Thank you very much , I used angle grinder to remove the chuck but I cut the round bar hitting it with hammer is a right think to do.hitting with hammer is a must and effective
I only replaced one on a portable drill and it had an Allen head cap screw down the inside bottom of the chuck. I had to loosen that first, then unscrewed the chuck. It pays to read the instructions that come with a new one. I also replaced a drill press chuck, but that was Morse taper.
To change a drill chuck , usually you turn it anticlockwise towards you, then you put its key in the chuck and tap it a bit hard with a mallet. That should loosen it.
this is the correct way to remove a chuck take the drill bit out look down inside chuck you see a screw turn it clockwise to removeit the turn chuck counter clock wise to remove it do not use a hammer
Some electric- drills use the system of putting the key in the chuck opening the jaws fully and tapping a bit hard with a mallet on the key to un-loosen the chuck. There are other ways of removing the chuck.
This kind of machine should not be used rough and tough and rather to be repaired or change of parts carefully as far as possible delicately. The inner parts may be damaged.
It is very simple to change the chuck into the drill, open widely the chuck to see the inner center screw loosen the screw to counter clockwise if the srew is very tighten apply a liitle bit force so you can easily unscrew... you don't need a hammer
Ese kon drill chuck change karta he bhai, drill chuck ke andar ka screw clockwise ghumakar khol lo agar screw ka head bit ki wajay se kharab ho gaya hai toh v koi problem nahi, drill chuck ke pass me ek spanner laganeka jagay rehta he usme ek spanner fasake fir drill chuck ko pipe wrench ki madat se pressure se anticlockwise ghumao easily open ho jayega ! Simple. Hammer marnese toh machine kharab ho jayega ??
All the drill chucks i ever replaced had a screw holding it on and then threads, but what do I know get a hammer and beat the hell out of it 🤔 shows you how dumb i am
My dear this procedure is wrong. Keep a 1" to 2" length screw or rod in one of the three holes of chuck and beet on it by 🔨 in tangential way ,anticlock wise direction.
Creo que al señor que está cambiando el mandril, lo están necesitando para sacarle un mugre del ojo a un paciente Se que lo va a lograr, lo que me aterra es cómo lo haría.
Ma non è un po troppo distruttivo cosi a martellate ?e poi é dicuro che non si deforma l'indotto ,ci credo poco cosi...vi è un'altro modo quello di svitarlo delicatamente.
Yo he cambiado varios mandriles de taladro, con un solo golpe aplicado correctamente sin maltratar el taladro y sin destruir el que vas a cambiar, para mi gusto y humilde opinión esta que presentan es una mala idea
A great You tube piece on what NOT to do to remove a Chuck..and damage the Drill to boot !...
For the cave man viewer
@@felixyoghurt3291😂
Lesson learned, If you don't understand how something works, just bang on it with a hammer until it gives up on working again🤣🤣
Rytt😂😂
Iyo yo
Film powinien mieć tytuł 'jestem idiotą'.
इसलिए,अंग्रेजों ने इसका नाम hammer machine रखा।।😂 ⚒️
Centre of chuck internally you use a cross head screwdriver and unscrew the lock bolt. Then turn chuck anti clockwise to unscrew.
والله حرام عليك
❤😢😢😮❤❤
Amigo, você está certo! Está é a melhor maneira para trocar um mandril!!! 😊
@@abdelrhaimmahir5291 :))
Best way to change chuck I have ever seen so far
To me that's the hardest way, plus drill can damage
That was one of the unknown application of hammer! Nice job broooo👍🏻👍🏻👌👌
i like your safety shoes my friend.
Very Good hafeez Bhai nice video 👍
Thank you very much , I used angle grinder to remove the chuck but I cut the round bar hitting it with hammer is a right think to do.hitting with hammer is a must and effective
Good job and nice tip on how to damage a power drill and get a new one
😂😂😂
This guy is actually crazy
Can I replace drill chuck without hammering?
Bhaijaan very good video very good information video Allah Pak aap karo bar aur aapki channel mein Barkat ata Farma👍👍👍👍👍👍👍👍👍👍👍👍👍
Very nice message
I only replaced one on a portable drill and it had an Allen head cap screw down the inside bottom of the chuck. I had to loosen that first, then unscrewed the chuck. It pays to read the instructions that come with a new one.
I also replaced a drill press chuck, but that was Morse taper.
