Maximum Acceleration Test (How Fast Can You Go?)- Sonic Pad Intermediate Part 8
ฝัง
- เผยแพร่เมื่อ 6 ก.ย. 2024
- In this video I'll show you how to test what your klipper controlled 3d printer can do and show you how to set a limit for your acceleration to avoid print defects at higher speeds.
*Since recent firmware change, it is necessary to issue a 'restart' command after changing any settings or following any calibration procedures.*
Ringing Tower stl: www.klipper3d....
Commands to copy & paste
Zero Pressure advance:
SET_PRESSURE_ADVANCE ADVANCE=0
Acceleration Test (1500mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=1500 STEP_DELTA=500 STEP_HEIGHT=5
Acceleration Test (7500mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=7500 STEP_DELTA=500 STEP_HEIGHT=5
Acceleration Test (6000mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=6000 STEP_DELTA=500 STEP_HEIGHT=5
Affiliate links (If you purchase something after clicking any of the below links I may earn a small commission at no cost to you. This is a great way to support the channel)
*Creality Sonic Pad*
UK: www.geekbuying...
US: www.geekbuying...
Everywhere else: www.geekbuying...
Discount Code: NNNCRESONPAD
Amazon
amzn.to/3AiYtwD
Discount code: 10NTDPJE
*Other Sonic Pad Videos*
Sonic Pad Review: • Creality Sonic Pad - T...
Sonic Pad Basic Series
Part 1 - Connecting to a Creality 3D Printer: • How To Connect A Creal...
Part 1a - Connecting to a non-Creality 3D Printer: • How To Connect A Non-C...
Part 2 - Completing initial setup: • Completing The Initial...
Part 3 - Starting a print and UI Tour: • Starting A Print With ...
Part 4 - Controlling remotely and WEB UI: • How To Control Your So...
Part 5 - Connecting a camera and tinelapse videos: • How To Connect A Came...
Sonic Pad Intermediate Series
Part 1 - PID Tune • How To PID Tune With T...
Part 2 - E-Steps/Rotational Distance • How To Tune E-Steps/Ro...
Part 3 - Slicer Settings • Slicer Settings and Pr...
Part 4 - Sending Prints From Slicer/Images On Screen • How to Send Files To Y...
Part 5 - Input Shaping - • Tune Input Shaping Wit...
Part 6 - Pressure Advance - • Video
Part 7 - MACROs - • Video
Part 8 - Max Acceleration - • Maximum Acceleration T...
Part 9 - Mid-print Filament Change - • How To Complete a Mid-...
Other
Firmware Update September '23 - • Creality Sonic Pad Fir...
Creality Sonic Pad - How To Update Firmware Without Losing Everything! - • Creality Sonic Pad - H...
..............................................................................................................................................................
BUY ME A COFFEE
If you're enjoying my content, why not consider supporting the channel by buying me a coffee?
Even very small amounts are greatly appreciated and re-invested into bringing you better content.
www.buymeacoff...
You can also use the TH-cam 'Thanks' button above if you prefer.
...............................................................................................................................................................
If creality was wise they’d pay good money to buy these videos and release them for sonic pad themselves. These are so helpful and so well done!
Or better yet, Hire Ricky to handle their English Speaking division of Technical Support....
@Ricky Impey - Please look into your commands you have listed
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=1500 STEP_DELTA=500 STEP_HEIGHT=5 does not work in the newest version of the Sonic Pad Firmware
This command appears to work:
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=1250 FACTOR=100 BAND=5
EDIT:
Also, if you have done the input shaping/resonance shaping, please make sure to perform this step too:
SET_INPUT_SHAPER SHAPER_FREQ_X=0 SHAPER_FREQ_Y=0
This will disable the current resonance settings in the printer config
I hope this helps anyone that comes across this post
How to you set turn it all back on?
Ricky, I have been an instructor for 34 years and let me tell say that your way of explaining technical things is straigh, to the point and very clear. Whenever some other TH-camrs explain things, I can tell they love to hear themselves talk because they go in circles and use fancy languaje. THANK YOU for these fantastic informative videos. I have watched your videos before and just for that I did not even look at the manual of the Sonic Pad I just got, I went straight to your videos. Amazing videos, thanks again.
