How to make Phone charger 12v To 5v | 8A High Power | 6-30V in out 5V 8A
ฝัง
- เผยแพร่เมื่อ 4 พ.ย. 2020
- Hi Friends
in this video i will make a phone charger or 5V Regulator using LM7805 Regulator and TIP3055 NPN Bipolar transistor LM7805 regulator only can give 500ma or 0.5A
of current so we will use TIP3055 transistor to boost the ampere TIP3055 can give 10A but in my circuit its 8A some how my circuit can out 4.5V but it working on 5V devices without any problem don't worry because its 8A it will not destroy your phone because its not always give 8A when your phone need 2A it will give 2A and of it need 1A it will give 1A........
thanks friends 😉
have a nice day
Tags
#Charger
#5V
#12V To 5V
#How to make phone charger
#Charger for phone - วิทยาศาสตร์และเทคโนโลยี
7:34 (A Test)
5:28 (V Test)
Test!
The output sort circuit ampere
Is 7.31A @ 4.5V 😊
8A 😵
OMG
@Creative for you Why have u connected 1k resistor with ground to emitter of tip 3055
@@muralikrishna1504
Its called load resistance
If you Don't use it the voltage will not be stable 5V
@@Electronic_For_You thanks I'll search for more info abt it
Thanks for watching 😘
Have a nice Day 👌
Good bro
Thank You very much bro❤️
Nice high ampere
Good job bro 🕶️
Wellcome 😌
Thank you 😀
Woooow
♥️
Hello mr.
the chips become very hot 100 c
what can be used to get it cool, I want to use it for esp32 with wled 5v need 5 amp, going to put this on my motorcycle hoping for an answer thanks
You can use heatsink, and better if you use a buck converter
Wow great work 😍💥💥💥❤️
Thank you 💪
Good bhai aap k video bahut achha h lekin subscribe kam hai me aap ko full spt kruga
Thank you so much for your support bro ❤️❤️❤️❤️❤️
Transistor ke base mein koi resistor nahi hai toh kya isse transistor aur regulator ic overheat nahi hoga jab jada ampere liya jayega ?
yeas... Its better to use 10 ohm resistance, at base
What is your input source and it's vot&....?
Its
12V at 8A input
I used 12V 10A smps
Is it possible to increase the amp of lm2596? just like this one🙂
Maybe 🤔
@@Electronic_For_You I found a video, but the resolution is low. You can try .
Ok I will try 😅
Rangkaian yang berguna kalo mati lampu hp jadi cepat penuh😅
Hello sir 5volt 8amp current deta hai
Yeas
But at 8A Transistor need large heat sink and air blow out
I recommend to use it at 5A 😊
Because it is a liner power supply
Thanks for watching ❤️
Can i use TIP120 instead of TIP3055
Yeas
But you will get lower amp
Can we make 12v/3A out put Module
Yeas Use Heat sink and 7812 Regulator
Welcome
And don't forget to Like and Subscribe 🥰 for new videos
I think u measure the current the wrong way. Current need to be measured in series. Correct me if im wrong. Cheers
No you are right .
But i have measured short circuit current 😊
Sir I connect it 12 v , 1 Amper then how many current is in output?
5V 1A output
Thank you sir 😊
im trying it .output just 4,5v ... not 5v .. why ????
i need 5v
No
Problem 😊
4.5V is Enough For
5V devices
it this compatible in android phone
Yes......!
Be sure to put the wire
Right way
Tip 3055 transistor price?????
I Have purchased from local store and it costs 0.4$ per Piece
how to use it with potensio 50k? for adjustable..
Yeas
th-cam.com/video/zeBjzbADZ80/w-d-xo.html
@@Electronic_For_You yes
Yeas
Hello, can we add 2 capacitors on the assembly if yes (or) and what value please
You should use 36V 1000uf capacitors
@@Electronic_For_You
Ok than you 25v 2200uf is that enough but where do we put them?
You should put it on output!
@@Electronic_For_You
Ok just one then at the exit
Yeas
Can I use 2sa 1943?
No it's pnp
Please what is the amps input
If you give anything input the output ampre will be the same but voltage decrease
May i convert 12 volt to 9volt 8 amp by this circuit?
I recommend XL4016
May I convert 12 volt to 8volt 3am by this circuit thxx
Use 8V IC Named
LM7809 ic , output will be 8V 3A use Good heatsink
sir, is it really true that the result is 8 amperes? 😲 I plan to make it for my bluetooth speaker, so it can charge faster 😊
8A is for peak 😊
But 2-3A works best with heatsink
@@Electronic_For_You Can I also put a 0.1 ceramic capacitor on it to make the output current clean?
