The spring you linked to and used is an ak-blastermod brand spring, it's not made by worker and not sold by other retailers of worker products unless those retailers are getting the spring from ak-blastermod.
You're right, I just double checked Workers site to see the spring they offer and it's clearly a different spring. I've updated the Video name and description to correct this. Thanks for pointing that out!
@@VileMods hey man. I got my kits and installed them all thanks to you... although I cannot for the like of me figure out what the little green oring is for? Is this just an extra? Its displayed in your video next the the kit on the right.... please help lol..
@@YourMajesty100 It might just be a spare o-ring. The only green o-rings on these kits go on the pusher itself. There should be one on the front of the pusher head, and then 2 more on the back where it mates to the collapsible piece.
@@VileMods look at 5:42 it's that little green oring to the left of the spring and to the right on the kit... it seems smaller then any of the other orings.... that's the one I'm referring to.. just couldnt find a place for it to go and the only green on is the one already installed on the piece you spoke of and it seems alot smaller when I took it off and compared the two
@@VileMods Worker has a 12 kg spring for the nexus pro on their site. I ordered both metal kits and that spring but I cannot get that spring to fit on my nexus pro plunger at all. It has a flat sharp edge on both sides and actually scraped off small pieces of my Nexus plunger in my attempt to put it on. Please help
Hey man, I think I was the one that commented on Brads video about the Ceda with the spacer. I had to prime it by putting the butt of the blaster on the ground then put my whole weight into the prime - totally not war practical, and my spring is bent to all hell now! Anyway, just wanted to say it’s refreshing seeing a TH-cam firstly acknowledge what others have done, and then not just spitting out the same content... keep this up mate!
Hey! So I saw that in the Cid you said you didn't have much a perfect seal on your nexus. I actually know where it may be and how you could potentially fix it. For my nexus all the seals of the blaster kinda just went out so I had no seal on it at all. After months of looking on how to better the seal I found it. Basically what I did was take out all the orings of the system and put Teflon tape on the underside of each o-ring including the plunger. I put enough Teflon to where it fits into each specific part but it fits tightly same goes for the plunger I put enough Teflon tape to cause the plunger to have a tight but not too tight fit it was still able to move back and forward through the plunger tube but it required a little bit more force to move it. After putting enough lubricant I was able to move every part of the system a little bit more easier. After all this I did the thumb-on-barrel test and it kept a 101% seal :D I haven't gotten FPS numbers but I'm sure that it's hitting high numbers a lot more consistent. Also when putting Teflon you can choose weather to put Teflon on the underside of the pring that goes into the dart gate, for me I didn't since I had the full metal worker kit it, the green o ring that comes on that part already gives a heat enough seal, the main parts you really want to focus on when making a perfect seal is the telescoping pieces, I've noticed that on a stock nexus pro those seals specifically can be very wonky. Hope I explained this well and I hope this helps!
They're good blasters with a lot of tune-ability. Best way to look at them is being an introduction into the pro-stock/super-stock level without shelling out a couple hundred for a custom blaster like a TC/Caliburn or one of the many Pro-Flywheelers out there.
i just LOVE the nexus pro... even out of the box with lilbit of tape to seal stock barrel to the dartgate, a cheap washer mod between spring and spring guide. Airsoft AEG Springs drop in for adjustable FPS within seconds. i am going to check out the 25cm x 1.30cm barrel from akblastermods combined with a small worker scar inside the modded muzzle break. really really nice blaster with cheap tunability for hi-performance foam flinging
It's pretty straight forward, Bradley's video had really good detail on installation. I do suggest adding something like Teflon tape to the barrel before putting it into the breech block.
Yeah I've been meaning to get those caps actually. The 190ish FPS is perfect for my wars and the nice thing is I don't need any spacers to keep that number. Glad you're liking the content!
