Reverse Osmosis Troubleshooting - Little or No Flow from Faucet
ฝัง
- เผยแพร่เมื่อ 21 ส.ค. 2024
- Reverse Osmosis Troubleshooting - No Flow from Faucet
thewaterfiltere... or www.waterstores....
Get a FREE REPORT on the 10 Biggest Mistakes made when purchasing water treatment equipment and how you can avoid them by going to TheWaterStoreMidland.com or check out our ecommerce store at TheWaterFilterEstore.com
Please share this video • Reverse Osmosis Troubl... For more great information about water treatment, subscribe! / waterstoremidland
At first glance Reverse Osmosis drinking water systems can appear somewhat complex. It helps if you know how they work, so I suggest you view my How a Reverse Osmosis drinking water system works video before watching this one on troubleshooting.
One of the most common concerns is very little or no water flow from the drinking water faucet, but when you check, the tank is full, which you can tell by how heavy it is. The usual cause is the tank is low on air pressure or has a torn bladder.
To remedy this situation, follow these suggestions:
Discount Pricing on Reverse Osmosis here thewaterfiltere...
1) Turn off the water flow from the source, shut off the tank and disconnect and remove the tank, I usually take it outside at this point.
2) Find the blue or black plastic cap on the bottom or side of the tank and open it to expose the metal air stem valve. If there is water leaking out of this valve or air is coming out of the shut off, the bladder is torn and the tank needs to be replaced.
3) You need to check the pressure within the tank when it is empty, so open the valve and let the water run until it is empty. If it does not empty fully, connect a tire pump or compressor to push out all of the water before proceeding.
4) Using a low range tire pressure gauge, check the pressure inside the tank, it should be between 6-8 psi, likely it will read 0 at this point. Discount Pricing and FREE Shipping on low pressure guages thewaterfilter...
5) Carefully re pressurize the tank with a bicycle tire pump or compressor to whatever it says on the tank or if nothing is noted on the tank to 6-8 psi. Do not over pressurize as you may burst the bladder!
6) Reconnect the tank and allow the tank to refill and you'll be fine. If you find the tank needs to be constantly re pressurized it is time for a new tank! Discount Pricing and FREE Shipping on RO tanks thewaterfilter...
LOVE GARY THE WATER GUY AND WANT TO LEARN MORE ABOUT WATER FILTRATION FOR YOUR FAMILY? HERE ARE SOME NEXT STEPS!
1) Sign up to keep in touch with Gary! mailchi.mp/wat...
2) LET’S CONNECT!
/ waterestore / waterestore / the-water-filter-estore / water_estore
/ waterstoremidland
3) CONTACT!
info@WaterEstore.com or info@WaterStoreMidland.com
4) SHOP!
Midland www.WaterStore...
Canada www.WaterEstor...
USA www.WaterEstor...
Please share this video! • Reverse Osmosis Troubl...
Thanks for watching!
Gary the Water Guy. #garythewaterguy #reverseosmsosissystems #waterfiltration
This guy is the man! I would only be able to a get pitchers worth of water out of my 5 gallon RO tank. I drained it all out, adjusted the PSI and now all the water in the tank comes out. Thank You!
Glad to hear it worked for you. Please share video!
Curious Why is draining needed? Would it work just pump to 6-8 psi directly(with valve closed)?
I had this problem and did exactly what this gentleman said. The whole operation took 20 minutes. Now I have almost unlimited water gushing out instead of a trickle stream. Thank you. You saved me a service call and $$$. Greetings from Cambridge, Ontario.
Excellent! Glad it helped. Greetings from Midland, Ontario. Please share video with friends and family!
I've had my system for several years and just recently the system would bring my flow to a stop after 6 or 7 oz. After watching this video I was able to drain tank and bring the PSI to 6.5 and life is all good. I was thinking about buying a new system, thanks for saving me a few bucks.
long time ago, you couldn't find this information on the internet. back then my tank had lost its capacity and so i searched the internet with no success. ended up throwing away the entire RO system and installing a new one. I tried your method on my current system and worked like a charm. Thank you
Glad to hear it worked. Please share with friends and family.
