Check out the original ultrasonic video here 👉 th-cam.com/video/BTN7-C72eHA/w-d-xo.html ✅Click here for an ultrasonic cleaner ➜ amzn.to/32oVRzu For more videos like this, check out: 👉Best Way To Clean a Honda Style Carburetor ➜ th-cam.com/video/uAHdhuDpeKw/w-d-xo.html 👉Easiest Way To Clean A Metal Briggs Carburetor ➜ th-cam.com/video/kJfpTX2Lx0g/w-d-xo.html 👉Easiest Way To Clean a Plastic Briggs Carburetor ➜ th-cam.com/video/eGF_ynkc3C0/w-d-xo.html You can connect with Steve here too: ✅Visit Steve’s WEBSITE ➜ www.stevessmallenginesaloon.com/ ✅Visit Steve’s PARTS & TOOL STORE ➜ www.amazon.com/shop/stevessmallenginesaloon ✅Follow Steve on FACEBOOK ➜ facebook.com/stevessmallenginesaloon ✅Follow Steve on INSTAGRAM ➜ instagram.com/stevessmallenginesaloon/ ✅Follow Steve on TWITTER ➜ twitter.com/SteveSaloon
I loved the gasoline trick from the other video you did, but I have an old piece of silver chainmail and I wonder if it will be a good cleaner for this. Also I don't have an ultrasonic cleaner. I have used the bicarbonate of soda, aluminium foil and boiled water bath, I have also used toothpaste which helped, but I am wanting the brightest silver imaginable. Could you please find out if it's safe to do a cleaning experiment using petrol and silver? Thank you!!
Hi Steve! What would you suggest as a more affordable cleaner for jewellery? I don't want to pay thousands, just the best domestic one will do. It's just for my rings that have intricate designs with lots of nooks and crannies that even Interdental brushes can't get to - but I also don't want to damage the diamond settings or stones etc. Never used one before, so not sure if I need to buy a special solution for them too? Thank you for your advice!
I almost gave up on my old MTD Yard Machines 139cc mower that was running very rough. But I used an ultrasonic cleaner filled with water and with gasoline in a plastic container for 5 minutes on each side of the carburetor. There was a small amount of particles at the bottom of the container that had come from the previously cleaned carburetor! And now the mower is easy to start and runs smoothly and strong! Thanks for the awesome video.
yup if you have not tried the unleaded gasoline trick... you are missing out!! one thing is to dip the carb in berryman carb cleaner first for at least 1/2 an hour .. I did it on honda generator carbs (stripped down). then ran it in the unleaded gasoline for 3 x 15 min sessions turning the carb in the each time session. then dip the carb after a good rinse off in fresh unleaded gasoline. brush off any stuff left, blow dry with air compressor air. final dip in the fresh can of berryman carb cleaner to treat the aluminum for anti corrosion. trust me it works!! it worked on hard to clean Yamaha generator carbs worth 300.00 each!! well done steve!! well done!!
Steve, flammable solvents are OK as long as the main bath is water. However I'd make sure the container of solvent has plenty of air space and/or is vented. As heat increases from the ultrasonic energy, the vapor pressure will increase and a tight container with no air space/vent could rupture. My other tip is that the most effective cleaning occurs about 1" from the bottom of the tank. Try and keep your parts in the center of the tank for the most effective cleaning. (vs. floating them on the surface.) You can add weight/ballast to the jars and rest them in the tank's basket. Great video by the way!!
Just wanted to say thanks... just received my 6L cleaner.. and it nicely fit a 1L ice cream tube. 2 ... 50 round 9mm tray loaded with 223 cases.. stacked.. in 30 mins... 100 rounds cleaned and ready for polish.. Did more in 5 hours than I would in 3 weeks of wet tumbling and the cleaner tank is pristine... Great tip. Again many thanks.
I have been using an Ultra Sonic Cleaner for 5 1/2 years and never knew I could put parts into a different vessel and have them come out clean, thx so much for sharing and keep up the great work, TJ
Re: comments on gasoline? Those are people speaking from "ignorance and fear", I just saw your previous video on Ultrasonic cleaners and I'm here moments after watching that. Thanks for the update!
I commented on your last video just now about the Ziploc bags. I'll leave the comment up for the algorithm, but hahaha that's so cool you covered it in this video!
I have your EXACT same ultrasonic machine- for years I've had 3 gallons of Berryman's "Chem-Dip" carb cleaner in it, after hundreds of carbs and 5+ years it finally went bad on me and started leaving a yellow-looking sticky coating that doesn't easily come off, so I switched to Deionized Water with a Tablespoon of Dawn Dish soap and a Tablespoon of Purple Power concentrate, ran my first Honda pressure washer carb in it this week, and she worked like a champ! THANKS for all the info (Subscribed)
When you want to put any chemical in a plastic container juste look on the bottom and check for the recycling symbol to will see a series of lettre like ( ldpe , hdpe, pp, etc ) that is the type of plastic that you have so just check online if it is compatible with your chemical.
I owned and ran a dive shop for a number of years back in the mid 90's... I only used two cleaners for cleaning corroded and nasty regulators etc, Simple Green and Vinegar. Anything that would not clean with Simple Green, vinegar would. I also used Tupperware Pickle Containers, they have a slide out tray, that made getting parts out easy. I made a platform for it with PVC and a piece of lexan to suspend the container, and it was upright and easy to get parts in and out of.
I think you're absolutely correct about the fire hazard about using gasoline or other flamables (like alcohol as I intend to do) in a CLOSED container, with as little air as possible. And to be on the safe side don't use the heating. It's the vapors that catch fire, so not heating it means a lot less vapors (isolated in clossed container with as little oxygen as practical). Btw make sure the jars you're using with the fuels (or nasty chemicals) don't unscrew their lids under ultrasonic vibrations. I was cleaning some soiled jars yesterday (used it like a dish-washer basically :)), and I saw 3 of the jars open themselves in several seconds after starting it. Zip-lock bags are also very useful, especially for cooking ... :) yes, you can use it as a sous vide for cooking, like tenderizing meat, or beating eggs into fine emulsion. And the best thing of all - again about alcohol - you can age alcohol in your ultrasonic cleaner! :) Take some cheaper alcohol (or whiskey, rum or whatever you like) put in a container that won't unscrew itself, add some wooden chips or small sticks (stripped from the bark! - just the wood), ideally you can buy some that were actually used as a barrel for aging wine or other alcohol so they'll have richer aroma, and run it for about 15 mins. You'll end up with an alcohol that's like been aged several years! Cheers! :)
Hey Steve, great video. Have been using an ultrasonic cleaner at work for a few years now. We use a product called "Alconox" most of the time. It works great on anything metal, glass, plastic, etc... - It's a bit pricey to buy, but the results are really good. We buy it, in what looks like a milk container - holds 4 lbs of the powder. Cost about $60 here in Canada, but you only need to mix it 1:100 ratio (2-1/2 tablespoons per gallon). One container makes about 50 gallons.