Thanks Tony, that's great to read👍
I almost returned my sonic pad because I kept getting stuck and it wasn't as plug and play as I had thought. I've followed each of your videos now and it's all running great!! Seriously, these vids are amazing.
Great to hear, thanks. Yes, I get so annoyed with manufacturers releasing these product without propper support .
Thanks a bunch for this series Ricky.
When I bought the Sonic Pad, I assumed it'd be plug and play, or at least the tuning would be covered in the User Manual.
Turned out neither was true. So many YTers keep giving rave reviews to the sonic pad, but ALL of them literally skip all of this setup process.
Thank you for literally doing Ender's job and making a proper video guide on how to setup and actually put to use the 150 I spent on the device
This is still the best video series explanation after almost a year with my pad haha
Are you using PrusaSlicer with SonicPad?
@@rubenverster250 I use Cura exclusively. But I have to learn some new ones with Anycubic 3 on way.
I was waiting for this, bring on more. I'm learning a lot.
Massive thankyou to you tutorials on the sonicpad. Followed them step by step on my cr10s pro v2 and is running perfectly. To be honest it was because of these videos I was confident enough to move to klipper. Now I want to build a voron.....
Lol you just described me
How did you do max acceleration?
OMG am I so glad I went through the whole series to get where I’m at, I haven’t printed very long, but I can see the quality of my prints changing from that first unboxing, and it’s all thanks to you and your instructions. Starting with the how to assemble your Ender 3 V2. Tyvm!!
Thank you for sharing your knowledge and experience. I’m in week 1 of owning the Sonic Pad with my Ender 3S 1 and enjoying the new possibilities. I just need to implement your advice to get the most out of both. Great job and looking forward to seeing more. Cheers!
My comment will probably get lost in tones of others, but I have to let you know Mr Impey that you have made an amazing set of videos that are straight to the point and wasting no time on useless chatter. I am just an online stranger, but you have my respect and if I ever meet you irl, I would love to buy you a beverage of your choice to express my gratitude!
I'm so happy you had all these videos already out, by the time I got my Sonic pad two weeks ago. I was able to halve my print times while still getting a bump in quality too.
Great to hear👍
Thank you Ricky. Your videos are a salvation to those entering the Klipper and SP world!
Are you planning any tutorial referring flow/maximum extrude speed?
Extrusion speed + acceleration combo would turn our “affordable” printers into Voron-ish printing machines ❤
Hi, it's on the list but i'll bump it up a little, thanks.
WOW i have found all these videos so helpful got my sonic pad up and running with each video finally someone that i can follow as your videos are well worth watching for any assistance just brilliant such a detail setup ☺☺.Great job, my setup was the ender 5 plus
Amazing video. Finally all the information needed in one video.
This was great but just make sure you restart or reset your printer after running the test. I had 11k acceleration set as the max and ended up layer skipping because my printer didn’t default back. Not a big deal just Klipper should probably reset by default when you end the test.
Thank you for taking the time to make this series on the Sonic Pad. Your video on setting up the Sonic Pad on a non-Creality printer, was the tipping point I needed to order my very own one, that I'm happy to announce, arrived today.
I will be rewatching all the tuning videos as I go about setting up my Biqu B1 to make use of Klipper, the "easier" way, all thanks to your tutorials.
best series of videos i have ever seen and helped a ton with my new rebuilt modded cr10s5 with klipper, BTT board and tft 35 screen, Bondtech,Silicone bed, a custom built bed with 6 adjusting knobs, and more running it with the pad. keep it up man !!
Your video series on the Sonic Pad was extremely helpful and very nicely made! Had my Ender S1 Plus up and running with the Sonic Pad in short order. Thank you!
Every time I try to print something without top or bottom layers, the printer cant even start the file properly... sometimes it starts the print at some random percentage or it wont even do a thing. I just tried to print this calibration tower, when the print ''started'' it skipped to 47% halfway done in the Gcode... It didn't even home the axis or anything and started printing in mid air haha. I added a top layer and now its printing. Amazing tutorials btw rick, you're the best !
