waste oil burner for scrapping construction and first fire up
ฝัง
- เผยแพร่เมื่อ 1 ก.ค. 2014
- LOTS OF OTHER BURNER VIDS ON MY CHANNEL!! DIY Waste Oil Burner for high power heating and Melting for scrapping. Build demonstration and first firing up to show running.** Before bitching about a bit of smoke on this first TEST run, PLEASE look at the other vids on my channel of this burner Running perfectly CLEAN before making stupid environmental green washed comments. ** UPDATE: • Waste oil Burner High ...
Waste oil burner designed for melting scrap aluminium and maybe copper as well as foundary use. The burner will run on any waste oil including used engine oil, waste vegetable oil, transmission fluid or even liquid lard. The oil burner was built from an old fire extinguisher bottle and some car exhaust pieces. The only measurements taken were that of the exhaust pipe which is 50MM. The positioning of the inlet and outlet was simply eyeballed.
As can be seen by the paint burning off, the waste oil burner was built and then fired up successfully from the very first lighting. To preheat, a piece of old oily rag is used. This wicks up the oil in the bottom of the burner and pre heats the oil to vaporise and burn.
With a stronger blower and without excessive oil in the burner when lit, startup will normally be much quicker and output far stronger.
The blower is from a car and was very underpowered for the potential of this burner. The pulsing flame on startup is due to the weak air supply and when Filming the vid I forgot to turn the oil off so upon lighting had a large pool in the bottom. As can be seen later in the Vid, once the excess oil has burned off the flame is steady. The excess smoke is a factor of the weak air supply not mixing correctly with the vaporised oil. With the right strength blower combustion will be totally clean.
With a strong air supply I expect the potential output of this burner to exceede 200 Kw and maybe over 300KW, depending on the strength of the air source used.
The downward firing is to facilitate the melting of small pieces of scrap aluminium parts and to seperate these from steel components with a minimum of labour.
Fuel regulation was simply with a 1/4" ball valve. The waste engine oil used was very thick and not quite flowing quick enough to keep up with the demands of the burner even at the low air supply.
The test was successful however in that the burner fired up easily even with nearly every less than ideal factor against it and ran well given the low air supply. I expect it to be a very different beast when fed sufficent Oxygen. - วิทยาศาสตร์และเทคโนโลยี
I have a lot of really great and supportive regular viewers on my channel that understand what these things are about and have the intelligence to look after their own well being and personal responsibility.
For some reason though, this particular vid seems to bring out every whining safety sissy crybaby and environmental zealot who can't be bothered to read the description or info here but rush to post ignorant and foolish comments.
It's got to be really old so from now on, comments which are just put up for the sake of having a sook about something already explained or just to grandstand will be deleted.
People with genuine interest are most welcome to post questions on this or any of my other vids and I will do my best to answer them and help people build the different styles of burners I have made as I always have tried to do.
how do you get the oil in the burner
+Oil Burner Just found this video via a TH-cam "suggestion" so apologies if I appear oblivious to your story. I haven't read the posts in question but all I can say is just ignore the "haters". For some reason TH-cam comments seem to be some of the most hateful and argumentative on the internet. Just carry on doing what you do and rest assured that there are thousands of viewers who enjoy your work and don't say a word.
There's a video on my channel from >10 years ago which shows what my friends and I used to do with waste oil. Little regard for health, safety and the environment. I welcome any highly vocal and angry criticism.
+Andy Elkins Disclaimer: I've only just watched this video so I may be wrong. At around 5:55 he opens a valve which delivers oil (gravity fed) through a PVC pipe connected to a 1/4" copper pipe into the burner.
igotes
Thanks mate, Much appreciated.
I thought it was Christmas, Must be saftey Zealot season again?
In any case, Merry Christmas to all my regular Viewers and thank you for your support. It's much appreciated to get useful feedback and know you are enjoying my Vids. I
Hope Santa brings you all exactly what you want and you all have a prosperous, Healthy and enjoyable new year ahead.
