Called a flashback, all the hydrogen in line line is exploding, thats why we have the bubbler. If there was nothing stopping the hydrogen from flashing back into the main container it would blow it self up.
I dont think these are "full" flashbacks though(probably just inside the torch) since a flashback all the way to the bubbler would make your ears ring and probably blow some tubes off their connections.
How much current does a setup like this take? Could you run a unit like this in a car off an alternator and inject it into the intake so it would actually give you a positive result in energy used vs created?
each side of the neutral plates become opposite polarity ,the further away from one polarity you go,the more closer to the other polarity it becomes,it gives in essence more little + and - cells,from the most negative end each neutral plate face will become negative or positive,so one face of a neutral plate will be more negative or positive than the other side of the same plate -,+-,+-,+-,+ this would be negative supply at one end then three neutral plates then the positive supply at the far end,as Do R/C! says,voltage dividers,they even out and share the potential(voltage).
I have seen many generators, but could you tell me what dimensions the cells have and what voltage you supply to obtain such a large quantity of hydrogen?
Good job, nicely done. I like to see so many people doing hydrogen tests. I also made a few hydrogen generators, the problem is that I don't have much time for that. good video, i love hydrogen ❤️👍🏼
Distilled water doesn't conduct. It's the minerals and impurities that make water conductive. He's just using the least corrosive means to make the water it's most conductive. Could use salt water but it creates corrosion. It all depends on what your tap water has in it. More than likely you have hard water that will work just fine or even better but then you have the corrosion and calcium scale build up on the plates.
Probably not as well due to the extra unknown-containments that he can't possibly account for. Adding a verified amount of a substance would allow him to produce Hydrogen and Oxygen at a rate he could control, unlike with tap water which can change time to time. :)
Good afternoon, your generator is magnificent, what possibility is there to have detailed information to mount the system in the kitchen to replace the gas
Sir could you help me out i have steel plate 202 and of 3 inch diameter so how much positive and negative plates i add to get optimum result and water no heated
doesn't more volts make more hydrogen?? sorry if it might be a stupid question but i don't know anything of this and i'd like to build one of this generator
More volts AND more plates can make more hydrogen.The most efficient hydrogen production happens when you apply 2.5 - 3 volts per plate.If you just increase the voltage it will not increase the production as much.
I'm curious as to what this style of drycell hho generator is capable of yielding, and at what voltage & amperage level? Also, is this solely the only type of application you use this generator for?
The residue on the plates is due to the use of brass bolts is simply made a galvanic reaction (the chemical added will support this further). Use stainless steel in all parts and get rid of residue + rust/oxidation. Btw..a flame arrestor would be a must-have safety feature. I almost wanted to say "Happy new year" as you melted the nail.. You can fabricate one by yourself a tube and some stainless steel wool is all it takes to be safe. Nice generator setup.
questions adding sodium or pottasium does it affect the quallity of oxygen ? can u breath it ? does actually make someone feel "better" breathing just oxygen ? what about hydrogen ? what happens to the hydrogen coming out of the electrolysis ? where it goes ? in order to make the blowtorch u make a small tip at the end so oxygen comes out at higher speed ?
you probably explained this in a previous video, but how do the plates stay immersed in water? most models ive seen built involve the plates being in a tank of water where as here you just have a pump going
I don't really know a lot about this, but at a guess I'd say you probably could, but it wouldn't be the most efficient kind of torch to use. But again, I don't really know.
A suggestion, use a striker for lighting the flame, I have seen people use small lighters to fire up torches before and the lighter blow up in their hand because the flame ran down into the fuel, or the flame melted a hole in the lighter.
How do you avoid explosions? I have a second container where hydroxy rises in and to a tube. When i lit my torch which was a tube and a needle, it blew the lid off the jar.