To change a drill chuck , usually you turn it anticlockwise towards you, then you put its key in the chuck and tap it a bit hard with a mallet. That should loosen it.
Yes. That's the simple way to replace
The chuck , and it doesn't take much time.
Ini solusinya
Ini solusinya
th-cam.com/video/IOCpHIi48OM/w-d-xo.html
@@aasageer ya bro
Sinceramente fue el mejor video que me ayudo...😃
this is the correct way to remove a chuck take the drill bit out look down inside chuck you see a screw turn it clockwise to removeit the turn chuck counter clock wise to remove it do not use a hammer
Ależ gdzie tam.
Najpierw należy walić młotkiem.
Thanks a lot fot this great videk
Would you please advise me,
how many millimeter is the inner thread size of the 10mm drill chuck.
Thanks in advance.
Some electric- drills use the system of putting the key in the chuck opening the jaws fully and tapping a bit hard with a mallet on the key to un-loosen the chuck. There are other ways of removing the chuck.
2 million saw this very informative videos..keep it up..we learned a lot..
Best way of how to NOT change the chuck 😂
Very good 👍❤️❤️
Worked hard 👍
I have no words to describe it.
Sometimes thinking is necessary before going full Thor mode.
😂
I had a good laugh, thank you.
Si abres el mandril al máximo encontrarás un tornillo alen rosca isquierda solo tienes que sostener la llave y accionar la máquina sale en un instante
Cómo hacer las cosas mal un vídeo de un inútil tratando de mostrar lo que no se debe hacer
@@mariomoyano692 exacto a marraso saca el mandril con la herramienta de presicion jajaja a masaso limpio
Thank you very much.❤
Thanks for sharing how to get a new drill
the best and easiest way to remove the old head , i recommend it for every one , thanks
Magnífico.....!
Asumo que el Sr. de la foto es el autor de la técnica de vanguardia para cambiar el mecanismo de lo que quedó del pobre taladro.
Una bestia.
Itu namanya merusak didalam chuk ada bolt tapi melepasnya justru searah jarum jam, langsung lepas broew
I like videobyou sir😄😄🙏
Using hammer no good the impact can damage inside if you play video make it good work so that everyone understand improve your knowledge thank you
No así nose hace eres mexicano lo digo por huaraches piteados
This kind of machine should not be used rough and tough and rather to be repaired or change of parts carefully as far as possible delicately. The inner parts may be damaged.
How to destroy your drill for hammer lovers.
B
5
H78
😁😁😁😁😁😁
Ini solusinya
th-cam.com/video/IOCpHIi48OM/w-d-xo.html
Good video 🎉🎉
Good job.....done like n subscribe
Usse vi ak asan tarika hai!
It is very simple to change the chuck into the drill, open widely the chuck to see the inner center screw loosen the screw to counter clockwise if the srew is very tighten apply a liitle bit force so you can easily unscrew... you don't need a hammer
Solo tienes que calentarlo y sale rápido y entero sin daño alguno para utilizarlo de nuevo en otro taladro.
С торца вала при раздвинутых держателях сверла ставиться винт с левой резьбой!
Так ведь чувак не ищет лёгких путей... 🥴🥴🥴
@@ГеННадийГлодя 😁😁👍👍
This is pattan bay 😄😄😄😄
Thanks Bhai for this information
He's just doing it the unorthodox way 😂😂
That man is crazy😂i bet when he changes his pants he tears them off and remove the pieces😂
How to change drill chuck❌
How to destroy your drilling machine ✅
Good hit🇮🇳 👍👍 Kuki
Cara ini berhasil sy praktekkan
Pake kunci L bos di masukin ke bor lalu di ketok
I THOUGHT THIS IS THE CHANNEL OF HOW TO BASIC, I AM BASICALLY WAITING FOR THE EGGS TO BE THROWN OUT 😂😂😂
LOL 😅
pro trick: watch movies on Flixzone. Been using it for watching lots of of movies during the lockdown.
@Keegan Garrett yea, been watching on flixzone for months myself :)
Thanks. 👍
Watch on youtube, you’ll find good videos on how to change a chuck on your drill.
Jak udało Ci się nakręcić film, skoro taka prosta czynność zajęła Ci tyle czasu? :-)
Who knew that just beating the shit out of it could be so effective 🤦🏽
It can unbalance the saft
उसके बाद ड्रिल बिट डान्स करेगी 😅
😂😂😂😂😂😂 sahi baat hai bhai
السلام عليكم و رحمة الله تعالى و بركاته
عمل ممتاز .