*****
Why ask at all? Is is such a terrible thing to allow me to take responsibility for my own well being and make my own choices?
Do I come across as such an idiot or so inexperienced as you don't think I know what I'm doing and the inherent dangers?
I don't tell other people not to wear whatever they want, why do the safety whingers all feel the need to force their ways on me?
I really wonder how many people that crap on about what I'm doing without gloves etc have actually used this sort of thing themselves and have any experience in what they are talking about. It's pretty clear that most haven't but are merely repeating what they heard some expert say so as to look knowledgeable and take the moral High ground.
Anyway, check out my latest Vids. I put a safety warning on every vid now!
*****
I believe that 99% of the people that whine about safety do it in fact because of purely selfish reasons in that they want to be seen to be knowlegeable when they in fact know nothing about what they are seeing or have any idea of the real risks through complete lack of experience.
Getting a burnt finger isn't going to Kill me and it's nothing worse than hitting onself on the thumb with a hammer.
I think many of the safety zealots are idiots because they go on about things which aren't a risk at all, Like wearing a mask which I always do, not for safety but because of self presevation. They also go on about bleedingly obvious things That anyone could clearly see and never mention things which a person may miss like I tried to do with my Veg oil danger Vid.
So far ALL the real dangers I have Identified in doing these Vids and using these burners are hidden things No one has yet warned me about which makes all the safety comments basicaly useless.
Glad you like the Vids and I'll endeavour to keep doing them whilever people are interested and entertained by them. :0)
Stanlee O'Tool
I think you are spot on. So many times it's patently clear these people are incapeable of any hands on fabrication themselves and almost without exception, never have anything they have done themselves on their account.
Not everyone has the facilitys to do things but as you say if you don't have the knowledge or experience, just shut up and watch or go somewhere else. Don't try and make yourself out to be knowledgeable in something you are not.
Stanlee O'Tool
I know exactly what you mean! I have seen so many products and machines that I didn't even know existed because they aren't used in my part of the world. And that's commercial things, let alone what people come up with and make themselves. Then there is the thing of if you have a problem or want to fix something, there are usualy quite a few vids on how to do it.
There is a lot of crap on here but it's outweighed by the tons of useful and entertaining material!
the only thing that i worry about is the kid that watches and says well doing this or that seems to be just fine practice.
so no its not just effecting you. i dont typically tell anything about safety. but youtube reaches so many people. you are bound to cause someone harm other than yourself
i seldom where gloves.... but i know what im doing and dont put out videos
just a thought
Oil Burner: Forget the negative comments. I’m here to learn. Great job.
Yesterday TH-cam recommends a video on a homemade sandblaster. Needed it. Made it. Today this. Needing it. Making it. All of the sudden TH-cam cares about what I need. My heart is touched. And I love this thing. Can't wait to find a use for the heat I can make with all my old motor oil.
Made one like this from an old air compressor tank and blower off of an old kids bouncy castle, Worked great to melt old water pumps, lawnmower engines etc. Did not smoke either. I burned used motor oil.
That is some crazy flames poring out of that thing. Nice job!
It sounds like steam engine when the oil burner is running.
Sounds like an old school locomotive! :) Nicely done!
Watching that thing burn is so soothing. It's like popping bubble wrap.
Your comment made me laugh :-)
Awesome... I love this little unit... as well... Oil Burner... I love the power thats coming out of that thing... Just fantastic.. thanks for sharing...
Thanks for your interest in it. It's very rewarding to get positive feedback. I do love the the sensation of power that these things produce myself. I'm going to be working on more designs both more and less powerful to suit different applications.
For melting aluminum it should be great!
The reducing oily flame should help prevent the oxidation of the aluminum into aluminum oxide and give more pure aluminum
Got inspired and built one from a 4.5 kg gas bottle, works a treat once I got it going. had issues getting it to get hot but watching this I see I need a fair bit of fuel/rag to start then plenty of oil and whooee much fun to be had.
