Do you mean it was all green after resetting the firmware? That first test with just the 1-16 numbers in the boxes isn't your leveling data, they're just green to confirm it has happened. When you hit level for the first time after reset, THAT is your leveling data, so red and yellow areas you'll need to "edit". You need firmware 1.06, it now moves the print head to the location you want to edit and you can do the paper trick that you see in the last scene of this video. Otherwise, there are 100 other videos show how to do the paper trick.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Almost a year with creality. After 6 months it turned into quest- every week I need to guess why I have under extrusion or overextrusion, if I didn’t change settings. Changing hotends became just a routine. Even with the money I payed, I wish it lasts longer.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
Compensating for something in software is usually not as good as fixing the physical cause of the issue, this means less compensation is needed, and your top and bottom of your prints will be closer to parallel. This should also not be necessary out of the box and/or on all machines, but it's good that they provide a video explaining how to do it, in case you happen to need it. Plenty of other things you can sling valid criticism at Creality for, though.
Türkiyemin güzel insanları bu videoyu izleyipde ayar yaptıkdan sonra tablasının ayarı altüst olan güzel insanlar. videoda göstermiyor söylemiyorda tablayı söktükden sonra altında bulunan plastik siyah yükseltme pinlerini çıkardığınız yere takın kısa uzun şeklinde 2 çeşit pinler. kısayı uzunu yanlış takarsanız tablanız yamuk yumuk olur. sıralama şu şekilde sol ön tarafa kısa pin sağ ön tarafa uzun pin sol arka tarafa kısa pin sağ arka tarafa uzun pin bu şekilde takın yoksa nozzle tablayı sağlam çizer onun dışında kalibrasyon yapmaz. ben nerde hata yaptım diye aramayın çünkü ben baya aradım :D sağlıcakla kalın
Tablanın ebatina göre 2mm veya 4mm cam tabla kestirceksiniz yazdırma ornekrleri filament markasına göre sıcaklık değerlerine göre ayarlamanız microzey filament için 205 derece ile 210 derece arasi Ender 3 V3 Se modelcilere gelsin 👍
@@buharizm8194 ne kestirdiniz tam olarak ben yazıcıyı aldığımdam beri bu sorunla uğraşıyorum. Videodakilere ek terazi ile baktım ya 1 yada 2 köşe hep yüksek/alçak çıkıyor hatta aradaki siyah barlar yerine sarı yaylar taktım. fena olmuyor tam dümdüz elde edemiyorum.
@@sonersimsekhd 4mm cam kestir plastik barelleri değiştir 4 adet silikon ısıtıcı tabla kalibrasyon 18 mm olsun çözümü böle buldum bu yazicida gönye kacikligi var onun cozumude var kalibrasyon yaptirdigin zaman altlar 0 ile başlar üstler -0 ile başlar
Lol me too, I kinda of settled for a "ok" first layer quality. I also did the dual parts fan upgrade .The original kinda of only blows in the right side. Waay better overhangs now.
mine has printed well for 2 months , now i have stringing problems (needs new cooling fan) and for some reason i can't print a funnel.. it's all string.
Had small alignment issue which causes filament stringing. Tried manually leveling now printer won’t perform AVL nor will it get past the QR code on screen. Over it.
Your bed levelling data clearly show a Z banding as the results are much higher at the back of the plate. It will be fine for the first few layers but as it goes higher, artifacts will start showing up. You should definitely make a tutorial on fixing this.
I think this is accounted for with these machines as mine also has this. The left rear is where the heating element is located on the bed and as a bed gets warm it's always going to be a little bit warped anyways. It automatically should correct while printing with this leveling data.
@@ItzEvolvso is the representation of the numbers, when autoleveled measured from a specific point? When my kid got hers, we put it together, then did the auto level. All green but it did seem that from right side to left, it was higher just a bit. After it runs and before we hit confirm, can we “edit” each location to “0” and that would make it flat?