Great video THANX. Re petrol in plastic! Not all plastics are the same, so make sure the plastic container being used is Okay with any type of fuel you use in the cleaning please.
Great video Steve. I never knew I could ultra-sonically clean stuff in a jar or zip-lock. What a genius idea to not pollute all of the solution in the tank.
If using a jar or bag (isolation container), you don't need the ultrasonic cleaner's tub to have cleaning solution in it. You fill it with water (distilled is preferred) and put the cleaning solution in the isolation container with the part.
For all my small engine, nuts and bolts, and other items (including gun parts), I use detergent 30W motor oil... Not only cleans real well, it helps to keep parts from rusting after being cleaned. If you need it oil free afterwards, whip it down with a degreaser.. You will not need as much either..
how would your best way to do motocross crankcases, would it be a good idea to brush with gasoline or acetone within a open bag while holding in the ultrasonic cleaner ... because of shape would be hard to put in and seal a ziploc bag and would take lot of gasoline
Steve, these tips are gold ! The gasoline thing is more of a worry for the same people that need instructions on a shampoo bottle. Lather,rinse, repeat. Some people are still in the shower😂
Great video Steve. I’m sure you remember the old pioneer 1074 chainsaws would heat the gas so hot it would boil in the tank. Especially when the nickel was worn off the cylinder walls by the exhaust. Lol I’ve seen lots boil gas But I’ve never seen one catch fire. I’ll be using gasoline to clean my parts too.
Great explanation on the use of gasoline in this manner with an ultrasonic cleaner. Too many people are misinformed, or just don't understand, how an ultrasonic cleaner works. I think just to be that much more safe you could do everything outside just in case the zip baggie broke and you had gasoline fumes appear. Even then a properly functioning machine will have no ignition source. Thumbs up to your reviews!
@@StevesSmallEngineSaloon Consider if the baggie broke, not only is the whole water surface covered with gasoline, the agitation of the water will accelerate vapor production even more. While the risk of explosion in most circumstances is minimal, I'd strongly recommend doing outside for the increased ventilation, or seeing if kerosene (or other light solvent like varsol) works as a close-enough substitute without so much vapor production.
@@fromagefrizzbizz9377 Good point. A lot of people don't realize that it's not the fluid gasoline that's so flammable, it's the vapors, and the reason for carburetors on internal combustion engines. And vapors are invisible and heavier than air, so can flow around like a liquid.
I just found your video's and channel tonight. I was looking for a ultrasonic cleaner for my antique tractor carburetor when I stumbled on your video's I absolutely love them especially the comments I'm still crying with laughter.
I have the same cleaner, love it and love your tips. My only concern with using a glass jar is as it heats up it pressurizes and I'm not clear how far that can go. But I figure it's probably a good idea to prewarm the glass jar and solution in hand (maybe under a hot water faucet) with the lid on loosely. Once it's as warm as the water, then tighten the lid and hit the beach. But I wanted to make a comment about using gasoline to clean/degrease: I agree totally. Best stuff there is for this. But it will leave a residue on the part. This coming from someone who's waxed bicycle chains as a lubricant for decades and swears by it. With one very important caveat: the first time a chain is waxed it must absolutely clean, stripped, bare-metal and gasoline alone won't do it because of that residue left behind. It has to be stripped of everything, and the only thing I know that'll do that is an isopropyl alcohol, or acetone bath after the gasoline treatment. Then the paraffin will adhere and provide a good base and last.
Thank you for your video. So informative. How has the ultrasonic machine held up? Now 4 years later, would you purchase this same brand and model again or is there a different one you'd recommend now? I'm looking to clean my titanium silencer
Hi Steve, I give you some tips: 1) Plastic cups are not used. Better glass or stainless steel. 2) To clean aluminum parts, the best is the aqueous solution with suitable degreaser. Temp: 60 ° C This way, Not damage orings 3) The pieces are not supported without the basket. They are not thrown into the tank either. You can damage the transducers. 4) Solvents are immediately heated with ultrasound. They are dangerous and emit vapors that can affect the user. Greetings from Argentine!! and thanks
After watching your video I bought an Ultrasonic cleaner for doing my Carby. I went by your idea of petrol (I'm a foreigner) in a sure seal bag. After reassembling, the Edger has more power than it ever did. (Maybe it's been such a long time I forgot) Thank you for all your information.
Thanks for the video. I have access to the heads from the distillation process for making alcohol. 95% methanol...it usually gets discarded or used as a disinfectant/cleaner. Any idea if it'd work safely in a jar?
Steve, 2 thoughts For small parts I use a large tea infuser, it's stainless steel screen allows for very small parts to be cleaned then blown off after without the fear of loosing them and it keeps floats below the solution so they get totally cleaned. The other is that gasoline will give off vapors and may build pressure and leak, remember your fuel tanks are vented. Not really dangerous but could contaminate your so.ution. keep up the great videos 🇨🇦
Hopefully some will "Sort by recent" and see this comment. 🤞 All of your tips are great. I would like to add my technique for keeping low VO2 solvents separate from the UltraSonic cleaning tank. I have a small unit and use small stainless steel pans usually filled with a citrus cleaner ,buoyantly balanced to the point that they lightly rest on some 3/4" plastic spacers in the tank, just under the pan. This allows me to quickly switch cleaners, and even melt hot wax for bicycle chain treatment. I will be testing gasoline in closed glass mason jars with plenty of air headroom for especially stubborn crud. Thanks for sharing your experiences with us. 🙏 Peace, Love, Health, and Freedom, to all who are fortunate enough to strive for these goals. 🙏 ct
in the msds sheet for gasoline it listed and chemically classified as a solvent so theres that i use gas to clean greasy motorcycle parts and to clean motorcycle plastics
Steve, great video and advice. I’ve used Dawn in my ultrasonic for years but at work I’ve tried using a small glass container and “gasoline/2 cycle mix” in mine.... it cuts the clean time in half and I believe it dissolves of solidified debris that has dried in carbs from setting. I do run my heat but keep it under 100 degrees and creep the lid loose on my jar because it seemed to build pressure. My jar sits perfectly on my basket so it won’t tip over. The bubble action is amazing to watch. Thanks Steve!!!!!
