(1859) Overlifting a Pin Tumbler Lock

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น • 141

  • @saschaschneider6355
    @saschaschneider6355 3 ปีที่แล้ว +30

    I really like that your videos aren't as streamlined as those of a lot of other pickers. Makes them much more relatable and I learn new tricks every now and then because things go wrong and you need to use your bag of tricks. Very much appreciated! And really great work on this. Congrats on not having to put this difficult lock into the naughty bucket

    • @noahway13
      @noahway13 3 ปีที่แล้ว

      @diprot I don't even watch LPL anymore. Every video is scrapped until it goes perfectly, and it seems like a little magic trick and a trite little phrase that the minions can repeat in comment section. "OMG, He said it was easier to get out the package!" or locks are labeled as junk and inexcusable because someone with special knowledge and a special tool can open it.

    • @saschaschneider6355
      @saschaschneider6355 3 ปีที่แล้ว

      @diprot although he's not the only one I was talking about, I've actually unsubscribed this channel since most of his videos have become ads for his company lately and the insane number of regular ads already annoys me to no end

    • @noahway13
      @noahway13 3 ปีที่แล้ว

      @@saschaschneider6355 Dude. AdBlocker. Easy fix. Serious. I forget that YT has commercials cause I don't see them (unless you watch on phone, and then it don't work for some reason )

  • @Weregus1
    @Weregus1 3 ปีที่แล้ว +11

    The hole is for inserting a colored piece/filling to distinguish between keys if you have more than one of them. Or at least it's used that way.

    • @janpolacek9782
      @janpolacek9782 3 ปีที่แล้ว

      Taky jsem to chtěl napsat. :D

  • @Large_Sarge
    @Large_Sarge 3 ปีที่แล้ว +15

    Man, nice job. That one seemed really tough. I thought it had you for a minute there. Thanks for sharing your knowledge.

  • @The_Hanter
    @The_Hanter 3 ปีที่แล้ว +2

    Not all of them have bitting like that. When I buying these FABs, some of them have pretty flat bitting and it's quite easy to rake it open. It's bumping resistant because of driver pin with bigger diameter on the middle of that pin (in FAB it's called "RBC pin") so the keypin is "drowned" under level of other pins and not making contact with bumpkey. On this position when RBC pin is can be maximum 3 cut. Those holes in keys are for plastic different colored identificators. Here in Slovakia and Czech republic are FABs the most basic and used locks and this company was founded in 1911 in "Rychnov Nad Kněžnou" in Czech republic (at that time "Czechoslovakia") and there are still there making locks until today. I was there several times on "open door day" that they got every day. I'm also collector of FAB lock and have interesting pieces, the oldest one is from 1938.

  •  3 ปีที่แล้ว +2

    Here in the Czech republic (FAB is originally a Czechoslovakia company) the FAB locks are standard. People generally use the word "fabka" for every pin tumbler lock. The hole in the key is for color identification - originally locks are sold with a few color "beads" then you can mark the key. I interesting in lockpicking and I already pick many of these locks. At now I have picked FAB with a similar profile on the table :-) I use valyrian hook (0.019") - it's about a "rotating" hook too. Usually i combine valyrian (0,019") and multipick hooks (0.015"). I have two FAB locks that I don't pick already (i have a key, but it's some older version of FAB - paracentric profile and both are quite hard operable with key -cylinder get stuck and on little wiggle, they turn- ...it looks like very worn out pins).

