Setting Up iNav Servos By Sheer Persistance and No Skill
ฝัง
- เผยแพร่เมื่อ 27 ก.ค. 2018
- Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: www.fpvknowitall.com/ultimate...
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: www.fpvknowitall.com/support-me/
---
Well, we figured it out. Through sheer persistence. You're not gonna learn much today...
![แฟนแนวใด๋ - ยูริ โตเกียวมิวสิค [OFFICIAL MUSIC VIDEO ]](http://i.ytimg.com/vi/4_XVMuhhbsU/mqdefault.jpg)
Could you do a video on setting up servos in betaflight now? Love your work joshua, keep it up.
Would love to see you do some more iNav stuff - fixed wing and autonomous flight is a nice/fun changeup from FPV free style!
Aha good work josh! James didn’t seem as amused as you though😂 I definitely was as amused:)
Here's what I found helpful.
In the "Servos" Tab:
If they go reverse, change "Direction and rate" from +100 to -100
If they exceed maximum wanted deflection reduce min/max
If control surfaces is not perfectly centered adjust servo midpoint. (This is after setting them up as close as possible mechanically )
Note: In the Servos tab servos are counted from 0-7 while in the Motors tab they run from 1-8.
Hope this is helpful.
Need servos on my fixed wing. Thanks for making this!
Thanks Josh! Wish this was out 2 days ago though! lol
Was working out how to get servos working in BF3.4 for a new invention of mine. ;) More to come... :D
This comes at a great time. I'm currently setting up a 7-inch quadcopter but I would like to add a gimbal to.
Really interesting!!!
Ah disappointed, I thought you'd finally seen the light and decided to get into fixed wing too!
Fixed wing can not auto land. It can not become mass product for the surveillance state tool. Hence, there is no money to be made in fixed wing.
I always need to use "Servo Tilt" to get my beeper that's mounted on the PDB working.
You're right, it's quite complicated to setup, I couldn't just explain it to my buddy.
I hooked up only the signal wire to a motor pad and played around with remapping and all... It's a hassle.
This is exactly what I have been trying to do.
Hey Joshua, I'm struggling to set up a servo gimbal in betaflight on my Matek F405 STD board. Let me know if you can help.
I just saw this I’m trying to do same thing but how do you connect servo to FC do you add the signal wire to uart then how do you add the servo to a switch in OpenTx. I’m using a crossfire nano RX how do you set up a switch to operate PWM SERVO my fc is on a quad not a wing.
YOU ROCK man
A year ago I tried setting up a servo using a naze32, to control a 3axis gimbal. Eventually I gave up. The naze was a terrible decision, and then my gimbal just decided to stop working, so the project was dead. Maybe now I can revisit the issue, since betaflight and f4boards are much better at handling pwm outputs.
I wonder if I could use two or even more servos with Betaflight and still use DSHOT for motors.
Joshua could you explain how to setup a servo for tricopter tail motor on inav?
So true man half the stupid crap that happens with this quad crap I feel alienated from, so I ask you or someone who would know the answer, but before I receive a reply I often fix it myself leaving me feel stupid for asking lol
Hey that’s me haha thanks for the help josh
I just fly fixed wing recently. And it is give me headache to get the servo working.
Thanks JB for your video! If I want install an FC without channel output (span pro f4) on a single motor wing...in your opinion how can I use motor output 2 and 3 (or 3 and 4) for the servos? Can I tab resource on CLI, copy the ports on servos 1 and 2 to motor 2 and 3 resource? That all? Thanks in advance. Sorry if is not clear.
It is possible to map outputs to servos, but as you can see in this video, It's challenging to do. In Betaflight, it may not work at all. In later versions of iNav, it's actually easier than you see here.
@@JoshuaBardwellthen I have to play with Inav. 👍
@@robboape8532 @Joshua Bardwell Were you able to get this working? I've got a single motor Bixler that I'm using a Kakute F4 with INAV and trying to use motor pad 1 for motor and then pads 2,3,4 for servo output. I've got heavy jitter from my servo and burnt one out already but I do have "control" in the output tab. I speculated it was from the ESC refresh rate being at 400hz and the servo being 50hz so after replacing the servo in the plane, I dropped the ESC refresh to 50hz and still have the servo jitter and immediate heat from it. Currently I'm stumped and searching every forum and video for any additional information on the subject. lol Cheers from California :D
the quickest is to remove half of all first. if it stops, its one of the ones you turned off. if not, its one of the ones you didnt, etc. sorting stuff is fun!
I need to set up a 12 Ch out of a TBS Rx through a flight controller on a 2400 Ranger HELP
PLEASE. DJI FPV Head-tracker. I would like to set up crow, full span and all the bells and whistles for a GLIDER set up
Just built my first wing & could have done with this vid a couple of weeks ago. Servos 1+2 on ch 3+4,but they're on 4+5.
I want to use a single servo on BetaFlight for FPV camera tilt up & down that is controlled by the gyro. Any idea how that's done? I've tried watching many other TH-cam videos to figure this out with no success.