The start up is what most people have problems with. many get a good fire going then have a freak out and then kill it just when the thing starts getting up to speed. once you get a feel for them though it's very easy.
The key to them is heat and plenty of it.
Thanks for all your videos I enjoy watching them. I mainly want to know about this type of stuff because I would like to make a forge for melting metals. Thanks for your time you take to show us how this is done.
Bellissimo! Mi aspettavo che ad un certo punto si sciogliesse il secchio, tanta era la potenza e la temperatura della fiamma!!
You just nailed the welding safety basics.
true but nailing assholes sound a bit gay ;)
Our government is so severely, badly educating us! Thank you for showing us the massive power in a WASTE product!!!
I think it's a great project and simple design! perfect for a little foundry or such. well done!
That whole thing went from painted to completely oxidized in 20 minutes... Wow.
what is the blower, not sure what to use
John Jones I think it's the air breather or how you call that of a car
Going to add this to my bucket list. Looks like it was working very smooth for a first run. looks like this could also be used to heat water for a closed loop steam turbine for an off grid power generator. nice project.
Thanks mate. Have a look at my other visd. I use the same types of burner to heat water in a converted gas heater and many other things along those same lines.
Love it!!!! You just demonstrated a $1000000 DIY Project right there. Gave me some good ideas.
Thank you so much for inducing the evolution of an idea I am building a proof of concept for.
Seriously; Thank you.
geez louise, all the safety comments are absolutely ridiculous. those crying about lack of them, how bout this, the tools needed to make this stuff come with instructions and warnings.They are sticker-ed and labeled all over the place. if you dumb enough to burn a hole in your shoe and have a ball of molten steel burn the crap out of your foot, then there's your warning. they don't need to be gone over as a preemptive strike to save some idiot from hurting himself. Damn, it goes without saying, this is dangerous stuff. don't waste my time with all that BS. I hate it when I watch a video and some ass that is in love with the sound of his own voices goes on and on about PPE like he's General freaking electric himself. Damn, let them man make his show and it not be about the obvious and you go back to paying your union dues.
Well said! You would think this vid was about building a Nuke reactor in your own back yard the way some saftey sissys go on.
I'm pretty much at the point of just removing the stupid safety comments From now on. They are not helpful and if some moron needs to be told to wear gloves or other obvious things then they have no business even looking at these vids with a thought of building, let alone using one themselves. The saftey zealot warnings are aimed at people that would never think to get their hands dirty making something themselves so therefore are pointless anyway. If they are here for entertainment value only, then again they are pointless.
The people that do things themselves are here to learn things beyond puting on gloves or eye protection.
They have already well and truly passed that level.
I just love all your videos oil burner.........I live in northern Canada and I still play with all the designs that you've made/built and its -30 degrees celcius here atm.............I don't know why ppl have trouble firing up their burners......I always seems to be able to fire mine up..................I recently built a foundry and I used ur simple spray burner with just a Cpl fittings and damn I tell ya......that thing gets hot.............I was able to melt steel in my furnace.....and ive melted down about 300 pounds of copper so far and about 600 pounds of aluminum...................my last run I used a 1/2 inch thick steel crucible using an 8 inch diameter pipe..................and I did not notice soon enough that I clearly melted one whole side of it.........................I really really enjoy seeing all ur videos.............ive watched every one of them at least 20 times each......................thanks for all the videos and your safety talks are awesome................keep'em coming oil burner.............look forward to more insane and crazy ideas you come up with
Wow! Thanks very much for your kind words. I'm stoked to hear you have been able to put the things to good use. Some people seem to get them lit first time out and some have trouble. It did take me a while to get the knack of it but once you learn what to look for it's second nature. Just have to keep in mind they have to be HOT and the rest takes care of itself.
