Простой одинарный узел, нормально держит! Сколько сданий построил,фундаментов и сейсмопоясов,досихпор стоят!Сейсмический район Центральной Азии,Алматы!
I've been to quite a few construction sites in Denmark over the years, and get what you mean. But with that being said, I think many if these tips is for those not in the industry, or those that doesn't have the advantage of picking up tricks from the oldtimers on the job. Hav en god weekend!
There’s less people in the whole of Denmark than London so you can choose to do any time wasting thing you like. (JK, it would be nice if we could outsource the government of Britain to Denmark lol)
@@МаксМакс-е1н Ошибаетесь уважаемый. Не вся арматура сваривается, как и не вся связывается. Зависит от конкретного проекта, нагрузок, бетона, марки самой арматуры.
@@naturihaus1744 арматуру категорически нельзя сваривать при заливке бетона. Почитай книги и узнай для чего нужна арматура в бетоне и какая её роль там
Ya know, they actually make the wire with loops on each end. And the hooked installation wire twist tool! If we could attach pictures, I would send a picture of the actual installation tool!
Idk what you were doing but as an ironworker I can tell ya I’d be asking to see that tool and chucking it off the building. Klein pliers and do a snap single wire not a double fig8
¿Porque desde el principio no enseñan la posición correcta del alambre de amarrar ahí donde tiene la vuelta, porque orimero se ve una posición con mucho sobrante y despues al amarrar ya se ve que fue recorrido para hacerlo mas corto y poder amarrar.
Does not need to be this complicated, one quick tie around both and it's good. It's only good until the concrete dries, at that point the concrete will keep it in place.
Нет ето не правильно для арматурчик так нельзя долго будете делать и уволят смотри как таджики и узбеки делают неважно кто смотри и учись ето просто видео и .....
Esto no es de ingeniería ,este aparatito lo inventaron en el PERÚ Y TIENE POR NOMBRE : TORTOL TÉRMINO MUY USADO EN LOS TRABAJOS DE CONSTRUCCIÓN Y FUI YO QUIEN LO LLEVO A CHILE .
Простой одинарный узел, нормально держит! Сколько сданий построил,фундаментов и сейсмопоясов,досихпор стоят!Сейсмический район Центральной Азии,Алматы!
👌👍🤝
Кая разница главное при заливке чтоб все наместе так хоть жопой вяжи
Большой объём будешь 8 лет так вязать
😅
Nice technique!!! But I wonder is it possible to use electowelding to do the same job???
@@thiodorchalkias8906сварка ослабит арматуру
Аххаха такую дрочь показали, как будто эта проволка будет работать после заливки ...
@@Frod199.Все монолитные дома вязаны проволокой 0,8мм,она в 2 раза тоньше этой
Сразу видно в белой каске щеголяет😂
Why ain't you sporting your Army Helmet on the Front Lines. 🤨
@@PAUL-em4tjwhy ain't you
@@mikejohnson734 I'm not a War. YET !!!! BEWARE WHEN I AM ! 😡
Hc@@PAUL-em4tj
Какая разница как ты его вяжеш..турки одинаркой вяжут или пистолетом,проволока ничего не держит..просто фиксирует..
鉄筋屋さんならわかる。
ハッカの回しが逆だということを
鉄筋屋でもない自分でも反対では?とは思いました
ですよね
Он не понимает зачем вяжется арматура. В кратце, затем чтобы во время заливки она не сместилась. Вот и всё. Не надо ничего выдумывать.
It works if you have all the time in the world. On a construction site you would be canned in the first hour.
Я проработал арматурщиком почти двадцать лет и если бы я вязал как этот чел в ролики меня бы лишили пол зарплаты 😂
If you goof around like that on a Danish construction site binding iron for a concrete cast I guarantee you will be kicked out before the day is over
А что,у вас не связывают вообще проволокой арматуру?
I've been to quite a few construction sites in Denmark over the years, and get what you mean.
But with that being said, I think many if these tips is for those not in the industry, or those that doesn't have the advantage of picking up tricks from the oldtimers on the job.
Hav en god weekend!
Absofuckinglutely
There’s less people in the whole of Denmark than London so you can choose to do any time wasting thing you like. (JK, it would be nice if we could outsource the government of Britain to Denmark lol)
You obviously ain't Danish. 🤨
Арматура связывается лишь для того, чтобы при заливке бетона она не разъехалась
Speaking of "Reinforcements" , why ain't you on the Front lines ? 🤨
@@МаксМакс-е1н
Ошибаетесь уважаемый. Не вся арматура сваривается, как и не вся связывается. Зависит от конкретного проекта, нагрузок, бетона, марки самой арматуры.