I had tennis elbow for a week after putting around 150 darts through my nexus with a turf spring. Mine is also very warped. I already have a brass barrel and I slammed buy on the spring.
Yeah that's similar that what I had. It also pinched a nerve in my shoulder which still gives me a bit of trouble but it'll get better as time goes on. This spring is way better for the prime compared to that Turf spring.
I don't like using springers above 16kg because of that issue. A decent brass setup can usually get similar results using a 12-14kg spring as well. HPA is nice, you just get a sore finger from spamming darts downrange :P.
Looks great especially with purple magazines great numbers too. The only thing left to do is wait for COVID to die and make your enemies fear you on the battle field
So it was just a piece of 1/2" aluminum tubing cut to about a 1" length. It's about the same as the OOD 175 FPS back cap. With the spacer it's normal to see around a 20 FPS increase on just about any internal combo you're running (stock internals/spring or modded internals/spring).
@@captaintony6879 I took the spacer out after recording since my local group cap was 200 FPS. I didn't notice it bending the spring but that may just be the fact I didn't run it for very long with the spacer in.
That's the Worker short dart adapter, super cheap and sleek. OOD listing for it --> outofdarts.com/collections/mags-grips-stocks-2019/products/worker-short-dart-adapter-3-colors?variant=14267449442346
At the beginning of the video you have a worker 4pt scar before the install? And at end of video, after the install, you have the same worker scar on the 17/32 red barrel? So that scar is compatible with stock nexus pro and and to a 17/32 barrel?
Well I would have linked it to you but it's been removed from Amazon. It was originally a Tacpool brand stock and the only other one I can find that looks similar is in a kit by Tacfire - AR15 Buffer Tube kit.
Hi there @Vile Mods Just installed those two worker mods on my NP. But I have a problem with it. I don't know if it's the barrel, the breech or both. But EVERYTIME I load up a magazine, the first Dart is never coming out. I need to prime a second time, before that Dart comes out. And mostly it doesn't fly very far. I used your trick and sealed between the barrel and the breech. But that didn't help. I am really thinking of building back to the stock breech and barrel, if this keeps happening. Because now, waffle head and Acufake darts do also jam basically every time.
Yeah I never use larger headed darts like Waffles or Accufakes. I've never had luck with them in any springer with a long barrel. If it's something you use more often then yeah, going back to the stock setup is probably best.
I have that same spring and i think my nexus is probably a faulty blaster as it doesnt prime consistently with the 12kg unless i really jam the grip back. And if i use a spacer with the spring, the blaster doesnt prime at all. The ceda spring just doesnt work in my blaster either. It's so frustrating because i dont know whats wrong or how i would fix it.
Weird, I haven't heard of that problem before. Have you opened the blaster to see what might be causing that? Was it harder/chuncky to prime before changing the spring?
@@rookyandb yeah i put that orange piece back on the spring. I've open up my blaster numerous times for mods and maintainence but nothing has shown any problems internally. I've checked the catch and there's nothing that i can see that's wrong with it.
@@afterburn819 Maybe there's some flashing on the plastics that need to be cleaned off? Could possibly lubricate the internal priming bar as well? Without having it in my hands it's kinda hard to narrow it down.
I was looking into this 12kg spring, a monkeemods aluminum barrel, a worker scar and a few other miscellaneous things. What is the outter diameter of the stock barrel? Also what's the length of the worker barrel included in the kit?
16mm OD, that's pretty standard now for aluminum barrels in the hobby. Barrel measures out to 310mm according to Worker but you can go with 300mm and still get similar numbers.
So the shoulder stock I can't find anymore unfortunately. I got it off Amazon and it's been removed. The spacer is just a 1" long piece of aluminum tubing, you can also just CPVC.
JUST found your channel. I hope your name is a reference to the Purple Mandalorian, with the ShoulderCannon, (and knee, and fist, weapons in the ReMake). Zero from X is MY favorite character.
