Very nice video... I've done very similar and learning a lot.. the alternating holes between neutrals only blocked flow.. if you're using tap water you get brown sludge, distilled water stayed clean.. so take use of tap water.. !!!.. You'll find flux leakages from the hole causing a burn mark on the opposing plate.. oxidisation side of current flow... Nice video .. Thom in Scotland.
You can also reuse an old battery casing to make wetcell instead of drycell. Battery casing are made the way they are because it's the best way to hold a corrosive electrolyte with the least chances of leakage.
The night hawk in light channel had made a similarly project with a flash arrester. You might want to check out that channel for some possible flash arrester designs.
next video i want you to make video about fill balloon with lead acid battery beacuse when charge it produces hydrogen can you make video about it using a hole from battery when charge to balloon it can fly up! can you do video about it?❤
Hi, I'm looking for a bit of advice here, I'm looking to purchase off eBay some, silver solder , ( rods as you have ) .. and a hand held torch, used for browning food , daft as it seems it gets up to a fine temperature.. the flux type confuses me some what...so any experience advice welcome... 316 s/s ... 0.90 mm thick ... Whilst strips also .... s/s are ONLY 0.20 mm thick to allow me .manipulation of lead offs.. Correct flux type is confusing.. any advice gratefully received... Thom in Scotland.
Hi Thom. You can go to a refrigeration spares shop. They will have that there. I'm an industrial refrigeration tech and I use silver solder often. You can buy the rods that are already coated or you can buy the rods that are not coated and buy the powder flux seperate, which I prefer because the rods that have the flux on seem to loose the flux quiet easily when you store them and it's quite brittle. You can buy the brazing torch there aswell called a map gas.
You also need to heat up the thicker plate first then till cherry red then the thinner plate. You have to play with the heat till the 2 metals are the similar temperature then if you have a rod without flux, heat the rod and dip the rod into the flux powder. Heating the rod allows the flux to stick to the rod.
@@fuelban I'm in the process of building another fuel cell that separates the oxygen and hydrogen. Then I'm hoping that I'll be able to control or know exactly how much hydrogen I'm putting into the engine. I'll post that video hopefully soon.
Hydrogen technology 🚓🚕 Hydrogen help the combustion process to run engine more efficieently.and carbon-free fuel burnning. HHO gas burn a lot faster then gasoline or petrol. Hydrogen power miracle gas remove carbon build up in the combustion chamber and boost engine power and torique. Reduse carbon emission ) restores better fuel economy. Hho car kit prolonging engine life and engine oil life. Like a new car!!! Engine runs smoother and cleaner to make your car 0 carbon emissions Boost engine power and torque Better acceleration . An efficient hho car kit lower the engine temperature more then 100 degree F. Hho car kit reduce car maintenance charges. Cleaner engine running. Reducing engine noise due to the faster fuel burning. Hho car kits works nicely requires no modifications in the car engine. No side effects on car engine. Engine start quickly safe your car battery. No more petrol or diesel smoke or smell. Hho system is very simple. Hho kit installation time is about two hours to make your car a low cost hy-brid.
Brilliant. Love the narration, can’t wait to see the engine running on hydrogen.
Awesome video. Can't wait to see that generator work with the HHO generator.
Very nice video... I've done very similar and learning a lot.. the alternating holes between neutrals only blocked flow.. if you're using tap water you get brown sludge, distilled water stayed clean.. so take use of tap water.. !!!.. You'll find flux leakages from the hole causing a burn mark on the opposing plate.. oxidisation side of current flow...
Nice video ..
Thom in Scotland.
Very cool.
You can also reuse an old battery casing to make wetcell instead of drycell. Battery casing are made the way they are because it's the best way to hold a corrosive electrolyte with the least chances of leakage.
I've also built one. I see you are a south african. Man, please send me your details to discuss this. The possibilities are endless!
Tus juntas de que material son.??
Good piece of work.
Where is the video of making a flash arrester. And please can you make a hydrogen oxygen separator system.
Hi Magnet man, I tried making a separator but failed miserably. So back to the drawing board. But definitely in the near future.
@@yourworkshopmate372
😆
InshaAllah
There is an expensive way resorted to be industries
And a cheaper way as done by "inventive" YT channel.
The night hawk in light channel had made a similarly project with a flash arrester. You might want to check out that channel for some possible flash arrester designs.
next video i want you to make video about fill balloon with lead acid battery beacuse when charge it produces hydrogen can you make video about it using a hole from battery when charge to balloon it can fly up! can you do video about it?❤
Hi, I'm looking for a bit of advice here, I'm looking to purchase off eBay some, silver solder , ( rods as you have ) .. and a hand held torch, used for browning food , daft as it seems it gets up to a fine temperature.. the flux type confuses me some what...so any experience advice welcome...
316 s/s ... 0.90 mm thick ... Whilst strips also .... s/s are ONLY 0.20 mm thick to allow me .manipulation of lead offs..
Correct flux type is confusing.. any advice gratefully received...
Thom in Scotland.
Hi Thom. You can go to a refrigeration spares shop. They will have that there. I'm an industrial refrigeration tech and I use silver solder often. You can buy the rods that are already coated or you can buy the rods that are not coated and buy the powder flux seperate, which I prefer because the rods that have the flux on seem to loose the flux quiet easily when you store them and it's quite brittle. You can buy the brazing torch there aswell called a map gas.
You also need to heat up the thicker plate first then till cherry red then the thinner plate. You have to play with the heat till the 2 metals are the similar temperature then if you have a rod without flux, heat the rod and dip the rod into the flux powder. Heating the rod allows the flux to stick to the rod.
Thanks, good guidelines information... Will order of eBay and let you know how I get on.. meny thanks.
Thom in Scotland.
@@fuelban I'm in the process of building another fuel cell that separates the oxygen and hydrogen. Then I'm hoping that I'll be able to control or know exactly how much hydrogen I'm putting into the engine. I'll post that video hopefully soon.
@@yourworkshopmate372 ...
Nice one, I've subscribed so will get you're posting of video.... Thanks.
Thom in Scotland.
Hydrogen technology 🚓🚕
Hydrogen help the combustion process to run engine more efficieently.and carbon-free fuel burnning.
HHO gas burn a lot faster then gasoline or petrol. Hydrogen power miracle gas remove carbon build up in the combustion chamber and boost engine power and torique. Reduse carbon emission ) restores better fuel economy.
Hho car kit prolonging engine life and engine oil life.
Like a new car!!!
Engine runs smoother and cleaner to make your car 0 carbon emissions Boost engine power and torque Better acceleration .
An efficient hho car kit lower the engine temperature more then 100 degree F. Hho car kit reduce car maintenance charges.
Cleaner engine running. Reducing engine noise due to the faster fuel burning. Hho car kits works nicely requires no modifications in the car engine. No side effects on car engine.
Engine start quickly safe your car battery. No more petrol or diesel smoke or smell. Hho system is very simple.
Hho kit installation time is about two hours to make your car a low cost hy-brid.
My cell shorting when i connect it to battary why is it happnenig
Prolly two opposite plates are directly touching each other.
If yeah, increase distance and improve isolation
Graffiti works batter than staneles still.
Oh ok thanks for the comment, could you please give me an explanation thanks