver's side
hello, i am upgrading the brakes on my 2008is250awd, i bought the gs350 awd front caliper, so can the 2008 gs350awd brake discs be installed? I know that the wheel hub of gs and is is the same.
If wheel hub is same size, possible that the caliper will also fit, but cannot be fully certain. You have to check somewhere. Diameter, width and even bolt hole placement on the caller can be different. No guarantees
@@landedinlukla The wheel hub and caliper screw locations are the same.
Where did you get your wheel bearing?
I bought the whole wheel hub. MOOG. Cost about 150 per wheel hub. RockAuto, I think
@@landedinlukla How has it held up? I need to replace it on my GS
@@phyinc4506 i just replaced my hubs. First time since I have owned the car. That, along with new tires and new rotors has made the car drive like new. Feels great.
What made u change the wheel bearing mine has a noise I thought it was the tires but changed the tires around and noise is there still
@@themacintheacc1366sounds like road noise but gets worse. Usually described as a growling or whining noise
Nice job , bro .
Was your car shaking / vibrating when coming to a stop? Im trying to figure out whats wrong with mine. Its not the breaking system i replaced the rotor and breaks a few months ago.. I was thinking maybe an alignment or shockes. My tires are wearing king of funny
Uneven tire wear on my car - I was getting a bit of the shake when braking. Changed rotors twice, thinking it was them and not my 18 month old tires. Turned out the tires needed to be changed. Changed tires and aligned the car- problem gone.
Where did you get that tool that pulled it off
Rented. Any auto parts store will have one. Just ask for a slide hammer.
How many miles did you have when you replaced yours?
A bit over 70k
Dang me too, I’m at 69k and some change but front left. Did I hear you went with Moog?
Moog. I am now at 116k and no issues thus far
Did this guy properly torque the four bolts and the axle nut to the right spec? I don't think so.
This guy don’t torque shit he only go by half a inch brake calipers bolts probably same just tight it to a half inch
Just out of curiosity, how many miles did you get out of your first bearing?Mine needed changed at 100k.
Around 72-80. I don't recall precisely. But def not 100