I would be wearing some steel cap boots if i was him 😊😂
Bagaimana cara merusak presisi sebuah chuck bor? Ikuti video ini
title should be,how to remove and replace a chuck NEANDERTHAL STYLE...
Wow great job
You will damage the machine by using a hammer that is not the proper way to do it.
Can someone teach this guy to how to use screwdrivers?
Tem um parafuso dentro do mandril philips rosca esquerda a ser retrado e recolocado
Gracias 🙏
Hahaha excellent engineering
I do the same to change the whisks on my wife's Kenwood mixer, I'll get it right one day
Desde la ciudad de Mexico muy bien si me lo platican no lo creo mucha practica. Intentaré ese método graciad
Wrong solution, armature may be damage
Asta que no se dio cuenta que tienen un tornillo por adentro 😂😂😂😂😂 2:11
blunder.... a use of hammer on shaft
don't fallow this'll damage the drill
App kahan ke ho
Por dónde coloca la broca tiene un tornillo
O yar is mai threads th to hit q kr rh th hammer se?
Kis jagah ko Gaadha hai es mechanic.
Ese kon drill chuck change karta he bhai, drill chuck ke andar ka screw clockwise ghumakar khol lo agar screw ka head bit ki wajay se kharab ho gaya hai toh v koi problem nahi, drill chuck ke pass me ek spanner laganeka jagay rehta he usme ek spanner fasake fir drill chuck ko pipe wrench ki madat se pressure se anticlockwise ghumao easily open ho jayega ! Simple. Hammer marnese toh machine kharab ho jayega ??
well that's probably the most fun way, ... or perhaps a way of telling the drill you are annoyed with it.
I hope it was his own drill.
Boss saan ba ang location ng shop mo
నీలాంటోళ్ళందరూ యూట్యూబులో నేర్పించేయటానికొస్తున్నారు. అంతేలే జనాలు ఖాళీగా ఉన్నారు, యూట్యూబు తేరగాఉంది. కానీండి. మరిన్ని వీడియోలు రుద్దండి జనంమీద.
Waat laga dala puri drill machine ki😂🤣😂😂😂
La necesidad de los Paquistaní e Indues .abrazos
Just put the key in the chuck and hit it with a hammer anti clock wise
Veryyyy.... Goodddd........ bwaaaaaahahahaaaa
Why do you need a drill? A hammer fixes everything
You noob
He is a hard working guy you may watch his other videos of saving nature and environment.
😀si es cierto
Başarılar
Did anyone notice the electric cord going to this drill??
All the drill chucks i ever replaced had a screw holding it on and then threads, but what do I know get a hammer and beat the hell out of it 🤔 shows you how dumb i am
This is "How NOT to change drill chuck".
My dear this procedure is wrong. Keep a 1" to 2" length screw or rod in one of the three holes of chuck and beet on it by 🔨 in tangential way ,anticlock wise direction.
ধন্যবাদ
After watching this I have a headache. I'm going to fix it with a hammer too. LOL LOL LOL ...........
Banging it hard with hammer might destroy the shaft of the motor!
How to kill a drill 101
I love your comment, Bro 😃
Is ka andar chack main screw laga hota ha
Remove your contraceptive the same way.
Creo que al señor que está cambiando el mandril, lo están necesitando para sacarle un mugre del ojo a un paciente
Se que lo va a lograr, lo que me aterra es cómo lo haría.
Ma non è un po troppo distruttivo cosi a martellate ?e poi é dicuro che non si deforma l'indotto ,ci credo poco cosi...vi è un'altro modo quello di svitarlo delicatamente.
Yo he cambiado varios mandriles de taladro, con un solo golpe aplicado correctamente sin maltratar el taladro y sin destruir el que vas a cambiar, para mi gusto y humilde opinión esta que presentan es una mala idea
Рискует отколоть ось редуктора, лежит с таким дефектом
very good, amazing
What is the good brother ,this is wrong with humer
Tem.um.jeito.muito.mais.fasil..Com. Uma. Fraquinho. Na.onde.voce.bateu.tira.um.pafuso.tira.o.mandril.sem.abri.a.maqna
He forgot to put screw holder. It will hit definitely in his head 😀
*When all you have is a hammer, all problems are treated like nails*