Yiyibyus Diesel motor. Injector pump shims Delete! Maxing out the RPMS
ฝัง
- เผยแพร่เมื่อ 11 ต.ค. 2024
- Do I Kill this China Diesel with my Tomfoolery? watch me get this engine to max out in my driveway. "Driveway Revs"
1.We take the injector pump out and remove all the shims for driveway fun!
2.We bypass the throttle spring and what I think bypasses the Governor!
What does removing the shims do? I suspect it brings the pump closer to the cam lobe and in turns more fuel. 2. I think it might change the timing just a click or two.. again I’m an amateur trying to finger things out
First commercial ever at ColdStart Garage!
www.auxito.com...
Code for 15% discount is coldstart
Diesel Engine, 196CC 4 Stroke Single Cylinder Air Cooling Diesel Engine Recoil Start System for Small Tiller Walking Tractor Transport Vehicle Irrigation & Drainage Machine
amzn.to/3tVZU4z
Go check out my Instagram the link is somewhere on the About channel tab!
Email me at coldstart83@gmail.com
Thanks for watching ColdStart Garage Degens and Derelicts!
@BuildBreakFix
I have the same engine and I put it on my reel mower a year ago. So far, it works ok. Two things I don't like about it: 1. It's too loud (I need hearing protection) 2. It vibrates terribly.
Food stamp light bulbs had me chuckling.
🤣
Great and informative content here. Can't wait to see the new rotational bonuses propel you guys.
The Open exhaust, no shim driveway revs that occurred @13:58 revved really cleanly. No breaking up in the ketchup zone. This is notable.
Hmm. I was so focused on the twigs blowing around I completely missed that. I went back and watched it really quick 🤣
Bbf sent me here. love the channel
Thanks! Glad you found the channel. 🤘🏻🏁
I actually bypassed the governor on my little minibike gasser and just put a zip tie through and around the spring and it works great
We don’t need no government involvement with our small engines
@@ColdStartGarage yeah but I gets sketchy full throttle and sounds dangerous but really lived it up
Tell me about it. My knee right by the case bouncing off cutout. If it did let lose I may need a prosthetic after that 🤣
@@ColdStartGarage so far mine hasn’t so yeah nothing happened to me other then I got slapped on my leg with the chain but just gave me a scratch and but a hole in my pants
They grow up so fast! It brings tear to my eye he started it the right way this time LOL 🍺🤣👍 I had to say something couldn't handle suffering anymore as poor guy started it! I do enjoy a good youtube suffering on video! honestly though one point we all make that error when first screw with small diesel. Had one once about huffed and puffed trying to start it for hour..... then older guys laughing like watch this...... SOB! started right up without a broken wrist!
Ouch. I have one. Sichuan Sifa MB168F. I bought a 3/4 to one inch shaft adapter and honed the inside to .787 = 20 MM. With a 1 inch keyed shaft, I bought a 7 inch thin Vee belt pulley for an alternator. Your shims only change the throttle position. A governor is your friend because it makes your speed stable. Cold starts? Hot water on the cylinder. Mount it? On thick plate aluminum and not any kind of thin wall steel. I use 15W 40 oil and pump diesel. 196 CC's means it's a very small diesel good for 1 to 1 n 1/2 horsepower. I avoid the lowest idle and unnecessary high revs. Oil consumption is much higher than other motors so check quite often. If you don't respect it, it won't give you 2000 plus hours. It takes about 100 to break in.
Thanks for your insight. The little motor is shoved in the deepest corner of my shop. Cool little guy. But it was just a basic introduction to diesels for me. I had it on a gokart for a bit
@@ColdStartGarage You got it. These are probably the most precious engines we own. The castings are over the top. The dimensions are very tight. The alloys are meticulous.
@stanleybest8833 after theses first few videos. I stoped thrashing it. It’s in a safe spot. Forgive my ignorance in my videos. 🏁🏁🏁🤘🏻
Air planes are neat... I've always wanted a master rod to hang on my wall
Ya I wish I was into filmin’ sh!t back then. I’d have so much crazy stuff
He actually did it 😂 and you sound like a mixture of zip ties and bies and plies and vice grip garage 😂
Oh jeez. 🤣 that’s a combo right there
@@ColdStartGarage yeah maybe to make it roll more coal do some injection timing did that on my minibike and got a little more top end out of it but if u go to far then the low end has no power and I tried retarded timing and got a whole lot of low end torque but no top end power so I stuck with a hair of advanced timing and ended up blowing the chain off and you need to start uploading more cause I like your videos
Thanks for the inspiration. I do need to upload more. Last year got away from me. I can’t do once a week. Winter and all. But I have other ideas!
@@ColdStartGarage ya and it even doesn’t have to be about the engine just about anything
This is sport diesel !!! 😂🎉❤
I dont know if hobo freight is the same as princess auto .. but if it is you can buy cart and mini bike carcasses
Really? That be awesome
@@ColdStartGarage yes sir
@@chrismayberry4315 might have to check out princess auto website and see if they like bald eagle freedom units and ship me a dang ole frame!
They are pricy at the princess auto. 200 more at tractor supply it could come with an engine. Mini bike that is. So facepage market place might be the best option.
@@ColdStartGarage they where on sale not long ago that might of been when I seen them and yeah mark place is a deadly joint lol makes you buy a quad you didn't really need just for a challenge lol
No broken wrists? I want my money back!!
Next video we can break your wrists