This is exactly how a really good how-to video is made. Excellent! Thank you
Glad it was helpful! Please share with friends and family.
Thank you so much for this video! I was nervous about changing the filters and the membrane on my RO system. Following the directions for start-up and waiting 6 hours to test the system, I was so disappointed with the flow of water. I got a neighbour handyman to check out my work and he approved my work. I told him it was probably the tank and this morning I followed the steps in the video and all is working perfectly with my system. Thank you, thank you, thank you!!!
Glad it helped! Please share with friends and family.
I love this guy! He is precise and to the point. Not a lot of fluff ~ just meat and potatoes and I like that! Very detailed!
Thanks! Please share with friends and family
This solved my RO tank problem! When I opened up the valve outside about 8 cups of water came out and the tanks was nearly full (by weight). Once I drained it with air pressure, set it to 6psi, 8 hour later its as good as new! thank you sir!
@@GarytheWaterGuy Sorry buddy, I dont use Facebook, but yea I shared the video with some buddies that also have RO.
Very helpful and well presented. The manual for our GE Reverse Osmosis water filter system had absolutely no information on servicing the storage tank. We would have never known how to diagnose , drain and re-inflate the tank.
Thanks.
I did it myself!!! I followed the steps in this video and the other video about the quick connect and I am now back in action with great tasting drinking water!!! THANK YOU so much this saved me a bunch of money!!
glad to hear! Please share video with friends and family!
This was very informative and is very likely the issue I'm facing with my Home Master system. The tank is very heavy and full of water yet only delivering a small amount of water from the RO faucet. I will be following this procedure tomorrow to see if I can resolve the issue.
I hope it helped!
Just installed a new RO system. Kept the old tank. Couldn't get any water out. Swapped the new tank in that was pressurized and its working perfectly. Great video. Was trying to save the new one as a backup, LOL! Thanks for the awesome video!
Glad it worked for you. Please share video with friends and family.
This was a lot of help. The water service company we had used wanted to charge us over $1000 to service our reverse osmosis filter system. We bought new filters and membranes for $300, then followed Gary's video here to bleed and recharge the tank and the system works like new. Thank you! And no, I won't send you the $700 we saved🤔
Excellent! Exactly what these videos are for. Please share video with friends and family
GARY! THANK YOU! I wish I watched this before I changed out all of the filters, but you saved me a huge headache! Only took 10 minutes
Glad to hear that it helped. Please share with friends and family.
Hi Gary, great video, thank you. I have a few questions though: If the tank bladder isn't leaking, then how does it lose pressure? What will the tank pressure be when the tank if full? How often should I check the tank pressure? Thanks, Rick
It very slowly loses pressure over many years of use. Full pressure depends on your water supply pressure. You only need to check the tank when you have very little flow and the tank is full
Thanks Gary! . This is a common problem. You helped out a lot of people. Add me to the list. I thought my filters needed replacement and was planning to change them all out. Your video saved me the grief of discovering new filters wouldn't have helped.
Glad it helped, please share with friends and family.
Had to use your expertise with my osmosis tank. After 4 years of use I could barely fill a cup. But watching your video helped me how to fix the problem.
Now the foucet has the pressure needed.
Thanks again for your help
Glad it helped Please share with friends and family.
I thought I had to call someone or get a new system but this video changed it all. Simple instructions to follow and my family and I can drink safe water again without waiting 30 minutes in between!
Glad to hear that it helped! Please share video with friends and family!
I am NOT mechanically inclined, but I was able to resolve my RO low flow problem with this information. Thank you so much!
Glad to hear it helped. Please share with friends and family.
Awesome video! Far more insightful than my local culligan store. When I called them with this same issue, the only thing they told me was to replace all the filters (which I did) and to make sure the tank was at 8 psi. Your video showed every necessary steps to fix this issue. I was just about to buy a new tank. Thanks!
Glad it helped! please share with friends and family.
Thank. You. So. Much. It's nice to have regular flow again! Like brand new! I've gone months saying to myself, "I'll deal with this later." Thanks for the straight forward video, much appreciated Sir!