@@elephaux5671 I did. After multiple additional videos and attempts at getting prints to stick, I boxed it up and returned it. Have a BambuLabs A1 now. Starting over from square one.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
@@crealityafter-sale5706 I started a support case with you. My plate got hurt by the automatic z-offset program. Isn't the whole point of it to set it correctly?
@@dalle5840 Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
By "horizontal", they really mean flat / planar. This is a measurement of the surface to itself, so if it's not flat enough there is nothing to adjust (short of trying to bend the plates, which will almost certainly not go well ) - you need to replace the part.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Please create one that talks about the z offset as mine are way to high after leveling. I have 3 Se's and all have hte same issue out of the box. This tutorial was no help even after following the steps
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
I have an SE, but upgraded it with a nebula pad. The displays and options are very different. How do I get to the option to 'edit levelling data' on the nebula pad? I have some bad levelling issues and I can't even get to the settings to fix it.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
How about you tell us how to adjust the bed after checking it’s level with a ruler? Which screws? None, apparently. Just finding out if it’s not level for the fun of it I guess. I’ll never ever give another cent to Creality. Everything is like a test print.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
@@Eddddddddddddddd hi i am having problems with my ke as well. ive only had my printer a few months so i am still learning. please can you explain were you put the spacers, hope you dont mind me asking but its driving me crazy and i have been trying to fix it for 3 days xx
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
mine during the leveling, it just take the measurement i the same corner, it does not move to the different point of the table. Any idea how to fix that?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
I dont understand how placing a ruler on the heat bed, and passing a piece of paper under would show if the bed is level or not. Wouldnt the result be the same if it were 45 degrees, fully vertical?
I’m thinking they are checking to see if it’s a flat plane. If the paper slides through the back contact, but not the front of the contact, then it is warped/bent/out-of-plane
This video is not good. It does not tell you how to fix anything. What good is it for me to know my bed is not level if you don't tell me how to fix it? All i know is my recently purchased machine is broken it seems because it's not level.
They do tell you how to fix it (see part of video with glue sticks). After manually leveling the bed, you would auto level the bed through the firmware
Don't know if anyone perceived this or it's just me, after I reset the configuration, did de auto-level thing again, the printer just became way faster. Printing the exactly same Gcode
@@JaceN3D Probably that was the case... But it wasn't me, maybe it was configured from the factory. But I really didn't noticed any changes in the quality, so I left as it is.
I'm colorblind and the green and yellow mesh information really mess me up. lol Luckly there are numbers too. otherwise, I wouldn't be able to tell them apart.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
What was the point of the beginning of this video??? I was following along and suddenly, place plate and measure with paper wth! edit: oh sheesh, then after the next clip it's back off again
Dare creality 3v3se. I like mine 3v3se verry much. Bud you shut tell people to level the buildplate first whit a peace of paper . 1 you go to move . 2 you select z. Axis. 3 you dial the number to zero. Next you go to edit. 4 you geth a peace of paper. 5 . You set all 16 Points by hand. Then confirm it. 6 you store the settings. After that you let the c.r. touch do the final tuning. Dare creality. I also own a ender 3.orginale. En upgrade it. Bud the big question is when are you going to run Klipper on the machines. It runs faster . It is Smooth. Better print.s. Can your i.c.t . Team . Roll out klipper for the ender.s. And for us happy printers out there. Otherwise in the future. Where going to buy a bambu lab. And iam printing for a year. And like the possibilities on the machines. Bud iam also a software fan . And build my own p.c. That.s why a say. You goth Windows 95. Dos. Bla bla. Bud the is 2024. And there.s KLIPPER. THANK YOU IN ADVANCE
For the love of god please do not follow these instructions! I had OK results and now they are terrible and I still cannot recover from the destruction this has caused.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Thanks, it was all green except for two blues and now its all yellow and red 👍👍
You shouldn't run this consequtively
Do you mean it was all green after resetting the firmware? That first test with just the 1-16 numbers in the boxes isn't your leveling data, they're just green to confirm it has happened. When you hit level for the first time after reset, THAT is your leveling data, so red and yellow areas you'll need to "edit". You need firmware 1.06, it now moves the print head to the location you want to edit and you can do the paper trick that you see in the last scene of this video. Otherwise, there are 100 other videos show how to do the paper trick.