What do you do with all the aluminium? Do you cast it or sell it for scrap? I have melted things inadvertently as well. I get a lot of questions about is it hot enough to do this or that. Problem is not will it melt it, the problem is don't take your eye off it or you'll melt every damn thing!
Thanks again for the feedback. It's hearing from people like yourself that make this rewarding to go on with. I really appreciate hearing what you have done with these.
where I live it is way up northern Canada and only way to get out of town is by flying..............so I melt all my own metals for casting and making parts for anything from a kids toy to heavy machinery............as it is sometime impossible to get parts and supplies to my location............we don't get regular flights up here everyday sometimes only once or twice a week so I have no choice but to build all my own stuff...........even if I order stuff the cost of the freight is sometimes way more than the part itself so it really saves me a lot of time and money by building and making my own things....................sometimes I do sell my aluminum, copper, brass, cast iron ingots to a scrap yard but I have to wait until end of January once the winter roads are made and open....................I have a thermometer and when I tried to measure the temperature of my foundry it goes overlimit and the thermometer is rated up to 4200 degrees farenheit ...............veg oil is awesome ........keep making your videos and I will keep watching and enjoying them..........thank you very much for a very interesting topic....................last night I made a burner with propane tank and the flames were shooting out of it like about 15 ft of pure madness...lol........................thanks for all your awesome and cool videos oil burner
Thanks for this video. It just gave me an idea for fueling a little foundry I am planning to build.
I have never seen this done! Thats awesome and cleaver!
That sounds just like Bell Uh-1 Huey!
Can anyone explain me what is this device? What can it be used for? Thank you in advance...
melting down certain metals into ingots if i'm not mistaken
You didn't even read the first line of the description??
No, I like to communicate with people.
Animated Anatomy
Well that's one way of justifying it.
so you just around clicking on videos without even reading the title?
That long cool droning sound the fire made nearly made me fall asleep on the freeway. It freaked me the fuck out. I regained consciousness and realized I had driven 5 miles at 70mph without any memory of it.
A while back I bought a used wood boiler furnace . I set it up to heat a large concrete slab with pex tubing . I've thought many times about trying to retrofit it with something like what you have . With the kind of heat produced in your vid it would be a great savings to my heating bill in the winter time . Your video is great inspiration !
Thanks for the kind words. I cut a LOT of wood for my elderly father to use in his wood burning heater and know how much work that is. I'd so love to convert it to oil for him. So much less work with more than adequate heat.
If you used something like the fuel control I have in one of my other vids and developed some saftey systems like under/ over temp or flame sensors, these could be made every bit as safe and reliable as commercial units. I'm working with some small electronic boards from fleabay to create some controls for this very purpose.
this would be great to spool a turbo and alternator up powering and charging a 12v system...
and i did not know we could weld whit no gloves that was amazing. so i dont.have to worry getting electrify thanks again 😜
As i sat barefoot on concrete wearing only damp swimtrunks and a cutoff t-shirt, I felt a little bit of a zap while MIG welding a kickstand on my MX bike, so no, not completely safe. I simply took my spare hand off the footpeg and used both hands to hold the torch, and finished the job ;)
@@justindunafon8580 😮
Got a waste oil burner at work - brilliant piece of kit. 20 litres a day heats the entire warehouse.
Wow! you almost blasted a hole all the way to the atlantic ocean. Awesome
There will always be those that want to throw their safety warnings around. If you are to the point where you can actually cut with a torch then I am sure that you have at least looked at the book that came with it. Or perhaps noticed all of the leather shit hanging on the peg hooks next to the equipment at the store. Give the guy a break, he took the time to make a video and share some knowledge with the rest of us. I have used a plasma torch without all of the necessary leather, if it’s cold I wear the jacket if it is 110 I opt for just the gloves. What he does is his business. Calling someone names because they took time to make a video for others? 9 seconds into the video you can see he is not wearing gloves. If his safety bothers you that much then you should hit your back arrow at around 9 seconds. That way the conversation will actually remain about the project. For one I say Thanks for the video!