Hi Steve I have the same ultrasonic cleaner. I have a helpfull tip .You have to be careful of some cleaners when you use the heater not in a container and water bath is the fumes (some non petroleum products) of the cleaning you can get an ill feeling from the fumes. I have experience that not a good feeling. The container ia a great idea and keeps all parts together in one container. Keep up the good work
You’re spot on here Steve. Basically, if they don’t like to do or use something you say/promote, don’t use/follow it then. Seems simple enough to me, huh?
The pure solvent, the one used in painting jobs, is the best natural degreaser that exists, although it attacks rubber gaskets more than gasoline, but it is equal to or better than gasoline in removing grease and a little safer and at the same time. less, cheaper in my country!
Thank You, it would have been helpful to mention the dawn concentration in water that is good to use. Also would it be a good idea to clean jewelry in gasoline and then put it into another jar with dawn solution as a type of rinse?
my understanding is that gasoline is NOT flammable in liquid form, it's the vapor or "gas" form that is volatile and flammable (one of the reasons it needs to be aspirated in an ICE, right?). Also gasoline in a jar is missing one of the three elements you need for combustion, so eloquently described on your great channel, an ignition source or spark. Also, I read that the bubbles that ultrasound create are IMPLOSIVE and not EXPLOSIVE, this is another reason why ultrasonic cleaners are not volatile, like a large building being demo'd it just collapses on itself without blowing up the other buildings around it. Just my 2 cents of understanding. Love the channel, learned a ton from your efforts.
Very helpful. A lot of ppl will use Dawn and vinegar (or citric acid for cooking) for cleaning rifle brass. The brass comes out very clean but the acid needs to be neutralized with something like bicarb soda to stop corrosion. The main point about using even weak acids is to keep the acid away from the stainless steel tank. The tank walls are paper thin because the tank form is deeep drawn and stretched; something like diluted vinegar will chew through and make pinholes, particularly if the solution is contaminated with dissolved metals. (Scientists call this intergranular corrosion from dissimilar metals). Using CLEAN water in the tank will save a lot of grief...if the tank leaks it drips fluid straight to the circuit board. Your method of using a jar is ideal protection and saves tipping out a whoĺe tankful of used chemicals. Thumbs up.
I have a tractor that is stuck. I wonder if I filled cylinder with atf and acetone. Filled a hose and jar with fluid then place jar in ultrasonic cleaner. Will the sonic waves travel into cylinder and break it free?
plastic container of gas vs chainsaw...so no vent on the plastic container lid but there is on the chainsaw...yes? so can't pressure build in the plastic container with no way to vent (like on a gas can) so I worry about the heat/pressure. The jar can float in water but can the gas tank on the chainsaw and no water get in or does it let some air in? (I saw your video on when caps go bad)...I just worry about stuff...so I ask.
Is your ultrasonic cleaner still working? How often and how long are you using it for? Considering buying one from Amazon but lots of negative reviews saying it doesn't last. I will be using it in my shop daily for greasy bicycle parts.
I used gasoline in a glass jar with no heat after watching your other video. Cleaned parts well and no other problems. However, when I opened the lid to the jar there was a sound as if the jar had become under pressure. I will probably try it again before deciding on the future of using gas. Keep the videos coming!
Ultrasonic energy creates implosions of air bubbles and generates heat due to the process. Having Gasoline is not safe and is not recommended. I work with some major manufacturers of ultrasonic baths and would not introduce Gasoline in the bath.
Might be a Canadian only tip but milk bags seem to be a bit sturdier than zip locks for smaller cube carbs. No idea if fuel will melt them over time. I seal them with a chip clip. Clean the milk protein out first by running some fuel in a new bag.
Haven't seen a milk bag since our time in the prairies -- brings back memories! I can't imagine how much milk my parents bought -- drank with every meal and chugged it down like water whenever we ran in from outside...
What would you use to remove old varnish on a carburetor? An how do you get those peanut butter jars to seal? I had to weigh them down with bigger bolts to keep it upright.
I use for chains, coins, everything else I find with the metal detector, a solution of vinegar (30%), ethyl alcohol 70-75 ° (25%) 40% water and 5% gasoline ... it may sound strange, but clean everything from silver, bronze and iron coins, + the chainsaw chain looks like new ... I will test only with gasoline, to compare the results, but this solution was recommended to us by a colleague who is chemist :)
I like your attitude about the gasoline-I don’t see anything unsafe about it, it works for me and if you’re not comfortable with it don’t do it. Great information, thanks.
Using gasoline like this in an ultrasonic cleaner is probably a bit safer than using gasoline for cleaning parts in the open. The problem isn't with the ultrasonic cleaner, it is when you open the jar, remove the part, and dry it off. That's when you generate a cloud of gasoline fumes, and that's when the danger occurs. The degree of hazard depends on the ventilation, and whether there are sources of ignition near floor level where the heavy gasoline fumes settle.The ultrasonic method would be safer than just cleaning with gasoline in the open because the latter is likely to generate more fumes.
@@kevinmartin7760 The ultrasonic method would generate a lot more fumes, being evenly spread across the entire surface, and the ultrasonic agitation would be literally shaking it into the air.
Fifty years ago I worked at a auto repair garage and the owner there swore by kerosene to clean parts.He always said it was a better cleaner then gas for cleaning parts.. I would also recommend Dollar Stores LA's Totally Awsome concentrated degreaser, $1.00 for a qt.bottle.Great stuff and a chart on the back with dilution mix ratios for what you are cleaning.
What about using a soda blaster like people use on motorcycle and car carburetors? Usually they use that in conjunction with an ultrasonic parts cleaner vs a ultrasonic alone and it’s safe to put any part in a soda blaster including plastics.
I use gasoline to clean tools all the time it works great i don't have a sonic cleaner yet i bought one its comming my only question is could the gasoline melt the plastic jar like it dose a red solo cup ?
Been thinking of using antifreeze as the medium, as my cleaner is in a cold environment. Do you use auto antifreeze, or RV antifreeze? And what concentration?
Great tips! thank you, to you and the subscribers. Thankfully here in the UK we don't have access to that highly volatile Gasoline, so we just use low or high octane Petrol.... 👍😂🤣😂🤣
I put the parts in the basket without any jars or containers. I also lined my basket with finer screen to prevent small parts from falling threw. Simple Green or Evap-O-Rust.
@@AuMechanic I follow you, but I don't mind cleaning the tank every so often. I use the Simple Green or Evap-O Rust over and over for several cycles. I'm not trying to tell anyone how to use their cleaner just a suggestion.
Hey Steve, this makes the second video I've watched on your channel. I'm subscribed now! Super great content and love the common sense approach. Thank you for your time and effort.