This (HIPER-VOLTIC-HHO) reactor can be serviced while running. Close lower valve remove lower reservoir empty AND replace. Open valve add (HV) premix to upper resivour, check again in 60 hours repeat if needed
Hello Sir. Does this system that you made, DOES it SEPARATE the hydrogen and oxygen gases? In other words, the gases come out separately from the generator or do they separate on the plates but come out together through the same outlet? Thank you very much for your reply.
is that Astron VS-70M-AP power suply?if i have to use in my car wich power suply or power regulator(amp and volt regulator) will you recomend me?please give a link of a regulator for my car
You have your holes at same place so your plates can't create so much that way. It's better to have first plate 2-3 holes at the bottom and next plate 3 holes on left side, next 3 holes on right side etc until last plate where the exit is and have 3-4 holes at top to get best effect out of everything. I use 22 plates, size 150mm x 150mm and gives me plenty of HHO.
since both the oxygen and the hydrogen outlet go into the water reservoir and hydrogen torches reach their insane high temperatures, I think it's both ^^
havent had to clean mine since I bought it 3 years ago.. thing is... the plates arent just normal stainless.. they're 316L grade stainless... which is the most resistant to grain boundary carbide precipitation.. aka the leaching of iron into you water.. I also use 9x distilled water so it has no mineral's or elements in it either. still looks like when I bought it.
i am not very good with this concept as this is my first time watching HHO stuff. what do the neutral plates do? 1 positive plate in the middle and 1 each negative plate at the ends and a bunch of neutral plates in the middle. i dont understand this setup. whats the purpose of the neutral plates between the + and - plates? thanks
Is the cell itself heating in normal usage? I wonder what is the efficiency of the cell.. If the PSU supplies for example 500W, is 400W transferred for heating the water and 100W for producing HHO?
That's a neat generator! How long can you run that generator for till you need to fill it up again? And do you know what temperature the generator operates at?
next time bro try to focus on the camera the outcome gas results... i saw only water bubbling didn't saw the ouput gas... anyway so amazing bro you did and excellent job... I would like to ask you if i could convert this gas into cooking gas just like gas stove?
+Ornf But for real, there is also a possibility of yielding the same amount of energy. Satisfying the definition of efficient which was the original question. So I wanted to address the question to that extent.
What are those pops when you were melting the nail?
Called a flashback, all the hydrogen in line line is exploding, thats why we have the bubbler. If there was nothing stopping the hydrogen from flashing back into the main container it would blow it self up.
popcorn
sounds like electrical arcs
I dont think these are "full" flashbacks though(probably just inside the torch) since a flashback all the way to the bubbler would make your ears ring and probably blow some tubes off their connections.
It's impurities in the steel nail. The nails had a little bit a rust on it so it was probably the small amounts of Iron-Oxide (rust) that was popping
What purpose do the neutral plates serve? do they just add space for the water to build up in or do they do something else?
they add volume.. for more water
How much current does a setup like this take? Could you run a unit like this in a car off an alternator and inject it into the intake so it would actually give you a positive result in energy used vs created?
are the plate sizes and thicknesses critical? What are the dimensions you used?
Hi Sir
Can you please let me know the voltage and ampherage you have used for power supply and the size and thickness you have used for the plates.
Im sure this is a stupid question but what is the purpose of the neutral plates on the system?
Nevermind. They are used as votage dividers..
each side of the neutral plates become opposite polarity ,the further away from one polarity you go,the more closer to the other polarity it becomes,it gives in essence more little + and - cells,from the most negative end each neutral plate face will become negative or positive,so one face of a neutral plate will be more negative or positive than the other side of the same plate -,+-,+-,+-,+ this would be negative supply at one end then three neutral plates then the positive supply at the far end,as Do R/C! says,voltage dividers,they even out and share the potential(voltage).
hi! what thickness are the gasket and steel??
I have seen many generators, but could you tell me what dimensions the cells have and what voltage you supply to obtain such a large quantity of hydrogen?
Great walkthrough! But... 5 neutral plates means 6 gaps. 2.3V between each plate, yes?
You're right! My mistake, thanks for catching that :)
+carsandwater do a face reveal
he has videos with his face in them
+TexasSmoking Jesus that was the fastest homophobic response I've ever seen for a TH-cam comment, that was literally less than a minute
+joyfullalmonds Now let's talk about religion and make parallels involving the nazis...