@@VileMods You won't look back after getting an adjustable one IMO. I've tried worker, MM and some others but after using BT adjustable scars I haven't looked back. Tuned barrel length plus an adjustable scar and you'll be getting very nice grouping out to 120ft or so with the Nexus Pro.
I hate linking it cause the address is stupidly long... and I'm to lazy to do a tiny url. XD But look up Feyachi RS-30 Reflex Sight on Amazon, it's very similar, if not the same one. I got it a while ago and there's a few other branded ones that look the exact same.
I know this vid is pretty old at this point, but where is that low profile halfdart magwell from? Can’t find it anywhere or even files for it… if anyone could point me in the right direction that would be epic
Hey Maxt, that's just the simple Worker half-dart adapter you can get on Out of Darts website for under $4 outofdarts.com/products/worker-short-dart-adapter-3-colors
So I'm a bit surprised at what I got after running ten rounds through the chrono (these were used AF darts). No spacer was used. Results in order: 210, 211, 215, 223, 212, 209, 211, 210, 224, 219
@@rextonhart Yep, just swapped the spring out and checked it with the kit in. I originally was seeing 220s with just this spring but the ranges varied down to low 170s and high of 230s. The biggest thing the kit provides is consistency. Not to mention, this spring may not be optimal after my original use and the fact that it's warped so badly now might be affecting it's performance.
Hi for your information... There is now a 2nd metal kit for the Nexus Pro. It includes a metal air chamber, a metal priming bar, a metal catch and a metal mag release lever. AKBlasterMod is offering the set in the colors of silver and red. But you need to combine this new kit with the kit that is shown in this video the get the complete tuning experience. You can even use a 16 kg spring then.
I just looked at the kit and may be getting it. I'm a bit disappointed that they didn't redesign the telescoping piece and make the blaster short dart only. This could have been an opportunity to give a slight increase of performance by reducing dead space, remove the slop when priming it, and reducing the priming length.
@@VileMods Same opinion here. I already contacted AKBlasterMod to offer a "one piece" pusher... I hate the telescoping pusher. You can unscrew the head of the pusher. Should not be so hard to make a longer pusher body. Time will tell.
Should I get a nexus pro or stryfe (might look into the stryfe killer if I can find one). It's for me and my gf as we're having nerf wars in house now lol
Yeah Nexus hits in the 140s to 150s out of the box so close up shots like that might hurt. If you can get a Dart Zone Spectrum it's in the 90s out of the box and has a lot of support right now especially since you can still buy them off the shelf at Walmart.
@@VileMods I went out and bought 2 nexus pros. Me and my gf are in danger now 🤪. But I also have 2 spectrums on the way. The Nexus is so much fun. Thank you btw for the input.
@@oso999x I'm not sure on that one. Only down side to using half darts on a flywheeler is the fact that they don't get the best performance. Nice if you only want to use one ammo type but it'll get lower FPS since it doesn't have contact with the flywheels for as long.
I'm acturally trying to get my nexus pro down some, hopefully with just a lighter spring. I want to take it to an HvZ and other 130fps games/events.I could prime it and leave it primed for a time, but... I don't want to stress the rest of the catches and shell. Adventure Force blasters are kinda cheap. Thanks walmart. I can feel the 10 dollar difference in the Max line haha.
The spring you linked to and used is an ak-blastermod brand spring, it's not made by worker and not sold by other retailers of worker products unless those retailers are getting the spring from ak-blastermod.
You're right, I just double checked Workers site to see the spring they offer and it's clearly a different spring. I've updated the Video name and description to correct this. Thanks for pointing that out!
@@VileMods hey man. I got my kits and installed them all thanks to you... although I cannot for the like of me figure out what the little green oring is for? Is this just an extra? Its displayed in your video next the the kit on the right.... please help lol..
@@YourMajesty100 It might just be a spare o-ring. The only green o-rings on these kits go on the pusher itself. There should be one on the front of the pusher head, and then 2 more on the back where it mates to the collapsible piece.