A 50/50 mix of white vinegar and water is a terrific ultrasonic cleaning solution for tarnished brass (I'm a reloaded). But as you said in your first video, it's a caustic, so use with caution on materials that might etch or discolor. I also use ẞimple Green in about 75% water. Use "Simple Green D" on aluminum parts, as it will not etch or discolor aluminum.
Acids and bases are common corrosive materials. Vinegar is not considered "caustic", as it is acidic - anything that has a pH level above 7 means the substance is alkaline. As a substance lowers in pH levels from a neutral 7 to anything below, it indicates an increase in acidity. A substance becomes increasingly more acidic as their pH levels decrease. The term “caustic” properly refers only to strong bases, particularly alkalis, and not to acids, oxidizers, or other non-alkaline corrosives.
Don't have any tips or tricks for ya Steve but I've been thinking of getting one of these for quite some time I really appreciate your help with these things! 👍
Haven't tried it yet but if gas works good then camp fuel works better. I use it regularly to pull oil out of porous materials, I used to use gas but camp fuel works in half the time. It does strip paint
does the action of the ultrasonic cause off gassing of the gasoline? does it have potential to create pressure? perhaps using gasoline in a vented container may be safer?
I have the same unit. The container does not need to be closed if the water in the unit is not so deep as to overflow into the container. I use glass baking dishes, & etc.. You will not be restricted by the neck on the jar in this way. I do not use gasoline, instead I use standard solvent which is used for parts cleaning. It leaves no film like gasoline and is almost impossible to ignite.
So you just use parts washer solvent? Wondered why that or the simple green wouldn't work in one of those ultrasonic cleaners....I don't have one, wish I did sometimes though but don't need one often enough to warrant the price. So I just clean everything by hand and soak in simple green if I need to overnight.
William Sevier I use what is/ was called “standard solvent”. It is not water based like most of the parts washing solvents today. Basically any fluid will work to a certain extent. It is the microscopic bubbles created by the ultrasonic waves that do the cleaning. A good analogy regarding the liquid used is found in clothes washing. You could wash your clothes in plain water and they would be cleaner than when you put them in the washer, but you use a detergent to help break down the soils and remove more dirt. You can follow this idea by thinking of the ultra sonic cleaner as the washing machine with agitation(parts don’t actually move like the clothes but the fluid does) vs. just soaking the clothes in a pail of water. The difference between your technique (which I used for many years I might add) and ultrasonic cleaning really shows itself with high gloss items such as jewelry. The rings and stones come out virtually like the day they were purchased. I mention this only to tell you that there is a difference between soaking and ultrasonic cleaning. Harbor Freight has a small ultrasonic cleaner that I upgraded from primarily because of capacity. (It will hold small carburetors, gun action parts, milling machine collets, and etc.). It worked fine but a guy who already had one told me what I needed to do to it before using it to prevent damage.( Like most Harbor Freight items they need a little tweaking). If you decide to go this route contact me here and I will tell you what to do. It’s not much but needs to be done to prevent it from being damaged.
@@slicktmi If your unit from Harbor Freight is the one with the silver plastic housing, somewhat oval shaped, you need to more or less caulk the seam just inside the rim that goes all the way around the tank with a silicone caulk. I used RTV Red due to the fact that it is high temp and the unit does have a heater. It probably could be done with any silicone caulk because I doubt the temp ever gets that high that RTV Red is actually necessary. If you do not do this the fluid in the tank will eventually destroy the electronic control of the unit as it, or atomized fluid, will pass through this seam. Make sure you use a 100% silicone so that it remains flexible over time and just force it into the seam with your fingertip. Wipe the excess off the wall with a rag saturated with mineral spirits for a neat looking job. RTV Red is sold in most auto parts stores or home centers in a tube on a blister card. Hope this helps.
Hi SteveO, I have noticed that the Vevor comes with with 3or more color labels on them on certain models, any ideas??? Colors like dark blue,light blue & black. So what with the different colors of the vector brand of ultrasonic cleaners.
Check out the original ultrasonic video here 👉 th-cam.com/video/BTN7-C72eHA/w-d-xo.html
✅Click here for an ultrasonic cleaner ➜ amzn.to/32oVRzu
For more videos like this, check out:
👉Best Way To Clean a Honda Style Carburetor ➜ th-cam.com/video/uAHdhuDpeKw/w-d-xo.html
👉Easiest Way To Clean A Metal Briggs Carburetor ➜ th-cam.com/video/kJfpTX2Lx0g/w-d-xo.html
👉Easiest Way To Clean a Plastic Briggs Carburetor ➜ th-cam.com/video/eGF_ynkc3C0/w-d-xo.html
You can connect with Steve here too:
✅Visit Steve’s WEBSITE ➜ www.stevessmallenginesaloon.com/
✅Visit Steve’s PARTS & TOOL STORE ➜ www.amazon.com/shop/stevessmallenginesaloon
✅Follow Steve on FACEBOOK ➜ facebook.com/stevessmallenginesaloon
✅Follow Steve on INSTAGRAM ➜ instagram.com/stevessmallenginesaloon/
✅Follow Steve on TWITTER ➜ twitter.com/SteveSaloon
How many Liter is the ultra :) Thansk from Denmark
I clicked the link for the cleaner, it’s a dud. Where can I find a workable link?
My thoughts on gas being a no no was the cavitations cleaning your item may become the source of ignition?
I loved the gasoline trick from the other video you did, but I have an old piece of silver chainmail and I wonder if it will be a good cleaner for this. Also I don't have an ultrasonic cleaner. I have used the bicarbonate of soda, aluminium foil and boiled water bath, I have also used toothpaste which helped, but I am wanting the brightest silver imaginable. Could you please find out if it's safe to do a cleaning experiment using petrol and silver? Thank you!!
Hi Steve! What would you suggest as a more affordable cleaner for jewellery? I don't want to pay thousands, just the best domestic one will do. It's just for my rings that have intricate designs with lots of nooks and crannies that even Interdental brushes can't get to - but I also don't want to damage the diamond settings or stones etc. Never used one before, so not sure if I need to buy a special solution for them too?
Thank you for your advice!
Wife's dentures came out super clean but she's pissed about the taste of gasoline. LOL
Use diesel next time.
ROFL.
Try nitro methane, give her a boost🤣
and she chewed me out for it with ethanol on her breath.
Hahah
I almost gave up on my old MTD Yard Machines 139cc mower that was running very rough. But I used an ultrasonic cleaner filled with water and with gasoline in a plastic container for 5 minutes on each side of the carburetor. There was a small amount of particles at the bottom of the container that had come from the previously cleaned carburetor! And now the mower is easy to start and runs smoothly and strong! Thanks for the awesome video.