While melting the nail are the Sparks from the zinc in the nail metal?
I think it's rust. Iron-Oxide (rust) has O2 in it and O2 will explode if exposed to an open flame.
i agree, it's rust. Similar to a thermite reaction
Are all the plates connected to the system ?
All that gunk on the plates, is that just from impurities from the water?
Hello.I want to ask about your alkaline electrolyzer?Operating voltage? How much electricity is required to produce 1 M3 of hydrogen? Thank you.
felicidades!!! cuanto voltage le aplicaste y cuantos ampers!!!
I wanna ask if you have fire arrestor or any kind of protection ?
Good job, nicely done. I like to see so many people doing hydrogen tests. I also made a few hydrogen generators, the problem is that I don't have much time for that. good video, i love hydrogen ❤️👍🏼
Do you put something like water betwen these plates or what ??? i don't understand how it works ..
The plates are too smooth. They should be crosshatched with large grit sandpaper to enhance the production.
Hi can i asked for the dimensions of the stainless steel youve cut in mm? Thanks
Have you tried to weld aluminum? Is it ok to use it for aluminum welding?
Do you have to replace the metal that causes oxidation?
how well will it function with normal tap water ? Compared to your solution.
Distilled water doesn't conduct. It's the minerals and impurities that make water conductive. He's just using the least corrosive means to make the water it's most conductive. Could use salt water but it creates corrosion. It all depends on what your tap water has in it. More than likely you have hard water that will work just fine or even better but then you have the corrosion and calcium scale build up on the plates.
so it will just have to be cleaned and have som parts swapped out more often.
Probably not as well due to the extra unknown-containments that he can't possibly account for. Adding a verified amount of a substance would allow him to produce Hydrogen and Oxygen at a rate he could control, unlike with tap water which can change time to time. :)
It would be OK at first but soon clog up with contaminants and get very dirty very quickly.
+Joey Bartlett انت في قرقر كتير اني بورلي
Where/how can I get the gaskets that serve as spacers? Can they be custom-fitted?
Nice video. Where did you get the white plastic material?
Is oxygennproduxed OK to breathe or is it dry or something
Hi. What is the function of the membrane covering the electrode?
I don't suppose you would be willing to put up a detailed parts list somewhere?
Can you buy "Brown gas" or do you have to buy the hydrogen and oxygen separately?
No, you can't buy it. If you try to store it, all you are doing is making a bomb.
+rocketman221projects You probably just got placed on a government watch list
how many days the water will last in the container?How many cup is to be refill in every week?
What is the exact function of the safety bubbler?
How often do you need to rebuild them?
what was that grey plastic film that said 40 MIL?
Good afternoon, your generator is magnificent, what possibility is there to have detailed information to mount the system in the kitchen to replace the gas
How long does it take to make it in that state?
Question master. Can i compress the gas to a tank and use it later?
No It will explode
have you ever heard of the hindingburg blimp... ???
2:18 Be careful grinding that. It's possible that the stainless can create some chromates which are strongly carcinogenic.
hi, the power that you use is 50 V 15 amps or 50 amps 15 V???
Sir, Can we do brazing also. WHere from we will get kits for purchase and its cost may please intemated
Do you really need the gasket on the last plate next to the non conductive end cap?
Only if you don't want it to leak
Im curious if the brass is leaving the stains
What is the distance between to plates ( gasket thickness ) ?.
Sir could you help me out i have steel plate 202 and of 3 inch diameter so how much positive and negative plates i add to get optimum result and water no heated
doesn't more volts make more hydrogen?? sorry if it might be a stupid question but i don't know anything of this and i'd like to build one of this generator
More volts AND more plates can make more hydrogen.The most efficient hydrogen production happens when you apply 2.5 - 3 volts per plate.If you just increase the voltage it will not increase the production as much.
I'm curious as to what this style of drycell hho generator is capable of yielding, and at what voltage & amperage level? Also, is this solely the only type of application you use this generator for?
