Let me give you some words of advise. Get some sheet lead and line those jaws with the lead. Clamping down on those gears with steel jaws will ruin some gears. The lead will cushion the gear while holding it stable.
Open the chuck jaws. Remove the screw located in the centre. Fit a 3/8" (10mm) Allen key into the chuck and tighten with the chuck key. Smack the end of the Allen key with a hammer in an anti-clockwise direction and it will unscrew from the machine. Refitting is a reversal of this procedure. You do not have the split the drill body.
that method doesnt work with this particular model makita 6404 the shaft still spins in both directions when you put the allen key in it and there is no flat on the shaft for a spanner to hold it to smack it with a hammer. That model is about 40 years old.
I used th-cam.com/users/postUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K this for the first time today to replace the front wheel bearing on my rwd 98 dodge dakota. This had absolutely no issue removing or reinstalling the lug nuts and it took off the axle nut without any struggle. Sounds like it's got some muscle to it. Time will tell
Great Video! This is the only way to change the chuck if your drill spins too loosely to untighten the chuck the other way. The other way is tightening the chuck on a hex wrench and hitting it with a snap. My chuck was actually stuck in the open position so I couldn't tighten it on a hex wrench....this video saved my drill! Thanks.
The 'smack with a hammer' technique probably applies to older drills. I have a drill dating from about 2015 and wanted to remove the chuck. Unbeknown to me, there is a screw, left-hand threaded accessible with an Allen key placed into the fully open chuck. Old man with 'weak' hands that I am, trying to undo this screw as though it were normal RH, snapped said screw in two. Drill and driller are both fine but replacement LH screws are not that cheap or readily obtainable!
First and foremost, you don't really need to pull out the gears in order to change the chuck. Looking at the damage on the collet gears, it seems that you are a rough user. This is further demonstrated by the way you clamped the gears directly to the vise. I am not surprised that you will soon be changing another chuck in a very near future.
Desde colombia. Gracias por el video. Solo es que el tornillo que sujeta al mandril es rosca izqierda para que tomen nota y miren como gira el destornillador. Gracias vale.
Thanks for the video. If the video had been available many years ago I would have replaced the chuck on my old B&D. Replacement parts were more readily available and cheaper. These days the replacement chuck costs as much as a new drill so I would just toss the worn-out B&D and buy a new one.
You don't clamp gear on a vice Steel to steel .you can use Taflon or copper in between To avoid damage the gear. To replace chunk today is not Profitable as too many cheap Chinese drilling machine on the market
you have seen the hard way now i will tell you the easy way place drill in vise open chuck insert screw driver turn clockwise to remove the screw insert the key in chuck give it a good (WACK) counter clockwise now unscrew old chuck add new chuck install scew counter clockwise you are thru a 5 min job..
Да, да умник! В обязательном порядке НУЖНО! дрель разобрать! Ну хотя бы - правильно - винт с левой резьбой.ну а патрон с правой.А главное - я усвоил- дрель разбирать!!!!!!....
No need to takeout output spindle and gear assembly to remove the chuck. Allen key and a strike with a hammer would have done the work 🙁. I replaced the chuck of my skil 13mm drill by the above method.
Please dont try to hide your biggest mistakes, not taking any precautions and by damaging the main gear wheel by tightening in the vise.this is like penny wise pound foolish.😅
No need to remove the casing.put the key to the chuck and reverse use the hammer and you can remove the chuck.very simple only seconds to remove the chuck.
My B/D drill with attachments to fix I just have to put bit tighten key & give it slight blow from a hammer to remove the chuck to fit attachments, eg. saw, orbital sander etc. No need to remove any screws or open the body cover.
It looks like you cheeched the teeth on that gear by clamping it unprotected in your vice. I could see the damage when you removed it. You need to put some wood, leather, or something else between the vise jaws and your workpiece to prevent marring.
Thanks for your time, but I don't disassemble the drill to disassemble the chuck, I have a used key that enters and blocks the axis and then I unscrew the chuck
make sure the chuck is open like you are inserting a drill bit look in the back inside the chuck there is a screw that holds the chuck to keepit from unscrewing take it out clockwise
Um das zu machen, -also das Dreibackenfutter zu wechseln- benötige ich maximal 2 Minuten! Hätte er nicht so oft beim festziehen oder lösen in die verkehrte Richtung gedreht, so hätte er schon viel Zeit gewonnen. Er wird nie ein Handwerk ausüben -soll man lieber studieren- da kann er sich anders blamieren! Der Schreiber ist gute 85 Jahre alt und wwünscht noch viel Erfolg!