@@VileMods look at 5:42 it's that little green oring to the left of the spring and to the right on the kit... it seems smaller then any of the other orings.... that's the one I'm referring to.. just couldnt find a place for it to go and the only green on is the one already installed on the piece you spoke of and it seems alot smaller when I took it off and compared the two
@@VileMods Worker has a 12 kg spring for the nexus pro on their site. I ordered both metal kits and that spring but I cannot get that spring to fit on my nexus pro plunger at all. It has a flat sharp edge on both sides and actually scraped off small pieces of my Nexus plunger in my attempt to put it on. Please help
Thank you for sharing the teflon tape treatment for better air seal, whoever you are. Thanks!
Hey man, I think I was the one that commented on Brads video about the Ceda with the spacer. I had to prime it by putting the butt of the blaster on the ground then put my whole weight into the prime - totally not war practical, and my spring is bent to all hell now!
Anyway, just wanted to say it’s refreshing seeing a TH-cam firstly acknowledge what others have done, and then not just spitting out the same content... keep this up mate!
Yeah, totally not running that monster! Glad you like the content.
High fps springers aren't for everyone. You have to have enough strength to prime high spring loads. Not really for children
you gotta get jacked so then the ceda with spacer feels like a rampage prime
Awesome mod video with thorough tests! You have a new sub!
you are so close to 500 subs! Great vid btw
Hey! So I saw that in the Cid you said you didn't have much a perfect seal on your nexus. I actually know where it may be and how you could potentially fix it. For my nexus all the seals of the blaster kinda just went out so I had no seal on it at all. After months of looking on how to better the seal I found it. Basically what I did was take out all the orings of the system and put Teflon tape on the underside of each o-ring including the plunger. I put enough Teflon to where it fits into each specific part but it fits tightly same goes for the plunger I put enough Teflon tape to cause the plunger to have a tight but not too tight fit it was still able to move back and forward through the plunger tube but it required a little bit more force to move it. After putting enough lubricant I was able to move every part of the system a little bit more easier. After all this I did the thumb-on-barrel test and it kept a 101% seal :D I haven't gotten FPS numbers but I'm sure that it's hitting high numbers a lot more consistent. Also when putting Teflon you can choose weather to put Teflon on the underside of the pring that goes into the dart gate, for me I didn't since I had the full metal worker kit it, the green o ring that comes on that part already gives a heat enough seal, the main parts you really want to focus on when making a perfect seal is the telescoping pieces, I've noticed that on a stock nexus pro those seals specifically can be very wonky. Hope I explained this well and I hope this helps!
Very insightful! Might have to get me a nexus pro now!
They're good blasters with a lot of tune-ability. Best way to look at them is being an introduction into the pro-stock/super-stock level without shelling out a couple hundred for a custom blaster like a TC/Caliburn or one of the many Pro-Flywheelers out there.
Not sure why it took me a month to find this, but good video. Living closer to China geographically possibly has its benefits with shipping. 😉
Yeah I'm sure it does. Still had a good video and made it easier for me to direct people to your video for the install of the kit.
Bradley Phillips, the Chris Kyle of nerf sniping.
Nice one. This blaster needed a metal kit. Nice job finding the air leaks.
Yeah, those were the last things needed to really get the consistency that I've been looking for.
i just LOVE the nexus pro... even out of the box with lilbit of tape to seal stock barrel to the dartgate, a cheap washer mod between spring and spring guide. Airsoft AEG Springs drop in for adjustable FPS within seconds.
i am going to check out the 25cm x 1.30cm barrel from akblastermods combined with a small worker scar inside the modded muzzle break.
really really nice blaster with cheap tunability for hi-performance foam flinging
Just got this same kit from AK, including the spring...it'll be my first mod. Hope it's not too difficult!