Ciao ottimo video. Posso chiedere perchè è meglio usare delle placche neutre anziche polarizzarle tutte? Grazie
I've been waiting for years... for the build... but the build/rebuild is good enough!
Woooow!!! is incredible and amazing, congratulaciones friend, saludos desde cuautla México!
Have you tried to weld some metalls with it? Is it good to use it for aluminum or steel welding?
Tigran Ohanyan *brazing
I have a question, does the generador heats up fast? Or for how long it can be running? Awesome vídeo.
The residue on the plates is due to the use of brass bolts is simply made a galvanic reaction (the chemical added will support this further). Use stainless steel in all parts and get rid of residue + rust/oxidation.
Btw..a flame arrestor would be a must-have safety feature. I almost wanted to say "Happy new year" as you melted the nail..
You can fabricate one by yourself a tube and some stainless steel wool is all it takes to be safe.
Nice generator setup.
Can you separate the gases H and O for a safety use with this eletrolyser?
Was the loud knocking noise when you melted the nail flashbacks?
questions
adding sodium or pottasium does it affect the quallity of oxygen ? can u breath it ? does actually make someone feel "better" breathing just oxygen ?
what about hydrogen ? what happens to the hydrogen coming out of the electrolysis ? where it goes ?
in order to make the blowtorch u make a small tip at the end so oxygen comes out at higher speed ?
you probably explained this in a previous video, but how do the plates stay immersed in water? most models ive seen built involve the plates being in a tank of water where as here you just have a pump going
Probably a dumb question but could you weld with this?
I don't really know a lot about this, but at a guess I'd say you probably could, but it wouldn't be the most efficient kind of torch to use. But again, I don't really know.
I would say you could do some serious brazing! It melted a nail and cut that metal! I would like detailed plans on this.
What is the gas flow of your generator? How much litre per hour?
Which Material is Neutral Plates Made of carsandwater?
same as other plates but are not connected to either + or -
A suggestion, use a striker for lighting the flame, I have seen people use small lighters to fire up torches before and the lighter blow up in their hand because the flame ran down into the fuel, or the flame melted a hole in the lighter.
can you please tell me what thing you put in the water.
about how fast is the flow of hydrogen with what you have set up now?
sounds good, but water reserve will finish more fast than petrol. We need make something diferent for extract the HHO.
Like what ?
@@Thefeelingofthebeautifulnature oil/petroleum**
can you please tell me that how much potassium hydroxide is to be added in tap water or distilled water, ,?
Whats the popping noise when your melting the nail?
Could a person put a in line pump.to get more pressure.
What purpose does the safety bubbler serve?
it prevents the flame from running back up the tube, if a flame reached the generator , you would have a dangerous explosion.
How do you avoid explosions? I have a second container where hydroxy rises in and to a tube. When i lit my torch which was a tube and a needle, it blew the lid off the jar.
Hello, great job, you are the best, Tell me, What voltage and amperage do you use?
What power supply are you using?
does baking soda is allow also to make the water become combustible instead of potassium hrdroxide??
So why did the metal plates turn yellow? What was that?
what preventiones are there for the flame to travel up the tube and ignite the hydrogen gas inside the device?
bubblers
I remember a long time ago that carsandwater talked about finally showing us the set up of his Hydrogen/Oxygen Generator so he could clean it.
i use sparkle toilet bowl cleaner, cleans that brown goop off fast
almost a kilowatt of power you might as well well with the electricity .however if you have enough solar panels to generate that much electricity?
where u buy the plastic fittings ??
hi, a question is why many neutral plates?
To achieve the 1.5 to 3v between plates which is the most efficient voltage range.
When both plates are in same container how hydrogen and oxygen are still in gas state when coming out
This (HIPER-VOLTIC-HHO) reactor can be serviced while running. Close lower valve remove lower reservoir empty AND replace. Open valve add (HV) premix to upper resivour, check again in 60 hours repeat if needed
what is HV ?
@@davelawson2564 HIPER voltic=purest balanced mixture of hydrogen 2 oxygen 1 that can be made on demand
@@michaelarcher9201 Obvious question . what is cost of power for generating 1 kg of this mixture ?
i wonder though, why does the flame not burn back to the bubbler? also what power supply is that?
and sometimes it does burn back to the bubbler, which is called a flashback.