You're welcome! Please share video with friends and family!
This was incredibly helpful and saved me from going to the store and buying a replacement tank that I ultimately didn't need. Thank you!
Glad to hear, please share video with friends and family.
Thank you Gary for making it simple and to the point. Excellent explanation. I wish you were closer to us so that we can employ your expertise locally.
Glad to help, please share video with friends and family. With TH-cam I can help everyone everywhere!
Thank you very much. I followed your procedures and fixed my RO system.
After 10 years, my flow decreased. This video was exactly what I needed. If saved me so much money! I feel deeply indebted to Gary (the Water Guy).
Glad to hear! Please share video with friends and family.
I had a 7yr old 5stage system much like shown in this video.. Had exactly the issue he described.. but I was getting about 12oz of water out of my system each use.. Did this test my tank literally had 0lbs of pressure in it. Too bad the company I BOUGHT my system from couldn't identify this issue for me.. and I had to find this video.. Thanks Gary!
You're welcome! Please share video with friends and family.
Hi, Gary! Thank you so much for this helpful video! I've been prematurely changing out all of my filters for years. I just wish I came across your channel and video much sooner! Thanks again and keep up the great work!
Glad it was helpful! Please share video with friends and family.
Followed your troubleshooting steps and found our tank was at 3.5psi. I pumped it until about 7.5psi. I checked it again once i put it back under the cabinet and it showed 7psi.
Let's see what happens over the next few days.
Thanks for the informative videos
It's been a month or so and the water pressure from our RO system has been excellent! I'm amazed at how simple the fix was and how 4psi can change our entire experience with our system from negative to positive.
Thank you for posting this video!
Good simple and detailed instructions. Not sure who the 110 people are giving a thumbs down...
Competitors, they don't like it when I make videos that actually help people DIY.
What a great, informative video. I was getting only 1 quart out my system at a time, even after replacing the filters, and I could not solve the problem. I then followed the steps in the video and the system is working great now. I just used it to make a gallon of tea.
Glad it helped! Please share video with friends and family!
What if I am having the problem you described but instead of the tank being full it is empty... May I please have your diagnosis and instruction? You make good videos, thank you.
that's what I"m wondering too.. did you ever find a solution for lost pressure (only builds up enough water to fill a large glass) with light (mostly empty) tank?
This worked great for me...after years of tolerating awful, slow flow. THANKS SO MUCH!
Glad it helped! Please share video with friends and family.
Gary. Thank you so much for making this so simple. We own an APEC PH90 system and this is exactly what's happening.
QUESTION: what's your opinion of the newer 'all-in-one' single filter R/O's? Both APEC and Drop make them now. I'm sure you've seen them as well.
Your welcome! Please share video with friends and family! Can you post a link to the systems you are referring to?
@@GarytheWaterGuy Hi Gary. I'm actually looking into the iSpring & Waterdrop systems 3 filter systems
Just another person chiming in to say that this video helped me solve my issue,and erything about this video is perfect. (Length,descriptions,images, etc)
Thank you very much, it's one of my older ones but I am glad you still find it usefull. Please share video with friends and family!
My Amtrol RO4 just failed after 19 years. Poor pressure at the faucet led to me determining water leaking from the schraeder valve while trying to take pressure readings. The water leaking from the schaeder valve is due to a ruptured internal rubber bladder which, in a properly functioning tank, separates the water at the top of the tank from the pressurized air chamber at the bottom of the tank (where the schraeder valve is).
Hi Gary. What you describe here sounds like our problem. We attempted to follow all of your steps. We got as far as opening the tank and letting out some of the water. When we then tried to use both a bicycle pump and a compressor to pump out the rest of the water, nothing happens. No water comes out when we use either device. It seems that the air is not getting in. The tank is still heavy so it seems there is still water in there. Any ideas what is going wrong?
Thanks for this very helpful video . My tank's psi seems to be zero. When I tried to drain the tank by pumping air into it, only half the tank was drained. The other half wouldn't come out no matter how much air I pumped into it. Would you know how to proceed from here? Much thanks !
