In this video I go over my final Transmission build and a successful run. We ran the T-maxx for a good 15-20 minutes HARD with NO issues!! Thing's a Beast! Thanks for watching, Hope you all enjoyed!
Just got done doing same after the fact watched a video. I think your right alot of people over think it ez 2 just do. Gets rid of a lot of junk all that rotating mass gone. Simpler then rebuilding or parting 2gether a oem job 4 sure
Great job man hope its still running i watched your entire serries through the build ans finally got mine together today I'm running a 6s 180amp esc and 2150 kv motor this things literlly rips never had a rc car like it thanks for being the only video that helped me figure this out
Thanks for this comment! I really appreciate the support and kindness. I'm extremely happy that this helped you with your project! That was the whole point of me doing this series and trying my best to explain the process I took.
This is what I'm wanting to do to my T-Maxx, but with its grey gearbox. I bought the "single speed" and "forward only" kits, but they don't fit... I've since learnt there's a different one for the grey gearbox. Glad it's worked out for you!
nice video 👍 glad it's up and running as long as the mesh has a litte play should be fine will sound funny at first because of the metal to metal gears but it has some torque I like the setup
Rc Fun thanks man! Yea the mess does have a little play in it. It does sound a bit funny! LOL... I just don't want to jack up the pinion or spur gear... I don't have any replacements on hand and they cost a bit more than plastic lol.
Hey I'll go ahead and buy that conversion kit from you if you still have it 😅I was following your steps on the video until I came across the fact that you said that black transmissions are for that conversion and yeah
What "plate" were you talking about needing to get to use the single speed shaft because it lacks the role pin hole. I too have installed that gearset and would like to mount a sour gear. Thank ya sir!
Solved. After looking at the old style and new style input shafts I realized that the shaft diameters and location of the gear locating pins was the same, so I removed the pins and swapped the correct gear on the updated slipper shaft. I never found a "plate" for this though. Hope this helps.... Matt
Ebay, Amazon, walmart website it runs around $40. Not the greatest but it works...on side note it's not 100% waterproof, i found more than one person that had issues with the esc after it got wet but otherwise it does the trick. Good luck!!
I am converting my t-maxx to electric. I followed your tranny instructions but am totally lost on what you did to the spur gear. My transmission looks just like the original 1 from the outside. It looks like a giant slipper clutch? Also, what did you do for the brakes/ reverse?
@@joshuadulaney5559 I have since gotten a 3s Typhon n had a crazy 2650kv motor off this car and a 6s esc but I used to run it on 3s mostly but went 6s for speed runs n completely blew up both diffs
![[Live] : ONE 168 วันนี้!! "โจนาธาน vs ซุปเปอร์เล็ก"](http://i.ytimg.com/vi/0jIN65KgJsI/mqdefault.jpg)
Just got done doing same after the fact watched a video. I think your right alot of people over think it ez 2 just do. Gets rid of a lot of junk all that rotating mass gone. Simpler then rebuilding or parting 2gether a oem job 4 sure
Great job man hope its still running i watched your entire serries through the build ans finally got mine together today I'm running a 6s 180amp esc and 2150 kv motor this things literlly rips never had a rc car like it thanks for being the only video that helped me figure this out
Thanks for this comment! I really appreciate the support and kindness. I'm extremely happy that this helped you with your project! That was the whole point of me doing this series and trying my best to explain the process I took.
This is what I'm wanting to do to my T-Maxx, but with its grey gearbox. I bought the "single speed" and "forward only" kits, but they don't fit... I've since learnt there's a different one for the grey gearbox. Glad it's worked out for you!
nice video 👍 glad it's up and running as long as the mesh has a litte play should be fine will sound funny at first because of the metal to metal gears but it has some torque I like the setup
Rc Fun thanks man! Yea the mess does have a little play in it. It does sound a bit funny! LOL... I just don't want to jack up the pinion or spur gear... I don't have any replacements on hand and they cost a bit more than plastic lol.
its definitely to tight just back it off just a little I had the same issue if you feel the gear after driving it will super hot.
Nice video
Thanks Extreme RC!
Taller tires would give you more top end speed increase. also what if you did a gear change ?
Hey I'll go ahead and buy that conversion kit from you if you still have it 😅I was following your steps on the video until I came across the fact that you said that black transmissions are for that conversion and yeah
What "plate" were you talking about needing to get to use the single speed shaft because it lacks the role pin hole. I too have installed that gearset and would like to mount a sour gear. Thank ya sir!
Justin, I'm having the same problem. Did you ever figure this out?
Solved.
After looking at the old style and new style input shafts I realized that the shaft diameters and location of the gear locating pins was the same, so I removed the pins and swapped the correct gear on the updated slipper shaft. I never found a "plate" for this though.
Hope this helps....
Matt
Exactly
Ty 4 the video!
Got a question!
What can happend if I use the 2 speed transmission?
Why dump all the gears when you can just do the forward only mod and have a two speed transmission... Having that second gear is a huge advantage.
Cause the way rev works electic motor reverses direction trans would just b n neatral
I can't do forward only I'm okay will all that I like to reverse my trucks lol
There is now a bracket to mount an emaxx tranny into your tmaxx. Solves everything
ben dover how much is emaxx trans sell for?
man that turned out great. what did you use for reciver transmitter ?
T.Man thanks for stopping by. I am just using the stock Transmitter and Receiver from Traxxas that came with the T-maxx.
hello do you know where I can find this conversion kit? I'm looking forward to buying one for my T Maxx.
Ebay, Amazon, walmart website it runs around $40. Not the greatest but it works...on side note it's not 100% waterproof, i found more than one person that had issues with the esc after it got wet but otherwise it does the trick.
Good luck!!
can you tell me the gool rc motor and esc combo you put In the truck please
I am converting my t-maxx to electric. I followed your tranny instructions but am totally lost on what you did to the spur gear. My transmission looks just like the original 1 from the outside. It looks like a giant slipper clutch? Also, what did you do for the brakes/ reverse?
Brakes get ditched esc takes care of it. Just use revo input shaft go slipper delete metal gear trust me
How does the black transmission work on the 3.3 because the drive shafts are bigger
Hello good day! In the transmission box did you just use the three gears to convert?
Yes, just three gears! Was very simple and easy once I was able to simplify it!
I saw the video was great the result with the T Maxx! mine to convert is a 2.5!
it gets to a point where just leave it all original sell on ebay and by a Kraton or Revo.
Where did you get the motor mount please?
What did you use for the motor mount? Thanks!
I used the motor mount from How2RC.com. Thanks for the question!
what do you mean when you go reverse the tires turn ?
I think you could easily gear up. get a smaller spur gear. you have plenty of torque to spare. smaller spur would give more top end speed.
Hey what plate would you need?
Please help how can i use the single speed with the slipper upgrade it doesn't fit
Knock pin off use gear on any say revo input shaft and slipper delete
@@joshuadulaney5559 I have since gotten a 3s Typhon n had a crazy 2650kv motor off this car and a 6s esc but I used to run it on 3s mostly but went 6s for speed runs n completely blew up both diffs
HELLO I VOUDROI CONVERT MY T MAXX ALSO CAN GIVE YOU THE LINK OF THE PIECE
To tight
2 layers of paper works well