Thank you for this video. I am still looking for similar for the Cura Settings while using any printer in Klipper. Not just a specific Printer/Sonic Pad. This is as close as I have found so far. Thanks again
Thanks for this video. I’m fairly new to 3D printing and bought a sonic pad because I thought it would make life easier. I couldn’t be more wrong. I assumed you could create the g-code in Cura (although I don’t really know what I’m doing) and send it to the micro sd card, but put that in the USB adapter and plug that into the sonic pad instead of directly into the Ender 3 v2. It seems I am wrong.
Hi. At a high level what your saying is correct. The gcode is being created from Cura and its getting sent to the sonic pad. Cura just needs to know what settings are needed and i prefer to use the web browser over usb/sd.
When you copy and paste the start and end g-code how are you doing it? It won't let me paste anything in Cura. This may be a dumb question, but you breezed through it so fast I didn't see how you did it.
@@3DPrintscape I just received my sonic and your videos are a great guide for me! Thank you very much for such clear videos and walkthroughs! If you are new to these things, it can be very difficult and you give great detail and don't assume knowledge of your viewers Keep up the good work. I think you will have a very big following on TH-cam. Thank you again.
Hello ! If I have a cr-10 smart pro, what configuration should I use? By installing Kippler, is the printer already faster or should I configure something in the slicer?
Hi. Klipper allows the printer to be faster but you still have to tell it what speed to go at in the slicer. I would start with the cura profile for your printer then make the changes i mention in this video.
Apart from reducing the retraction length, do you know of any other changes (for the profile) for the Ender 3 Pro with the all metal hot-end (microswiss) running on Klipper when slicing on the Cura? I am assuming I can use the V2 profiles since they are both bowden tube (non-direct drive). Using CHEP Ender 3 Pro profile as of right now (pre sonic pad profiles). Will compare that too the V2 profiles later.
Hi. The big setting differences will be speed and retraction. The v2 profile should work fine since the only real difference is the silent board and screen.
Great video and I have everything setup, however whenever i try to print the nozzle is about 2.5mm above the print bed. I performed the probe calibration and it still won't work. If I try to adjust the bed height then my adjustment screws max out and I can't adjust enough. Any help or assistance would be great.
I have a Ender 3 S1 Plus with a sonic pad and there is no profile for this printer in the folder or information in the documentation on how to create a profile in Cura with this printer. Do i use the printer setting for the Ender 3 S1? Any help is appreciated. Thanks.
Just wondering if you would recomend me setting my g code to a different printer as i have installled a sprite extruder pro with cr touch and filament sensor on my ender 3 v2. Or do i still run stock v2 g code????
Hi. You dont need to set it to a different printer. Just add the g29 command after the g28 for the bed leveling and make sure you calibrate your e steps.
Greetings from England. I thought the same thing as you @LP, but then I’m new to all this g-code stuff. I’d like to learn how to design & print my own items. At the moment I’m just getting stl’s from thingyverse and running them through Cura and hope for the best. I bought a sonic pad because I thought it would make things easier. Seems like I’ve still got a lot to learn.
Hi. Are you running the sonic pad? If so, the ones i call out here are probably a good starting point. Just make sure you set the build plate size correctly in the slicer.
Hi. I dont have one for the S1 Pro but the one i have for for the v2. It shouldn't be too much different as far as speeds and everything go to start with. You will need to tweak things based on the printers behavior though.
What do you mean by starting with the ones for Ender? The Standard Profile who came with? I found a Profile on the Creality Print Slicer, but honestly I don't like this Slicer that much. Do you think I can copy that?@@3DPrintscape
Thank you for this video. I am still looking for similar for the Cura Settings while using any printer in Klipper. Not just a specific Printer/Sonic Pad. This is as close as I have found so far. Thanks again
You're welcome!
Thanks for this video. I’m fairly new to 3D printing and bought a sonic pad because I thought it would make life easier. I couldn’t be more wrong. I assumed you could create the g-code in Cura (although I don’t really know what I’m doing) and send it to the micro sd card, but put that in the USB adapter and plug that into the sonic pad instead of directly into the Ender 3 v2. It seems I am wrong.
Hi. At a high level what your saying is correct. The gcode is being created from Cura and its getting sent to the sonic pad. Cura just needs to know what settings are needed and i prefer to use the web browser over usb/sd.
Very helpful thank you, I thought I hook up the Sonic pad and it prints faster, I didn't know I had to make a custom setting.
Hi. Ya the print speed is determined by what is in the slicer settings.
Thank you! Great Video! Very Helpful!
You're welcome!