Great question but it sounds like you need a new tank. We have them here waterestore.ca/search?type=product&q=ro*%20tanks*
You did an amazing job explaining this issue and resolving the problem.
Glad it helped! Please share with friends and family.
Thanks Gary, did this today and my system is working great.
Glad to hear, please share with friends and family!
Gary, I successfully empied my tank and hooked it back up again and it is running fine. Thankyou for the good instructions. But, while I was emptying the tank the water stopped coming out about half way empty. I had to insert a stick into the air valve to empty the rest of the water as well as alot of the air. The water came out brownish. Is that because it has rusted inside? Do I need to replace the tank? Now that it is up and running there is no sign of discoloration or off taste. What do you think?
I've never seent hat before but to be safe, I woudl replace the tank. We have them here waterestore.com/products/metal-reverse-osmosis-tank-4-gallon-ro-tank-pae-ro-132
great and helpful video. I would recomend to change your audio type to mono if the sound is only coming from one ear.
Great suggestion!
Thanks water guy! You just saved me 115 bucks! That was easy after watching your vid.
Thank you Gary the water guy, very helpful. My symptom is very slow flow at the faucet. The storage tank is full. When I push on the Schrader valve water comes spewing out of the Schrader valve. Does that mean that the bladder is broken? I did remove the tank after that and tried to remove the water. It would not come out by gravity. When I applied air pressure with a bicycle pump to the tank it probably pushed out two thirds of the water and the rest I cannot get out. Would you agree that the bladder is probably broken? The tank is a whirlpool unit and I've probably had it at least five years. Thanks.
The bladder is gone and you need a new tank. we have them here waterestore.ca/products/metal-reverse-osmosis-tank-4-gallon-ro-tank-pae-ro-132?_pos=698&_sid=c3bde8fe6&_ss=r
Thank you so much! I am so happy to have my system back and working properly. Thank you thank you thank you.
Thank you! Sooooo what if the tank is empty? Do you have a video on that?
If the tank is empty something is preventing it from producing the water to fill the tank, this video will help th-cam.com/video/jur9sS2mo34/w-d-xo.html
This video was so helpful! Thank you so much for the time you took to make this video.
You are so welcome! Please share video with friends and family!
This is exactly the information that I needed. Many thanks for a great video!
Glad it was helpful! Please share with friends and family!
This is very helpful, may have to try this soon. My pressure decreased after i replaced the first 3 filters but the pressure is not bad, so I won't mess with it, ...yet.
Glad it helped. Please share video with friends and family!
Here you go, lessons I learned the hard way (my ASO value would not operate correctly):
1) Make SURE you understand the IN & OUT ports and hook up the lines correctly to ASO valve.
2) Use ONLY hard lines to interconnect (dont use clear lines from home depot, they are too soft and value wont shutoff correctly).
3) Keep all hard tube lengths to ASO value as short as possible.
4) On all connections make sure the tubes push all the way down
5) On all post carbon filters, post filters, etc...dont plug directly into these filters, first always use a push in connector then push your tube into those connectors.
I did all above and fixed my ASO value RO system operation.
Thank you for your suggestions
Thanks, Gary! Highly recommend this channel. It made it easy to fix the problem.
Glad to help Please share with friends and family.
Great Video! We have a American Plumber WRO-3500 system and a 5 Gal. Tank. The tank was about empty in the morning after filling all night. Checked the water going into it and it's drops and not a flow or stream of water. What is the normal flow into the tank coming from the system? we just changed all filter, so they're all brand new. Is there another issue or blockage causing this? If so, where? Thanks!
Did you change the membrane. I don't know how many gallons per minute your membrane is rated for but if it is 50 , you would get about 1 gallon per hour of flow from the system. Did you add any air to the tank?
@@GarytheWaterGuy Hi, Changed to new one which is 30 GPM. Followed your instructions and it seems that the Shutoff valve is not good as the drain water never stops when tank is shutoff and main is on. Would that effect the membrane from functioning right? Shouldn't the tank be filling anyway? with new membrane removed, and no membrane installed, the tank fills out good. Is the water drinkable without the membrane? I do have the other two installed (carbon and post polishing). Thanks!
