Not buring clean. Air into combustion pan, setup for rotation and use the incoming airflow to cool the pan outer edges, keep heat in the centre/bottom of pan. Oil feed best dropped from height into the pan away from flame as it will likely burn oil in feed tube and carbonise blocking it. Final advice for anyone building these, all combustian gasses need to be exhausted outside. Waste engine oil contains a lot of nasties to humans and burning it indoors releases these back into the air. Example: We used to have a commercial unit buring our waste aircraft engine oil, I remember all the yellow deposites that would form around the hot air vents until I relaised what they were. The very same yellow deposits I would have to wash off the underside of the engine cowles near exhuast or blast off spark plugs. It was Lead and we in the workshop were breathing that Lead from the oil.
The intake air is burned and expelled. You dont want to pull in your warm air from inside and push it outside. Use outside air supply to fuel/oxygen for your heat.
You are the best! So great to watch you work! I am a poor welder and really appreciate your skills. Just found your channel and subscribed immediately. You are an inspiration.
Масло не успевает нагреваться, как итог плохое сгорание, трубу нужно сверху внутри камеры сгорания проводить прогретое масло будет давать больше тепла и лучше сгорать, да и кстати закрывать такой котёл нужно герметично чтобы пары сгоревшего масла не нападали в помещение, для того и ставиться вентилятор принудительной тяги😂
If you want the use of the stove to be better, add a water drip with which you will feed small drops of water into the oil feeder during combustion. You'll thank you when you don't have to clean such a stove from dirt :)
I'm going to build one but add more of a down ward slope to the oil feed line to keep from build up and then feed the oil line through the blower tube as to help pull the oil from the tip of the oil feed cause they can build up with soot in a short time. Good build though
В более менее герметичном помещении, воздуходувка создает пониженное давление воздуха в помещении и повышение внутри камеры сгорания. При негерметичной камере сгорания это создаст круговорот помещение - воздуходувка - камера сгорания - помещение, постепенно наполнив воздух продуктами горения и выжжет кислород чем убьет людей в помещении. При герметичной камере сгорания это вызовет быстрый выброс теплового воздуха в дымоход (он не успеет отдать тепло) и засос холодного воздуха в помещения сквозь щели в стенах/окнах/полу/потолке, что даст низкий КПД обогрева.
I would add a support between the floor and the two horizontal pipes (air & oil) but apart from that, excellent! PS: It is now illegal to burn waste oil here in the UK, partly for the 'environmental issues' but mostly because the government can't tax it! 🤣
Doesn't burn clean until it's up to temp, made several of them over the years. Smells like ass until you get it up to a good combustion temperature, and that stock pot won't last long !
I've made one. Working on another one. Air and oil control are very important. I installed a needle valve in my first one. Will again on my second one. My first one worked really well. Oil control was adjustable down to a hair stream. Only trouble was when I sent it to the weld shop the guy that took my instructions was a young welder and didn't understand how flues measured and installed too small a pipe. So I had to run at a hotter tempt to vent well
"...the pipes will serve as legs for..." well, we saw that coming! Sorry, I had to move on - too much time spent on the tablet commercial. Greg [garden grove, CA usa]
Мне кажется что подача масла и воздуха должны вместе регулироваться. Подойдет перистальтический насос с редукторным мотором. А регулировать напряжение одновременно на воздушную турбину и насос для масла. 😅
The oil pipe that feed the burner must have 1° slope and I suggest you put the faucet as much as possible at the bottom of the oil tank so you can burn it all. You need also a purge valve at the oil tank bottom so you can clean oil residues that deposit at the bottom. You can cut the upper lid of the burner and mason some thermal bricks inside to store more heat. Well, you can improve a lot :)
Привет!🤝интересно получилось,лайк!такого вида печи я делал на дизельном топливе.теперь нужно в нее сварить теплообменник и сделать водяное отопление в мастерской.
@@meytv5691 ну может сейчас время конечно другое,а в 90х,начале 2000х такие печи очень даже были в ходу ,их и без принудительного поддува делали,правда розжигать дольше,пока не начнет воздух засасывать.
When it flares up, you can add a little water along with the oil, the effect will be like that of a jet engine. The main thing is that the stove does not melt.