It's pretty straight forward, Bradley's video had really good detail on installation. I do suggest adding something like Teflon tape to the barrel before putting it into the breech block.
Out of darts has a end cap system you mite like better than your cap , each end cap is different fps. Liked your show thanks for your time.
Yeah I've been meaning to get those caps actually. The 190ish FPS is perfect for my wars and the nice thing is I don't need any spacers to keep that number. Glad you're liking the content!
I get mid 240's with a Ceda spring, 1/4 spacer, 17/32 brass barrel, while using new Pro dart steffans!
(Highest was 256!)
Nice video. 🔥🔥🔥
I had tennis elbow for a week after putting around 150 darts through my nexus with a turf spring. Mine is also very warped. I already have a brass barrel and I slammed buy on the spring.
Yeah that's similar that what I had. It also pinched a nerve in my shoulder which still gives me a bit of trouble but it'll get better as time goes on. This spring is way better for the prime compared to that Turf spring.
I don't like using springers above 16kg because of that issue. A decent brass setup can usually get similar results using a 12-14kg spring as well. HPA is nice, you just get a sore finger from spamming darts downrange :P.
ak-blastermod isn't able to ship to USA right now. Where can I get this spring otherwisae?
Yeah that's a tough one, I don't know of anyone in the states that partner with AKBM to distribute here unfortunately. :(
Would like a metal breach in my aeon
love it. what stock is that? thanks
Looks great especially with purple magazines great numbers too. The only thing left to do is wait for COVID to die and make your enemies fear you on the battle field
What spacer did you use for your testing and how much did it improve performance over stock internals
So it was just a piece of 1/2" aluminum tubing cut to about a 1" length. It's about the same as the OOD 175 FPS back cap. With the spacer it's normal to see around a 20 FPS increase on just about any internal combo you're running (stock internals/spring or modded internals/spring).
@Vile Mods did you get any spring bend from using the spacer because mine began to bend and become crooked once I used the spacer
@@captaintony6879 I took the spacer out after recording since my local group cap was 200 FPS. I didn't notice it bending the spring but that may just be the fact I didn't run it for very long with the spacer in.
Where did you get that short black magazine adapter? Looks amazing 👏 like that
That's the Worker short dart adapter, super cheap and sleek. OOD listing for it --> outofdarts.com/collections/mags-grips-stocks-2019/products/worker-short-dart-adapter-3-colors?variant=14267449442346
@@VileMods Awesome , thank you so much for the link. Looks great 👍
At the beginning of the video you have a worker 4pt scar before the install? And at end of video, after the install, you have the same worker scar on the 17/32 red barrel? So that scar is compatible with stock nexus pro and and to a 17/32 barrel?
What stock do you use? I've been looking for a replacement for the stock and I really like yours
Well I would have linked it to you but it's been removed from Amazon. It was originally a Tacpool brand stock and the only other one I can find that looks similar is in a kit by Tacfire - AR15 Buffer Tube kit.
Do you know what the little green O-Ring in the kit is for? I have no idea what it’s purpose is or where it goes
Hi there @Vile Mods
Just installed those two worker mods on my NP. But I have a problem with it. I don't know if it's the barrel, the breech or both. But EVERYTIME I load up a magazine, the first Dart is never coming out. I need to prime a second time, before that Dart comes out. And mostly it doesn't fly very far.
I used your trick and sealed between the barrel and the breech. But that didn't help. I am really thinking of building back to the stock breech and barrel, if this keeps happening.
Because now, waffle head and Acufake darts do also jam basically every time.
Yepp, back to the stock barrel and breech. Works like a charm.
Yeah I never use larger headed darts like Waffles or Accufakes. I've never had luck with them in any springer with a long barrel. If it's something you use more often then yeah, going back to the stock setup is probably best.
What scar are you using link pls?