I’ve done everything as in video. Before my table leveling was green, now red and yellow. Thanks for the education)
Is that a good or bad thing, I genuinely don't know
@@kronandank6007not good
its bad, hes just trolling. what u want is all green around 0.1-0mm@@kronandank6007
Green is good@@kronandank6007
never change a running system
Why is there no test shown in the video in the program Creality Print? why didn't you post a test STL file under the video?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Almost a year with creality. After 6 months it turned into quest- every week I need to guess why I have under extrusion or overextrusion, if I didn’t change settings. Changing hotends became just a routine. Even with the money I payed, I wish it lasts longer.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
Where can I get the same model for test print?
@crealityafter-sale5706 where can I find the model for this test print?
Yeah can we have a direct Link to this leveling bed test?
It’s in creativity print software
@@GageVibes I assume you mean Creality Print, right? Would you mind sharing how to find the test print in the softgware?
@@TheImprovisations sure thing
And doesn’t that defeat the purpose of full auto levelling what’s the point of it having a CR touch if it still needs manual tuning
Compensating for something in software is usually not as good as fixing the physical cause of the issue, this means less compensation is needed, and your top and bottom of your prints will be closer to parallel. This should also not be necessary out of the box and/or on all machines, but it's good that they provide a video explaining how to do it, in case you happen to need it.
Plenty of other things you can sling valid criticism at Creality for, though.
@@MrJelle18 Yep I had to manually level the gantry because I was not getting proper leveling readings
CR touch is really not the "best" auto leveling technique... Is just a Ok solution.
@@soniccinos What would you recommend instead?
If only their auto leveling would have worked. All it does for me is just screw everything up.
Türkiyemin güzel insanları bu videoyu izleyipde ayar yaptıkdan sonra tablasının ayarı altüst olan güzel insanlar. videoda göstermiyor söylemiyorda tablayı söktükden sonra altında bulunan plastik siyah yükseltme pinlerini çıkardığınız yere takın kısa uzun şeklinde 2 çeşit pinler. kısayı uzunu yanlış takarsanız tablanız yamuk yumuk olur. sıralama şu şekilde
sol ön tarafa kısa pin
sağ ön tarafa uzun pin
sol arka tarafa kısa pin
sağ arka tarafa uzun pin
bu şekilde takın yoksa nozzle tablayı sağlam çizer onun dışında kalibrasyon yapmaz. ben nerde hata yaptım diye aramayın çünkü ben baya aradım :D sağlıcakla kalın
bende uzun uğraşlar sonuncunda cözümü buldum videoda gosterilen z ofset icin tablayı yerinden sökmeye grek yok .
Tablanın ebatina göre 2mm veya 4mm cam tabla kestirceksiniz yazdırma ornekrleri filament markasına göre sıcaklık değerlerine göre ayarlamanız microzey filament için 205 derece ile 210 derece arasi Ender 3 V3 Se modelcilere gelsin 👍
@@buharizm8194 ne kestirdiniz tam olarak ben yazıcıyı aldığımdam beri bu sorunla uğraşıyorum. Videodakilere ek terazi ile baktım ya 1 yada 2 köşe hep yüksek/alçak çıkıyor hatta aradaki siyah barlar yerine sarı yaylar taktım. fena olmuyor tam dümdüz elde edemiyorum.
@@sonersimsekhd 4mm cam kestir plastik barelleri değiştir 4 adet silikon ısıtıcı tabla kalibrasyon 18 mm olsun çözümü böle buldum bu yazicida gönye kacikligi var onun cozumude var kalibrasyon yaptirdigin zaman altlar 0 ile başlar üstler -0 ile başlar
Not: Eğer kalibrasyon da gene hata varsa hazırlık Z ekseni telafi ayarını eğer mesala 2.06 çıktı sen onu -2.06 getir
These comments are fantastic. My issue was the subtitles! What were they thinking. 😂😂😂😂😂😂
Haha
It’s an Ender alright, as in hobby Ender, lol!