Nice work!
yup if you have not tried the unleaded gasoline trick... you are missing out!!
one thing is to dip the carb in berryman carb cleaner first for at least 1/2 an hour ..
I did it on honda generator carbs (stripped down). then ran it in the unleaded gasoline for 3 x 15 min sessions
turning the carb in the each time session.
then dip the carb after a good rinse off in fresh unleaded gasoline. brush off any stuff left, blow dry with air compressor air.
final dip in the fresh can of berryman carb cleaner to treat the aluminum for anti corrosion.
trust me it works!!
it worked on hard to clean Yamaha generator carbs worth 300.00 each!!
well done steve!! well done!!
I filled the sonic cleaner with cleaning solvent. Cranked the heat and dropped in varnished carb pieces. Worked amazing
The traffic is your fault, you earned it, just keep it up.
Thank You...
Steve, flammable solvents are OK as long as the main bath is water. However I'd make sure the container of solvent has plenty of air space and/or is vented. As heat increases from the ultrasonic energy, the vapor pressure will increase and a tight container with no air space/vent could rupture. My other tip is that the most effective cleaning occurs about 1" from the bottom of the tank. Try and keep your parts in the center of the tank for the most effective cleaning. (vs. floating them on the surface.) You can add weight/ballast to the jars and rest them in the tank's basket. Great video by the way!!
How would you vent a secondary container? It would leak into the main bath
Just wanted to say thanks... just received my 6L cleaner.. and it nicely fit a 1L ice cream tube.
2 ... 50 round 9mm tray loaded with 223 cases.. stacked.. in 30 mins... 100 rounds cleaned and ready for polish..
Did more in 5 hours than I would in 3 weeks of wet tumbling and the cleaner tank is pristine...
Great tip.
Again many thanks.
You're Welcome...
I have been using an Ultra Sonic Cleaner for 5 1/2 years and never knew I could put parts into a different vessel and have them come out clean, thx so much for sharing and keep up the great work, TJ
You're Welcome...and Thank You...
Most enjoyable small gas engine channel I have found.
Thank You...
Re: comments on gasoline? Those are people speaking from "ignorance and fear",
I just saw your previous video on Ultrasonic cleaners and I'm here moments after watching that.
Thanks for the update!
Well said!
I commented on your last video just now about the Ziploc bags. I'll leave the comment up for the algorithm, but hahaha that's so cool you covered it in this video!
Right on buddy!
I have your EXACT same ultrasonic machine- for years I've had 3 gallons of Berryman's "Chem-Dip" carb cleaner in it, after hundreds of carbs and 5+ years it finally went bad on me and started leaving a yellow-looking sticky coating that doesn't easily come off, so I switched to Deionized Water with a Tablespoon of Dawn Dish soap and a Tablespoon of Purple Power concentrate, ran my first Honda pressure washer carb in it this week, and she worked like a champ! THANKS for all the info (Subscribed)
When you want to put any chemical in a plastic container juste look on the bottom and check for the recycling symbol to will see a series of lettre like ( ldpe , hdpe, pp, etc ) that is the type of plastic that you have so just check online if it is compatible with your chemical.
I owned and ran a dive shop for a number of years back in the mid 90's... I only used two cleaners for cleaning corroded and nasty regulators etc, Simple Green and Vinegar. Anything that would not clean with Simple Green, vinegar would. I also used Tupperware Pickle Containers, they have a slide out tray, that made getting parts out easy. I made a platform for it with PVC and a piece of lexan to suspend the container, and it was upright and easy to get parts in and out of.
Here’s a related tip.
Hit up used appliance shops for silverware baskets. Lot of different designs available, great for separating parts.
I think you're absolutely correct about the fire hazard about using gasoline or other flamables (like alcohol as I intend to do) in a CLOSED container, with as little air as possible.
And to be on the safe side don't use the heating.
It's the vapors that catch fire, so not heating it means a lot less vapors (isolated in clossed container with as little oxygen as practical).
Btw make sure the jars you're using with the fuels (or nasty chemicals) don't unscrew their lids under ultrasonic vibrations.
I was cleaning some soiled jars yesterday (used it like a dish-washer basically :)), and I saw 3 of the jars open themselves in several seconds after starting it.
Zip-lock bags are also very useful, especially for cooking ... :) yes, you can use it as a sous vide for cooking, like tenderizing meat, or beating eggs into fine emulsion.
And the best thing of all - again about alcohol -
you can age alcohol in your ultrasonic cleaner! :)
Take some cheaper alcohol (or whiskey, rum or whatever you like) put in a container that won't unscrew itself, add some wooden chips or small sticks (stripped from the bark! - just the wood), ideally you can buy some that were actually used as a barrel for aging wine or other alcohol so they'll have richer aroma, and run it for about 15 mins.
You'll end up with an alcohol that's like been aged several years!
Cheers! :)
Crazy talk
Hey Steve, great video. Have been using an ultrasonic cleaner at work for a few years now. We use a product called "Alconox" most of the time. It works great on anything metal, glass, plastic, etc... - It's a bit pricey to buy, but the results are really good. We buy it, in what looks like a milk container - holds 4 lbs of the powder. Cost about $60 here in Canada, but you only need to mix it 1:100 ratio (2-1/2 tablespoons per gallon). One container makes about 50 gallons.
Steve, tell the lightning guy if he sees "lightning" in HIS ultrasonic cleaner, it's time to get a new one!
Yep. Or run like a striped ape !
Great video THANX.
Re petrol in plastic!
Not all plastics are the same, so make sure the plastic container
being used is Okay with any type of fuel you use in the cleaning please.
Great video Steve.
I never knew I could ultra-sonically clean stuff in a jar or zip-lock. What a genius idea to not pollute all of the solution in the tank.
Thank You...
If using a jar or bag (isolation container), you don't need the ultrasonic cleaner's tub to have cleaning solution in it. You fill it with water (distilled is preferred) and put the cleaning solution in the isolation container with the part.
For all my small engine, nuts and bolts, and other items (including gun parts), I use detergent 30W motor oil... Not only cleans real well, it helps to keep parts from rusting after being cleaned. If you need it oil free afterwards, whip it down with a degreaser.. You will not need as much either..
watched both videos, amazing information! no BS, no filler. the people fear mongering about the gasoline is funny too.
You're Right! It's hilarious!
I've always used diesel for cleaning oily parts
how to best dispose of the used up dirty gasoline? for that matter, what is the proper way to dispose of any cleaning agent you used?
how would your best way to do motocross crankcases, would it be a good idea to brush with gasoline or acetone within a open bag while holding in the ultrasonic cleaner ... because of shape would be hard to put in and seal a ziploc bag and would take lot of gasoline
Would this be good for cleaning chain saw chain's? or would it be to messy?