When you copy and paste the start and end g-code how are you doing it? It won't let me paste anything in Cura. This may be a dumb question, but you breezed through it so fast I didn't see how you did it.
Hi. Sorry, i was just using ctrl+v .
Testing with settings for the Ender 3 v2 would be awsome to get me started! Thanks for this video though!
Hi. I will try to do some more testing soon.
@@3DPrintscape I just received my sonic and your videos are a great guide for me! Thank you very much for such clear videos and walkthroughs! If you are new to these things, it can be very difficult and you give great detail and don't assume knowledge of your viewers Keep up the good work. I think you will have a very big following on TH-cam. Thank you again.
thanks for the video, any idea if they provide profiles for the ender 5 plus?
Hi. The Ender 5 plus has an 8-bit board so its not supported.
Hello ! If I have a cr-10 smart pro, what configuration should I use? By installing Kippler, is the printer already faster or should I configure something in the slicer?
Hi. Klipper allows the printer to be faster but you still have to tell it what speed to go at in the slicer. I would start with the cura profile for your printer then make the changes i mention in this video.
Apart from reducing the retraction length, do you know of any other changes (for the profile) for the Ender 3 Pro with the all metal hot-end (microswiss) running on Klipper when slicing on the Cura? I am assuming I can use the V2 profiles since they are both bowden tube (non-direct drive). Using CHEP Ender 3 Pro profile as of right now (pre sonic pad profiles). Will compare that too the V2 profiles later.
Hi. The big setting differences will be speed and retraction. The v2 profile should work fine since the only real difference is the silent board and screen.
Awesome. And thank you very much for your videos and clear technical explanations. Much appreciated.
@3DPrintscape how fast have you printed on the ender 3 pro without losing too much quality? 120 mm/s?
Great video and I have everything setup, however whenever i try to print the nozzle is about 2.5mm above the print bed. I performed the probe calibration and it still won't work. If I try to adjust the bed height then my adjustment screws max out and I can't adjust enough. Any help or assistance would be great.
Hi. It sounds like the z offset isnt set right. What value did you come up with for the offset?
Does this work also an a Ender 3 Max Neo? In case i put the right Bedsize in?
Hi. I think it would work.
Did you get a profile setup for your ender 3 pro? I'd like to setup mine
Hi. Ya, its pretty much the same as the ender 3 v2
Thank you for your response. I will go with this thanks to your support.@@3DPrintscape
I have a Ender 3 S1 Plus with a sonic pad and there is no profile for this printer in the folder or information in the documentation on how to create a profile in Cura with this printer. Do i use the printer setting for the Ender 3 S1? Any help is appreciated. Thanks.
Hi. I would start with the closest printer to the one you have in terms of specs, so the S1 is probably a good place to start.
Just wondering if you would recomend me setting my g code to a different printer as i have installled a sprite extruder pro with cr touch and filament sensor on my ender 3 v2. Or do i still run stock v2 g code????
Hi. You dont need to set it to a different printer. Just add the g29 command after the g28 for the bed leveling and make sure you calibrate your e steps.
If you're going to be using the Sonic pad which runs Klipper, why did you choose the Merlin G-Code during set-up?
Hi. There isnt a flavor for Klipper that im aware of. The g-code is mostly the same minus a few commands.
Greetings from England. I thought the same thing as you @LP, but then I’m new to all this g-code stuff. I’d like to learn how to design & print my own items. At the moment I’m just getting stl’s from thingyverse and running them through Cura and hope for the best. I bought a sonic pad because I thought it would make things easier. Seems like I’ve still got a lot to learn.
I have a ender 3 max with a cr touch and dont really under stand what printer settings i shoild use in my slicer.
Hi. Are you running the sonic pad? If so, the ones i call out here are probably a good starting point. Just make sure you set the build plate size correctly in the slicer.
Do you have a guide for the BTT Pad7 running on Ender 3 S1 Pro?
Hi. I dont have one for the S1 Pro but the one i have for for the v2. It shouldn't be too much different as far as speeds and everything go to start with. You will need to tweak things based on the printers behavior though.
Anything for the Ender 5 plus?
Hi. I don’t think there was anything for it. The ender 5 plus has an 8 bit board which won’t work.
I have an Ender 5 S1, which Profiles can I use therefore?
Hi. I would start with the one for the Ender and modify it from there.
What do you mean by starting with the ones for Ender? The Standard Profile who came with? I found a Profile on the Creality Print Slicer, but honestly I don't like this Slicer that much. Do you think I can copy that?@@3DPrintscape
Cura 5.6 has the standard profile for the Ender 5 S1 in it, you should start with that.@@raffaelegambardella4011