Thank you for the tutorial. One question, do you hold your round bur in an angle or it is held at a 90-degree vertical line? I want to know if that makes a difference in the sitting of the stones with round burs.
It is white gold alloy mixed by me, rich in palladium, mechanical hardened. This alloy it is hard but not brittle, like some casting alloys. It is very similar to platinum. If one stone mounted by me will "fly" this stone would be the first. Thank you for asking. Coly
This is always depending of what do you want to do. Stone 2.5mm, distance minimum 2.5mm. Stone 2.5mm is the stone what can by fitted in hole made with 2.5mm burr. 2.5mm stone in reality is 2.45mm to 2.49mm. Coly
Knight Enlightened it's palladium.. Very similar to platinum.. Did u mean what the ring was made from? 🤔 or the steel the gravers were? They are high speed steel usually
Long distance it is 30cm and you have place to work under microscope. Last lens group it is interchangeable. Search for Leica Objective Lens 10422563 for Leica M, MZ, MS5, MZ6 etc Depending of this lens you can change the working distance and the amplitude. I use exactly this objective in M3Z. Coly
When you switched over to the graver is that a whole new flex shaft you have to use or is there a way to use the graver head on a flex shaft that takes burs?
The engraver he used Was done by hand I think (correct me if I'm wrong) not electric or air assisted I suppose you may be able to run a sharpened old burr to a sharp needle point and run it at High rpm and "draw" with it that's maybe though I've never tried it. Hope this helps answer your question.
gilera runner it's an air assisted graver man. It don't work in a flex shaft.. There's an easy way to make an air powered graver using an electric compressor for inflating tires.. Check out Shawn Hughes, he goes through how to make one if u are good with your hands. Or u can pick up one of these for like 200 or so
Saturdays R 4 The Boys no man, it's a whole different system. Pneumatic, air assisted.. Like a powered hammer... Check out my previous comment above. There's a few vids on how to make one by slightly modifying a small compressor you'd have in your car for inflating wheels. It's not crazy difficult.. An they are alot if fun! Hope this helps answer your question
I casting Platinum Cobalt 95-5 alloy in MC20v Indutherm furnace with Romanoff Fast Cast investment and 3Dsolidscape printing waxes. Casted rings appear with the rough surface. Is it necessary to clean or paint the waxes before adding the investment to the cylinder?
Fernando Rúa did u not just watch this video to see how it's made? 🤔 haha Coly makes jewlery by hand same as me, forged... Other more mass production stuff use molds and make many of the same rings an jewelry in one go. Reducing the costs.. But it's not unique like hand made jewlery.. I hope this answers yours question
Jos Haddow man.. U need 100s of little burs, n bits of every size and gravers or many sizes.. It's not really a question u can answer easily.. Start small an build up your collection of tools! Make some basket settings first to gain experience that's how I started.
Muchas gracias por comentar en mi canal, Mona! Ahora ponemos menos videos pero es porque intentamos hacerlos mas intretenidos. El ultimo que pusimos tiene una tendencia humoristica e intentamos ir por este camino. Dentro de 10 dias vamos a tener listo un video nuevo. Coly
Donde hacen clases? Imagino que no sera por uruguay o argentina no? Me encantaria asistir. Si tienes algun taller para recomendarme por estos lugares te lo agradezco! Estare pendiente de tus videos.
OMG!!! SO GORGEOUS! I love it. Stunningly exquisite. I want it!
Thank you so much!
Been looking for a video exactly like this on TH-cam. Never found it through searching but today it was in my recommended. Thanks so much
In this channel you can find few videos with this setting.
Thank you.
Coly
What an art producing such handmade pieces...I love the result, congratulations! 💐💐
I only do this, handmade unique piece.
Thank you for the comment, Cristobal?
Where are you from?
Coly
Love this video.. Don't know how I ended up here but I really wish you were narrating this.
We will try!
What is kind of chisel you was using in making prong around diamond seat ? Thanks
Thank you for the tutorial. One question, do you hold your round bur in an angle or it is held at a 90-degree vertical line? I want to know if that makes a difference in the sitting of the stones with round burs.
45 or 90 degree it is depending of the situation.
Working, you just feel what to do.
90 degree I not use almost never.
Coly
Great help! I'm getting into setting soon and it seems to be very intimidating. Your videos give me a better sense of how to approach it. Thanks!
Just practice and passion.
Thank you for watching and comment.
Coly
Hey, i have a question: on the end part do you bend the tiny "arms" to support the diamond from falling out and is this enough support?
It is white gold alloy mixed by me, rich in palladium, mechanical hardened.
This alloy it is hard but not brittle, like some casting alloys.
It is very similar to platinum.
If one stone mounted by me will "fly" this stone would be the first.