I have a 10 mm chuck fitted in my drill which I want to change to hold 13 mm Chuck which can be used for 13 mm bits. What I had to do for this conversion.?
remove the phillips head screw in side the chuck you need to turn it clockwise to remove it if you place the drill in a vice put a wrench on the chuck give the wrench a good lick counter clockwise t0 remove it once you break it loose it will unscrew by hand
DON’T do it like this! On every drill I’ve replaced the chuck on, you don’t have to disassemble it like this. Many other videos show easier way to do it and only takes about 15 minutes. Unless for some reason this particular brand requires disassembly.
Sir sira po angle grinder brand makita naupod po ung carbon nasagad q po nung palitan q ng carbon brush parang sinusunog nalang nia ano po dpat gawin dito tnx..po..
Sir thank u sa video mo natuto ako pano mg replace Ng drill chuck more bless sa channel mo sir..now I know...yes!!
Let me give you some words of advise.
Get some sheet lead and line those jaws with the lead. Clamping down on those gears with steel jaws will ruin some gears. The lead will cushion the gear while holding it stable.
Wood is also an option. Wooden plank.
Open the chuck jaws. Remove the screw located in the centre. Fit a 3/8" (10mm) Allen key into the chuck and tighten with the chuck key. Smack the end of the Allen key with a hammer in an anti-clockwise direction and it will unscrew from the machine. Refitting is a reversal of this procedure. You do not have the split the drill body.
that method doesnt work with this particular model makita 6404 the shaft still spins in both directions when you put the allen key in it and there is no flat on the shaft for a spanner to hold it to smack it with a hammer. That model is about 40 years old.
@@kenpoman1 You do not need to lock the spindle. The inertia will free the chuck eventually.
The END !! of the Allen ! Key ! ?? You Either ! Bend ! Or ; Break ! Or DAMAGE ! the Drill !.Doing that !!
@@davidwillard7334 - Ah, No.You've apparently changed a drill chuck or used a hex key.
21 21 56
Thank you very much, now I can easily replace mine🇿🇦
ကျေးဇူးတင်ပါတယ်ဆရာ.....နည်းလမ်းလေးဝေမျှပေးတာ
Very good information, thank you bro
I used th-cam.com/users/postUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K this for the first time today to replace the front wheel bearing on my rwd 98 dodge dakota. This had absolutely no issue removing or reinstalling the lug nuts and it took off the axle nut without any struggle. Sounds like it's got some muscle to it. Time will tell
kafi bidwan ho bhaisab aap..gear ko vice me tight kardiye bina packing k... naman aapko
Very helpful boss galing napalitan ko na chuck ko nabasag kasi ang bit kala ko may naiwan pang turnilyo big help talaga
Great Video!
This is the only way to change the chuck if your drill spins too loosely to untighten the chuck the other way. The other way is tightening the chuck on a hex wrench and hitting it with a snap. My chuck was actually stuck in the open position so I couldn't tighten it on a hex wrench....this video saved my drill!
Thanks.
What if it frozen to tighten position? I cannot loose it..
@@clarkstarks6767 ....have you tried PB Blaster and a pipe wrench to loosen it? that should loosen it to allow access to the center screw.
Sounds like ! YOU ! STUFFED !.! IT ! UP !! EVEN !! MORE !! NOW !!
Nice dahil sayo madamikang natutulongan mga carpenter
Thanks for video now I can replace my drill chuck
And Damage !. The! Gear ! Too !
Amigo creo que debiste colocar algo,entre las quijadas o mordazas de la prensa, algo así como unas tiras de madera, para no dañar el engrane.
Muy buena su observación yo también me di cuenta.👍
Good Job.
The 'smack with a hammer' technique probably applies to older drills. I have a drill dating from about 2015 and wanted to remove the chuck. Unbeknown to me, there is a screw, left-hand threaded accessible with an Allen key placed into the fully open chuck. Old man with 'weak' hands that I am, trying to undo this screw as though it were normal RH, snapped said screw in two. Drill and driller are both fine but replacement LH screws are not that cheap or readily obtainable!
First and foremost, you don't really need to pull out the gears in order to change the chuck.
Looking at the damage on the collet gears, it seems that you are a rough user. This is further demonstrated by the way you clamped the gears directly to the vise. I am not surprised that you will soon be changing another chuck in a very near future.
True 😂😂
I think putvthe gear below so that it does not demage
Desde colombia. Gracias por el video. Solo es que el tornillo que sujeta al mandril es rosca izqierda para que tomen nota y miren como gira el destornillador. Gracias vale.
Thanks it is good video but it can be replaced without opening the cover..
How to fix a rod will turn with key
Thank you po Sayo sir.maaayos Kona itong sira na electric drill na SI na Ang drill shop.
lol.that was easy.glad the gear didnt break when you lock on the vice.😅
Great job and good video if u move the music🙏👍🤣🇩🇰
Thanks for the video. If the video had been available many years ago I would have replaced the chuck on my old B&D. Replacement parts were more readily available and cheaper. These days the replacement chuck costs as much as a new drill so I would just toss the worn-out B&D and buy a new one.