I’ve had mine for two months and still can’t get consistent results.
Extruder fan is loud as hell too.
Lol me too, I kinda of settled for a "ok" first layer quality. I also did the dual parts fan upgrade .The original kinda of only blows in the right side. Waay better overhangs now.
mine has printed well for 2 months , now i have stringing problems (needs new cooling fan) and for some reason i can't print a funnel.. it's all string.
@@chriskwakernaat2328hi, do you solve youre problem? i have the same issues
@@egeef2425 i used another slicer and it worked. orcaslicer. i think i changed settings in the creality slicer some how.
Skill diff.
Had small alignment issue which causes filament stringing. Tried manually leveling now printer won’t perform AVL nor will it get past the QR code on screen. Over it.
Your bed levelling data clearly show a Z banding as the results are much higher at the back of the plate. It will be fine for the first few layers but as it goes higher, artifacts will start showing up. You should definitely make a tutorial on fixing this.
I think this is accounted for with these machines as mine also has this. The left rear is where the heating element is located on the bed and as a bed gets warm it's always going to be a little bit warped anyways. It automatically should correct while printing with this leveling data.
@@ItzEvolvso is the representation of the numbers, when autoleveled measured from a specific point?
When my kid got hers, we put it together, then did the auto level. All green but it did seem that from right side to left, it was higher just a bit.
After it runs and before we hit confirm, can we “edit” each location to “0” and that would make it flat?
@@nsanerydahnononono nooooo please do not do that, you will ruin your printer. I hope you realised this before it was too late.
@@elephaux5671 I did. After multiple additional videos and attempts at getting prints to stick, I boxed it up and returned it. Have a BambuLabs A1 now. Starting over from square one.
Where do you get the STL file (adhesion test with squares) printed at 3:40?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
@@crealityafter-sale5706
Y’all a joke, just like your printers.
How to edit leveling data on V3 KE?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
If you go to settings you can adjust them
Auto levelling and the auto z-offset on this printer does not work.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
@@crealityafter-sale5706 I started a support case with you. My plate got hurt by the automatic z-offset program. Isn't the whole point of it to set it correctly?
@@dalle5840 Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
What to do if plates are not HORIZONTAL?
By "horizontal", they really mean flat / planar. This is a measurement of the surface to itself, so if it's not flat enough there is nothing to adjust (short of trying to bend the plates, which will almost certainly not go well ) - you need to replace the part.
@@RonnieTheFinBear Buy silicone spacers
@@Eddddddddddddddd and exactly where are you going to put those spacers?
Was all green, now upgraded with Nebula and it's all Blue, highest number is 0.41 is that blue the new green and is 0.41 too high?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Please create one that talks about the z offset as mine are way to high after leveling. I have 3 Se's and all have hte same issue out of the box. This tutorial was no help even after following the steps
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
I have an SE, but upgraded it with a nebula pad. The displays and options are very different. How do I get to the option to 'edit levelling data' on the nebula pad? I have some bad levelling issues and I can't even get to the settings to fix it.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
really useful video. thanks!
How about you tell us how to adjust the bed after checking it’s level with a ruler?
Which screws? None, apparently. Just finding out if it’s not level for the fun of it I guess.
I’ll never ever give another cent to Creality.
Everything is like a test print.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
What about when I can’t get it to even print the test
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Auto levelling on ender 3 v3 ke printer does not work - can you assit?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
how do you adjust the auto levelling data with the KE?
Don't do it like in the video. Buy silicone spacers 16mm-2pcs 14mm-2pcs and adjust the table. Or cut 2mm from 16mm.
@@Eddddddddddddddd hi i am having problems with my ke as well. ive only had my printer a few months so i am still learning. please can you explain were you put the spacers, hope you dont mind me asking but its driving me crazy and i have been trying to fix it for 3 days xx
@@vikkidyer the same shit has been going on for over a month
Good morning. Where can I download the test stl shown in the video?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
mine during the leveling, it just take the measurement i the same corner, it does not move to the different point of the table. Any idea how to fix that?