Thanks Tom. I appreciate your comments and support. It means a lot!
Welding like a boss :)
Works great! Thanks for sharing the project with us.
I love this burner and will be making one. thanks for sharing.
cooool! i like Burn!
I love how you used an old fire extinguisher for that... so ironic :'D
Sounds like speeding locomotive - I love it!
Awesome burner! I love the sound it makes. I’m thinking of building one like it for a trash incinerator
holly shit .. half way of this video sound like a choppers or steam locomotive .. then at almost end of video just like a turbo .. how cool is that .. plus the tank I though it will explode due of white smoke . but it did not happen .. just burning the pain .. wow
it may be worth learning to weld with projects like this
+Jamie Malee My welds do not fail. there is no big deal if they do. I am not welding critical components.
Have you ever welded anything in your life?
+Oil Burner I like you, you can deal as good as you're served
+Oil Burner clean metal welds better and holds better. plus the wire speed was a bit slow
The cold beer part sounds pretty good😋
The sound is strangly soothing
Clean power !
Not clean
its a crime not boiling a cuppa or frying an egg on that
9:40 *GET TO DA CHOPPAH!*
Dead-on sound for a Huey...
made my day xD
hahaha ... I thought it sounded like a steam train .
It does sound more like a steam train engine
It's a bit slower than a Huey but sounds very much like it.
It was still idling on the ground. Gets faster as it lifts off! :0)
Did not realize I had a welding OCD until I was in physical pain watching you weld a dirty surface.
That bucket is not filling up with fire, must have a hole.
+Anton Morris Then fix it dear Anton, dear Anton, dear Anton, then fix it dear Anton, dear Anton fix it.
+Anton Morris you are right I agree with you, its not shown in the video, how to light it initially, which should be guided.
ان افهم شي
Pra q serve isso?
João vitor facundo
Para nada, o cara lá só fez por fazer, só fez para fazer uma experiencia e mostrar em vídeo, combustão de um óleo ou gás projetado por um turbina elétrica :v
I loved how the fire changed it's pace or beat!! LOL!!!
I LOVE YOUR VIDEOS MAN! Such a great, informative and really educational channel that deals with real world, usable information. I've enjoyed all of the videos I've watched and can't wait to fabricate my own oil burner now. Keep them vids coming, please... BTW, love your sense of humor also. I wish I was your neighbor, but I'd come over with a case of beer and to help you as your assistant, not to complain!
It sounds a little like a steam locomotive.
That it does
well... what time it starts to fly? ¬¬
Fantastically innovative - well done. I'm proud to see what my fellow New South Welshmen get up to.
+dickclements Thank you! Much appreciated.
That works very well, good job!
10:28
Flashback to when I was in 'nam..
What's with all the Nanny comments???. In the First World War 14 year olds would lie about their age so they could fight, now people are scared of a bit of DIY!. I think your next vid should be blind folded chainsaw juggling :-)
HILUX CHAINSAW How about we use the burner in the furnace in my other vid to render down some of the saftey sissys? Your sentiment is spot on though. It's amazing how western society has and is faster becoming a bunch of pathetic wimps scared of their own shadow or breaking a fingernail.
The saftey zealots make me sick the way they undermine the efforts of people to do things for themselves.
HILUX CHAINSAW Bet these Nannys never welded or built anything. They just read magazines
use nanny-lube-pro and stay calm
Hilux chainsaw nice profile picture, peacock butterfly
I live for this kind of stuff. I'm building one of these this week, and I'm going to use it in a furnace I'm building out of a big water tank. Can't fuckin wait!
I just found this channel yesterday 8/21 and it’s great! I need an oil burner to get rid of waste oil. Fantastic.
