I Love how easy this th-cam.com/users/postUgkxvAj3godqGAIP5rApM1laH767JGtPG1-h carrier is to adjust from my friend to me taking turns holding the baby! It provides great support on my back too! This has definitely made shopping easier! I always get asked where I get it too!
Is it possible to swap out just the U-joint near the diff without swapping the entire driveshaft? Like on my truck I was able to just pop off a clip and swap the U-Joint in the parking lot. Just seems wasteful that the entire driveshaft is junk now just because the joint is a little wiggly.
Same harbor freight pullers I have ! Lol I took an wd-40 the threads an light anti-seize prior to use an ran it up an down serval times an they have held up ok. I used them on same exact thing lol . Guess I got lucky .
I just did my one (on an X3) BMW. After loading it up on the puller using a 10 tonne hydraulic bearing puller) it still required a tap using an old wood chisel between the shaft and the inner race...bang...
You better Grease the threads on that puller if you want to use it a couple more times get the cut saw three and a half inch angle grinder bada bing bada boom or if you want to have fun get in there chisel on an angle little on one side little on the other walk it right off I used to do this the big trucks or warm it up
Two of the many things I have learned in my almost half century of repairing cars are 1)If you don't have what you need tool wise and can borrow it, do so. but if you think or know you will need it again, buy it. 2)If you buy the best you will only have to buy it once.
Or do what I do. Buy that tool anyway. And then sell it as ‘used only once’ on eBay afterwards. I usually get most of my money back. Obviously I only do this with tools that would very rarely get used.
I just cut mine off with an angle grinder when I replaced the bearing on my e39. New one went on pretty easy. That vid wasn't up to your normal standards.
Selam. BMW X5 e53 code 2003 model 4.4i kullanıyorum. Özellikle aracımın motoru sıcakken Aracımı D ye alırken one atılma,isteksizlik ve dururken 5 kilometre civarı öne atlama yapıyor . Lütfen cevap verirmisiniz?
Definitely lube the treads, grease or antiseize. Depending on the situation Lube the end of the threaded rod also where it is going to spin on the work piece.
This crap tool wasn't designed for use on BMW... It happened to me couple of times as well... However, If I you need tool for one time use, you can rent it from many the automotive Stores. Worked for me.
I dislike taking off the driveshaft ony e30. Such a pain in the butt especially if you have to be laying on the floor. My e30 center support bearing shield needs to be replaced because it makes a grinding noise when im in the higher rpms.
Hi Nathan,I'm after your help,I've recently bought an x3 which had a slight rumble noise on acceleration,on further inspection it appears that there isn't a front propshaft,but obviously it should be there,I'm going to buy one and put it on,but would this explain the rumbling noise in the lower gears and clunking...many thanks nigel
I can't believe a little old BMW has to have a carrier bearing. We drive an F250 four-wheel drive pickup 8 ft bed extended cab it don't need no carrier bearing. I hope my wife's 2009 328i don't have one it's just more pieces of s*** to fix. I change my BMW emblem, two POS piece of s***
![[Eng Sub] BMW E46 Flex disc (guibo) and drive shaft center support bearing replacement DIY](http://i.ytimg.com/vi/cUH9_4Zm9Xg/mqdefault.jpg)
![เปิดบ้าน พี่ตูน Bodyslam หลังใหม่คนแรก ที่ภูเก็ต l [Nickynachat]](http://i.ytimg.com/vi/flFwcmyDQSk/mqdefault.jpg)
I Love how easy this th-cam.com/users/postUgkxvAj3godqGAIP5rApM1laH767JGtPG1-h carrier is to adjust from my friend to me taking turns holding the baby! It provides great support on my back too! This has definitely made shopping easier! I always get asked where I get it too!
Did I miss something ? How did you get it off ?
And that showed us absolutely nothing !
I'm confused, how is this a video on how to replace? You didn't even show it coming fully off let alone how to install the new one.
Is it possible to swap out just the U-joint near the diff without swapping the entire driveshaft? Like on my truck I was able to just pop off a clip and swap the U-Joint in the parking lot. Just seems wasteful that the entire driveshaft is junk now just because the joint is a little wiggly.
Why would you show an incomplete video? Why start if you're not going to finish it? That sucks!
You might be a tooth off because you didn't market before you took it off. check the u-joints laying flat on a table and you will know
Same harbor freight pullers I have ! Lol I took an wd-40 the threads an light anti-seize prior to use an ran it up an down serval times an they have held up ok. I used them on same exact thing lol . Guess I got lucky .
I just did my one (on an X3) BMW. After loading it up on the puller using a 10 tonne hydraulic bearing puller) it still required a tap using an old wood chisel between the shaft and the inner race...bang...
You better Grease the threads on that puller if you want to use it a couple more times get the cut saw three and a half inch angle grinder bada bing bada boom or if you want to have fun get in there chisel on an angle little on one side little on the other walk it right off I used to do this the big trucks or warm it up
Two of the many things I have learned in my almost half century of repairing cars are 1)If you don't have what you need tool wise and can borrow it, do so. but if you think or know you will need it again, buy it. 2)If you buy the best you will only have to buy it once.
Or do what I do. Buy that tool anyway. And then sell it as ‘used only once’ on eBay afterwards.
I usually get most of my money back.
Obviously I only do this with tools that would very rarely get used.
OMG what a terrible video, no shot of getting it off!
I just cut mine off with an angle grinder when I replaced the bearing on my e39. New one went on pretty easy. That vid wasn't up to your normal standards.
Nice diy. Very knowledgeble. 😂
Selam. BMW X5 e53 code 2003 model 4.4i kullanıyorum. Özellikle aracımın motoru sıcakken Aracımı D ye alırken one atılma,isteksizlik ve dururken 5 kilometre civarı öne atlama yapıyor . Lütfen cevap verirmisiniz?
Does anyone know if the drive shaft carrier center support bearing same for a manual transmission as an automatic.. car in question is a 98 bmw 528??
A little silver anti seize on the puller threads will some times help.
Definitely lube the treads, grease or antiseize. Depending on the situation Lube the end of the threaded rod also where it is going to spin on the work piece.
This crap tool wasn't designed for use on BMW... It happened to me couple of times as well... However, If I you need tool for one time use, you can rent it from many the automotive Stores. Worked for me.
I dislike taking off the driveshaft ony e30. Such a pain in the butt especially if you have to be laying on the floor. My e30 center support bearing shield needs to be replaced because it makes a grinding noise when im in the higher rpms.
Hi Nathan,I'm after your help,I've recently bought an x3 which had a slight rumble noise on acceleration,on further inspection it appears that there isn't a front propshaft,but obviously it should be there,I'm going to buy one and put it on,but would this explain the rumbling noise in the lower gears and clunking...many thanks nigel
I can't believe a little old BMW has to have a carrier bearing. We drive an F250 four-wheel drive pickup 8 ft bed extended cab it don't need no carrier bearing. I hope my wife's 2009 328i don't have one it's just more pieces of s*** to fix. I change my BMW emblem, two POS piece of s***
Most Trucks use solid shaft,Why would you buy it then? Your wife's 328i is going to have all the bm's specialty's
Wow to much pressure to pull that part probably a lil bit of Pb blaster and i think work
I did mine . I'm sorry I didn't do the rubber thingy.show how to do the ujoint lol
I suppose you could hack it off with an angle grinder
Did I just see a circlip flying off
never seen a shop with enough tools much less too many
Nice job with that marking, lol
A cut off wheel is much cheaper
It does the job
Fail
FIRST!!
Great quality video thanks!!
Another great video, thanks 😁
yo