And Still ! Have ! PROBLEMS ? With that ! Too !!
Thank you so much for sharing this video idol keep safe and stay healthy idol Godbless you always 🙏😍❣️
Good nagkaroon ako ng idea thanks
You don't clamp gear on a vice
Steel to steel .you can use
Taflon or copper in between
To avoid damage the gear.
To replace chunk today is not
Profitable as too many cheap
Chinese drilling machine on the market
Canal show de bóla dicas top mesmo parabéns amigo 💯👍👍🇧🇷
you have seen the hard way now i will tell you the easy way place drill in vise open chuck insert screw driver turn clockwise to remove the screw insert the key in chuck give it a good (WACK) counter clockwise now unscrew old chuck add new chuck install scew counter clockwise you are thru a 5 min job..
My drill dosent have a screw in the middle what do I do
Another STOPWATCH !! IDIOT !! HERE !!
NO SCREW INSIDE THESE CHUCKS
HAI GOOD AFTERNOON SUPER idea SUPER WORKING SUPER Replace Another THANKS 👍👍👍👌👌👌🌹🌹🌹
You replace the chuck but you damage the gear.
😂
Tama😂
Senseless way
Да, да умник! В обязательном порядке НУЖНО! дрель разобрать! Ну хотя бы - правильно - винт с левой резьбой.ну а патрон с правой.А главное - я усвоил- дрель разбирать!!!!!!....
Next time, place 2 chocks of wood between the Vice walls.
never seen it done like this before. There is a much easier way
Thanks for showing the long way to do this
You use vise to hold the thread?. It can damage the teeth
That is completely correct. When I change a tyre, I also drain the coolant first.
And Lost ! The Air ! Too !!
Wrong method... Between the steel wise plates, Gear will get damaged
He should have clamped it between two pieces of hardwood.
No need to takeout output spindle and gear assembly to remove the chuck. Allen key and a strike with a hammer would have done the work 🙁. I replaced the chuck of my skil 13mm drill by the above method.
Yes, you'r right to say.
Please dont try to hide your biggest mistakes, not taking any precautions and by damaging the main gear wheel by tightening in the vise.this is like penny wise pound foolish.😅
No need to remove the casing.put the key to the chuck and reverse use the hammer and you can remove the chuck.very simple only seconds to remove the chuck.
Not Such a Good ! IDEA ! With Pins ! In it !!
My B/D drill with attachments to fix I just have to put bit tighten key & give it slight blow from a hammer to remove the chuck to fit attachments, eg. saw, orbital sander etc. No need to remove any screws or open the body cover.
R u not damaging the teeth of the cog, by clamping it directly on a vic?
yes not damage teeth of gear
That's what I thaught too. Personally I would have used a woodworkers vice or one that has wooden grips on it.
nice bro maraming matulongan
It looks like you cheeched the teeth on that gear by clamping it unprotected in your vice. I could see the damage when you removed it. You need to put some wood, leather, or something else between the vise jaws and your workpiece to prevent marring.
Thanks for your time, but I don't disassemble the drill to disassemble the chuck, I have a used key that enters and blocks the axis and then I unscrew the chuck
THANK YOU FOR YOUR CLEAR VIDEO
Thank you, that helps me.
Good idea dear
Merci pour l’astuce . J’ai un problème pour changer le mandrin je ne sais pas comment m’y prendre.
Very nice 👍👍
Sir kapariho din ba ng black&decker yang nasa video nyo
unbelievable, unscrew the whole Drill to change the chuck; he did not need my friend
DE VALT ,10mm ഡ്രിൽ മെഷീൻ റെ ബോൾ ബെറിങ് കിട്ടുമോ നമ്പർ അറിയില്ല
i am learning thanks.
Yyyyyty
Sounds ! More ! Like !! STEALING !! THAN ! ! ANYTHING !! ELSE !!
Hvala na savjetu
Actually we can replace it without open the cover right? Anyone?
Yes. Maybe that's a really old drill and removing it is different. Modern drills you don't need to do that.
@@nitelite78 x
read the comments
Correct, there's a two flats to put an open ended spanner on.
Right, why does he have to dismantle the cover
Very nice video thank you sir very much.
Awesome instruction video 😎
Big mistake! Don’t use a vice on that gear! Now you will need to replace it!
you 're' right, it is a big mistake.
Usta o MANDRENI böylemi değiştiriyor aslında çok basittir
Maraming salamat sa kaalaman bro stay safe god bless.
For a 9 mins video he has taken 4 mins to adjust camera.
dapat may tela o basahan yung gear para hindi masira pre..