I'd be interested to hear more about your needs for disposal. How much you need to get rid of over what time frame? I was thinking of building a mega burner but saw no practical use. This could be the Justification I need! :0)
I have quite a bit of used oil, just being stored. You have given me several ideas with this, Thanks. Keep up the good work. Liked, and subscribed.
Once started, could a turbo be mounted some how be used to force air back into the chamber?
Yessir! It has in fact been done!
Emission like Volkswagen TDI ;) :-)
the best engine of it's class. Most popular in the Europe. Bulletproof! You can do over milion kilometers on TDI. Who cares about emission...
Michal Rimmera k وللله اءنته ذكي
مفهمتش علاش راهم يحرقو فتارب
Michal Rimmerak but a lot better
Isn't it a bit odd tho' that someone in the US 'discovered' that a 'European' vehicle was allegedly breaking the regulations .... Now how about going and testing a load of American Diesel powered cars the same way and see who else is 'cheating' and by how much.
Im not sure what i need it for but I want to build one, I was mesmerized by this video and watched the whole thing
Great idea! I know just how to utilize this basic concept for our use here up North. Thanks for posting!
+blackwunk No probs. Have a look at my other burner vids as well. I have some different designs for different applications.
10:00 Get to zhe Choppah!
how come nobody reads the video description before making stupid environmental green washed comments?
great vid. i want one of these in my hobo bus.
GOOD question mate and I wish I knew the answer. Can't make it any clearer than what I have.
I think I'll see if I can do something like this. With all the used oil from cars and tractors, I should be able to figure a way to get some heat and lessen the burden of the gas man! Great video. Thank you
Thank god I have found your channel, now I finally have some interesting shit to watch. At least you have some real informative shit that is also adaptable for other uses, you would be surprised how much people would get from your work, keep it up .Thanks Mate.
Гудронный коллайдер)))
Sounds just like a Huey.
+Tom Keir vietnan haha
+Tom Keir it's like steam train for me haha
now that you mention it, it does
Tom Keir yeah
Thanks for sharing this idea - it has lots of potential uses -
Cool, built one out of a car's exhaust few years ago, I used a reversed vacuum for blower and got blue flames.
I realize that some people like to act tough, but welding with no gloves and tacking before you used a mask is just plain idiotic. Ill plasma cut with just glasses, screw the tint, but welding without a mask or gloves is just idiotic.
Please add an annotation or something so some moron doesnt hurt themselves because they saw you get away with this.
Thanks for the laugh! Does two idiotics make a sensible?
How about an annotation that says " If you are a candy arse saftey sissy, leave DIY stuff like this to your husband and you confine yourself to knitting and scrapbooking.... only with saftey scissors and rubber kniting needles". OR, how about " This is a DIY channel not a kindergarten. If you need to learn basic, fundamental saftey issues to prevent you hurting yourself, please visit the appropriate channels aimed at your level of incompetence. Your stupidity is not my problem or responsibility". Anything else? " Look both ways before you cross the road"? "Don't drink weed killer"??
I have given up on trying to protect morons and idiots.That's their Mummys job or people that never do anything themselves but have a disposition for championing the cause of protecting the inept and stupid.
Oil Burner
how about adding a warning this video is not for morons and idiots
Leigh Davis While to a normal person that is a totally logical suggestion, the problem is a moron would either not read or fail to take any notice of a warning anyway. It may however appease the semi idiot safety zealots so would be worthwhile from that POV !
As someone commented, All the equipment comes with safety warnings in the handbook and stickers everywhere so if the idiots have taken no notice of this already, why would they take notice of anything I did and WTF do people think it's my job to play mother? If idiots Hurt themselves, GOOD!
Not like they are an endangered species, there is no problem at all if a few want to cull themselves.
yep can't fix stupid lol
Oil Burner I dont care how you word it.. Either of the options you gave would still work, but why not just "remember to always follow all safety instructions, I am not responsible if you get hurt repeating this process." Simple, respectful, and absolves you of a potential frivolous lawsuit because guess what? We live in a country that people like to try and sue everyone and blame everyone else for their carelessness. Why not take a simple step to avoid any hassle from the morons and make all the people telling you, you should do it shut up instead of turning this thread into a giant argument?