I would love to see how more efficient a waste oil stove would be if it was attached to a sand battery. At least 100 lbs of sand stored in a metal enclosure attached to a sidewall of the stove. After 4 or so hours, that sand battery should be close to 400 degrees and last for hours after the stove is out. It could cut the oil use in half. But I would to see a real world test of this.
I dont know about your laws, but in most places of the world they will give you a insane fine for this stove. Burning waste oil a lot of times is a very poluting process. Some years ago i built a oil heater but i had tons of problems and judging only by the looks of your i doubt it will work,first you have a huge burning camera(the pot)which will melt when it goes to temperature, but this will never happen because this blower is far too small for the camera.I used old diesel fuel injectors to spray the oil like a mist and the it was burning 100% but i still got thick smoke
would be a great idea to implement some kind of water line in the otherwise unused top part of the fire chamber - to squeeze some more efficienty out of it. Great idea tho. much appreciation 👍
Well as i have ordinary sense, rather than make hole iinfront side u may use think glass it makes more atteacting/ seal packed and also avoid the burning fuel smell
Very nice. The only problem I could see is the air pipe not being sealed at the bottom. If the oil burn pot gets a hole or a leak it’ll burn out the bottom onto the floor.
Pas mal ! 👏 Pare compte...si il n'y a pas de courant de 220/24/12...Volts, pour alimentation turbine 🤔??? ...ont fait comment...🤔??? Nous sommes pas complètement autonome 🤔 Triangle pyrotechnique = combustible + air + étincelle = 🔥
Postavio sam klip moje peci na preradjeno ulje za centralno grejanje, napljuvali me kao zagadjivaca, kao u evropi to nemoze, evo vidis da moze 😂😂😂 Pozdrav iz Srbije.
My thoughts exactly. Has to be makeup/supply air from somewhere when exhausting to outside. I wonder what net gain is, setup as shown. Not knocking, honestly curious about the numbers...sorry, I'm a nerd & love numbers!
You are a struggling man and appreciate your beautiful work, and I loved that, and I'm just like you, I have great ideas, and I subscribed to the channel again, and I'm from Syria, and I love that work. Do you use car burnt oil?
odlična peć . Imam orginalnu na staro ulje i super je to što sve sagorijeva. Jedino ti dozator na tu pipu nije baš nešto.. Moja ima nekakav rotirajući mehanizam koji gura to ulje i promjenom broja okretaja se regulira tok .. To može grijat tako jako da pocrveni. Stavi još neki ventilator po tome da puše . Bolje će grijat . Samo ne prejak da ne smeta snimanju. JA ne mogu snimat kad moja radi . I da , stavi još jednu tavicu na čemu će gorjet koju ćeš moći lako izvadit van zbog čišćenja .
Probaj onaj dozator za infuziju uzet, koji regulira kapanje infuzije. Mada najvjerojatnije neće raditi kako treba jer je ulje gusto. Al da bi kojim slučajem radilo bilo bi odlično rješenje
Представим такую ситуацию: отопитель работает, вы отошли на 10 минут из гаража. В это время отключилось электричество. Наддув прекратился, а масло продолжает гореть. Кастрюля наполняется горящим маслом, потом оно горящее вытекает на пол и в гараже становится уже не тепло, а слишком жарко.
Bravo komšija svaka ti čast. Odlična ideja i sjajan video, još kada bi znao to sve da napravim haha, ali bitno da je tebi toplo i da ćeš udobno praviti nove ideje a mi uživati u tome. Pozdrav iz Srbije
According to the flame you should have some pollution gasses on that pipe outside, when flame is blue than you have good and complete oil burn without waste, pollution and high efficiency... so, back to the drawing table and we are waiting for part two, when flame is blue... thanks for sharing your video...
Actually, he is burning waste oil with lots of impurities - not going to have blue flame. Also, you do not get blue flame from burning wood. His exhaust is very clean for burning waste oil. Natural gas and propane have blue flame when complete combustion, but that does not apply to wood or waste oil. I am very impressed with his clean burn considering his fuel. I am an engineer.