  • @boban250
    @boban250 3 ปีที่แล้ว +20

    Here in the Czech Republic FAB is basically the default when it comes to door locks, lockpicking you see in Hollywood movies seems so surreal here. You almost never see lockpicks here, locksmiths use bumpkeys or auto pick guns. Or if you've lost your key you will probably want to replace the lock and end up drilling it out :D

    • @arrrg3846
      @arrrg3846 3 ปีที่แล้ว +1

      I too see FABs everywhere and used FABs are available for a couple of bucks (be patient on Aukro.cz and Sbazar.cz)! ... however, I have yet to pick one (still a noob though). :( What does it mean when you push a binding pin half way up and then it's loose? ... and then 3 other pins are binding? .. and then you push on them and there's never any click? I'm looking at the working key while I'm trying to pick it and I still can't do it. :( In my head, I imagine a key/driver pin combination where the binding is always dynamic and every "set" pin will need to be dropped to "set" another pin. Really, the only clicks I hear in my FABs are the previously "set" pins dropping. I'm caught in an infinite loop and hoping a new algorithm will help me escape it. :)

    • @martinzember8721
      @martinzember8721 3 ปีที่แล้ว +1

      @@arrrg3846 Beware that many old FABs are nasty because they have beveled pins. They are more difficult to pick than the modern one on this video.

  • @czeDarkLight
    @czeDarkLight 3 ปีที่แล้ว +18

    Apart of color plugs fitting into the hole to distinguish keys, it actually serves as a break point. Even with fully inserted key, a piece of the key will still be sticking out, making it easy to take out that broken key with pliers or even fingers.

    • @clemdelaclem
      @clemdelaclem 3 ปีที่แล้ว +1

      why would you design your key to break easily but cleanly instead of just designing it to not break?

    • @czeDarkLight
      @czeDarkLight 3 ปีที่แล้ว +2

      @@clemdelaclem It's about where that break will occur. In this case, you won't need key extractor when it happens. Anyway, these keys are sturdy enough, they don't snap easily.

    • @derfuchs3296
      @derfuchs3296 3 ปีที่แล้ว +2

      Yeah that seems pretty smart. The key breaking is inevitable so you can at least design it in such a way that it can be easily extracted. Just hope the hole doesn’t actually reduce its durability below the average key because that would be even more annoying.

    • @joshuajhoyt
      @joshuajhoyt 3 ปีที่แล้ว +3

      @@clemdelaclem key strength is limited in the materials available for the key. Too hard of a material machining costs are too high and pushes the product price point so high it limits its potential customer base. Two bulky of a key and it is not practical to be carried with your other keys daily and in that sense it's not practical as a key needs to be. This provides a breaking point in a worst-case scenario situation but provides ample space for the key to be fully inserted operable grippable removable mostly still usable as a key after the break. This means that you do not need to have a professional with special tools come out and possibly remove pieces of a broken key from your keyway. You also won't be locked out of your house if that was the only key for entry that was available to you etc

    • @megatesla
      @megatesla 3 ปีที่แล้ว +2

      In the FAB 200, 1000 and 2000 documentation ASSA makes no mention that the colour dot hole also serves as a breaking point. Knowing ASSA I'm sure that if they had that in mind they would have designed the area better (even possibly scoring a line there) and would have mentioned it in the documentation for these keys.

  • @Optimus_Prime.
    @Optimus_Prime. 3 ปีที่แล้ว +1

    BRAVO BB!
    It's why you are one of the best!

  • @robertjung8929
    @robertjung8929 3 ปีที่แล้ว +5

    the hole on the key is for a plastic marker to distinguish between keys... the FAB2000 has 2 set of keys and a red marked key which will remove a small ball bearing from the lock and switch the lock to the second set of keys. the one in the video seems to be the FAB1000 version (the 2000 is silver in color not brass) but the key blanks are the same hence the hole.

  • @MarkHouston72
    @MarkHouston72 3 ปีที่แล้ว

    Happy retirement Bill. This video, more than any other has helped me most in my new hobby

  • @dazevers
    @dazevers 3 ปีที่แล้ว +1

    Truly outstanding Bill , you are right about the bitting on those FAB locks they’re all very Extreme. This overlifting technique is definitely the way to defeat these one’s. Have a great weekend.