@@naturihaus1744 арматуру категорически нельзя сваривать при заливке бетона. Почитай книги и узнай для чего нужна арматура в бетоне и какая её роль там
Thank you for sharing this technique ❤❤❤
Лишь бы мой начальник участка это не увидел 🙏
Главное чтобы заказчики не видели это видео
No, that is not the best way to tie that. That is half ass
As a certified expired fork lift license holder i can confirm this is the right way to make pancakes.
И так до китайской пасхи 1 плиту вязать
Nobody does this anymore.
Only if you want to do it by your self.
Ya know, they actually make the wire with loops on each end. And the hooked installation wire twist tool!
If we could attach pictures, I would send a picture of the actual installation tool!
Idk what you were doing but as an ironworker I can tell ya I’d be asking to see that tool and chucking it off the building. Klein pliers and do a snap single wire not a double fig8
Wowww mi abuelo me enseñó ese amarre en 1963. Entonces venía del futuro
No importa el proceso, siempre y cuando el resultado sea perfecto
Very slowly
that's old fashioned, just get it the machine and fired the most lazy guys on the crew because the machine can do just about 4 people at the same time
Сука почему я это раньше не увидел, когда меня заставляли крест на крест вязать в два захода😢
Мне дизайнер сказал хоть трусами вяжи и не надо всех этих манипуляций 🥰
結束線太くね?0.8mmの結束線をハッカーでくるくる巻けば一瞬で巻けるよ。
結束線では無いですね😂
I make that figure 8 tie way faster with my number 9 pliers will challenge anyone using this
땡 Right hand has to turn to the right.
Для тех, кто не торопится.
Well , your leaders are in a hurry to get you on the Front Lines. Why ain't you there ? 🤨
Faster with pliers and a roll of wire on your belt!
Hells yes! Concrete finisher for years and thats all we used was lines and reel...
Richtig, Kollege😮. Kurt
Wer nur 2cm zur Schalung hat, hat es Schwer und Verzinkter Draht ist es auch! Kurt
It's even faster to buy them pre made in a roll and use a spinny tool
@@JohnCoffins not even close lol
100 years technology already
Сразу вопрос, а для чего вяжется арматура??? И какой ценник на куб бетона???
THE REINFORCEMENTS ARE USED ON THE FRONT LINES. WHY AINT YOU THERE ? 🤨
Красавчик...... точно. Это и есть Правила
Now do it 400 times
Do that 10,000 times when the truck is on the way
To the beat...
1 and a (👏) and 3... (👏)
Down, up , around and do.. da twist
Tie Guys Twerk 😂
Вопрос прорабу: Куда ушло 4 года?
Прораб: так это, арматуру вязали 😅😅😅😅
😂😂👍🤗
i think there are differint type, depends on structure probably
¿Porque desde el principio no enseñan la posición correcta del alambre de amarrar ahí donde tiene la vuelta, porque orimero se ve una posición con mucho sobrante y despues al amarrar ya se ve que fue recorrido para hacerlo mas corto y poder amarrar.
Entre mas corto mas mejooooor 👍🏼
Headphone wires be like...
A lot of effort for something that has no structural value.. pretty though
DUH! What's the next episode, Proper butt wiping?
Целый мир держится на проволоках и на скотче😂
Esos amarres son para que no se muevan las varillas solo
Fazla kalan tel ile hirdavatciyi MUTLU edersin her yarım saatte bir ALIŞVERİŞ yaparsın A, HALİS
Незачем там мудрить!
Согласен
Cengami jest szybciej
Does not need to be this complicated, one quick tie around both and it's good. It's only good until the concrete dries, at that point the concrete will keep it in place.
نؤسهثهثق
Lol.10 years later hes rdy for concrete 😂😂😂
Milwaukee does it better
I never spent Tying it counterclockwise always clockwise
as a steel fixer myself we call that a box(cross)tie
Waste of tie wire if you ask me
Kręć w prowo a nie w lewo
Ok👍🤝👋
Just buy ties ? DUH
Well DUH! What's the next episode, Proper Ass wiping?
Nice tip 👏🎉
Thanks bro 👍🤝🤝
이 매듬방법은 견고합니다.