Můžeš si tam nainstalovat různé přepážky nebo nahřívat keramická tělesa nebo šamotové desky a účinnost hned zvýšíš. Nebo dovnitř nainstaluješ výměník s vodou a rozneseš teplo do radiátorů.
There are off the shelf options with pollute less than wood burning stoves and in their overall scheme more environmentally friendly. As long as you are the person who has the waste oil or can source it locally.
I heard you have oil
knock knock
He needs democracy
We can build a d355a faster than you can send people
Dare !
I burned it all sorry 😢
🤣🤣
Not buring clean. Air into combustion pan, setup for rotation and use the incoming airflow to cool the pan outer edges, keep heat in the centre/bottom of pan. Oil feed best dropped from height into the pan away from flame as it will likely burn oil in feed tube and carbonise blocking it.
Final advice for anyone building these, all combustian gasses need to be exhausted outside. Waste engine oil contains a lot of nasties to humans and burning it indoors releases these back into the air.
Example: We used to have a commercial unit buring our waste aircraft engine oil, I remember all the yellow deposites that would form around the hot air vents until I relaised what they were. The very same yellow deposits I would have to wash off the underside of the engine cowles near exhuast or blast off spark plugs. It was Lead and we in the workshop were breathing that Lead from the oil.
Skip to 7:55 for the actual building start...untill then is a tablet marketing.
One recomendation i think would be great is to add a inline fan that would suck ambient air from outside instead of the air in the heated space....
Why is it better to suck ambient air from outside instead of the ambient air from inside?
The intake air is burned and expelled. You dont want to pull in your warm air from inside and push it outside. Use outside air supply to fuel/oxygen for your heat.
You are the best! So great to watch you work! I am a poor welder and really appreciate your skills. Just found your channel and subscribed immediately. You are an inspiration.
Using the zip ties as spacers was clever - thanks for the tip!
Zagadjenje 100%. Ja sam napravio za moju garazu malo drugaciji sistem ujutru sam je ubacio i u 12 sati sam je izbacio. Drva su zakon
Everyone should have one like this. no oil problems and the air would be clean. I live in a house with 10 rooms so I make one for each room
Масло не успевает нагреваться, как итог плохое сгорание, трубу нужно сверху внутри камеры сгорания проводить прогретое масло будет давать больше тепла и лучше сгорать, да и кстати закрывать такой котёл нужно герметично чтобы пары сгоревшего масла не нападали в помещение, для того и ставиться вентилятор принудительной тяги😂
If you want the use of the stove to be better, add a water drip with which you will feed small drops of water into the oil feeder during combustion. You'll thank you when you don't have to clean such a stove from dirt :)
Nice looking set of home made vehicle ramps nice to see you making a heater for your shop doctor d.s
I'm going to build one but add more of a down ward slope to the oil feed line to keep from build up and then feed the oil line through the blower tube as to help pull the oil from the tip of the oil feed cause they can build up with soot in a short time.
Good build though
You did a beautiful job! I think I am going build one now!
I haven't started watching it yet and I already like it 😅
В более менее герметичном помещении, воздуходувка создает пониженное давление воздуха в помещении и повышение внутри камеры сгорания. При негерметичной камере сгорания это создаст круговорот помещение - воздуходувка - камера сгорания - помещение, постепенно наполнив воздух продуктами горения и выжжет кислород чем убьет людей в помещении. При герметичной камере сгорания это вызовет быстрый выброс теплового воздуха в дымоход (он не успеет отдать тепло) и засос холодного воздуха в помещения сквозь щели в стенах/окнах/полу/потолке, что даст низкий КПД обогрева.
in germany not allowed in private homes . And for good reasons . Look at the color of the flame . Not hot enough for a clean and effectiv burning .
you are not supposed to put it in your house it contains chemicals it is a workshop stove.
Who cares
Germans burn lignite ffs, literally the worst form of fuel possible for emissions!
Also banned i the rest of europe…but you guys ignore that!😂
I would add a support between the floor and the two horizontal pipes (air & oil) but apart from that, excellent! PS: It is now illegal to burn waste oil here in the UK, partly for the 'environmental issues' but mostly because the government can't tax it! 🤣
Never bothered me lol
Its already been taxed till the hilt
Only illegal if you get caught friend.