Steve, these tips are gold ! The gasoline thing is more of a worry for the same people that need instructions on a shampoo bottle. Lather,rinse, repeat. Some people are still in the shower😂
Right on
Great video Steve. I’m sure you remember the old pioneer 1074 chainsaws would heat the gas so hot it would boil in the tank. Especially when the nickel was worn off the cylinder walls by the exhaust. Lol I’ve seen lots boil gas But I’ve never seen one catch fire. I’ll be using gasoline to clean my parts too.
Great explanation on the use of gasoline in this manner with an ultrasonic cleaner. Too many people are misinformed, or just don't understand, how an ultrasonic cleaner works. I think just to be that much more safe you could do everything outside just in case the zip baggie broke and you had gasoline fumes appear. Even then a properly functioning machine will have no ignition source. Thumbs up to your reviews!
Thank you!
@@StevesSmallEngineSaloon Consider if the baggie broke, not only is the whole water surface covered with gasoline, the agitation of the water will accelerate vapor production even more. While the risk of explosion in most circumstances is minimal, I'd strongly recommend doing outside for the increased ventilation, or seeing if kerosene (or other light solvent like varsol) works as a close-enough substitute without so much vapor production.
Use diesel
@@fromagefrizzbizz9377 Good point. A lot of people don't realize that it's not the fluid gasoline that's so flammable, it's the vapors, and the reason for carburetors on internal combustion engines. And vapors are invisible and heavier than air, so can flow around like a liquid.
I just found your video's and channel tonight. I was looking for a ultrasonic cleaner for my antique tractor carburetor when I stumbled on your video's I absolutely love them especially the comments I'm still crying with laughter.
Awesome! Thank you!
I have the same cleaner, love it and love your tips. My only concern with using a glass jar is as it heats up it pressurizes and I'm not clear how far that can go. But I figure it's probably a good idea to prewarm the glass jar and solution in hand (maybe under a hot water faucet) with the lid on loosely. Once it's as warm as the water, then tighten the lid and hit the beach.
But I wanted to make a comment about using gasoline to clean/degrease: I agree totally. Best stuff there is for this. But it will leave a residue on the part. This coming from someone who's waxed bicycle chains as a lubricant for decades and swears by it.
With one very important caveat: the first time a chain is waxed it must absolutely clean, stripped, bare-metal and gasoline alone won't do it because of that residue left behind. It has to be stripped of everything, and the only thing I know that'll do that is an isopropyl alcohol, or acetone bath after the gasoline treatment. Then the paraffin will adhere and provide a good base and last.
Thank you for your video. So informative. How has the ultrasonic machine held up? Now 4 years later, would you purchase this same brand and model again or is there a different one you'd recommend now? I'm looking to clean my titanium silencer
Hi Steve, I give you some tips:
1) Plastic cups are not used. Better glass or stainless steel.
2) To clean aluminum parts, the best is the aqueous solution with suitable degreaser.
Temp: 60 ° C This way, Not damage orings
3) The pieces are not supported without the basket. They are not thrown into the tank either. You can damage the transducers.
4) Solvents are immediately heated with ultrasound. They are dangerous and emit vapors that can affect the user.
Greetings from Argentine!! and thanks
After watching your video I bought an Ultrasonic cleaner for doing my Carby.
I went by your idea of petrol (I'm a foreigner) in a sure seal bag.
After reassembling, the Edger has more power than it ever did. (Maybe it's been such a long time I forgot)
Thank you for all your information.
Fantastic!
Thanks for the video. I have access to the heads from the distillation process for making alcohol. 95% methanol...it usually gets discarded or used as a disinfectant/cleaner. Any idea if it'd work safely in a jar?
Steve, 2 thoughts
For small parts I use a large tea infuser, it's stainless steel screen allows for very small parts to be cleaned then blown off after without the fear of loosing them and it keeps floats below the solution so they get totally cleaned.
The other is that gasoline will give off vapors and may build pressure and leak, remember your fuel tanks are vented. Not really dangerous but could contaminate your so.ution. keep up the great videos 🇨🇦
Good idea, especially for really small carb parts. 👍
Doesn't ziploc get melted in high temp ?
What temperature do you set your ultra sonic at when you use gas
Thanx Steve! Always used diesel or kerosene without a ultrasonic cleaner,what do think?
Hopefully some will "Sort by recent" and see this comment. 🤞
All of your tips are great. I would like to add my technique for keeping low VO2 solvents separate from the UltraSonic cleaning tank.
I have a small unit and use small stainless steel pans usually filled with a citrus cleaner ,buoyantly balanced to the point that they lightly rest on some 3/4" plastic spacers in the tank, just under the pan.
This allows me to quickly switch cleaners, and even melt hot wax for bicycle chain treatment. I will be testing gasoline in closed glass mason jars with plenty of air headroom for especially stubborn crud.
Thanks for sharing your experiences with us. 🙏
Peace, Love, Health, and Freedom, to all who are fortunate enough to strive for these goals. 🙏
ct
in the msds sheet for gasoline it listed and chemically classified as a solvent
so theres that
i use gas to clean greasy motorcycle parts and to clean motorcycle plastics
Steve, great video and advice. I’ve used Dawn in my ultrasonic for years but at work I’ve tried using a small glass container and “gasoline/2 cycle mix” in mine.... it cuts the clean time in half and I believe it dissolves of solidified debris that has dried in carbs from setting. I do run my heat but keep it under 100 degrees and creep the lid loose on my jar because it seemed to build pressure. My jar sits perfectly on my basket so it won’t tip over. The bubble action is amazing to watch.
Thanks Steve!!!!!
You're Welcome...
Hi Steve I have the same ultrasonic cleaner. I have a helpfull tip .You have to be careful of some cleaners when you use the heater not in a container and water bath is the fumes (some non petroleum products) of the cleaning you can get an ill feeling from the fumes. I have experience that not a good feeling. The container ia a great idea and keeps all parts together in one container. Keep up the good work
Have you tried diesel for cleaning?
You’re spot on here Steve. Basically, if they don’t like to do or use something you say/promote, don’t use/follow it then. Seems simple enough to me, huh?
The pure solvent, the one used in painting jobs, is the best natural degreaser that exists, although it attacks rubber gaskets more than gasoline, but it is equal to or better than gasoline in removing grease and a little safer and at the same time. less, cheaper in my country!
Parts washer solvent work great as well> Awesome tip, you are the man!
Thanks 👍
My issue is disposing of all that dirty gasoline afterward. Seems like a pain if you want to be responsible about it? Awesome videos!