  • @bradw0535
    @bradw0535 3 ปีที่แล้ว +9

    Excellent picking and demo on overlifting Bill! Wonder if the holes in the key could be for key identification. Maybe some color coded rubber plugs can be inserted? Thanks as always 👍🏻

  • @shadroid
    @shadroid 4 หลายเดือนก่อน

    That was amazing!
    I'm just starting on paracentric keyways and this was just what I needed to see!
    Thank you!!!

  • @bumpedhishead636
    @bumpedhishead636 3 ปีที่แล้ว +1

    That was a remarkable demonstration of your deep knowledge and skill!!

  • @diggerlenny4836
    @diggerlenny4836 3 ปีที่แล้ว

    Great picking!! Something tells me the locks that have made it to you're 'naughty bucket' have earned they're position there

  • @seatedliberty
    @seatedliberty 3 ปีที่แล้ว +1

    This video might not have been inspirational but it certainly was uplifting.

  • @derekbowbrick6233
    @derekbowbrick6233 3 ปีที่แล้ว +3

    "Yes baby". The sounds of completion.

  • @rykkyd1302
    @rykkyd1302 3 ปีที่แล้ว +1

    Wow, This looks like a great beginner Lock to learn on!

  • @et9775
    @et9775 3 ปีที่แล้ว

    Bill, I love watching your videos. Your skills as a lock-sportsman are unparalleled, and your explanation about everything is amazing, very detailed and understandable. However, if we are being real, I come for the lock picking content....I stay for dad jokes/banter!!! All the best from Texas!

  • @lockangel2256
    @lockangel2256 3 ปีที่แล้ว +1

    I mostly pick euro cylinder and often have to combine picks and techniques. Thanks for the masterclass.

  • @tomhejda6450
    @tomhejda6450 3 ปีที่แล้ว +2

    With a stock lock, you'll get colour-coded insets in the keys in the holes to distinguish your set of keys (that has the extra key for your office door) from your kid's (that has the extra key for their locker). I had many of these keys in hands, and trust me, they are not the ones suspectible to bending and breaking.

  • @twestgard2
    @twestgard2 3 ปีที่แล้ว

    My 2¢ is that you should publish the ones you don’t succeed in picking. I learn at least as much from seeing what doesn’t work, maybe more.
    Not to mention that having a few failures in the mix adds to the narrative suspense!

  • @miinyoo
    @miinyoo 2 ปีที่แล้ว

    Looked like a really rough ride. Nicely done.

  • @watauguy
    @watauguy 3 ปีที่แล้ว +24

    I'm not even signing up for the give-away this weekend. That lock is way (and I mean waaaay) beyond my skill level.

    • @penfold7800
      @penfold7800 3 ปีที่แล้ว +2

      Me too, but it is pretty

    • @c0mbo
      @c0mbo 3 ปีที่แล้ว +4

      So you can insert this into your door 😉

  • @ccadama
    @ccadama 3 ปีที่แล้ว

    @Bosnianbill. Thanks and great job Bill!. I was a bit worried when you said you were picking this lock before having breakfast. I was worried that you'd be hangry and break some picks because of it. Proved me wrong and you got a open for the win. And I had a good lock picking lesson today. Thanks again.
    Hope you and your family stay safe and well.

  • @parapicktog7734
    @parapicktog7734 3 ปีที่แล้ว

    I could see some of the picks you used were already bent before you even started.
    I haven't actually broke any picks yet, but a few of my favorites I had to replace after they got bent and mangled. You can bend them back into shape again, but they become softened and rebend again quite easy.

  • @penfold7800
    @penfold7800 3 ปีที่แล้ว

    Ive used that technique before, when I managed to set 3 of the 5 pins in a 60mm tricircle padlock by overlifting them all and then slowly with a bouncing movement allow one pin at a time to drop back into the keyway, whilst still being able to catch the driver pins above the sheerline. Then I was just left with two pins to pick. It's always worth trying out a couple of what I call 'luck techniques' if something is taking too long. Nowadays I get a lot of luck from the sparrows bogata. If you use a short hook inserted upside down to lift all the pins up, sometimes just rocking it on the way out works too.