Because as we all know the more tax revenue the government gets, the more likely the environment will be saved. NOT!!!
Doesn't burn clean until it's up to temp, made several of them over the years. Smells like ass until you get it up to a good combustion temperature, and that stock pot won't last long !
how about if you replace the stock pot with something like well designed clay pot used for cooking will it able to withstand the usage for long?
I've made one. Working on another one. Air and oil control are very important. I installed a needle valve in my first one. Will again on my second one. My first one worked really well. Oil control was adjustable down to a hair stream. Only trouble was when I sent it to the weld shop the guy that took my instructions was a young welder and didn't understand how flues measured and installed too small a pipe. So I had to run at a hotter tempt to vent well
a small sight glass on the side would be helpful to know oil level. over all nice build
Odlicna pec na preradjeno ulje👌Dao si mi super ideju,da i ja napravim tako nesto za radionicu👍Veliki pozz za tebe,Doctore👋
Build us one please all these numpties commenting on here with there negativities is killing me well done doc
Stove video, not a commercial for a tablet
Its how people pay for the video production.
Wow. Look at that. A tablet woth features that every other tablet has. Wooow ooooo weeee.
"...the pipes will serve as legs for..." well, we saw that coming! Sorry, I had to move on - too much time spent on the tablet commercial. Greg [garden grove, CA usa]
Мне кажется что подача масла и воздуха должны вместе регулироваться. Подойдет перистальтический насос с редукторным мотором. А регулировать напряжение одновременно на воздушную турбину и насос для масла. 😅
Best oil stove design....but you should use external air for combustion....Easy modify...thanks for the video
Awesome work and inventions
The oil pipe that feed the burner must have 1° slope and I suggest you put the faucet as much as possible at the bottom of the oil tank so you can burn it all. You need also a purge valve at the oil tank bottom so you can clean oil residues that deposit at the bottom. You can cut the upper lid of the burner and mason some thermal bricks inside to store more heat. Well, you can improve a lot :)
Have you got a video of your build?
@@TheNinja691 I didn't think to burn wasted oil until seeing this video, having a working model on which you can improve is great!
Привет!🤝интересно получилось,лайк!такого вида печи я делал на дизельном топливе.теперь нужно в нее сварить теплообменник и сделать водяное отопление в мастерской.
не повторяйте глупого доктора.
@@meytv5691 ну может сейчас время конечно другое,а в 90х,начале 2000х такие печи очень даже были в ходу ,их и без принудительного поддува делали,правда розжигать дольше,пока не начнет воздух засасывать.
@@meytv5691 конечно такая сейчас мне лично не нужна,газ,либо электро котлы сейчас в ходу
amazing the first video witout stupid voices and straight to the point !!! love it
When it flares up, you can add a little water along with the oil, the effect will be like that of a jet engine. The main thing is that the stove does not melt.
Podrska za bracu hrvate. Pozdrav iz Crne Gore.
tomorrow's matches any insider tips from you guys would be gold right now
Very very neat! Keep up the good work.
That's a very long ad for a tablet
Вентель подачи надо было ниже приварить масло неполностью попадёт в горелку 😊👍
I would love to see how more efficient a waste oil stove would be if it was attached to a sand battery. At least 100 lbs of sand stored in a metal enclosure attached to a sidewall of the stove. After 4 or so hours, that sand battery should be close to 400 degrees and last for hours after the stove is out. It could cut the oil use in half. But I would to see a real world test of this.
Druze svaka cast za ideju samo pazi da ne updnes u problem sa zakonom👍👍👍
Браво момче!
Сјајно одрађено!
Nice! Recommendation make shield where oil flow in pipe, to prevent water from entering in oil.
Really really interesting and really really cool 🤩👍
very nice for the winter!
I dont know about your laws, but in most places of the world they will give you a insane fine for this stove. Burning waste oil a lot of times is a very poluting process. Some years ago i built a oil heater but i had tons of problems and judging only by the looks of your i doubt it will work,first you have a huge burning camera(the pot)which will melt when it goes to temperature, but this will never happen because this blower is far too small for the camera.I used old diesel fuel injectors to spray the oil like a mist and the it was burning 100% but i still got thick smoke
Smoke is a by product of incomplete combustion
would be a great idea to implement some kind of water line in the otherwise unused top part of the fire chamber - to squeeze some more efficienty out of it. Great idea tho. much appreciation
👍
one little tip - you did all "hair" seals (plumbing hemp) in opposite direction :)
I think your wife would be more upset about you using her hair to seal threads than using her pot.