Hi, i don't understand the part when the tube of water touchs the plates. In the video skip that step. Can you explain it to me, please?
I have a question how much gasket thickness
?
Hello Sir. Does this system that you made, DOES it SEPARATE the hydrogen and oxygen gases? In other words, the gases come out separately from the generator or do they separate on the plates but come out together through the same outlet? Thank you very much for your reply.
they come out together from the generator, but do not react with each other until they are lit by the flame
is that Astron VS-70M-AP power suply?if i have to use in my car wich power suply or power regulator(amp and volt regulator) will you recomend me?please give a link of a regulator for my car
just pull power from the car battery..
sometimes I think this channel could pass off as ASMR
👍🏼
You have your holes at same place so your plates can't create so much that way. It's better to have first plate 2-3 holes at the bottom and next plate 3 holes on left side, next 3 holes on right side etc until last plate where the exit is and have 3-4 holes at top to get best effect out of everything. I use 22 plates, size 150mm x 150mm and gives me plenty of HHO.
If run backwards, does it produce electricity?
Where did you purchase the nozzle at the end?
What's the thickness of the PVC liner do you use? I think I saw it. Its 40 mil pvc liner from Homedepot, great!
Excellently made and nicely videographed ! congrats !
What is in the tube going to the torch? Hydrogen or Hydrogen and Oxygen?
Both. They've gotta go somewhere.
since both the oxygen and the hydrogen outlet go into the water reservoir and hydrogen torches reach their insane high temperatures, I think it's both ^^
Hydrogen is the flamable gas.
Oxygen is the oxidiser, which allows the chemical reaction to happen.
Water is the biproduct.
So the flame can go right back in the tube until it reached the bubbler. That's pretty unsafe
Vector , It wouldnt do anything but cause a noice really. The preassure would be able to escape the tube before the tube breaks.
havent had to clean mine since I bought it 3 years ago.. thing is... the plates arent just normal stainless.. they're 316L grade stainless... which is the most resistant to grain boundary carbide precipitation.. aka the leaching of iron into you water..
I also use 9x distilled water so it has no mineral's or elements in it either. still looks like when I bought it.
what is 9x distilled water ? And how many hours have you run it ? what do you use the hho gas for ?
where can i find a complete parts list and instructions for this?
This video
i am not very good with this concept as this is my first time watching HHO stuff. what do the neutral plates do? 1 positive plate in the middle and 1 each negative plate at the ends and a bunch of neutral plates in the middle. i dont understand this setup. whats the purpose of the neutral plates between the + and - plates? thanks
Is the cell itself heating in normal usage? I wonder what is the efficiency of the cell..
If the PSU supplies for example 500W, is 400W transferred for heating the water and 100W for producing HHO?
mines running just luke warm 12volts at 7 amps... its a + N N N N N - rig
Hello.
Thats awesome!👍
Can i ask, why the neutral plates? Whats the purpose of these?.
Best regards,
T
That's a neat generator! How long can you run that generator for till you need to fill it up again? And do you know what temperature the generator operates at?
Wow very helpful! How much power do you supply through it?
next time bro try to focus on the camera the outcome gas results... i saw only water bubbling didn't saw the ouput gas... anyway so amazing bro you did and excellent job... I would like to ask you if i could convert this gas into cooking gas just like gas stove?
I think this is really cool! You definitely have my support
Beautiful video I like your project thank you for sharing
How efficient is this? How much Hydrogen vs watts used?
You get less energy than you put in. Not sure about exact numbers
and here i was thinking you get more energy than you put in, defying all laws of physics
+Ornf That's what I'm here for ;) Can't let you keep a false belief.
+Ornf But for real, there is also a possibility of yielding the same amount of energy. Satisfying the definition of efficient which was the original question. So I wanted to address the question to that extent.
I was just wondering since you can get 50 Liters of hydrogen for 30$. So it might be pointless to do this at home.