  • @pyratemage
    @pyratemage 3 ปีที่แล้ว

    Yessss!!! Perfection in motion! Or words to that effect. 👍🏻 Just finished a 14-hour work day supporting end-user's that don't read emails from the IT department. I needed a resounding success, albeit vicariously. Thanks, Bill! You're the best.

    • @bosnianbill
      @bosnianbill  3 ปีที่แล้ว

      Man, I don't know HOW you do work like that! I envy your patience and ability to constrain your temper. If I had to work customer service (again), I would have to take up heavy drinking - and even THAT wouldn't be enough to keep my sanity...😀

  • @pattrass7692
    @pattrass7692 3 ปีที่แล้ว

    Come back to us bill. we miss you!

  • @Chuycabra
    @Chuycabra 3 ปีที่แล้ว

    It's not often I feel tense watching your videos, but wow!

  • @Baughbe
    @Baughbe 3 ปีที่แล้ว

    One thing though, when talking about extreme bidding, that means the outer pins will always be one of two cuts and and the back pins will have a limited choice of cuts as well to oppose the front cuts to get the pick pin block going... which means you have a much reduced number of potential key cut combinations. Still sizable, but you start getting to where random attempts of using a key from another lock might be the same as the one you try it on. Not common but not too rare either. I have opened a friends door with a old key from some random ones I found rummaging through old boxes at home and in thrift stores.

    • @RWBHere
      @RWBHere 3 ปีที่แล้ว

      *bitting 🙂

  • @RWBHere
    @RWBHere 3 ปีที่แล้ว

    Nice challenge. Well picked, Bill! Thanks for the demonstration. It would be even more relevant and interesting to see you tackle that lock the right way up, as if it were fitted into a door, instead of picking it upside down. 🙂👍

  • @Dr.Phillip
    @Dr.Phillip 3 ปีที่แล้ว

    The hole is for color coding. You can but in different colored rubber "ball" like pieces inside. So each family member can have a different color key for easy identification.

  • @visualist6x6
    @visualist6x6 3 ปีที่แล้ว

    Wow! Great job, Bill. Thanks for all you do!

  • @frankbiz
    @frankbiz 3 ปีที่แล้ว

    Great job Bill, that was one tough keyway and bitting. 👍🏻

  • @peterlhukas8030
    @peterlhukas8030 3 ปีที่แล้ว

    I have very similar FAB lock from my door and I as novice was thinking about lock-picking it, after I saw this video I am putting in back to drawer :-D. BTW that hole in key is for plastic color fill for distinguishing which key is from which door...

  • @formhubfar
    @formhubfar 3 ปีที่แล้ว

    Now that was impressive Bill, please send it to the LPL as a NA NA NANANA RITE BACK ATCHA BOI!

  • @napalmholocaust9093
    @napalmholocaust9093 3 ปีที่แล้ว

    A ten minute vid from you is quite a recommendation. Cheers.

  • @thelockpickinglebowski633
    @thelockpickinglebowski633 3 ปีที่แล้ว +1

    Phenomenal work!

  • @tkreitler
    @tkreitler 3 ปีที่แล้ว

    That was a tough one. Good work!

  • @11orkoslockpicks63
    @11orkoslockpicks63 3 ปีที่แล้ว +8

    FAB is incredible brand, locksmiths in Slovakia haven't easy job.

    • @ses5208
      @ses5208 3 ปีที่แล้ว +1

      Can't see any anti-drill inserts, so maybe their job is easy?

    • @11orkoslockpicks63
      @11orkoslockpicks63 3 ปีที่แล้ว +1

      @@ses5208 There are a lot of steel pins in fabs ; )

    • @ses5208
      @ses5208 3 ปีที่แล้ว +1

      @@11orkoslockpicks63Thanks for info, will have a closer look at FAB

  • @mscottdowning9682
    @mscottdowning9682 3 ปีที่แล้ว +1

    If you had broken the 10,000 pick within the lock, how would you have gotten the broken piece out -- especially if it had been the tip?