하지만 시간이 많이 걸려 인건비 비중이 맞지 않습니다.
Legătura asta ma dat afară de la grădiniță 😅😅😅
😂😂😂 в России ржавая арма и ржавая проволока и делают быстро
Солома, глина и навоз сподручнее
Mas simple batter fly
Yep. They make a tool for that, with pre cut and bent wire ties, but if you get paid by the hour, you are doing great.
Ye to idea purana hai koi Naya socho
По часовой стрелке нужно крутить, тогда не развяжется и крепче будет
正解。製造も右回り使用になっています
Страшный сон монтажника ЖБК
Видно что Болконский привязывает ещё неправильные стороны привязывать
Turn the twister the wrong side
Когда 500 вязок в день...
鐵線壓鐵線是無法把線之彈性拉出來,因此不止繞線錯誤還綁不緊
只是在鐵線打結罷了
千萬不學
繞線是要在受力方向繞一圈,如果受力是X和Y軸個別纏繞一圈,且不能鐵線壓鐵線,當多加練習後收緊鐵線時可以看到鐵線收縮捆住
收縮時鐵線是會動的,把鐵線彈性拉出來
Спасибо друг, эта полезная информация
Пожалуйста 🤝👋 Рад что понравилось 👍❤️❤️❤️
Looks like the wire is turned to far😊 and gets weak.
異型鉄筋の形状は日本と違う。この組み方工夫できそう!
Мынау бізден қалған ғо, 😂 арматурщик болып едім.
Моя бабушка вяжет быстее
У него полубому почасовая зарплата😂😂😂
Вы в смысле одни такие умники 😊
Очень сложно и долго , а польза одинакова с обычным креплением .
한글로 이딴 거 올리지마라
Io ho imparato a legare con le tenaglia ma anche così è ottimo
Вот мне урюки так навязали что я переделывал когда миксер уже ехал. А говорили все умеем!
Ход что делаешь он остаётся по бетону😂😂😂😂😂
NOSTROS AL 8 LOS ASEMOS CON UNA TENAZA. VI ESTA TECNICA A PERUANOS Q TRABAJAN ASI CON ESTE SISTEMA Y SOLO ACIAN EL CERO NO EL 8 COMO SE MUESTRA ACA..
.. ТАК В ЕГИПТЕ ДЕЛАЛИ 2000 ЛЕТ НАЗАД.
Good job🎉🎉
Thanks my friend 👋🤝❤️
閉めるは右開けるは左世界共通
Now, pour that concrete!
Hi
Прикольно?)))
😂😂😂
Но не факт, что быстрее!!!😅😅😅
Спасибо, как раз на носу стройка, всё думала,как же правильно скрутку делать?!❤
Рад что пригодилось👋😘❤️❤️❤️
Нет ето не правильно для арматурчик так нельзя долго будете делать и уволят смотри как таджики и узбеки делают неважно кто смотри и учись ето просто видео и .....
😂
Esto no es de ingeniería ,este aparatito lo inventaron en el PERÚ Y TIENE POR NOMBRE : TORTOL TÉRMINO MUY USADO EN LOS TRABAJOS DE CONSTRUCCIÓN Y FUI YO QUIEN LO LLEVO A CHILE .
Я делал чуть по другому, но принцип тот же, только быстрее было.
締める時は右回し
なんで?
А ты считал сколько времени и проволки уйдет на это это перебор
Te veo el patrón te ve que gastas alambre y fuiste 😂😂 desde salta la linda argentina 🇦🇷
I remember that things long time ago
Es la primera vez que veo atar con estaño😂😂😂
СПАСИБО ПАРЕНЬ.
У ТАКИХ КАК ТЫ, ЕСТЬ ДАР
ОТ БОГА..
УМ, ДОБРАТА , СОВЕСТЬ И
ЛЮБОВЬ К ЧЕЛОВЕКУ.
ЖДУ НОВЫХ УРОКОВ,_
КОЛЛЛЕГА.
Спасибо дружище 👋🤝 Мне действительно очень приятно 🤗❤️ Успехов Тебе 👍🤝❤️
Вязка лучше. сварка не то . при застывании бетон играет.
Eso sí es más viejo que la humanidad
Против часовой стрелки это не по технологии
Крючки и проволока,лучьше ни чего не придумали еще. А это все баловство.
不知道要蓋什麼?鋼筋的距離太大了!
Buenas tardes,ese amarrado es la pategallina