How To replace a Mazda CX-5 screen | No more GHOST touches | 2018

แชร์
ฝัง
  • เผยแพร่เมื่อ 22 ธ.ค. 2024

ความคิดเห็น • 59

  • @fattypros82
    @fattypros82 3 หลายเดือนก่อน +3

    Thanks for this, got it done on our 2017 in just under an hour. A few notes:
    - Mazda part no K1Y3-61-1JZA includes the plastic screen and a new plastic back, it retailed for about $180 US as of this date (9/15/23). All you need to do is transfer the PCB and metal shields.
    - I followed another comment's suggestion of blocking the vents and opening beneath the vents with some shop towels. It saved the radio bolt from falling which would have complicated things for sure!
    - The smallest ribbon cable's white line didn't line up fully with the PCB line , making me concerned when attaching that it wasn't in far enough, but it worked. The other 2 ribbon cable's lines matched.
    - It helps to carefully pull the centermost edge of trim for the gauge cluster out to get the radio back in, I had trouble lining up the guide peg on the left side until I did this. It will need to be pushed back in to get the top trim with vents back in place.
    - A trim removal tool set from Harbor Freight really helped. Even with flipping PCB tabs up. I highly recommend it.
    - I am going to add a screen protector as the old screen had the coating wear off over time from oils on fingers, definitely noticeable on common touch points. It's recommended to only clean the screen with a microfiber cloth.
    Thanks again for the great instructional video and I hope the new screen lasts for a long time! This should have been a recall though.

  • @jodismith82
    @jodismith82 8 หลายเดือนก่อน +10

    Dooood….. thank you for the vid! I bought a used 2018 cx-5 4 years ago, and had the dealer install car play. The ghost touch issues started about 2 years ago, and it was really bad when the car had been sitting in the sun. Never any issues in cold or darkness. Bought the same kit off Amazon that you had. No more ghost touch and everything is working flawlessly. A little scary but thanks to your video I had the confidence to tackle this!!!!

    • @Enila21
      @Enila21 6 หลายเดือนก่อน +1

      Would you have the link for the Amazon kit?

    • @jodismith82
      @jodismith82 6 หลายเดือนก่อน

      @@Enila21 www.amazon.com/gp/product/B0CMQB7LMF/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

    • @sivuyilebanzi602
      @sivuyilebanzi602 5 หลายเดือนก่อน

      Link please

  • @squrrll
    @squrrll 3 หลายเดือนก่อน +2

    I've already done the AA/Carplay upgrade in my cx5, but eagerly awaiting your video because they are quite entertaining. Your spark plug video was great, changed mine out in 10 minutes today!

  • @tmichaelhawkins
    @tmichaelhawkins 6 หลายเดือนก่อน +1

    Can NOT thank you enough. I replaced my daughter’s 2019 cx5 screen solely following your lead. You and your wife are the best!

    • @MaqsVids
      @MaqsVids  6 หลายเดือนก่อน +1

      Heck yeah!!! You are very welcome. I'm glad it helped.

  • @blackbunny9211
    @blackbunny9211 3 หลายเดือนก่อน +2

    Thank you! I was crying when this started to happen to my car. Knowing the prices to fix it 😭 thanks for the video! I couldn’t believe I did it!

    • @MaqsVids
      @MaqsVids  3 หลายเดือนก่อน

      @@blackbunny9211 Heck yeah!! One of the few flaws with these cars. 👍👍

  • @billganon3357
    @billganon3357 5 หลายเดือนก่อน

    absolutely spot on process from beginning to end. I had the exact same experience ordering what I thought was the whole screen housing and only getting the raw screen and metal box backing with the computer strip connectors. Your advice was perfect. Many, many thanks.

  • @VinnyVarious
    @VinnyVarious 9 หลายเดือนก่อน +1

    Look at team Mr. & Mrs. Marq Mazda do the thing!!! Nice job 👍🏿

    • @MaqsVids
      @MaqsVids  9 หลายเดือนก่อน

      🤔😁 I love it! I'm going to show my wife. Maybe she will want to work on other things. Thanks and have a good week

  • @JordanDBoyd
    @JordanDBoyd 3 หลายเดือนก่อน

    THANK YOU! This was so incredibly helpful. Very thorough. Took less than an hour!

  • @RaffiBoloyan
    @RaffiBoloyan 5 หลายเดือนก่อน +1

    super helpful walk thru. I was able to follow along and replace my screen no issues!! Thanks so much

    • @MaqsVids
      @MaqsVids  5 หลายเดือนก่อน

      @@RaffiBoloyan heck yeah!!! You are very welcome!

  • @jdub976
    @jdub976 5 หลายเดือนก่อน +1

    Thank you doing mine this weekend. Im not paying a dealer 1200 when I can just disconnect the touch feature. We never use it anyway. Appreciate the knowledge.

  • @Placeholder25
    @Placeholder25 4 วันที่ผ่านมา +2

    Where did you get that pry tool?