  • @freetipuk
    @freetipuk 3 ปีที่แล้ว

    Looks exactly the same as a Yale I have in my hand right now !!!!

  • @randommadness1021
    @randommadness1021 3 ปีที่แล้ว

    Going to remember this for when I next have a go at the only pin tumblrr I have left in the house that I haven't picked even once yet. Cheers man👍

  • @BD90..
    @BD90.. 3 ปีที่แล้ว +1

    Nice open Bill. That is more of hybrid picking though as Over lifting by itself. It is. Very tough to overlift a lock by itself.

  • @randywalton9866
    @randywalton9866 ปีที่แล้ว

    Miss you Bill

  • @gedd6750
    @gedd6750 3 ปีที่แล้ว

    Great video 👍, I have a euro lock that has stubbornly refused to be picked.
    Now I more knowledge to pick it.
    Thanks Bill.

  • @plug4uk696
    @plug4uk696 3 ปีที่แล้ว

    That did look like a tough one to pick, nicely done ;-)

  • @smlocks4907
    @smlocks4907 3 ปีที่แล้ว

    Great video as always bill very nice looking lock and a fun pick.
    Thanks for sharing

  • @motizer
    @motizer 3 ปีที่แล้ว

    Brilliant. Very well done.

  • @novo1178
    @novo1178 3 ปีที่แล้ว

    I wouldn't mind trying. Great video. Thanks bill.

  • @TheTranq
    @TheTranq 3 ปีที่แล้ว

    Lots of interesting techniques. Looked like a difficult one

  • @fordsfords
    @fordsfords 2 ปีที่แล้ว

    I know this is a year old, but I found this vid to be genuinely suspenseful, so I had to say something. BB: I know you won't see this, but man, I miss ya. Take care, and all the best.

  • @firepicker5174
    @firepicker5174 3 ปีที่แล้ว +1

    Gorgeous FAB!, awesome picking!

  • @grahams5871
    @grahams5871 3 ปีที่แล้ว

    what if you made a pick for those locks that have a bend that lets them conform to the shape of the keyway?

  • @gerbenvanegmond4007
    @gerbenvanegmond4007 3 ปีที่แล้ว

    Nice last resort trick!

  • @martinzember8721
    @martinzember8721 3 ปีที่แล้ว

    It's not so hard to SPP most of these but there is this trick: You start by setting the RBC pin first. (See The Hanter's explanation in the comments on RBC pins.) When it is mounted like in Europe, it's the keypin that is lower than others. This is what @BosnianBill did with the hook upside-down. Only then can you continue. Luckily, there are only 4 pins left!

    • @martinzember8721
      @martinzember8721 3 ปีที่แล้ว

      I also prefer to pick it similarly as in the video: With a city-rake in 0.015", setting the RBC and possibly a few others, then releasing the tension while rocking at the same time (it releases the over-set pins) and if the false set then seems solid, setting the remaining spool pins. Voi-la!

    • @martinzember8721
      @martinzember8721 3 ปีที่แล้ว

      Note that it works on these newer FAB 200RS that mention "FAB Assa Abloy", not the old ones that mention only "FAB". Those are completely different.

  • @dcw664
    @dcw664 3 ปีที่แล้ว

    Really enjoyed this one.

  • @DonzLockz
    @DonzLockz 3 ปีที่แล้ว +2

    Great skill Bill. Fab makes the US keyways look like a joke!

  • @martinharper5112
    @martinharper5112 3 ปีที่แล้ว

    Thank you Bill. What is the little cut out for on the base ofvthe key?

    • @martinzember8721
      @martinzember8721 3 ปีที่แล้ว

      It works as a stop for the key. It does not have a shoulder in the front but there is a notch at the back.

  • @ohmbug10
    @ohmbug10 3 ปีที่แล้ว

    Nice techniques Bill.