Thank You, it would have been helpful to mention the dawn concentration in water that is good to use. Also would it be a good idea to clean jewelry in gasoline and then put it into another jar with dawn solution as a type of rinse?
my understanding is that gasoline is NOT flammable in liquid form, it's the vapor or "gas" form that is volatile and flammable (one of the reasons it needs to be aspirated in an ICE, right?). Also gasoline in a jar is missing one of the three elements you need for combustion, so eloquently described on your great channel, an ignition source or spark. Also, I read that the bubbles that ultrasound create are IMPLOSIVE and not EXPLOSIVE, this is another reason why ultrasonic cleaners are not volatile, like a large building being demo'd it just collapses on itself without blowing up the other buildings around it. Just my 2 cents of understanding. Love the channel, learned a ton from your efforts.
Very helpful. A lot of ppl will use Dawn and vinegar (or citric acid for cooking) for cleaning rifle brass. The brass comes out very clean but the acid needs to be neutralized with something like bicarb soda to stop corrosion. The main point about using even weak acids is to keep the acid away from the stainless steel tank. The tank walls are paper thin because the tank form is deeep drawn and stretched; something like diluted vinegar will chew through and make pinholes, particularly if the solution is contaminated with dissolved metals. (Scientists call this intergranular corrosion from dissimilar metals). Using CLEAN water in the tank will save a lot of grief...if the tank leaks it drips fluid straight to the circuit board. Your method of using a jar is ideal protection and saves tipping out a whoĺe tankful of used chemicals. Thumbs up.
Right on Ray! Thank You...
What do you thinkmof E85 as a Cleaner? In my area we can get 85% grain alcohol as a fuel. It's called E85 locally. Cheaper than gas even.
What do you think about kerosene or white vinegar?
I love your tech tips!
I just bought the same exact sonic cleaner and thank you for the info. gas does work even better than carb cleaner. Keep up the good work.
Thanks, will do!
Just wondering is there a difference between straight gas and ethanol on the cleaning?
I have a tractor that is stuck. I wonder if I filled cylinder with atf and acetone. Filled a hose and jar with fluid then place jar in ultrasonic cleaner. Will the sonic waves travel into cylinder and break it free?
plastic container of gas vs chainsaw...so no vent on the plastic container lid but there is on the chainsaw...yes? so can't pressure build in the plastic container with no way to vent (like on a gas can) so I worry about the heat/pressure. The jar can float in water but can the gas tank on the chainsaw and no water get in or does it let some air in? (I saw your video on when caps go bad)...I just worry about stuff...so I ask.
Your web site seems to be the best place for proposing a video topic.
Just curious what do you do with the dirty gasoline?
Works great in your chainsaw😂
Is your ultrasonic cleaner still working? How often and how long are you using it for? Considering buying one from Amazon but lots of negative reviews saying it doesn't last. I will be using it in my shop daily for greasy bicycle parts.
I used gasoline in a glass jar with no heat after watching your other video. Cleaned parts well and no other problems. However, when I opened the lid to the jar there was a sound as if the jar had become under pressure. I will probably try it again before deciding on the future of using gas. Keep the videos coming!
The temperature in the room can promote evaporation thus liberating vapor that results in pressurization of the container.
Also temp change. If it went in the solution at 40 degrees and the solution is even ten degrees warmer. It will pressurize the container a touch.
lucky lager for life!!! west coast loggin mechanic turned spoiled oilfield mechanic. love your videos man
Thank You...
I’m gonna skip gasoline AND my ultrasonic cleaner and clean all my parts with lightning from now on.
just make sure to wear your welding helmet. safety first!
Corona surface treatment is exactly that, does work well for both metals and some plastics.
Hers your sign....................lol
"YO ZEUS! NEED A FAVOR!"
Ultrasonic energy creates implosions of air bubbles and generates heat due to the process. Having Gasoline is not safe and is not recommended.
I work with some major manufacturers of ultrasonic baths and would not introduce Gasoline in the bath.
Might be a Canadian only tip but milk bags seem to be a bit sturdier than zip locks for smaller cube carbs. No idea if fuel will melt them over time. I seal them with a chip clip. Clean the milk protein out first by running some fuel in a new bag.
Haven't seen a milk bag since our time in the prairies -- brings back memories! I can't imagine how much milk my parents bought -- drank with every meal and chugged it down like water whenever we ran in from outside...
What would you use to remove old varnish on a carburetor? An how do you get those peanut butter jars to seal? I had to weigh them down with bigger bolts to keep it upright.
Love the tips on these. I just picked up a smaller version from a friend and searching for tips was glad to find a familiar face with some ideas.
Thank You...
I use for chains, coins, everything else I find with the metal detector, a solution of vinegar (30%), ethyl alcohol 70-75 ° (25%) 40% water and 5% gasoline ... it may sound strange, but clean everything from silver, bronze and iron coins, + the chainsaw chain looks like new ... I will test only with gasoline, to compare the results, but this solution was recommended to us by a colleague who is chemist :)
did you compare? video?
I like your attitude about the gasoline-I don’t see anything unsafe about it, it works for me and if you’re not comfortable with it don’t do it. Great information, thanks.
Right on Cory...
Using gasoline like this in an ultrasonic cleaner is probably a bit safer than using gasoline for cleaning parts in the open. The problem isn't with the ultrasonic cleaner, it is when you open the jar, remove the part, and dry it off. That's when you generate a cloud of gasoline fumes, and that's when the danger occurs. The degree of hazard depends on the ventilation, and whether there are sources of ignition near floor level where the heavy gasoline fumes settle.The ultrasonic method would be safer than just cleaning with gasoline in the open because the latter is likely to generate more fumes.
The real problem with gasoline is the STENCH!!! Plus the health hazards of the additives. Try alcohol (but not beer.)
@@kevinmartin7760 The ultrasonic method would generate a lot more fumes, being evenly spread across the entire surface, and the ultrasonic agitation would be literally shaking it into the air.
So what about plastic parts like as tanks in these ultrasonic cleaners like weedeater gas tanks
Hi Steve, Can you recommend a "non caustic" cleaner to use to clean resin off my paraphernalia? Thank you! Lilp
Fifty years ago I worked at a auto repair garage and the owner there swore by kerosene to clean parts.He always said it was a better cleaner then gas for cleaning parts.. I would also recommend Dollar Stores LA's Totally Awsome concentrated degreaser, $1.00 for a qt.bottle.Great stuff and a chart on the back with dilution mix ratios for what you are cleaning.
hi do you put the heat on and let it warm up before turning it on to clean parts regards steve
What about using a soda blaster like people use on motorcycle and car carburetors? Usually they use that in conjunction with an ultrasonic parts cleaner vs a ultrasonic alone and it’s safe to put any part in a soda blaster including plastics.