I have that same spring and i think my nexus is probably a faulty blaster as it doesnt prime consistently with the 12kg unless i really jam the grip back. And if i use a spacer with the spring, the blaster doesnt prime at all. The ceda spring just doesnt work in my blaster either. It's so frustrating because i dont know whats wrong or how i would fix it.
Weird, I haven't heard of that problem before. Have you opened the blaster to see what might be causing that? Was it harder/chuncky to prime before changing the spring?
Kind of a dumb question but, did you put orange cap on the replacement springs?
@@rookyandb yeah i put that orange piece back on the spring. I've open up my blaster numerous times for mods and maintainence but nothing has shown any problems internally. I've checked the catch and there's nothing that i can see that's wrong with it.
@@afterburn819 Maybe there's some flashing on the plastics that need to be cleaned off? Could possibly lubricate the internal priming bar as well? Without having it in my hands it's kinda hard to narrow it down.
I was looking into this 12kg spring, a monkeemods aluminum barrel, a worker scar and a few other miscellaneous things. What is the outter diameter of the stock barrel? Also what's the length of the worker barrel included in the kit?
16mm OD, that's pretty standard now for aluminum barrels in the hobby. Barrel measures out to 310mm according to Worker but you can go with 300mm and still get similar numbers.
What barrel do you put on that I'm trying to find one
Is the barrel diameter 16mm? or 17/32? Or some other? Thanks in advance.
Where did you get the shoulder stock and spacer from
So the shoulder stock I can't find anymore unfortunately. I got it off Amazon and it's been removed. The spacer is just a 1" long piece of aluminum tubing, you can also just CPVC.
JUST found your channel. I hope your name is a reference to the Purple Mandalorian, with the ShoulderCannon, (and knee, and fist, weapons in the ReMake).
Zero from X is MY favorite character.
Funny enough, it's based off a character that was highly influenced by Boba Fett but came out in the mid 90s.
Sweet. I've actually made a short AnimatedEmoji for Discord, of Zero teleporting in to fire a MEGAdart.
@@PirateJohnson Did we just become enemies!? (best friends) Which discord was this in?
LOL.
Hi, does the worker metal kit can be used for dart zone max stryker?
I’ve done everything I can think of and I still can’t get a thumb over the barrel pull the trigger release the pop air seal.
What the small black rod for
I mean your Nexus is kinda kind of just basically upgraded in the beginning when you're talking about how tricked out it is?
What space did you use with the 12g spring?
I was running a 1" spacer.
@@VileMods thank you
Which scar barrel are you using ?
That's the slip on one from Worker. I'm looking at getting one of the smaller adjustable scar barrels later.
@@VileMods You won't look back after getting an adjustable one IMO. I've tried worker, MM and some others but after using BT adjustable scars I haven't looked back. Tuned barrel length plus an adjustable scar and you'll be getting very nice grouping out to 120ft or so with the Nexus Pro.
May i know how long about spacer. I want to make one.
It's a 1" spacer, you can use either CPVC or Aluminum tubing.
What kinda optic are you using?
I hate linking it cause the address is stupidly long... and I'm to lazy to do a tiny url. XD
But look up Feyachi RS-30 Reflex Sight on Amazon, it's very similar, if not the same one. I got it a while ago and there's a few other branded ones that look the exact same.
I know this vid is pretty old at this point, but where is that low profile halfdart magwell from? Can’t find it anywhere or even files for it… if anyone could point me in the right direction that would be epic
Hey Maxt, that's just the simple Worker half-dart adapter you can get on Out of Darts website for under $4 outofdarts.com/products/worker-short-dart-adapter-3-colors
So the smaller, lighter spring, shorter spring (worker) is better than the bigger, heavier, and longer spring (ceda)…? That’s just mind boggling
What grease do I use
Personally, I use the Super Lube 56204 which isn't as thick as the Super Lube 92003 that others tend to use.
