Yo!! Thank you so much I believe this pertains to 2000s and up rwd for this style mount saved my driveline with this worked for a 06 SWB 1500 used a iron plate that was plenty wide enough to lift came right up even re-alligned my exhaust to where it is supposed to be much obliged!
Man I have been beating my head trying too figure out why my truck was shacking checked my trans mount it's broke in the front cus my check engine light want on so I was like wtf checked it mines cracked thank u I willing to bet that's my problem
@@AaronHinesAuto I have been trying to track down a similar issue with my l460e in my 14 4x4 sierra. I have a vodeo kimicing the noise shifting. Usually once its warm its noticeable.
Did you ever find out what it was? Im currently having this issue, 2015 silverado 5.3 4x4 clacking noise when creeping in 1st gear. In rhythm with the idle. @TuneInBurnOutTV
@@ShawnS.41405 yeah i was thinking you didn't need to remove the xmember on the 99-06. I'm gonna use 2 steel plates and washers bc my poly replacement mount broke after 3yrs. My crossmember Is warped around the bolthole
Great video, no fluff just meat and potatoes
Bro…perfect narrating over the work you were doing. Especially the part about the wood!!!! Thanks man!
3 years out of a trans mount, wow. And it doesn’t even plow. Thanks for another great video!
ya no kidding! thanks for the kind words! and thank for watching
your video really helps, thank you
Thank you. I might as well replace this mount while replacing the driver side engine mount
My car is 2014 Chevy Suburban LT 1500 2WD Rear
I just did my Tahoe’s engine mount. How did you fair with that job.
Thank u ...its really informative...keep the good work....God Bless!!!!
Yo!! Thank you so much I believe this pertains to 2000s and up rwd for this style mount saved my driveline with this worked for a 06 SWB 1500 used a iron plate that was plenty wide enough to lift came right up even re-alligned my exhaust to where it is supposed to be much obliged!
What was the truck doing before replacing??
I have a 2014 Sierra 1500 and when I slow down to about 10mph it jerks and it shifts a little hard
Hey man I am 3 years late but my truck is doing the exact thing what did you do to fix it
Thank you!
Your welcome!
Great video
Was there any viabrations caused from the bad mount?
Shaking on the hwy or anything
yes high way speeds and upon shifting.
What do you mean the after market part doesn’t work the same?
What usually causes the trans mount to break? I watched your vid and replaced mine but am wondering if I could have done something to prevent it?
Wear and tear
Does anyone have the torque spec for the nut that goes through the crossmember? Mine has come loose twice now, I get a squeak each time.
Is the Gmc 2008 Sierra that same way to change the mount ?
Hey bro when you're putting on the motor mounts and the transmission one is it better doing it one by one
Oh yea one at a time using a jack and block of wood carefully at the minimum!
Man I have been beating my head trying too figure out why my truck was shacking checked my trans mount it's broke in the front cus my check engine light want on so I was like wtf checked it mines cracked thank u I willing to bet that's my problem
Ho w did you know it was bad? What symptoms? Trans slop a stop and go?
yes, stop and go slop and heavy thud when downshifting to pass
@@AaronHinesAuto I have been trying to track down a similar issue with my l460e in my 14 4x4 sierra. I have a vodeo kimicing the noise shifting. Usually once its warm its noticeable.
Mine was a sqeek!!
Did you ever find out what it was? Im currently having this issue, 2015 silverado 5.3 4x4 clacking noise when creeping in 1st gear. In rhythm with the idle. @TuneInBurnOutTV
The 2003 Sierra manual transmission does not have enough room to lift.
The crossmember has to be removed.
That’s a bummer. this video is for This video is for 2014+
Molly you jack up the transmission just enough to get the old transmission mount out and put the new one in and let the jack down
@@ShawnS.41405 yeah i was thinking you didn't need to remove the xmember on the 99-06.
I'm gonna use 2 steel plates and washers bc my poly replacement mount broke after 3yrs. My crossmember Is warped around the bolthole
Yeah ! The ratchet works better ;)
Thank you!