Omar J. Reyes did you replace the membrane with the same god capacity as the original one?
@@GarytheWaterGuy Hi, Changed to new one which is 30 GPM same as old one. Followed your instructions and it seems that the Shutoff valve is not good as the drain water never stops when tank is shutoff and main water is on. Would that effect the membrane from functioning right? Shouldn't the tank be filling anyway? Would this happen if the new membrane is defected or clogged. FYI: With new membrane removed, and no membrane installed, the tank fills out good. Is the water drinkable without the membrane? I do have the other two installed (carbon and post polishing). Thanks!
One "Key" point everyone fails to mention, is to replace the schrader valve first, as those bicycle valve inerds tend to fail some times, and replacing the entire tank due to the valve failing is wasteful.
I actually watched a video where the guy replaced his bladder tank, and decided to cut the old one open to see where it was leaking, and there were no leaks or decrease in pressure from the bladder due to the valve being faulty.
Also, if the tank is losing pressure, and you suspect the bladder, there should in fact be Water being expelled from the schrader valve (meaning that there is water bellow the bladder where it should NOT be (at this point you can most assuredly say the bladder is damaged, but if there is no water coming out of the schrader valve, replace the valve first (any bicycle shop will have a spare valve inner for you at a cost of a few cents))
Great video otherwise, concise and to the point 👍🏻👍🏻👍🏻
Yes, definitely if the schrader valve is the problem I would replace it before giving up on the tank.
Hi! I have water coming out my Schrader valve! I suspect that means my bladder is no good but was unable to confirm until I found your comment. Thank you!
Gary
We had a stoppage to null on water flow, it was time to change filters anyway... changed filters... the RO faucet has water coming out when open... it tastes good...
Husband thinks it isn’t goin in tank?
Is the tank becoming full after a few hours? Did you replace the membrane too?
I called water people at EasyWater
They said maybe it’s auto shut off
Thank You
We enjoy your videos
They will send component if needed.
Gary thank you for your info. Turns out my husband had the tubes kind of mixed up during the process of him trying to figure out what was going on. The filters have been replaced and he feels the tank filling up. Another words the hose that had the tank water was somehow I guess running down the sink. We got it figured out now and the tank is filling up.
@@texhotwings7521 glad to hear all is working now!
When my system was installed they only put 3.5 to 4 PSI into it. This time I did the filter change and noticed maybe half of the tank was emptying. Took the tank down to the garage and added very slight amounts of air until all the water was out. Thanks. Can only imagine how much that house call would have been.
Great video. What is missing is how much air to pump in to drain the tank. "added very slight amounts of air until all the water was out" should be a part of the video.
Thanks, Gary. My husband and I changed all the filters thinking it would fix the low flow issue. We just did this procedure. Hopefully, it will help. How long do you think it will take to refill the tank?
About 3 hours.
Thank you! My tank has the maximum pressure on the label, but not optimal pressure. Set it to 10psi and all is well.
Wow! Thank you, thank you! This fixed it and I did it myself 😀 An absolute miracle in May!
Glad to hear, please share with friends and family
any tips on getting a delivery pump setup for us people that have RO system in the basement and need to pump to the fridge upstairs?
Sure do, this video will help th-cam.com/users/shortswKMdBCeBKj0?feature=share
Thank you so much for making this video. My wife thinks I am a genius :). All the credit goes to you.
Glad it helped! Please share with friends and family so their wives will think they are geniuses too!
Thank you very much! Unfortunately, I had to replace my tank anyways, but great info!
Very helpful. No unnecessary information but all that is. Thank you so much!
Thank you for watching. Please share with friends and family.
Great video and very thorough but I'm still having problems with water flow. RO2 tank is less than 10# even after overnight regeneration. I replaced all filters this past week; however, this is the first time the membrane has a lot of scaling/salt. My RO2 and water softener is a Culligan system (AC30 and Soft-Minder Twin). Thanks in advance.
What is the precharge psi in the tank when it is empty?
This is awesome video and saved a ton of expenses ... I had problem of water not coming and I used this to fix it quickly !
