That’s my rifle and I can’t believe it’s been 5 years! Not long after I got it back I shelved the hobby altogether because I was moving and had a lot going on. I just pulled everything back out a week ago and it took me a minute to remember where I had sent this and what was done to it. I stumbled across this video in the process and it started coming back to me. I never really got a chance to appreciate it until now. I think Troy Hammer was the man behind the tuning? I just want to say that you did an excellent job and my Kral shoots amazing. It’s very consistent and efficient to say the least. Not to mention it hits like a tank! Thanks IA and Troy H. for the quality work!
I really enjoy all video from troy.how to purchase anti bounce hammer spring because i have puncher breaker .25 and already install lane regulator set at 130bar.how big transfer port should i drill to get 50ftpound .thank you
If your'e looking for 50fpe I wouldn't use a regulator. You'll probably need to up the reg to 150bar and replace the power adjuster with a 1" long 5/16-18tpi capscrew and drill all ports to 7/32" plus an internal spring 2" long that fits inside the main spring.
Gerald Williams the marauder has a 212cc tube vs 280cc on the breaker so the shot count would be lower.
6 ปีที่แล้ว
Hi When i shoot mine .22 silent in full power around 855 fps its start to spread the shoots badly, in low and medium settings it shoots like a champ. I have tried jsb jumbo and heavy 5.50 and 5.52 and nothing helps. Do you got some ideas? Thanks
6 ปีที่แล้ว
Hey is there a solution for jamming magazines on the breaker .22? I shoot mostly jsb jumbo 5.50mm and both magazines jams. Thanks
Johan Safstrom the gun must remain level or pointed down during cycling. If pointed up you run the risk of jamming. I have seen the face plate being modified with good results as well. You fill in pellet loading slot so only the hole remains where the probe enters when loaded but you have to load the first pellet skirt first from the rear like the FX mags.
6 ปีที่แล้ว
@@AnnihilatorAirguns Thanks for the reply I Will give it a try to fill the hole. And you doing a great work with your Channel Thumbs up!
That’s my rifle and I can’t believe it’s been 5 years! Not long after I got it back I shelved the hobby altogether because I was moving and had a lot going on. I just pulled everything back out a week ago and it took me a minute to remember where I had sent this and what was done to it. I stumbled across this video in the process and it started coming back to me. I never really got a chance to appreciate it until now. I think Troy Hammer was the man behind the tuning? I just want to say that you did an excellent job and my Kral shoots amazing. It’s very consistent and efficient to say the least. Not to mention it hits like a tank! Thanks IA and Troy H. for the quality work!
u have some very consistent shot count without a reg, very good work u do...
I really enjoy all video from troy.how to purchase anti bounce hammer spring because i have puncher breaker .25 and already install lane regulator set at 130bar.how big transfer port should i drill to get 50ftpound .thank you
If your'e looking for 50fpe I wouldn't use a regulator. You'll probably need to up the reg to 150bar and replace the power adjuster with a 1" long 5/16-18tpi capscrew and drill all ports to 7/32" plus an internal spring 2" long that fits inside the main spring.
@@AnnihilatorAirguns thank you for the tip.how about 40fpe adjustment.can i just drill for 4.5mm for transfer port
Great job, can't wait to get mine back from ya
Damn nice tune
That is 1/2 UN , threads that Kral puncher breaker will look sweet with a suppressor moderator ,
Send a 19.91g pellet down the barrel to check velocity... I'm just curious
James Denny I don't have any but the 25.4gr is about 120fps faster. The 19.91 should be just over 1000fps on high power.
@@AnnihilatorAirgunscan u do this with a benjiman marauder 25cal...same shot count
Gerald Williams the marauder has a 212cc tube vs 280cc on the breaker so the shot count would be lower.
Hi
When i shoot mine .22 silent in full power around 855 fps its start to spread the shoots badly, in low and medium settings it shoots like a champ.
I have tried jsb jumbo and heavy 5.50 and 5.52 and nothing helps.
Do you got some ideas?
Thanks
Hey is there a solution for jamming magazines on the breaker .22?
I shoot mostly jsb jumbo 5.50mm and both magazines jams.
Thanks
Johan Safstrom the gun must remain level or pointed down during cycling. If pointed up you run the risk of jamming. I have seen the face plate being modified with good results as well. You fill in pellet loading slot so only the hole remains where the probe enters when loaded but you have to load the first pellet skirt first from the rear like the FX mags.
@@AnnihilatorAirguns Thanks for the reply
I Will give it a try to fill the hole.
And you doing a great work with your Channel Thumbs up!
@@AnnihilatorAirguns what performance could I expect from a fully tuned 25?
Was the first generation any more problematic than the 2nd generation?
They were the same. Stems and levers on both were issues. The newest ones have a stem that should be good now but still using the same levers.