Oh there is more dude I’ve been using my sonic set up to the vids you have so far and it’s a dream
Thank you for this series! You have made my printer come alive!
I ran this test twice running the tuning_tower_command.. set to start at 7500 and never noticed and difference in the prints.. ended up setting the max accel to 7500 and calling it good.
My question is should i up that more lol.. ender 3s1 creality high flow kit and zuff 5015 part cooling and hot end fans.
How does that run?
Here I am again. I have now bought the Sonicpad instead of the Bigtreetech Pad. I have set everything as you explain in your videos. Now I have better print results and print much faster.
Now I will rework the component cooling of my Ender 3 S1 Pro, because it is too weak for fast printing :D
Thank you for your helpful videos. I hope there are more to come :)
Wow, thanks very much! There will definitely be more to come in the Sonic Pad series. Also, I plan to test out some cooling options for the S1 Pro too as it is the main thing holding it back now.
@@RickyImpey I'm really looking forward to it :)
Hey Ricky, thank you for the videos. Any chance you'll be throwing together a PrusaSlicer tips/tutorial tuning for your Sonic Pad setup? I would be interested in seeing (as I'm sure many are) how the settings and tuning translates outside of Cura and into PrusaSlicer. I haven't found any definitive walk throughs specific to the walk throughs you've given us, what to plug in and where.
Thank you!
A lot of people have requested this so it is something I plan to do👍
@@RickyImpey thank you!
Usefull as usual. Your videos make the learning curve so smooth
Odd question here, are we to measure the X or Y side for determining the max speed? The gaps seem to widen on the X side, but on the Y side they are closed! Also, cheers another great video!
It's best to go with the worst one as accelerations are not separated between the X and Y axis with Klipper.
Great set of videos Ricky, they've been very helpful. Sonic Pad wise, maybe some insight on the during print "Adjust" button (blue coloured middle one), and why you might want to do that? If you get stuck for ideas, some general maintenance tips and advice on achieving correct belt tension on the S1 Pro would be appreciated. Thank you for all your great work.
Hi Ricky, have to say loving your Sonic Pad series. although still relatively new to 3D printing having watched your video review on the ender 3 s1 pro purchased one and then a while later the sonic pad. I find the videos very informative and easy to follow for a novice. many thanks for creating them and please continue to do so. Excellent videos.
Great video man!
Blooming fantastic series Ricky!!!
Thank you. Once again, a superb video. Cheers.
This series has been immensely helpful in getting my Sonic Pad setup on my E3 S1 Pro! Would you make a video on using the Sonic Pad for high speed prints with TPU?
I would love this too!
Hey Ricky , thanks for the tips setting up. I have a particular dislike for cura and it’s inability to work well with certain things - I’d like to use Bambu slicer but when used it things their is no extruder configuration - it works with cura fine but not with Bambu despite changing start/end gcode as per creality guide in the preset in Bambu - if I leave the stock gcode it does work but sort of half properly and I can’t really see a way to ignore slicer speeds in bambu like cura - the issue is I’ve rarely gotten any decent results when slicing with cura vs prusa or Bambu
Getting ready to run this test. I have watched all your Sonic Pad videos and they are outstanding. Only thing that would be nice, when making a bunch of changes in the slicer settings, would be very helpful if you listed them below. I rewatched that section over a dozen times to be sure I got them all. Thanks for all you great work. I am using Creality Print as they have Sonic Pad specific profiles for the V2 and S1 and some others. It gives a 37 minute benchy on the V2 with Sprite extruder.
Hi Ricky!
Thanks for your videos! They are awesome!
Can you please tell me why the acceleration settings are reset after the first pass of the extruder at the beginning of printing?
Printer Limits defaults to 2000, but after the first pass it resets to 500.
Ender-3 S1 Pro, Sonic Pad, Orca (Prusa, Cura).
Thank You.