ILike 😻😻
💞💞💞
i believe you can do it without overhauling the device
make sure the chuck is open like you are inserting a drill bit look in the back inside the chuck there is a screw that holds the chuck to keepit from unscrewing take it out clockwise
taga saan kpo pwede po pagawa
@@mylinevaristo9073 dont speak your lang. sorry
@@frankdavidson9675 NO SCREW INSIDE THESE CHUCKS
Um das zu machen, -also das Dreibackenfutter zu wechseln- benötige ich maximal 2 Minuten! Hätte er nicht so oft beim festziehen oder lösen in die verkehrte Richtung gedreht, so hätte er schon viel Zeit gewonnen. Er wird nie ein Handwerk ausüben -soll man lieber studieren- da kann er sich anders blamieren!
Der Schreiber ist gute 85 Jahre alt und wwünscht noch viel Erfolg!
When do you chage a drill chuck ? Blund ?
I have a 10 mm chuck fitted in my drill which I want to change to hold 13 mm Chuck which can be used for 13 mm bits. What I had to do for this conversion.?
Oooo yes
Add drill sleeve in it and then fit the drill
Buy ! a New Drill !
Thank you for your post. I like this vd.
I would bet Noah was the previous owner of the vice.
Yong sakin boss mawigel na.. Papalitan narin yong ng ganyan?
Very good idea thanks
You do not take the chuck off by striping the dril 🤦🏼♂️
I don’t have a screw in the middle of my chick so what do I do
Why do you STRIPE ! YOUR DRILL CHUCK ! THEN !??
Vice the gear to open the chuck ??
Yes I was cringing to see the gear vised against steel jaws. He installed failure into the gearing of the drill motor~!
remove the phillips head screw in side the chuck you need to turn it clockwise to remove it if you place the drill in a vice put a wrench on the chuck give the wrench a good lick counter clockwise t0 remove it once you break it loose it will unscrew by hand
NO SCREW INSIDE THESE CHUCKS
Sir. TEK. MORE POWER UR. GOOD. CHANNEL,. THIS. VIDEO. MERON. SANA. AKONG TANONG. SA MUSIC. BACKGROUND MO WALA BA. SYANG COPY RIGHT.. SALAMAT SAGOT..
Can a Chuck drill be fitted on a hand grinder
You can Fit a Chuck on a Hand Drill !
maraming salamat boss godbless
Where can i buy this chuck drill.
Solo tienes que meter algo en el aspa para que no ae mueva y girar el trompo del lado contrarip de comongira y ae suelta y metes el.otro listo
Good 👍
next time DONT TAKE THE DRILL APART just remove the screw and undo the chuck a lot easer
Even if there are pins in it too !.
NO SCREW INSIDE THESE CHUCKS
the chuck may its good but the gear may cause damage at vise may cause crack
sapag kaka ipit mo sa gato maaaring madamage yung gear nya.
..tanong lang po sir kung pwde bang lagyan ng OIL ung gear para mas smooth yung andar..?..tnx..
Mas maganda cguro kong samahan mo ng instruction o magsalita ka para mas lalong maintindihan ng nanood
Looks like the vice (correct spelling!) is next in line for a makeover!
Like THE ! METAL ! SHREADDER !! AWAITS ! IT !!
Brilhante a essa eu vou aprender 😃👍
puoding maka ordir ng barina yan malaking bilog na gir
DON’T do it like this! On every drill I’ve replaced the chuck on, you don’t have to disassemble it like this. Many other videos show easier way to do it and only takes about 15 minutes. Unless for some reason this particular brand requires disassembly.
What is the brand name off the drilll?
Sato
PLANET! CHINA !! DRILL !!
Very good thanks you
It can be done unscrewing the machine.
What make is this drill anyone any ideas I've got one the same nut the lable is missing
How to flatten the teeth on the cog put it in a vice then tighten it up no need to take it apart anyway
Somebody should teach this guy. Clueless.
Should Have ! Just !! Put it in !.the METAL ! SHREADDER !! FIRST !!
Unsa man ang tong buhaton sa barena na wlay minor
Exelente video
He has to put some aluminum plate in the vise to protect gear tooth get damaged 😀😀😀😀
sir good day, saan nbibili yan tnx
Sa lazada
Where can i buy dewalt chuck
Makita store or powertools store or handy man store or lazada online or ace hardware
Dewaltrus. Sorry I couldn't resist that.
From DE WALT ! DISNEY !! STORES !!
Sir sira po angle grinder brand makita naupod po ung carbon nasagad q po nung palitan q ng carbon brush parang sinusunog nalang nia ano po dpat gawin dito tnx..po..
What is the price of Chuck?
£5
More ! Than! What ! The ! Drill ! Costs !!