    • @MaqsVids
      @MaqsVids  3 วันที่ผ่านมา

      @@Placeholder25 I got mine at harbor freight many years ago. But, now Amazon has tons of options. I would get something like this today.
      amzn.to/3VMUgfD

  • @mikemontano9137
    @mikemontano9137 2 หลายเดือนก่อน

    Ok 1st off, thank you guys for making this video. The antireflective coating on the screen was ruined in my mom's 2019 CX5 due to being sprayed with detailing spray. I noticed how horrible the screen looked and she didn't know what to do so I am looking into doing the work for her and save her some money. 2nd you guys are awesome working together like that. Marriage life, doing work together and planning out dinner ideas, did i hear that right? Burritos with black beans and sweet potato stuffing lol.

  • @leohebert2766
    @leohebert2766 5 หลายเดือนก่อน

    Awesome! Your direction was spot on! Had the screen replaced in an hour. Thanks so much for a great video!

  • @The_Techie_Chef
    @The_Techie_Chef 9 หลายเดือนก่อน +3

    Great work! One tip for the next time you need to remove adhesive screen bezels is to use heat. For small, movable parts I like to use a small heating pad set to high and just set the area to be heated on it with a bit of weight over the top and let it sit for 10-15 minutes. It really softens the adhesive up so you can get in there with a spudger. If you're working on something bigger, a hair dryer works too but you need to take care to heat things evenly.

    • @MaqsVids
      @MaqsVids  9 หลายเดือนก่อน +1

      Thanks! That's a great tip. That's what I have done in the past on phones. I SHOULD have done it with this too. It would have been so much easier.

    • @The_Techie_Chef
      @The_Techie_Chef 9 หลายเดือนก่อน

      @@MaqsVids Yep! Definitely worth the trouble and the wait. I've taken apart a few MacBooks over the years replacing screens and back before they shrunk down the borders around the screens, they had a tendency to use adhesive around the monitor bezels. Terrible combo of visible, flexible, and fragile. Heat made it not so terrible to work on.

  • @briengakaplan-b1550
    @briengakaplan-b1550 12 วันที่ผ่านมา +2

    I’d have updated to the 10 inch screen that’s in the newer CX-5s while I was in there. But great job!

    • @MaqsVids
      @MaqsVids  11 วันที่ผ่านมา +1

      @@briengakaplan-b1550 Thanks and me too!!! 😉 But the wife didn't care. She drives the CX-5. So I just put the regular size in. 😏

  • @LuinnyAlejandoArmenta
    @LuinnyAlejandoArmenta 2 หลายเดือนก่อน

    Thank you! I did follow your video step by step and the new screen is working perfectly! Great video!

  • @celticwolf5352
    @celticwolf5352 6 หลายเดือนก่อน +1

    Thanks for this video watching this and digitizer alone replacement made me get full touch screen like you did. On 2017+ digitizer is too glued on and takes Lotta work. It's a $30 Part but lots of time removing and cleaning when $30 more you can get entire panel like in video. Ebay $75. Thanks for this saved me ton of time on digitizer removal and cleaning. I'd watched 2016 digitizer replacement and it's much less work (except bezel) so can get away with digitizer. But 2017+ your gonna be spending time! Not to mention touch sensitivity wont be as good not glued like factory. Best option (if you want to keep touch) is full panel like in this video!

  • @forbiddendonut
    @forbiddendonut 8 หลายเดือนก่อน +5

    I think I held my breath through the whole video. I always get nervous with removing trim because I always break just about every single tab.

    • @MaqsVids
      @MaqsVids  8 หลายเดือนก่อน

      You and me both. 😂Newer cars are a lot better but I never have that kind of luck with my older cars.

  • @TimDyb
    @TimDyb 3 หลายเดือนก่อน +1

    I've done this before. Easy to do. Go slow; take your time! I would caution you to put rags or paper towels in the a/c vent holes to prevent dropped screws/bolts from falling into them. Ask me how I know! 😁

  • @TheTruthSeeker756
    @TheTruthSeeker756 4 หลายเดือนก่อน +1

    Nice man thanks! I'm wondering if I should do it. I'll save $200. I don't want to screw up the dashboard though

  • @elai2049
    @elai2049 4 หลายเดือนก่อน

    Thank you for the video. I bought a new cx-5 in 2019. This just started happening 6 months ago. So annoying! :(

  • @Jan282000
    @Jan282000 9 หลายเดือนก่อน +1

    Thanks for creating this video. Do you happen to have a link and/or part number for the replacement screen?

    • @MaqsVids
      @MaqsVids  9 หลายเดือนก่อน +1

      Thanks. The link is below and I'll put it in the descriptionm. This is the one we ordered.
      ebay.us/HnClBE

  • @RAAUUULLLL4268
    @RAAUUULLLL4268 4 หลายเดือนก่อน

    Can you retro fit the 2023 10.25 inch screen to the 2019 screen?

  • @micahevans3443
    @micahevans3443 21 วันที่ผ่านมา

    Is there upgradable screrns i cant really find information on upgrading to bigger screen for the 2018 models

    • @briengakaplan-b1550
      @briengakaplan-b1550 12 วันที่ผ่านมา

      The dash and panels can’t fit the newer larger screens in the 17-20 models.