I'm not sure what I'm doing wrong. I've followed all of these tutorials step-by-step and I was able to get my Ender 3 S1 Pro with the Sonic Pad to achieve these much faster speeds and better quality on the test prints that are linked in the descriptions of each of the videos. However, if I try to print anything else, they now all fail in spectacular fashion.
Awesome video once again Ricky! The main trouble I have had is setting up a second web camera to monitor a second printer. I wonder if this is possible? I know the Sonic Pad is capable of controlling 4 printers at once, but I am keen to use 2 printers with 2 web cams. Would be great to see a video on this, if it is indeed possible. Thanks again for this series, it has been super super helpful!
Unfortunatley, two cameras is only posible with root access. I haven't gone there yet as i'm not very knowledgeable with Linux yet.
Would love it if you did a guide to set the x and y probe offset.
Great video! Can you share where you got the spiral cable management for your hotend wires?
It's part of the Minimus hotend kit. Here is the video: th-cam.com/video/uZ2NJfgmYYU/w-d-xo.html
@@RickyImpey Thanks
Thanks a lot.
I'd like these videos for Orca Slicer. Or a a video : how to set up properly your Ender 3 S1 Pro + Sonic Pad in Orca Slicer.
Thanks!
Welcome!
Silly question! Love the series btw! How is acceleration determined for printing then? Does klipper just use what it feels is right with the input shaper limits or new limit you have just updated?
inputshaper just meaures resonance it doesnt set limits
Very good, amazing channel. for when a video to be able to use it from outside the home??
Your vid’s are the best, and I trust your knowledge.
Could you do a video explaining how the macros work, especially regarding time-lapse , get Time-lapse setup, hyper lapse, etc? Each time I press these macros, it messes with my camera and I’ve had to ultimately turn off time lapse for my camera.
Furthermore, could you do an explanation on how to make a 1 macro for pausing a print, changing out filament, doing a command of G1 F200 E50, and resume print (essentially a M600 without having to slice it in with slicer) - Since Creality did an update and messed with the M600 command. Then explain how to put this IN the print cfg? I ask, because each time I try - I am doing something wrong and my SP throws an error.
Thanks Charlene, I will make some notes and see what I can put together with regards to all of these suggestions.
Great vid! Is the stock s1 pro fan efficient enough for higher print speeds? Will you make video about 5015 fan upgrade?
I am currenty looking at cooling upgrades for a future video on this, yes👍
Thanks for your basic and intermediate sonic pad series, these were EXTREMELY helpful!!!
Having just completed the test in this video on my Ender 5 S1, I find that the gap behind the X wall is perfect all the way up to 13500 (I feel this axis would still be good at 20000), but the gap behind the Y wall starts to become wider at around 6500 - 7000. So I guess I should set my max acceleration based on the gap behind the Y wall, so around 6000???
I was having the same predicament. Well, the first couple days I've been trying to do this, it wasn't working because some of my settings were messed up and on some prints I forgot to disable pressure advance. Now I'm having the same thing happen as you, where there's not really much gap in my prints, and I'm afraid to test much faster because it starts to sound a little violent on turns. I think I will try a higher speed setting, say 125-150, and try one more time.
Now that you've had some time, have you learned anything since you posted this comment? We have the same system and I'm really curious what your experience has been.
@@bungle6334 I've not learned anything new...I've just left the setting at 6000 and I am happy with the quality fo my prints...
Great tutorials Ricky. Well done! Cleared a lot of things up as a new user of the Sonic Pad. Two videos in the intermediate list are missing though, parts 6 and 7. Are they no longer relevant? Thanks for the great work.
Great videos, really helpful.
Question... What about the print speed setting in the slicer or is that controlled with the velocity (500) that is the printer.cfg file?
Hi, the config file velocity is a maximum limit. The speed is still controlled by the slicer. Did you see my Sonic Pad Slicer Setup video? It may help answer some of your questions th-cam.com/video/Aqi5vjE0_QU/w-d-xo.htmlsi=QRNeKS5ib8pNgB99
Hi, Thanks. Yes I have seen them all, probably more than once...
Great video, as always.
I'll make sure to check it out now that you explained really simple how to do it.