Output current is already clean because this is a liner Powersupply . So output is already clean
what was the value of the input current
Same as output current
...
How many ohms the resistor has
Which one?
@@Electronic_For_You you showed it at 2 min 14 sec
@@sunithapadegal8770 you could decode its value by its body colors
Maybe its too hard for him 🫡
resister??
Big one??
Should we use a heat sink or no need
Do not Use without heatsink
@@Electronic_For_You but you used without heat sink how did it work
@@Electronic_For_You but you used without heat sink how did it work
i used for just short time
No heating if you use long time definitely use heatsink
@@Electronic_For_You ok thanks
This is safe or not? Can i charge smartphone it will damage or not to phone
I recommend a buck converter for changing phones ,
Can we convert 18v 4.7m amps to 8v 500m amps??
You can convert 18v to 8v but Ampre need to be same
@@Electronic_For_You can't we decrease the resistance and increase the amp
Not
This is not a buck converter.
why u conneced a resistor from
ground to emitter...?
To stabilize the output voltage!
Right 👍
Can I use this for charging mobile ??
Yes ,
But if something went wrong, the phone can be damaged
Sir I use the circuit my bike battery 🔋(use for mobile charger)?
Yeas
But be careful not connect anything wrong
@@Electronic_For_You it's 💯 safe or not?
Sir please reply
I try?
Its better to not use regularly.....!
Better for Emergency porpoises
What is the value of input amp
5A With heatsink
@@Electronic_For_You input 1 amp what is the output amp
700ma-800ma
Could you make amp booster
Coming soon
Be sure to subscribe 😊
7805 to change 7812 work 8a output
Yeas
And also use more transistor
@@Electronic_For_You thank you bro
Welcome 😊
I want to try this sir . Can i have the schematic diagram?
Its Very Simple Connection 😊
this why I not created any diagram
Just follow Connections
Why you charged Button phone??
Not a smart phone???? 😕
Because i have only 1 Smart phone and used it to recording 😃
@@Electronic_For_You
😅
Can it convert 12 v 0.5 amp to 5 v 1 amp?
It cannot increase amp
@@Electronic_For_You how cand do that then?
You need a buck Converter
@@Electronic_For_You can pliz make vedio on it
I did watch buck Converter review
resistor 1k?
Yeas
But what is that Little capacitor?
Its 1k resistance
Bro jis number da smaan use hoya oh number v mantion karya karo vid ch clear ni aa
Ok 😊
That's not how you test current in a circuit. Meter has to be in series.
How to make 5v to
1.5v,2ampere
Ok 👌
Sir can I use this in my bick to charge smartphone
Is it totally safe?
I recommend Buckconverter
You labelled 8 Amp but you have not shown in video.
7:35
8A See it in multimeter
can you do 6 ..~ 58 volt input // output circuit 12 or 48 Volt 10 AMPERE 🙂 please
For that much power you need to use a buck converter
Sir, if I connect it with a 12 volt 20 amp. Power supply. How much amp will I get from it?
5 Amps
I recommend using 2 transistor
You better put some heatsink on the voltage regulator or it may overheat especially with that high current
At 20A it will explode!
How to get 9v 3/4/5/a
Use XL4016
@@Electronic_For_You plz make connection diagram 😢
Brother i recommend to use a cheap buck converter because this circuit heatup very quickly 🤷
Ampere to thik hai lekin battery presentage nahi badhta hai, kyon
Sorry
I didn't understand 😊
Is phone charger ko ac 220v par kaise lgayen
First you need
220v to 6v or 9 v adeptor then connect it input
no 8amp 1amp out
Maybe your transistors are not original
Boot hy
Ye kya bhai kyo murkh bna rhe ho amp ko parallel mai kaise measure karte hai? And agar 8 amp deta hai to itni patli si wire lgai hai vo to aise hi jal Jay gi logo ko to bevkuf smaza amp to series mai measure karte hai na ki parallel me🤬😡😤
8A is shortcut current
So i didn't use any resistor or something for load
Why 4.5V???
Not 5V????
Don't worry 5V device will work with 4.5V
@@Electronic_For_You
Ohh 😅
@@user-mn3th7fx2y there will be 0.5 to 0.7volt drop across the base and emitter pin of tip 3055
@@muralikrishna1504
🙃 Thanks my friend 😁
But can i use other transistor??
TiP3055 are Expansive and i don't need 8A 3A will also work
You can use MJE3055 they are cheap but handle 10A