I use gasoline to clean tools all the time it works great i don't have a sonic cleaner yet i bought one its comming my only question is could the gasoline melt the plastic jar like it dose a red solo cup ?
Steve, Loved your updated video!!! What size ultrasonic machine are you using?
I used mason jars for parts and cleaner. I keep antifreeze in as the medium for ultrasonic transfer. Works great.
Been thinking of using antifreeze as the medium, as my cleaner is in a cold environment. Do you use auto antifreeze, or RV antifreeze? And what concentration?
Great tips! thank you, to you and the subscribers.
Thankfully here in the UK we don't have access to that highly volatile Gasoline, so we just use low or high octane Petrol.... 👍😂🤣😂🤣
I put the parts in the basket without any jars or containers. I also lined my basket with finer screen to prevent small parts from falling threw. Simple Green or Evap-O-Rust.
Watch his previous video on this, the point of putting things in a container with solvent and water in the cleaner tank has a purpose.
@@AuMechanic I follow you, but I don't mind cleaning the tank every so often. I use the Simple Green or Evap-O Rust over and over for several cycles. I'm not trying to tell anyone how to use their cleaner just a suggestion.
Steve , good old paint thinner does great!
I've never tried gasoline bur acetone, goof off, kroil, mineral spirits and Colman fuel work pretty good.
Is there a reason you got the 15L one instead of 22L or 30L?
Hey Steve, this makes the second video I've watched on your channel. I'm subscribed now! Super great content and love the common sense approach. Thank you for your time and effort.
Thank You...and You're Welcome...
A 50/50 mix of white vinegar and water is a terrific ultrasonic cleaning solution for tarnished brass (I'm a reloaded). But as you said in your first video, it's a caustic, so use with caution on materials that might etch or discolor. I also use ẞimple Green in about 75% water. Use "Simple Green D" on aluminum parts, as it will not etch or discolor aluminum.
Acids and bases are common corrosive materials. Vinegar is not considered "caustic", as it is acidic - anything that has a pH level above 7 means the substance is alkaline. As a substance lowers in pH levels from a neutral 7 to anything below, it indicates an increase in acidity. A substance becomes increasingly more acidic as their pH levels decrease. The term “caustic” properly refers only to strong bases, particularly alkalis, and not to acids, oxidizers, or other non-alkaline corrosives.
Steve what’s the best cleaner for carburetor for weed eaters chainsaw lawnmower…is it still gasoline??
How long do you leave a cleaner on for cleaning carb parts jets etc
Don't have any tips or tricks for ya Steve but I've been thinking of getting one of these for quite some time I really appreciate your help with these things! 👍
Thank You...
Haven't tried it yet but if gas works good then camp fuel works better. I use it regularly to pull oil out of porous materials, I used to use gas but camp fuel works in half the time. It does strip paint
does the action of the ultrasonic cause off gassing of the gasoline? does it have potential to create pressure? perhaps using gasoline in a vented container may be safer?
How are you disposing of the dirty gas?
havn't tried it yet but will try clr on my next super oxidised carb.
What is your recommendation to remove paint off brass?
Have you tried kerosene as cleaning agent? Its perfect for parts with o-rings etc
If you look at harbor freight manual with the specs it say 120 watt sonic power and 270 watt for the heater so that add them together 400 total
I have the same unit. The container does not need to be closed if the water in the unit is not so deep as to overflow into the container. I use glass baking dishes, & etc.. You will not be restricted by the neck on the jar in this way. I do not use gasoline, instead I use standard solvent which is used for parts cleaning. It leaves no film like gasoline and is almost impossible to ignite.
So you just use parts washer solvent? Wondered why that or the simple green wouldn't work in one of those ultrasonic cleaners....I don't have one, wish I did sometimes though but don't need one often enough to warrant the price. So I just clean everything by hand and soak in simple green if I need to overnight.
William Sevier I use what is/ was called “standard solvent”. It is not water based like most of the parts washing solvents today. Basically any fluid will work to a certain extent. It is the microscopic bubbles created by the ultrasonic waves that do the cleaning. A good analogy regarding the liquid used is found in clothes washing. You could wash your clothes in plain water and they would be cleaner than when you put them in the washer, but you use a detergent to help break down the soils and remove more dirt. You can follow this idea by thinking of the ultra sonic cleaner as the washing machine with agitation(parts don’t actually move like the clothes but the fluid does) vs. just soaking the clothes in a pail of water.
The difference between your technique (which I used for many years I might add) and ultrasonic cleaning really shows itself with high gloss items such as jewelry. The rings and stones come out virtually like the day they were purchased. I mention this only to tell you that there is a difference between soaking and ultrasonic cleaning.
Harbor Freight has a small ultrasonic cleaner that I upgraded from primarily because of capacity. (It will hold small carburetors, gun action parts, milling machine collets, and etc.). It worked fine but a guy who already had one told me what I needed to do to it before using it to prevent damage.( Like most Harbor Freight items they need a little tweaking). If you decide to go this route contact me here and I will tell you what to do. It’s not much but needs to be done to prevent it from being damaged.
@@37yearsofanythingisenough39what needs to be done just bought one
@@slicktmi If your unit from Harbor Freight is the one with the silver plastic housing, somewhat oval shaped, you need to more or less caulk the seam just inside the rim that goes all the way around the tank with a silicone caulk. I used RTV Red due to the fact that it is high temp and the unit does have a heater. It probably could be done with any silicone caulk because I doubt the temp ever gets that high that RTV Red is actually necessary. If you do not do this the fluid in the tank will eventually destroy the electronic control of the unit as it, or atomized fluid, will pass through this seam. Make sure you use a 100% silicone so that it remains flexible over time and just force it into the seam with your fingertip. Wipe the excess off the wall with a rag saturated with mineral spirits for a neat looking job. RTV Red is sold in most auto parts stores or home centers in a tube on a blister card. Hope this helps.
Give MEK a try. I don't have an ultrasonic, but I use it as a degreaser/cleaner in place of brake clean (no acetone).
Hi SteveO, I have noticed that the Vevor comes with with 3or more color labels on them on certain models, any ideas??? Colors like dark blue,light blue & black. So what with the different colors of the vector brand of ultrasonic cleaners.
Thanks Steve, just bought an ultrasonic cleaner and you were the first person I thought of to get advice. Great channel !
Glad to help
Hello great videos, have a question do you use regular tap water or distilled water thanks?
Steve Thank you for all you do.I use simple green mixed with the proper amount of water in mine and have very good results
That's a great idea.
What ratio do you use. Do you use “ purple “ simple green?
how do you get the actual temp of the water to go up?