Wenn das die Grünen sehen kriegen die einen Kollabs😁😁
Eigentlich jeder weil das konstrukt blödsinn ist
# TEAM MELONEEEEEEEE !,!!!!!!!!!!
f..k the greens
Diko..odlicno..my croatian ❤️💙🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🇭🇷🇭🇷🇭🇷🇭🇷🇭🇷
Awsome video I have built a few oil burners and they put off just as much heat as my wood stove and if you a car guy easy way to get rid of used oil
Emite contaminación por humo.?
In worst way possible for the environment😂
@@marcoroa8223of course it does, wouldn’t recommend breathing it in
Nice work,i need to build one,ive been saving up waste oil haha
Very nice job, keep going ❤
Kao jedan od najvećih fanova javljam se za udomljavanje tableta ako već nije udomljen😂
Hehe udomljen je već kod mene 😂😂
@@DShomemade auuu....za dlaku je bio moj😂😂😂....
Jetzt noch eine Wasserspirale mit eingebaut und schon hat man Warmwasser.
Well done!👏🇨🇮🇵🇸
Well as i have ordinary sense, rather than make hole iinfront side u may use think glass it makes more atteacting/ seal packed and also avoid the burning fuel smell
need to put a brake rotor (disc) above burner to extract more heat , its all going out the chimney
mine runs about 900 degs. had to put bricks between it and the wall
Very nice. The only problem I could see is the air pipe not being sealed at the bottom. If the oil burn pot gets a hole or a leak it’ll burn out the bottom onto the floor.
great job!! where did you get the blower?
Ортадағы асқана ыдысы өте жұқа отқа төзімсіз, әрине ұзаққа төзімсіз.
Muy buena la idea pero se paso para ahcer publicidad que no venia al caso, de hacer la estufa. Si haces publicidad que sea un poco mas disimulada
😠 ~ had to skip ⏭
Pas mal ! 👏
Pare compte...si il n'y a pas de courant de 220/24/12...Volts, pour alimentation turbine 🤔???
...ont fait comment...🤔???
Nous sommes pas complètement autonome 🤔
Triangle pyrotechnique = combustible + air + étincelle = 🔥
just add a couple of 1" or 1 1/4" pipes at the top and connect them together. plus a circulation pump and 2 radiators and substantial heat.
Postavio sam klip moje peci na preradjeno ulje za centralno grejanje, napljuvali me kao zagadjivaca, kao u evropi to nemoze, evo vidis da moze 😂😂😂
Pozdrav iz Srbije.
😂Pozz
Great job, but you should suck air from outside, so that you dont remove the hot air from inside your workshop. 😄
heat rises, and this being on the floor will remove the cold air from the workshop floor
@@RakTheGoose the hot air from the stove will circulate the air, simply by heating it. No need to use inside air to get circulation 😁
My thoughts exactly. Has to be makeup/supply air from somewhere when exhausting to outside. I wonder what net gain is, setup as shown. Not knocking, honestly curious about the numbers...sorry, I'm a nerd & love numbers!
But the air outside is heavily polluted from burning motor oil 😂
My only concern is that cooking pot, the metal is too thin, will burn through eventually
An the good thing is, oil burns for a long time, so good for overnight burns.
very nice work.. but i would try to upgrate with closing the combustion chamber and create 4 exhaust pipes heating the inside walls
Good work, what fan did you use?
80W Aliexpress 😅
Eres mi ídolo !!!❤❤
You are a struggling man and appreciate your beautiful work, and I loved that, and I'm just like you, I have great ideas, and I subscribed to the channel again, and I'm from Syria, and I love that work. Do you use car burnt oil?