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Facebook official service : facebook.com/crealitysupport)
Need to upgrade your firmware
problem fixed ty
I dont understand how placing a ruler on the heat bed, and passing a piece of paper under would show if the bed is level or not.
Wouldnt the result be the same if it were 45 degrees, fully vertical?
It's bad translation. I think they meant it's not warped.
I’m thinking they are checking to see if it’s a flat plane. If the paper slides through the back contact, but not the front of the contact, then it is warped/bent/out-of-plane
This video is not good. It does not tell you how to fix anything. What good is it for me to know my bed is not level if you don't tell me how to fix it? All i know is my recently purchased machine is broken it seems because it's not level.
They do tell you how to fix it (see part of video with glue sticks). After manually leveling the bed, you would auto level the bed through the firmware
@@johnnguyen4128 That's great for the X-axis gantry adjustment, but what about the Y-axis?
Contact their creality support, your machine should still be in the warranty period. They’ll send you replacement parts for free
@@winklerchry axis is merely off balanced cause it’s on a double horizontal screw bars so there's a little chance it's not leveled by default
Don't know if anyone perceived this or it's just me, after I reset the configuration, did de auto-level thing again, the printer just became way faster. Printing the exactly same Gcode
Maybe you previously had your max acceleration and speed settings turned down?
@@JaceN3D Probably that was the case... But it wasn't me, maybe it was configured from the factory. But I really didn't noticed any changes in the quality, so I left as it is.
Where can I find this leveling test file???
Printables
@@Gcatalanaladren where?
@@tomasdamjanic1 search levelling test
I'm colorblind and the green and yellow mesh information really mess me up. lol Luckly there are numbers too. otherwise, I wouldn't be able to tell them apart.
Donde puedo conseguir el stl de test????
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
I go into edit level date and the print head doesn't move to that area to test with a piece of paper what do i need to do to fix this?
Are you on version 1.0.6?
@@samuelsingh7289I'm not
@e-manyvelez7430 you should update. I noticed it was missing in version 1.0.4
@@samuelsingh7289 I tried updating but it said I need a a fat 32 formatting and my sdcard only does exfat
What did you figure out? Cuz same..
So I slowed the video down to .75x speed… music still annoying instructions still don’t make sense
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Добавьте субтитры для автоперевода
How do I find what version of software is my printer is using?
under control then info
What was the point of the beginning of this video??? I was following along and suddenly, place plate and measure with paper wth! edit: oh sheesh, then after the next clip it's back off again
Dont bother with auto bed level. Take out the spacers, add some yellow springs and adjust manually. Creality autobedlevelling sucks
So in this video you admit that your "auto levelling" function doesnt work.
Dare creality 3v3se.
I like mine 3v3se verry much.
Bud you shut tell people to level the buildplate first whit a peace of paper .
1 you go to move .
2 you select z. Axis.
3 you dial the number to zero.
Next you go to edit.
4 you geth a peace of paper.
5 . You set all 16 Points by hand.
Then confirm it.
6 you store the settings.
After that you let the c.r. touch do the final tuning.
Dare creality.
I also own a ender 3.orginale.
En upgrade it.
Bud the big question is when are you going to run Klipper on the machines.
It runs faster .
It is Smooth.
Better print.s.
Can your i.c.t . Team .
Roll out klipper for the ender.s.
And for us happy printers out there.
Otherwise in the future.
Where going to buy a bambu lab.
And iam printing for a year.
And like the possibilities on the machines.
Bud iam also a software fan .
And build my own p.c.
That.s why a say.
You goth Windows 95.
Dos.
Bla bla.
Bud the is 2024.
And there.s KLIPPER.
THANK YOU IN ADVANCE
the music is so terrible
For the love of god please do not follow these instructions! I had OK results and now they are terrible and I still cannot recover from the destruction this has caused.
Hi, if you encounter any problems, please feel free to contact our after-sales service and they will help you solve the problem as soon as possible. (Official service email: cs@creality.com)
Leave it to Creality to make yet another useless video
If you trimmed your fingernails, then the printers would be better...