Glad to hear. Please share with friends and family.
Thank you for this great video! I followed your instructions. I could not pump any air into the tank as it was so hard, and the tank was still full. Then, I used a nail to release some air from the valve, the water shot out from the opening, very strongly! I cannot explain this: Why water did not come out when I pumped, but shot out when I released the air from the valve.
Can I still repair the tank? Or, I have to buy another tank? Please help.
Thank you very much!
You need a new tank. We have them here waterestore.com/products/metal-reverse-osmosis-tank-4-gallon-ro-tank-pae-ro-132
Great video, right to the point, clear instructions.!
Robert Krajnak glad to hear you liked it. Please share with friends and family.
Hi there, thank you for your video. I went through the same process and re pressurized my tank to 6psi but now after two hours the tank is no filling up. I was hoping you can help with trouble shooting my osmosis system. I can hear the water stops flowing through the system.
Was the tankltotally empty before adding the air to 6 psi? If not check out this video th-cam.com/video/jur9sS2mo34/w-d-xo.html
THANK YOU for directing me to take the tank outside before pumping the water out. That would have been a mess!
Glad to help. Please share video with friends and family
So I have just recently changed out the pre filter and post filter and the reverse osmosis cartridges with new ones. Water coming out slower than it was with the old one. About 1 month later it’s only filtering less than a bottle amount of water a day. I can confirm the tank is pressurized at 7 PSI when empty . Do you know what the issue could be?
Thank you
Either you didn’t change the membrane or something is clogged. This video might help th-cam.com/users/livejur9sS2mo34?feature=share
I dont have a shrader valve on my Ultra finer 2 system and I have little water pressure. What do you suggest?
Repalce the tank. We have them here waterestore.ca/products/metal-reverse-osmosis-tank-4-gallon-ro-tank-pae-ro-132
Hi,
Would any of the tank issues like you've described cause water flowing to the drain line continuously? Thanks.
This TH-cam video will help you with that concern. th-cam.com/video/bO3irIVCFo0/w-d-xo.html
Thank you! Thank You! This is EXACTLY what my system is doing...will definitely follow your advice.
Glad to hear, please share video with friends and family!
But if the water has infiltrated the air side of the bladder.. doesnt that mean it's done for and very likely to just keep happening? Just released all pressure from my tank and it's still full of water.
Yes, if water comes out where the air goes in your bladder is compromised and your tank needs replacement. We have them here waterestore.ca/products/metal-reverse-osmosis-tank-4-gallon-ro-tank-pae-ro-132
Thank you for educating us. May God bless!
Our pleasure! Please share video with friends and family.
Thank you Gary. This is exactly what I needed to know!
Glad to hear! Please share!
I am confused. If you use the Schrader valve to pump up the bladder inside to get the water out, won't the air remain in there or you have a change to burst the bladder? You go on then say check the air pressure with the same valve. I guess this is a bit confusing to me.
Yes, you want the air to remain in there to push out the water. When the tank is empty you check the air pressure to make sure you adjust it to get 7 psi with the tank empty.
@@GarytheWaterGuy do you want the ball valve open when pumping the bladder back up to 7psi?
I think it might be safe to say that you should not have water coming out of the schrader valve. Correct?
Carl Bilodeau yes, that tells you that the diaphragm is ruptured and it’s time for a new tank like this one waterestore.ca/products/metal-reverse-osmosis-tank-4-gallon-ro-tank-pae-ro-132
Thank you for the repair instructions - worked perfectly.....Thanks!
Glad it helped. Please share video with friends and family.
Thank You Mr. Gary (the water guy). I have a culligan RO under the sink filtration system. The faucet fractured and broke off. The replacement is very expensive. I wanted to know if the quick release system that it came with could be negotiated around. The tube is pushed into the connectors. The current tubing girth is about an inch which brings greater pressure through the faucet. All other faucets have connections that require small girths of tubing and the quick release valves that come along with the faucets can not take the pressures, thereby, causing leaks. Thanks again. Enrique.
I have the Rain Soft tank, can't find a pressure valve anywhere! How do i re-pressurize this type of tank?