  • @seriousmaran9414
    @seriousmaran9414 3 ปีที่แล้ว

    Why the hole? Weaken the key to prevent a twisting attack with a spare key?

  • @roysammons2445
    @roysammons2445 3 ปีที่แล้ว +2

    Used all your knowledge on this one Bill. How come when I try that it doesn't work : /
    Great demo on overlifting a pin tumbler.

  • @jamesbridges7750
    @jamesbridges7750 3 ปีที่แล้ว

    Have Rare Elements make a set of his "Slurve" rake , it's a super shallow 4 hump worm . Great for getting in those really tight bends even though you don't get quite the "action" on the pins.

  • @MrJools70
    @MrJools70 3 ปีที่แล้ว

    Never tried that approach on a tumbler but I will now,Excellent stuff mate :)

  • @Jake-pc4fd
    @Jake-pc4fd 8 หลายเดือนก่อน

    The Legend, The Master!

  • @gkeyman565
    @gkeyman565 3 ปีที่แล้ว

    Take them anyway you can!!
    have a great day

  • @cyberhagen
    @cyberhagen ปีที่แล้ว

    That was an evil looking combination of keyway and bitting, yikes. The picking methodologies and strategy here were brilliant; I'm not remotely ready for this level of lock yet but this was very instructional! Figures I'd get into hobby this after BB has already just retired. At least he spawned dozens (if not hundreds) of other channels to learn from.

  • @Alex_dlc
    @Alex_dlc 3 ปีที่แล้ว

    what do you do if you break the tip of the pick and it gets stuck inside?

  • @johndododoe1411
    @johndododoe1411 3 ปีที่แล้ว

    Lowest possible pin must pass through the warding, so that depth must have access to all pins using a sufficiently angled pick.

  • @wiseone6251
    @wiseone6251 3 ปีที่แล้ว

    damn great job glade you did not give up !!!!

  • @billcarson1966
    @billcarson1966 3 ปีที่แล้ว

    That was an excellent tutorial! Thank you.

  • @RabidWolf1966
    @RabidWolf1966 3 ปีที่แล้ว

    No gutting?

  • @lucast3006
    @lucast3006 3 ปีที่แล้ว

    This must have been filmed during the “snow” we had the other day which was actually just miniaturized hail in Arlington/Fairfax.

    • @BlaubartMT
      @BlaubartMT 3 ปีที่แล้ว

      Word of the day: Gropple. Look it up. :) (also spelled groppel or graupel)

  • @Blap552
    @Blap552 3 ปีที่แล้ว

    Where can i buy a lock-vise? Haven't seen anything like it at harbor freight /loews.thx

  • @Fight_For_Freedom
    @Fight_For_Freedom 3 ปีที่แล้ว +1

    Very nice work!

  • @icanfixit1553
    @icanfixit1553 3 ปีที่แล้ว

    We are the pin heads from back to the future

  • @derfuchs3296
    @derfuchs3296 3 ปีที่แล้ว

    Amazing lock. I mean you got it open eventually but I bet every thief in the world would give up trying to pick this as soon as they see that keyway.

  • @sillyseppy7095
    @sillyseppy7095 3 ปีที่แล้ว +1

    Just WOW !!!!!!!!

  • @JohnnyDee62
    @JohnnyDee62 3 ปีที่แล้ว

    Oh, man, I hope I get a shot at this lock! 👀👍😁🔥

  • @Westhelockpicker
    @Westhelockpicker 3 ปีที่แล้ว +1

    Sparrows 12 thousands are thin enough and anything thinner like your using would just break and or bend so easily I don't think I would get much use out of them lol

    • @bosnianbill
      @bosnianbill  3 ปีที่แล้ว

      Yeah, I agree. I had RareElements custom make those 0.010" picks long before Sparrows offered the 0.012" goodies.