Will you go into print-speeds aswell? Currently I am running 120mm/s for print speed and 80mm/s for outer walls. I think I could go higher but so far I haven't been able to find proper tests for this.
I am really happy with the speeds I have right now but I appreciate every step and tweak you show.
Keep up the great work!
I will give print speed some thought as it can vary massively depending on what you are printing. selecting the correct speed can be a bit of an art but there are some factors to take into account so I could explain how I decide on speeds to use. Thanks for the comment👍
Thanks for the video! Your concise and understandable videos have been my go to since I bought my S1 Pro, from tramming the bed to adding and tweaking the Sonic Pad. I do have a question and video suggestions, one of the recent Sonic Pad updates added support for the laser module, curious how that would work since the Falcon box is controlling the motors and supplying power to the laser? Also maybe you can make a filament change video using the Sonic Pad? Thanks again for all the help.
Thanks for your suggestions👍Creality have confused things by selling two separate laser modules that will work with the Ender 3 S1 Pro. They have a 1.6w and a 5w unit that can be controlled by the printer's control board but then also the complete separate add on 10w kit that I reviewed. The 10w kit is separate and, like you say, controlled by it's own control board. It's the lower powered units that the Sonic Pad can apparently control but I don't have one of those to try.
@@RickyImpey Oh I see , thank you
so I have completed your video series and configured my ender3 max Neo accordingly. However on this test my max acceleration is about 3,500. What's up with that? how can I tune my printer to get a better result?
Don't forget to disable "spiralize outer contour". Otherwise, your future prints will be funny. Happened to be me - lol
Wait, dumb question on the first run of these commands and print, my "Y" face has no gaps, but on the "X" Face has gaps about 4th line up. I have an Ender 3 S1 Pro and have done all of the videos in the basic and intermediate up until this point. It's only a month and 8 days since I've had it... I don't understand why yours is so much better than mine and can print at higher speeds etc. This is my first 3D printer and I've honestly had problems getting and keeping it level (hence the Sonic Pad) and am highly debating on switching to linear rails on all axis and a glass bed. I've had problems with a warped bed that I've had to persuade back into place which has helped immensely and I literally don't have to relevel every day, I've had to recheck all of my springs, add nuts to keep the bolts from spinning when leveling, recheck bearings and wheels, I've tried solid rubber spacers. It's marketed as a beginner friendly printer and I want to rip my hair out.😅 Thanks in advance NxP
i have followed along up to this point, however i have awful banding/ringing all the way up the print on input shapping i only managed to get 4 layers up before i could see through the print. i have layers missing from the start of the layers ect.
do you have any suggetions on what wrong?
Have you followed all of the previous videos in the series? PID tune and Rotational Distance especially?
If you have set both of these then make sure your slicer flow settings are at 100%. If the problem persists then have a look at your extruder and make sure you don't have any issues there that may cause an under extrusion.
@@RickyImpey I gave up Ricky I did follow all the videos in the series was really good.
I think the flow rate like you suggest could have beem wrong as I switched slicer to default prusa profile and used that and came alot better but still bit of ringing.
I have now ordered a bambu lab p1p hopefully I don't have to mess around to much 😊
Cheers for the reply content is solid keep going.
Have you rooted your Sonic pad? A few Klipper packages I’d like to add to the Sonic pad like Fluid, KAMP etc.
thank you
I went through all your videos and love them. My Sonic Pad is a machine and working great thanks to you. My only dissatisfaction with the S1 Pro is there is not alert tone when it moves for a filament change so text notifications would be very convenient. The descriptions on the forums are a little over my head and it doesnt seem to be done on YT. Your videos are so easy to follow would you consider creating a video on moonraker notifications through telegram or through other methods?
7K acceleration speed on your ender 3 s1 pro? crazy, i must be doing something wrong. Although i was doing this test with PETG, i could only get 4-4K accel speeds (chose the lower for quality.) could you or someone advise me on what i may be doing wrong? ive literally followed this entire guide a few times. Belts are tight and so are the wheels (no slop in the head) or is this because of using PETG rather than PLA?