Thank you for asking.
Coly
Fantastic video...can't wait to try making this.
👍, @Carianin 52 !
I always get the spacing wrong. If I want to set 2.5mm stones, how far away should each pilot hole be?
This is always depending of what do you want to do.
Stone 2.5mm, distance minimum 2.5mm.
Stone 2.5mm is the stone what can by fitted in hole made with 2.5mm burr.
2.5mm stone in reality is 2.45mm to 2.49mm.
Coly
Thanks Coly
I wish I had an powered graver so I could practice more😔 is there anyway of doing such settings with out the air graver Coly? 🤔
Some say yes, you can do it with manual engraver but I have not seen it...
How is jewellery made haha I know. Iv not seen anyone do it manually also 😂.. I will get a graver soon 😉 thank u for the video
bro how did u record all this things plz let me know the equipment's
Digital camera, macro lens and wide angle lens.
I use some brands.
Thank you for asking.
Coly
*Beautiful just beautiful. New subscriber on board 👍🏼👊🏼👊🏼🇹🇹*
I am so glad! Thank you so much for your kind words.
It means so much to me.
Coly
How many sizes of Ball Burs did this project use?
What metal?
Awesome workmanship
I not remember exactly.
I like various sizes vs the big one directly.
I not remember if is carbide or hss because I use both.
Thank you.
Coly
Knight Enlightened it's palladium.. Very similar to platinum.. Did u mean what the ring was made from? 🤔 or the steel the gravers were? They are high speed steel usually
Great video. Feedback is so negative. This video is our together very nicely
This is my first video.
Thank you!
Coly
Absolutely amazing to watch
Thank you.
Coly
Just fount your channel, it’s amazing ❤️🌹
Thank you so much!!
what microscope is the best to use for stone setting ?
What price range?
Cheep under 0.5K Leica GZ6, S6D
Normal price 1K Leica M3Z
Expensive 3k or more Zeiss OPMI, STEMI
Lot of option.
Coly
How is jewellery made what is the difference. Long distance working ?
Long distance it is 30cm and you have place to work under microscope.
Last lens group it is interchangeable.
Search for Leica Objective Lens 10422563 for Leica M, MZ, MS5, MZ6 etc
Depending of this lens you can change the working distance and the amplitude.
I use exactly this objective in M3Z.
Coly
Thank you very much for a great video! May I ask how the tool you use at 5.56 is called?
Round graver.
Thank you for asking.
Coly
Amazing work!
Thank you, @Rob & Pete's Workshop!
how is it an eternity ring when the diamonds are not all around the ring ?
Eternity, half eternity!?
Sir gud day... what do u call on the tools u used in carving??? Tnx
Round graver.
When you switched over to the graver is that a whole new flex shaft you have to use or is there a way to use the graver head on a flex shaft that takes burs?
I think I do not understand your question well.
Please, reformulate the question.
Thank you!
Coly
The engraver he used Was done by hand I think (correct me if I'm wrong) not electric or air assisted I suppose you may be able to run a sharpened old burr to a sharp needle point and run it at High rpm and "draw" with it that's maybe though I've never tried it. Hope this helps answer your question.
gilera runner it's an air assisted graver man. It don't work in a flex shaft.. There's an easy way to make an air powered graver using an electric compressor for inflating tires.. Check out Shawn Hughes, he goes through how to make one if u are good with your hands. Or u can pick up one of these for like 200 or so
Saturdays R 4 The Boys no man, it's a whole different system. Pneumatic, air assisted.. Like a powered hammer... Check out my previous comment above. There's a few vids on how to make one by slightly modifying a small compressor you'd have in your car for inflating wheels. It's not crazy difficult.. An they are alot if fun! Hope this helps answer your question
Hi again Coly. Can I ask, do u ever train anybody to set stones? 🤔
Ken, send me a WhatsApp, please.
07473 920 793
Un saludo y, Obrigado!
:)
0044 7473 920 793
For 2mm band what size stone you use to set micro set
Less than 1.9mm
I casting Platinum Cobalt 95-5 alloy in MC20v Indutherm furnace with Romanoff Fast Cast investment and 3Dsolidscape printing waxes. Casted rings appear with the rough surface. Is it necessary to clean or paint the waxes before adding the investment to the cylinder?
I want to help you but I don't do casting.
Absolutely all my jewellery are hand made.
Thank you
Coly
How is jewellery made thank you
Gracias a ti!
Coly
Fernando Rúa did u not just watch this video to see how it's made? 🤔 haha Coly makes jewlery by hand same as me, forged... Other more mass production stuff use molds and make many of the same rings an jewelry in one go. Reducing the costs.. But it's not unique like hand made jewlery.. I hope this answers yours question
am new to setting stones am just wondering what the basic tool i require are
This is very round question.