Thank you very much, that is the oil from the car.
odlična peć . Imam orginalnu na staro ulje i super je to što sve sagorijeva. Jedino ti dozator na tu pipu nije baš nešto.. Moja ima nekakav rotirajući mehanizam koji gura to ulje i promjenom broja okretaja se regulira tok .. To može grijat tako jako da pocrveni. Stavi još neki ventilator po tome da puše . Bolje će grijat . Samo ne prejak da ne smeta snimanju. JA ne mogu snimat kad moja radi . I da , stavi još jednu tavicu na čemu će gorjet koju ćeš moći lako izvadit van zbog čišćenja .
Da, Hvala ti 😁 Pipa mi je bila najjeftinija, a da je najlakše rukovanje i doziranje 😅 Da budem još jedan ventilator stavio...😉
Probaj onaj dozator za infuziju uzet, koji regulira kapanje infuzije. Mada najvjerojatnije neće raditi kako treba jer je ulje gusto. Al da bi kojim slučajem radilo bilo bi odlično rješenje
Odlična, korisna ideja. Vrlo dobar edit 👌💥👊
Pozz iz OS 😊
❤️
What is the grease and fiber you used to seal the joints of the pipes?
Customer: why are oil change intervals 4 times shorter???
Mechanic: just to be sure ....
( inside brain of mechanic : 😈😁🤣👍👍)
Mechanic's thoughts : It's looking to be a cold winter
well done very practical
Don't waste your time.
Actually this clip is a commercial for a tablet...
Dobra robota ! :) Good job !!! :)
Wow that's awesome 💯
Dali bi to moglo funkcionirat da se slozi na drva...mislim da li bi grijalo garazu 5x4
Do you have a link for the intake air blower with controller?
Did you use normal carbon wire to weld that to stainless?? Just learning here but i didnt know it was possible
It works just fine👍
You forgot the fire test for the tablet.
Представим такую ситуацию: отопитель работает, вы отошли на 10 минут из гаража. В это время отключилось электричество. Наддув прекратился, а масло продолжает гореть. Кастрюля наполняется горящим маслом, потом оно горящее вытекает на пол и в гараже становится уже не тепло, а слишком жарко.
А почему вообще газ, чёрный дым не выходит из трубы? В чём секрет?
@@mrbrazzz Black smoke means a lot of not burned fuel = too low burning temperature, too low air(oxygen), bad burning technique or stove.
The feet on the legs are a nice touch
pozz, koliko ulja to trosi po satu ili na dan? :)
Hello there thanks for showing us I love that tablet how do I order for it
Build a waste tablet furnace next
Were did you buy the fan?
Super je vais m'en fabriquer un aussi 👌🔥
awesome build just Kyrios though why no paint on the pipes.
Kad te navata inspekcija bice ti po ušima😂😂
Bravo komšija svaka ti čast. Odlična ideja i sjajan video, još kada bi znao to sve da napravim haha, ali bitno da je tebi toplo i da ćeš udobno praviti nove ideje a mi uživati u tome. Pozdrav iz Srbije
According to the flame you should have some pollution gasses on that pipe outside, when flame is blue than you have good and complete oil burn without waste, pollution and high efficiency... so, back to the drawing table and we are waiting for part two, when flame is blue... thanks for sharing your video...
Actually, he is burning waste oil with lots of impurities - not going to have blue flame. Also, you do not get blue flame from burning wood. His exhaust is very clean for burning waste oil.
Natural gas and propane have blue flame when complete combustion, but that does not apply to wood or waste oil. I am very impressed with his clean burn considering his fuel. I am an engineer.
Most of the heat is being blown out the exhaust pipe salamander heater for the win.
Můžeš si tam nainstalovat různé přepážky nebo nahřívat keramická tělesa nebo šamotové desky a účinnost hned zvýšíš. Nebo dovnitř nainstaluješ výměník s vodou a rozneseš teplo do radiátorů.
Nice job!
What to do with used oil to pollute as much as possible? the answer in this video.
There are off the shelf options with pollute less than wood burning stoves and in their overall scheme more environmentally friendly. As long as you are the person who has the waste oil or can source it locally.
Peč ja odlična,gdje si nabavio ventilator da i ja napravim sebi.Pozz
Aliexpress 😉
Hvala
Have you got a video made for those car drive on ramp wooden ones
With the money spent on that blower and the tablet you could had got a proper workshop heater
But then you’ll have to spend money recycling your old oil anyway