Feature servo_tilt will do this, although there is more setup than just enabling that feature.
github.com/betaflight/betaflight/wiki/Servos-&-SERVO_TILT-for-3.1
Hi Joshua Having a problem connecting in INAV. i have flashed the correct firmware , i am connected to com8, selected my board and latest INAV issue, but won't connect to the confiurator, it times out after 10 seconds, Any ideas or advice would be very welcome
If you just flashed the board and now you can't connect, the most likely cause is that you accidentally selected the wrong board type ("target") when you flashed. The fix is to re-flash using the correct target. Before you flash, I always advise going to the CLI and typing "version". This will show you what target is on your board and make sure you flash the right one.
A slightly faster method than removing one at a time would be to remove half, then repeat until you get just one. Good troubleshooting though guys.
Are the servo settings in this video the same as the servo settings in inav Version 7.1 or later? I have a Runcam Mini FVP Dvr, which has a pin for the on/off button, namely the H/L pin. so can I use the servo Pin where I use a flight controller, Speedybeey F405 V3. where there are empty pins, namely: Pins M5, M6, M7, M8, TEL, S9, SBUS. If all the pins can be used for the on/off button via the settings in Inav 7.1, is it programmed by setting the servo settings? a little information, my Runcam Mini DVR can only record 5 minutes. and I have used all the buttons on my remote. Can I use the Arming button for switch button settings in the DVR recording mode that I have?
Check my medlin gimbal video for an example of setting up servos on 7.1
@@JoshuaBardwell Sorry, uncle, what minute should I watch gimbal Medlin's video, or is it on the playlist? First of all, I apologize because I don't understand what a Medlin gimbal video is?
You can search google for, "joshua bardwell medlin" and the very first search result will be the video I am talking about. There is a chapter in that video about setting up servos. Here is a direct link: www.google.com/search?q=joshua+bardwell+medlin&rlz=1C1RXQR_enUS1101US1101&oq=joshua+bardwell+medlin&gs_lcrp=EgZjaHJvbWUyBggAEEUYOTIICAEQRRgnGDsyCggCEAAYgAQYogQyCggDEAAYgAQYogQyCggEEAAYgAQYogTSAQgyNTM3ajBqN6gCALACAA&sourceid=chrome&ie=UTF-8
iNav 2.0 has a much better servo layout.
Inaz 2.0 does have a better set up but i can't get 100% movement when the gyro is activated by pitch or roll movement.
It's easy but different. I've tried servos on betaflight with no luck and yes I know about pin mapping And resource mapping and mixers. I couldn't get the servos to show on the motors tab nor get output and do not know why.
Inav devs decided not to use resource mapping like betaflight because it's too easy to have timer conflicts and they didn't want complaints and wasted time responding to users. So they alot 2 outputs for motors and servos are numbered according to the motor pin numbers. They don't call them servo pins. Unfortunately I'd you happen to have motor outputs on the same base timer other than 1 and 2 then you might have to set the motor to pwm and use the same frequency for both.
Difficult to fly planes and vings without servo'es. Quads is not the only product in the hobby :-)
lol I've never even touched a real servo.
Unrelated topic, but I downloaded betaflight recently on a new laptop and forgot to download the drivers but it still works. Only realized I didn’t download the drivers until after. Anyone else experience this?
rory oconnell I have one even stranger......I put Betaflight on a new computer and forgot to install the drivers.......it connected fine to one of my quads .........but another quad I have it wouldn’t connect to 🤔......had me at a serious loss because I had forgotten all about the drivers hahahahahahahaha
Yea inav 2.0 rewrote the whole mixer and this sort of thing works so much better
yea, but you still cant resource to pins, the resource listing nothing changes assignment when redoing motors and servos in the GUI, nor can u assign them to where u want to solder em??? Still have to play the guessing game, am I not correct?
BTW, u for those trying to figure out why the latest firmware won't do motor/servo setup check out the unstable releases.
👍👍
This is why bardwell rocks!!!.....because he actually helps people !!!!
strangeskull ha, helping by ridicule and making fun of a poor honest mistake buying the wrong motors once. I went to him for advise on what I could do with them instead of my original plan and he basically just laughed. Josh may be helpful on video but his personality is that of I'm better and smarter than you so I'm amused kind of person.
Sorry Josh but your $h*t stinks like the rest of us. Go ahead and laugh at more ppl who are absolutely new to this hobby and turn to the one person they think can really help.
There really just a motor that can tell its rotational position. Really cool you got that to work.
Do you offer personal help any more?
Yes of course. Feel free to email me is the best way.
this is nice but with inav 2.0 which is in RC phase now this will be greatly improved and simplified including info about assigned output
joshua?inav??? ahahahah nice!!!
I soldered off my M1 pad on my brand new Betaflight F4 board. Tried for months to get servos to work and move motor to other pads. This shit is so ridiculous donteven try it people. I have a delta wing setup with no working servos. Its a fuckin joke to move around and setup and VERY complicated microchip wise(PWM and Timers and I do this shit as a hobby AVR in C and still can't getit to work.
I´m so fuckin irritated at 0:31 after you left fullscreen of the window and "my" wallpaper appears -.-"
Sound like the church lady lol mmmmmmmm k?
INAV needs alot of work