If there is no pressure valve it can't be repressurized and needs replacement waterestore.com/products/metal-reverse-osmosis-tank-4-gallon-ro-tank-pae-ro-132
Amazing advise! I did it and it worked! Thank you so much!
Hey Gary--Thanks for the video!! I took my RO tank out and dumped all water until it was empty. Then using a bicycle pump attempted to re-pressurize but pump handle was VERY hard to push. I checked pressure with 0-25 psi gauge--0 psi,. I opened the ball valve on top of the tank and attempted to use pump again--only to hear air escaping from ball valve. That tells me that the bladder is ripped--do you agree?
Yes, you need a new tank.
Very helpful! Fixed our issue. Thanks for saving us a service call.
Glad to help Please share video with friends and family!
Is a small hand pump not enough pressure to make water come out? I am not able to get any water out of my tank after the initial spurt using the hand pump.
A hand pump should work, you may need to pump it several times to get enough pressure to force the water out.
Same issue here.... I'm using a hand pump with pressure gauge, reading around 100psi, but no water come out. Valve is located UNDER the barrel. Rainsoft. Have to turn it on its side to pump.
Thank you so much for the informative video Gary! We have a large 9 gallon tank and are wondering what pressure we should fill the tank to?
7 psi when the tank is empty.
@@GarytheWaterGuy Amazing, thank you for the quick response!
@@winniedang6334 Glad to help!
Tank won’t fill, water only flows for a couple seconds until it becomes a trickle, and water flows quickly out black brine line.
Tank maintains air pressure as far as I know (can’t get a good reading from the warped air-fill valve).
Is the water pressure from the home too low, or ASO or check valve needs replaced?
Low pressure could cause that concern.
Thank you very much for your video! This helped me solve my issue :)
Great content!!! Thanks for putting this together in a very easy to follow video.
Thank you, please share with friends and family!
Thank you! Do you pressurize the bladder with the ball valve on the top of the tank open or closed?
Good question! It really doesn't matter.
Gary, Great video, My problem is that I have good flow when pressing to lever for cold water, but pressing the hot water lever generates a very weak flow of water. What do you think ??
something is clogging the hot side.
What causes the tank to go "out of whack" over a period of time?
Ie. What causes it to be "water-logged" as you call it?
PS: Thank You
Exactly what I was looking for to trouble shoot and fix the issue we were having with our RO system. Vendors asking for north of $300 just to do the same steps is troubling and just plain greed.
Glad to hear that it was helpful. Please share video with friends and family.
thanks great info. thanks for having no music in the back ground
Glad you liked it! Please share video with friends and family!
Thank you so much. It solved my issue in a few minutes!
Thank you Gary.
Rob Moss please share with friends and family.
Gary the Water Guy actually I was talking to my friend how I fix our low water filter flow by watching your videos.
Hi
My tank is empy and not filling up.I might get one glass of water.Is the tank then problem or fillters? The
system is only 4 months old.Thank you.
did u ever figure out what the problem was? obviously this guy isn’t answering u
Thank you for this video it helped me A lot. I just replaced all the filters and membrain now I have air that spurts out with the water when I turn on the drinking water faucet. And there are air bubbles in the water and doesn't hold as much water in the tank. Can you help me out?
Thank you water guy. Nice and clear, I will try.
I assume you check the pressure and repressurize the tank with the valve at the top closed? My tank doesn't have a valve at the top so I'm wondering if I can repressurize with the tank connected to the system?
What if the tank is empty? We’ve just installed an RO system and we waited 24 hours. A little trickle of water and then nothing. Tank is very light. Has about 10 lbs of pressure. It had between 5-7 when we first started. Heeeeelp!
First, drop pressure back down to 6 psi. Next, shu off the tank and open the faucet and let it trickle for about 3 hours into the sink. Then close the faucet, open the tank and it should fill. If not, contact whomever you bought it from.
I had to wind up unscrewing the top valve cap (Rainsoft) of the barrel, turning it upside down and gently shake it for any water to come out. This is after trying the hand pump method with no water coming out.
Likely the membrane is ruptured and you need a new tank.