    • @Westhelockpicker
      @Westhelockpicker 3 ปีที่แล้ว +1

      @@bosnianbill I had to make handles for them. Shrink wrap just wasn't enough because there just so thin. 10 thousands is probably close to giving you a paper cut bill lol

  • @tomhejda6450
    @tomhejda6450 3 ปีที่แล้ว +1

    I can assure you that not all FABs have crazy bidding like this. Some of them are pretty flat, but maybe this has gotten better recently. (I've had FABs around me for my whole life, so I'm getting lost in how they do recently.) The weakest point is they're quite easy to drill open, even with one of these spinner covers over your euros. But what would you want for less than 20$?
    Btw, too bad you didn't gut it, I was curious what driver pins it had in.

  • @TMHMooseMoss
    @TMHMooseMoss 3 ปีที่แล้ว

    i think that hole in the key IS to pre weaken it. better to break 2 keys and be able to get them out than to break 1 key and have it stuck in the lock forever

  • @donnierobertson3088
    @donnierobertson3088 3 ปีที่แล้ว

    Great job and video like always

  • @johnabrams8148
    @johnabrams8148 3 ปีที่แล้ว

    I love this video. Thanks!

  • @kewltune4683
    @kewltune4683 3 ปีที่แล้ว

    Wow! Well done! Would anyone know where i can purchase very think picks in 10,000th of an inch thick?

    • @justie1220
      @justie1220 3 ปีที่แล้ว

      Rare elements is the company that makes the .0001” picks that bill uses. Google them and they’re near the top

    • @kewltune4683
      @kewltune4683 3 ปีที่แล้ว +1

      @@justie1220 Rare Element website been down for a while. Any other suggestions? Thanks!

  • @DavidPirouet
    @DavidPirouet 3 ปีที่แล้ว

    That looks like one that would be interesting to do.

  • @nich882
    @nich882 3 ปีที่แล้ว

    Well done bill! 👏👏👏

  • @Alx-SG
    @Alx-SG 3 ปีที่แล้ว

    BRAVO SIR!!!!!

  • @keezin1
    @keezin1 3 ปีที่แล้ว

    epic battle

  • @sv040
    @sv040 3 ปีที่แล้ว

    Where can I write to you? I have a business proposal for you)

  • @brianfackrell4139
    @brianfackrell4139 3 ปีที่แล้ว

    That's how I feel with any lock. I'm just starting so i won't try to win this one, give someone better than me to get it.

  • @gozzendk
    @gozzendk 3 ปีที่แล้ว

    Thanks for the video 🔑🔒👍

  • @stevef.m.2188
    @stevef.m.2188 3 ปีที่แล้ว

    Thanks Nice

  • @billhenderson731
    @billhenderson731 3 ปีที่แล้ว

    Excellent pick. Well talked through. I’ll have to try that overlift technique.

  • @RoeLunatic4ever
    @RoeLunatic4ever 3 ปีที่แล้ว

    Jikes....this is definitely an 'expert' pick!
    Realy nice!!!!

  • @TheCommuted
    @TheCommuted 3 ปีที่แล้ว

    "The fact that you are seeing this video tells me that this is going to work." --What does this day about the nature of the universe?

    • @xXDeltaXxwhotookit
      @xXDeltaXxwhotookit 3 ปีที่แล้ว +2

      Maybe our universe is in a massive naughty bucket... it would explain a lot :-p

    • @RWBHere
      @RWBHere 3 ปีที่แล้ว

      @@xXDeltaXxwhotookit 😁👍

  • @xntumrfo9ivrnwf
    @xntumrfo9ivrnwf 3 ปีที่แล้ว

    If you had to guess, what % of locks that you attack currently do we "not see because they go in your naughty bucket"?
    Edit: congrats!!! can't imagine opening this one....

  • @nord_laender
    @nord_laender 3 ปีที่แล้ว

    great!!

  • @jbombrobertson4765
    @jbombrobertson4765 3 ปีที่แล้ว

    I gotta try that over lifting method more often!