I tried using the 12kg spring in my nexus, and it would not fit in my nexus
Do you have a link to were you got the spring
Yep, in the video description. I found the best price was from AK-Blastermods
@@VileMods yea I found it commented before looking thanks great video keep em coming
Can you chrono the turf spring
So I'm a bit surprised at what I got after running ten rounds through the chrono (these were used AF darts). No spacer was used. Results in order: 210, 211, 215, 223, 212, 209, 211, 210, 224, 219
@@VileMods I am guessing that this is after you put in the kit
@@rextonhart Yep, just swapped the spring out and checked it with the kit in. I originally was seeing 220s with just this spring but the ranges varied down to low 170s and high of 230s. The biggest thing the kit provides is consistency. Not to mention, this spring may not be optimal after my original use and the fact that it's warped so badly now might be affecting it's performance.
@@VileMods ok thanks. I do not has a chronograph so this helped a lot
@@rextonhart No problem!
Hi for your information... There is now a 2nd metal kit for the Nexus Pro. It includes a metal air chamber, a metal priming bar, a metal catch and a metal mag release lever.
AKBlasterMod is offering the set in the colors of silver and red.
But you need to combine this new kit with the kit that is shown in this video the get the complete tuning experience. You can even use a 16 kg spring then.
I just looked at the kit and may be getting it. I'm a bit disappointed that they didn't redesign the telescoping piece and make the blaster short dart only. This could have been an opportunity to give a slight increase of performance by reducing dead space, remove the slop when priming it, and reducing the priming length.
@@VileMods Same opinion here. I already contacted AKBlasterMod to offer a "one piece" pusher... I hate the telescoping pusher. You can unscrew the head of the pusher. Should not be so hard to make a longer pusher body. Time will tell.
Should I get a nexus pro or stryfe (might look into the stryfe killer if I can find one). It's for me and my gf as we're having nerf wars in house now lol
The nexus shoots much hrder so its kinda just preferance
Yeah Nexus hits in the 140s to 150s out of the box so close up shots like that might hurt. If you can get a Dart Zone Spectrum it's in the 90s out of the box and has a lot of support right now especially since you can still buy them off the shelf at Walmart.
@@VileMods I went out and bought 2 nexus pros. Me and my gf are in danger now 🤪. But I also have 2 spectrums on the way. The Nexus is so much fun. Thank you btw for the input.
@@VileMods speaking of spectrum. Has anyone figured a way for it to shoot half darts using the adapter from the nexus?
@@oso999x I'm not sure on that one. Only down side to using half darts on a flywheeler is the fact that they don't get the best performance. Nice if you only want to use one ammo type but it'll get lower FPS since it doesn't have contact with the flywheels for as long.
Is it just me or did the worker kit remove the priming lock
Just double checked mine and it still locks.
@@VileMods I'll go take a look at mine again...Dun rmb messing anything up...
It's tolerance issues...Went and open up everything the dart gate seal is a little tight and didn't go all the way in...
@@no2moloh Yeah it can be a bit snug, a bit of use and lube on the o-ring should help.
I just don’t see how someone could regularly run the nexus with the spring upgrade PLUS the 175FPS spacer
Nice mod i also finished a mod today it will hopefully come out on my channel soon
I'm acturally trying to get my nexus pro down some, hopefully with just a lighter spring. I want to take it to an HvZ and other 130fps games/events.I could prime it and leave it primed for a time, but... I don't want to stress the rest of the catches and shell. Adventure Force blasters are kinda cheap. Thanks walmart. I can feel the 10 dollar difference in the Max line haha.
A properly built brass barrel is still the way to go 😉, 240fps easy.
My club is a 220-230 cap so that's a negative for me.
Use a weaker spring 😉
@@coltstelting6969 Or just don't use the brass? XD
@@VileMods *sounds like someone wants to flex that they can prime strong springs* /s
@@VileMods you can get the brass and because of the improved performance a weaker spring/lighter prime while keeping the desired FPS
Flexus Pro