Предупреждаю, ролик нужно смотреть в сварочной маске.
This is very nice and educational vid,thx. for sharing,cheers mate ;)
I have no idea what people are bitching about this is a damn good use for waste oil.
they bitch because they have no experience or knowledge of the things but feel compelled to appear important by parroting some other crap they have no clue about to gain the approval of the other ignorant whingers. :0)
come on kids get your marshmallow the fire is hot.
the vitamins and minerals are a bonus!
+Jasman35 and also cancer)
and.... zzzzzzzzz?
thank for the reply, keep the videos coming. pretty cool stuff :)
Brilliant obviously you've done a good job of it!
Any information on how long a 200 litre barrel would last with this? The heating potential of this little thing is pretty big.
I have used one I got years ago and is still fine.
+Oil Burner - you mean the barrel of oil? you're still running with the same barrel??
How long roughly?
Really do like this by the way.
+ss ss - sorry ignore "how long" - even a year is amazing. we fill one of these in a month at work.
Sorry, I thought you meant the drum itself. I have vids where the drum is a burner and get asked how long it will last before burning away.
As for oil consumption, it depends entirely on how much heat you want to get out of it. If you ran the thing at 300Kw for metal melting you'd get about 7 hours out of a drum full. If you ran it at 30Kw for home heating, you'd get 10 Days heating for 6 hours a day. If you ran it at 10Kw for water heating, you'd probably have hot showers for a month. All depends how you use them and how much heat you are pulling out of them.
Oil Burner - I see. That's great, just wanted a ball park figure.
Cheers.
Is there helicopter flying nearby? lol
Kamil x I think it sounds like a Steam Locomotive working hard up an incline.
That's one hell of a contraption you made there, well done. Wish I knew more about what kind air blower that is and what not.
Thanks.
In practice it was a poor air blower. Was from a car. Some are good, this one was not. Normally I use Jumping castle blowers. Fairly easy to get on Fleabay and the like and cheap. See my many later vids.
wow -- the faint dialogue in the background reminds of Dark Side of the Moon along with the backfiring of the burner
Good hair dryer for my girlfriend :D
Could use it for waxing her legs too!
"Watch as we remove you hair in 1/10th of a second!"
kill her with smoke in the process by the look of it. Be very careful drying hair.
HaHa LOVE the description! People on youtube can most certainly be asshats.
+utoobube it really spoils the whole point of putting vids up to show people ideas when all so many do is look for irrelevant shit to bitch and whine about to elevate their own non existent status and empty lives. Not even 1% of the whining comments I get are from people who have ANY vids up of something they did.
I'm not bothering to respond any more other than to just delete the idiotic comments as they appear.
I understand. TH-cam is full of armchair experts who are able to tell ppl exactly what they're doing wrong...and yet seem to not do anything for themselves. Keep on keepin on my man, Ive enjoyed the videos of yours Ive watched today.
+utoobube Thank you. it's knowing people enjoy them and get their own ideas for things they can use that makes the effort in doing and putting them up worth while.
Much appreciated.
All the people saying he should have recycled that oil. He didn't want to recycle the oil he wanted to make a badass oil burner and that's okay.
Fking recycling!
I DID recycle it into a fuel for burners to make heat. Currently I'm working on one to heat my house over winter. I will get a lot more out of the oil in using it as a fuel and the savings I'll make heating my house with it than I would " recycling" it and giving it to someone for nothing.
Then you can get oil before it gets dropped at the recyclers and burn it too . Hell maybe even put the oil recycler out of business for the green gods. Screw these libtard green global warming nuts we should use them for fuel but it would stink.
that kicks ass, you the man!