These videos have been really helpful but I've struggled with the acceleration test. Unfortunately I can't see any changes which makes me think the codes I've entered are being ignored and not that my printer can go super fast!! It's an Ender 5 Plus with direct drive micro swiss NG Revo. Are you going to update them as there appear to be a lot of changes on the sonic pad with q codes popping up. Thank you again for great videos.
Another great video, do you have any suggestions on how to get a good bottom print of an irregular object ? I find unless you have a flat surface object the bottom layer is always rough, is there anyway to get around this ?
Anything that isn't flat on the bottom will very likely need supports. It is possible to tune support settings to improve the surface they leave after you remove them but a supported surface will never be as clean as a top surface unfortunately.
How do you figure out the accel to decel on this video I see it’s at 3500 I’m just trying to figure out how you come up with that bc in mine it’s at 7000
Hi ricky, First off happy christmas to you and your family, so i have followed all your videos up till this point and now i have one question, You have covered Max Acceleration but what about Max Printing speed or dose the klipper side of the sonic pad choose that? at the momment im at 150mm's printing speed
Hi there, First thanks you for all the video tutorial, it is very cool to learn that way.
i have a cr6 se and if i disable the pressure advance i have gap juste above 7500 acceleration. if i enable it i have gap directly on the beginning of the print. is this normal ?
That doesn't surprise me. Have you tuned pressure advance already?
Thank you for your video series for the sonic pad. Im just curious. So the slicer settings for the Pressure advance test was only for the test(right?)? How about the Max Acceleration Test, do we reuse our Pressure Advance value after the test or not?
only problem is i cant use cura, i got to the spiralise bit but bambu doesnt have that option only spiral vase mode
Just got an Ender 3 S1 for Christmas and added a sonic pad. Everything is working fine, except I'm confused on this test. On the X side a hole opens up around 2200, on the Y side, there are no holes until around 6000, and those are just pin holes. the x side has more like slits. I'm not sure I understand what to make of that. Also, if I'm maxed out at 2200, is there anything I can upgrade to increase that?
Same Problem, also looking 4 help pls !
@RickyImpey The main indicator of the best acceleration are the gaps? Despite the gaps, which in my case also started at around 7500, the printing itself looks very neat, the corners are also very good despite this speed. My question is, can we get even faster print speeds by setting higher acceleration values without compromising quality?
This may be a stupid question but do I need to change anything in Cura profile once I have done this?
How about a troubleshooting guide
Anyone getting an error after running the first test and then starting the second one at 6000? I got a "Move out of range:...." error trying to start the second print. Had to delete it from the Sonic Pad and re-upload it.
Check your slicer machine settings. This is most likely your slicer thinking your bed is bigger than it actually is.
Love your videos but im getting different gap on X and Y. I wish i could understand why. i did all the resonnance, e steps, pressure advance ( which i turned off for this test ) but i get gap on all X, but Y only starts at 3000 ish. Then i did another test from 500 with steps of 250, same thing, X is gapped, and Y starts at 2000 ish. I hope there was better speed on the cr-m4 lol
Hi, can you explain how to connect the web user interface of the Creality pad 2 to the Mac book
Wondering if Rick could help me with Sonic pad. I can't find the filament sensor settings so can't do multiple colours or fit new spool.
Thx. Great content!
Can you edit via console/printer.cfg file also the "maxtemp" setting if your printer has a hightemp hotend (in my case a creality spider Pro, v3) ?
Hey Rickey, I've followed you through the entire setup of an ender 3 and running sonic. You've helped me with so much. Have you ever run into the problem when using ss and uploading through web UI it stops with a webhook error? I've turned time-lapse as I don't use it but it's still stopping. Thanks for any insight you might have.
Hey Ricky great videos I've watched just about all these tuning videos!! Quick question...Do we have to re-tune pressure advance after setting it top 0 for this ringing tower test?
No Scott, it will reset to whatever you had before when you save or restart
@ricky, I am using orca slicer. Main question is about "enable acceleration control". Is there a similar setting on orcaslicer? What else would it be called. Any other tips on settings to use for this test in orcaslicer?