  • @piccolopilates4439
    @piccolopilates4439 6 หลายเดือนก่อน +1

    I have a 2020...the ghosting actions are getting worse AND the screen is a total mess. I've only used Windex on it but it looks like something is smeared all over it. I'd love to replace mine. I'm wondering if it would be the same on a 2020? Either way, great video and thank you for doing this. I heard that the Mazda dealership charges $1500 for this.

    • @MaqsVids
      @MaqsVids  6 หลายเดือนก่อน

      The process should be almost identical. But, I believe the later years have a larger screen. Whatever you do decide to do, good luck!

  • @sweetiemcgee
    @sweetiemcgee 6 หลายเดือนก่อน +1

    im curious why you didn't decide to upgrade to a more modern after market unit?

    • @MaqsVids
      @MaqsVids  6 หลายเดือนก่อน

      It's my wife's and she doesn't care. She just wanted the phantom touches to stop. I did get the module that allows carplay and Android auto though. I haven't been motivated to install it yet because she is perfectly happy with it the way it is. It was more a curiosity of mine.

    • @jy2789
      @jy2789 6 หลายเดือนก่อน

      @@MaqsVids Wired or wireless carplay? and which module allows carplay the new screen you installed or the usb hub upgrade?

  • @makojuicedaniel9307
    @makojuicedaniel9307 2 หลายเดือนก่อน

    Which ribbon cable is the digitizer, i dont want another one that can break on me and start ghosting i just want it disabled

  • @gordonq007
    @gordonq007 8 หลายเดือนก่อน

    nice video! However, I'd say the OEM screen looks better, since it doesn't have the silver rectangle when the screen is off vs the aftermarket one. OEM screen also has thicker glass cover as well. I've been trying to find replacement screens for my CX-5 as well, but it seems like they all have silver interior for the LCD (i.e. no OEM all after market) :(

  • @johnp1966
    @johnp1966 5 หลายเดือนก่อน +1

    id the replacement screen still working?

    • @MaqsVids
      @MaqsVids  5 หลายเดือนก่อน +1

      Yes it is. We've had zero issues since replacing it.

    • @johnp1966
      @johnp1966 5 หลายเดือนก่อน +1

      ​@@MaqsVidsawesome, thanks. I have to do the repair to my wife's cx5, it's driving her crazy lol.

  • @AaronSantry
    @AaronSantry 7 หลายเดือนก่อน +1

    I've done the replacement and now my Mazda says I don't have navigation. Did I make a mistake?

    • @MaqsVids
      @MaqsVids  7 หลายเดือนก่อน

      I wish I knew. Ours doesn't have navigation. I imagine a plug is disconnected. But I don't know what could cause that.

  • @JoeMayo1987
    @JoeMayo1987 8 หลายเดือนก่อน

    You don't happen to live near New Orleans, hugh? I need this done, but I don't feel confident I could do w/o breaking something. And I'm not exactly interested in forking over probably, $1,000 (?) to a mechanic.

  • @JstJensen
    @JstJensen 4 หลายเดือนก่อน +1

    You can replace the box in the center stowage bin and get apple carplay or android auto.

    • @MaqsVids
      @MaqsVids  4 หลายเดือนก่อน

      @@JstJensen YES!! That's what I wanted to do! But we have to upgrade the firmware in our system to accept. My wife didn't care to do it so we didn't include it. I'm excited for it too.

    • @JstJensen
      @JstJensen 4 หลายเดือนก่อน

      @@MaqsVids I have done it and it is well worth it! I just replaced our screen a few days ago as the OEM screen was getting harder to see with the 'pocking' that happens. (not sure exactly what to call it.) MAZDA will upgrade it for free if you take it to a dealership. The OEM Hub is easy to install.

    • @kyraeuswulf5091
      @kyraeuswulf5091 3 หลายเดือนก่อน

      Seriously, they'll do the upgrade for free?
      I actually purchased the kit already and have the hub that goes into the center console, but hadn't installed it yet because I was having the ghost touch issues (only I didn't mentally make the connection to it being the touchscreen, I just thought it was an electrical issue).
      Now I'm wondering maybe if I got a hold of the new touchscreen kit if they'd do both at once for a small charge or (hopefully?) free.

    • @JstJensen
      @JstJensen 3 หลายเดือนก่อน

      @@kyraeuswulf5091 sorry, to clarify they will update the software for free. They do not put in a new screen or center console hub for free

  • @eddyandrianasolo4799
    @eddyandrianasolo4799 9 หลายเดือนก่อน +1

    Nice car

  • @gibranp7966
    @gibranp7966 6 หลายเดือนก่อน +2

    Very disappointing that they make you do the adhesive nonsense at 8 minutes rather than just including the plastic bezel in the kit. Absurd.

    • @MaqsVids
      @MaqsVids  6 หลายเดือนก่อน +1

      I imagine you can buy the plastic bezel or find kits that include it. I wish I had paid more attention and found one myself.