Pretty neat, but what does it do?
+iweld Alexander If you read the description or looked through my other 75 vids and can't work it out, probably not much point trying to explain.
+iweld Alexander It's a waste oil burner. It burns waste oil.
+Oil Burner everyone does not have time to watch 75 vids of someone to understand a thing, if you dont want to answer, dont, you dont have to be rude
+TheFF47 Nor do I have to explain what is already in the description that people can read themselves nor answer every question already covered at least 50 times before. Sorry if me not doing what people are too lazy to do for themselves offends anyone. I try to answer the intelligent questions that are not covered for those genuinely interested.
Unfortunately I don't have time to keep going going over the same old things for those that are not.
Sitting here wondering how many times he has burnt the fuck out of his hands.
+TheBCSledder I wonder how stupid people like you must be to believe If I had of burnt my hands i would ever done it again repeatedly. YOU may be that stupid but not everyone else is, nor a brain washed safety zealot whinger.
Oil Burner I know this may be late but your rude as hell
awesome... you gave me some really great ideas. next step is putting them in action. thank you.
I try to show these as a heat source rather than cover every application. People have used these for grain dryers Chook shed and greenhouse heaters which I would have never thought or or have access to anyway.
Bit like an industrial engine. You get the motor and put it on a lawn mower or a rice huller or a cement mixer or brick conveyor... whatever your purpose.
For some reason it seems many people can't understand that and have to keep asking " What's it for?"
I guess if you can't figure out what you can do with it, you didn't have a use for it an the first place.
What is your intended application?
This are great applications i been to places where such tools can be a great help. Thank you for the time and work you do. Have a great day. And keep the ideas flowing.
Love the rhythm of the thing.
You would definately get higher quality welds if you would put the effort into grinding all the paint and whatnot off of the perimeter of your welds before welding the pipes in.
Yes I would. I have been slack with things like that.
yeah. i am 100% sure he needed you to point that out.
@@fredgarvin4482 Obviously he did need it, or else he would have done it right the first time lol.
Why all the dislikes?
Safety nazis, greenwashed environmentalists and general trolls with nothing better to do get upset at what is shown here.
Oil Burner Looks safe enough to me
homerun443
Clearly you are a practical man that has a pair and not a whining safety Sissy. Most of the complaints are because I don't wear gloves when I'm welding.
There are so many people that get upset when you don't live your life the way they want you to or do what they want not make your own decisions.
Oil Burner amen to that
+Oil Burner a min
Awesome burner 👍.
Though I cannot and do not weld, I enjoyed the video. I am a wood worker and love making things with my own two hands, so when I see others doing the same with other mediums, I enjoy just watching and learning even if I will never use the knowledge. Thanks for showing. BTW, I am subscribing so that I can see you put your skills to work on other projects. Maybe some day I will make videos of my own work projects.
+William Weaver I can relate exactly. I am hopeless with wood but I watch Vids on it all the time particularly people turning huge slabs into bowls and the like. When you put Vids up here you certainly get a lot of arseholes making stupid comments but then you get comments like yours and other people who use the ideas and benefit from them and it all becomes worthwhile and rewarding. I just have fun with the idiots now and appreciate the kind words people are good enough to say.
Thanks for your support, it is greatly appreciated.
why all the hard work to make this just get a ford it will burn your oil for you
with this burner you can melt aluminium or anything scrap you want to melt, you only just add a stove and melting bucket,,, very useful ,, turning trash into treasure
thanks to this video
I hear Chevy burn it faster!
Ya because we want to drive GM made in china and funaced by American tax dollars....fucking idiot.
@@dougm2681 its a joke doug calm down
Sm...Sma....SMOOOKE....whaaaa.....quick...some one get me to a tree thats needs a huggin!!
super genial! me has dado una gran solucion para mi empresa! te mando un abrazo
I love how the main body of the burner is a fire extinguisher.
A certain Irony don't you think? :0)