Start using basic hand tools.
Coly
Jos Haddow man.. U need 100s of little burs, n bits of every size and gravers or many sizes.. It's not really a question u can answer easily.. Start small an build up your collection of tools! Make some basket settings first to gain experience that's how I started.
1:44 Do those splinters come off easily?
Nop!
I love watching this..
Thank you, @Aquarius!
Hi! Are you using a pneumatic engraver? What machine do you use for engraving?
Pneumatic graver, yes!
Which brand is not important.
Whatever you buy will serve you.
Could you please tell how wide is the ring itself? Thanks!
3.5mm, if I remember.
What’s the tool called you used before setting the diamonds. It looks like a thin backwards shovel
Where exactly?
I'm pretty sure it was the reverse end of the tweezers?
@@jcee8493 chasing tool
Its a small plate of silver. You can make it your self
Juan Cruz Hu? No it's not a small piece of silver dude! 😂 it's an air graver tool for chasing work
wow!!! es genial lo que haces!!
Muchas gracias por comentar en mi canal, Mona!
Ahora ponemos menos videos pero es porque intentamos hacerlos mas intretenidos.
El ultimo que pusimos tiene una tendencia humoristica e intentamos ir por este camino.
Dentro de 10 dias vamos a tener listo un video nuevo.
Coly
Donde hacen clases? Imagino que no sera por uruguay o argentina no? Me encantaria asistir. Si tienes algun taller para recomendarme por estos lugares te lo agradezco! Estare pendiente de tus videos.
What’s that little thing that’s used to hold the diamond in place?
Where, exactly?
How is jewellery made not the little tongs but the thing that looks like a little screwdriver that you touch on the side
Saul C I think u are talkin about the thing for pushing over the beads on to the stone? 🤔 if so it's just like a small cup burr
This is amazing. Do you teach this? Would love to learn
Yes I do!
diamondsettingschool.com/
Thank you!
Did you cast the ring? Or purchase as stock? Love the music!!!
We make each piece by hand, as you can see in other videos.Coly
Beautiful! what size are the diamonds?
2.5mm👍
Dude how many sizes of ball burs did u use? And was that a power graver? 🤩
Great job!
I use from 0.9 to the size of the stone.
I use power graver.
How much should a set of chasing tools cost? (Graver)
Lot of option here.
What size stones did you use here?
1.8-2.0mm but I don't remember exactly!
I like this ring 💍😍
Thank you!
Buen trabajo, gracias por compartir
Gracias, Jose!
Coly
Are still offering class please???
At www.diamondsettingschool.com/ you can find our availability calendar!
Thanks for asking!
Coly
Music is obnoxious
Have mercy, please!
This is our first video.
👍
Nice work! what's the thickness of the ring?
This is my first video and I don't remember.
Sorry!
Eduardo Nardi it's about 3-4ml.
Amazing.
Thank you.
Coly
Great job
Thank you, @Roger Santos Caber!
Nice 😍😍
Thanks 🤗
In awe
Thank you.
Coly
No breathing holee in the back or did I miss that
What for?
Bus Town B not necessary for small stones!! It's more for the larger crt stones really u know
How long did it took? Excelent job!
I really don't remember.
This is our first video, one year ago.
Thank you for asking.
Coly
* how long did it take :(
@@lilpenis7859 ''I really don't remember.'' He said, are you blind?
@@diegoteixeira2003 pretty sure they were just correcting the person from the first comment.
these would be better with better music
It is true👍
This is our first video.
Thank you!
Coly
Excelent !!!
Mersi.
Coly
Nice
Thank you, @Palash Ghorui !
Coly
Nice vid, but the music suxxx!!!
😩👍
then mute it
Good
Thank you.
Coly
Wow
👍
Tq
🍺
Is this platinum or platinum ?
🙄🙄🙄🤔🤔🤔
Lol
Like
Thank you, Laurentiu!
How much does a ring like this cost
In the home page of this channel you can find how to contact us.
Thank you Jasiel Amiel Vazquez Gonzalez !
Coly
👍
Thank you!
TnxXxXxXx
Good video
Thank you for watching!
👍👍👍👏👏👏👏👏
👍👍👍
You can send me new designs of women silver ring
In WhatsApp
🙄
Can u not design your own?
but r they vvs
That was a long time ago.
I don't remember this.
Sorry
Wooow
Your comments and sugestions will be greatly apreciated.
Thank you.
Coly
This music has got to go
This is our first video.
Sorry for that!
@@jewellerymadebyhand dont apologize for Tobu, this video was more enjoyable because of it.
👍
It is complicate to choice music good for everybody.