@RickyImpey,
Just a curiosity and for my clarity, when you're speaking of the 7500-15000 ranges you're referring to mm/s SQUARED, correct. You repeatedly said mm/s but if my printer runs at that speed it would fly the hotend off the gantry lol
hello there iv been enjoying your videos on sonic pad and have followed them. i have a couple of questions though. i am using the sonic pad with an elegoo neptune 3 pro and using Orca slicer. ive been trying to tune acceleration but it seems to print at the same speed with some under extrusion. i was wondering if i have to 0 out the parameter that says normal printing on the acceleration setting in the slicer?
Hi, creality sonic pad does not work on sonic pad when I plug in creality webcam. How do I get this to work?
What do i write in the console when i am done testing this, to make the printer go back to its normal mode, and not make the accelleration faster as i progress through the layers?
Set up AI detection next?
After going through all these Sonic Pad videos and cranking up the speed I am having problems with Bed Adhesian. Any suggestions?
I dont understand what you mean by the gap opening up? Ive printed but dont really get what im looking for
Do I need to turn pressure advance back on after the print is finished via a console command or does it do it on reboot?
It does it when you reboot
Hi Ricky, have you been keeping up with the Sonic Pad? There is a lot of on-line chat regarding issues with updates etc. I have only updated once and after struggling to connect to WiFi, I have no major complaints. However, I don’t want to carry out further updates if they are going to ‘brick’ my machine.
I've just printed this starting at 6000, quite a bit of ghosting but no gaps. Should I continue to the 7500 test?
Supports!
I am finding that supports do not print correct and end up in a mess.
Any advice on this and what settings should be used via Cura?
What should I do if I see the gap open starting at 1500?
Yessssss
Have you looked into adaptive meshing and do you see an advantage to adaptive mesh vs the standard bed mesh configuration?
Hi Rickey, followed all your videos I am using an ender 5plus all set up and printing great. Thankyou. I have one question I changed the max velocity in the config file. Printing superbly at 7000. But every time I slice a file and send it to the printer via console it reverts back to 500. I then have to change it on the console back to 7000 hit enter and it speeds up. Is there a way to set that speed for every print or should it hold. I am using cura 5.1 as the slicer, speed in slicer set at 100mm sec.
That's strange, changing it in the printer config file is the way to change it permanently. Make sure you save and restart the Sonic Pad after as it doesn't save until you do.
Hi Ricky sorted issue. Problem was start up code in cura as per advice from user in sonic pad community. Changed and working perfectly
I’m not sure what I’m doing wrong but everytime my print finishes the printer head don’t clear my print. I have noticed it in the ring tower
You probably need to check you end g-code. There should be a command line to raise the z axis so that it clears the print and moves away.
@@RickyImpeyThe z was at 10 in the end z code in the Cura thing. I switched it to 30 still the same thing. Only thing different it does is the print bed don’t continue to move but the print still hits the z axis. I don’t know if it’s the z axis or the print bed. I havnt had that issue with prusa. Also I have noticed that when I was fallowing your intermediate videos the sonic pad didn’t restart on all the videos yours did.
@@damageplan1978 copy and paste your end g-code into a reply below and I'll see what it's supposed to be doing.
Ricky, did you change to a high speed filament or is standard still ok to muse at quicker speeds?
Do we need to do something with the Accel to Decel value?
In your videos you ask us to disable "enable acceleration control" in our slicer. I usually check the slice to make sure the Volumetric Flow is within capable range of the printer. I would assume that disabling the feature as you mentioned would then render the slicer "flow" preview un-useful? Could you elaborate on this or anything to do with volumetric flow/Klipper/sonic pad. Thanks.
how do you restore pressure advance after the test?
do you use the same configurations for all itens you print or only in these you tested? thanks! you're awesome
The acceleration figure is just a maximum limit on what the machine can achieve. It will stop the machine from going over this limit no matter what you then set in your slicer, a bit like a rev limiter on an engine.
Can anyone please help me from having the z axis hit my part after the print??
hey! thanks a lot for your videos! on my ender 3 s1 plus, when the bed moves fast with an acceleration over 1500mm/s², it vibrates as hell. How can I solve this??