Installing Standard shifter on a Toyota MRS converting from factory SMT. Including engine electronic rewiring, transmission shifter swap and internal transmission selector swap.
I love your videos. I must’ve watch the video 10 times while doing my swap. I finally got it done. Everything is great no cold or anything but for some reason my car is idling at 1500 RPMs.
Ty been using this to install in my 2002 spyder. My kit didn't require changing shift shaft. Only thing is I wish you had done more video specifically on the wiring and ecu. About 2/3 complete now. Hope to have it running again in a few days
my pump was leaking and weak , it took over 30 sec to stop pumping , also 2 of my position sensors fail , they are over $200 each , my smt fail on me 3 times(130k) , I was stuck on the traffic light 3 times, they are not reliable ! i did the swap with my friend , it is not too hard to do, basic tools ,jack stand , drill will do the job , the kit from moneywrench included everything you need!
Not only are the SMTs notoriously unreliable, but the oem fluid to refill the hydraulic system is over $150 a liter in most places. luckily at 190k miles mine is still kicking, but I'm doing this swap as soon as possible.
Love the video bud, currently doing the same but not with the kit on a 95% complete MRS but I might need some help with a few things: The wiring sections, what to remove from the gearbox and is there a link for the clutch installation template? Oh, one more thing, did you replace the SMT ECU with a MT one or is it the same one already in the car? Thanks again for uploading the video!!
Hi , best to avoid the SMT box then ? But I do like the idea ? I was thinking of getting one ?🤔 might have to see Paul Hibbs repair ideas , before kicking it into touch .🤔
Hi Dino (hope spelt your name right, else apologies) , Many thanks for your video instruction with the most comprehensive steps, however. What is need to be done with the 3 holes that were left over once the SMT pump assembly has been removed? In this case, I guested, we just terminated or block them, right? Thanks again. Hay
If you are talking about the ones left over after removing a component, as long as they are not drain plugs or any type of structure piece that is needed everything will go exactly as you see it in the video.
good day, does the kit from MW contain all the necessary parts for the conversion? can the conversion be done with original parts from a manual transmission car?
So I think I had to get three different kits from them depending on the model of transmission and also the type of car. Feel free to give them a call they are pretty cool in getting you into the right parts.
Why is there an SMT system? It’s sort of like electric windows, or power door locks, or power brakes, or electric antenna, or an automatic transmission. Sure you can do all those things manually, but people like the ease of use. The system is nice in stop and go traffic. Nice for folks that cannot drive a stick shift for whatever reason (including physical limitations). Furthermore, If you loan your Spyder to a punk teenager, they cannot burn up the clutch by doing full-throttle clutch dumps - the SMT system won’t let it happen! The system modulates the clutch flawlessly, and does perfect rev-matched downshifts every time. It even blips the throttle twice when downshifting into first. It’s simply another part of the car ... that may need maintenance or repair after 20 years. The system is not that hard to repair and maintain. (Even though Toyota quit supporting the entire system years ago). I do understand folks removing the system after it fails, and they are unable to get it repaired. It’s hard to find mechanics that will actually fix cars any more - most are only parts replacers. Removing the system because it may fail someday is kind of crazy. Automatic transmissions sometimes fail too, so better convert to a clutch system now, and scour the junkyards for window cranks in case power windows fail. P.S. If you'd like to repair an SMT system instead of tossing it, I'm happy to show you how. I’ve written and published thorough removal and repair instructions (for free). Plus I developed repair seal kits for the GSA and HPU units, and shipped hundreds of them all over the world. Repair seals are cheap. YIKES! I just looked up the cost of the monkey wrench conversion parts. $3500 for all the conversion kit parts!! Plus, I'm guessing $1000 or more for shop time, folks are paying $4500 and up to remove the system? That's kind of shocking. A complete set of SMT system repair seals cost less than $250 ...delivered to Greece!
@@SonNguyen-mk2wq Paul, I just found your videos in you tube, you have done a fantastic job helping people out with the MR2, I am in the process of fixing my SMT and although I prefer manual, I would like to keep it original, unless the cost becomes prohibitive and it becomes more economical to swap to manual, I can no longer do as much mechanical work, and I am too far away to take this car to your facility, but will try to see how far I can get and will reach out if I need any parts. Thank you for all your help. JAC
Agreed Paul. Exactly why my dad wanted his SMT - ease of use. Hip problems made it difficult for him to use a clutch pedal. I've since inherited the car and will try to keep it original for as long as I can. So far it has worked flawlessly. Granted, I drive it gently and only on summer weekends. Thank you for all of your help with these cars.
The part OP is holding at 7:13 that's inset for shorter shifting rod... Does anyone know where I can find this? I pulled parts from an MR2 with MT for my conversion and don't have this part.
i'm just finish to install this Kit and i really rediscover my car SMT is shit ! but i' have a CEL error now P0450 and P0451 it's about sensor pressure Canister and he work great before modification and i don"t know how resolve it again...
Have you thought about doing it yourself? The monkeywrench kit is pricey to get over here but fairly rewarding to do on your own, I've almost completed my conversion in Melb and it has cost me around $4500 for the kit including shipping, plus 500 in import fees.
That's great to hear and I commend you. Unfortuntely, I have no tools or a garage and he only time I have ever used a screwdriver was to unplug a drain.@@williamlake11
So wait when you swap to manual shifting it's no longer up and down SMT motion? Is it possible just to change to manual clutch and still keep the paddle shifting?
You are absolutely correct It is not a sequential transmission. It is by all form and function a regular manual transmission. It has a solenoid that pushes the clutch in and another two shifts solenoids that move the shifter. The only thing that is up and down tap is your controls. I believe it is the most inefficient and ridiculous blend of automatic and manual transmission but thanks to them doing it this way you just have to change a couple of components and you can shift the exact same transmission yourself with h pattern because that's exactly what it is. A regular standard transmission.
@@jekar123654 you have a very good eye my friend and yes I went back and corrected that issue when I noticed it and funny enough it was noticed during the video when I flipped the connector over.
This is one of the most comprehensive videos I've seen thank you very much for sharing. You are the bomb my friend.
I love your videos. I must’ve watch the video 10 times while doing my swap. I finally got it done. Everything is great no cold or anything but for some reason my car is idling at 1500 RPMs.
thanks alot Dino, very detailed video it was perfect. it helped me so much. keep it up. great job!!!
Ty been using this to install in my 2002 spyder. My kit didn't require changing shift shaft. Only thing is I wish you had done more video specifically on the wiring and ecu. About 2/3 complete now. Hope to have it running again in a few days
I hit all of the points needed to do the swap let me know if I'm miss anything. The instructions weren't that clear that came with everything.
my pump was leaking and weak , it took over 30 sec to stop pumping , also 2 of my position sensors fail , they are over $200 each , my smt fail on me 3 times(130k) , I was stuck on the traffic light 3 times, they are not reliable !
i did the swap with my friend , it is not too hard to do, basic tools ,jack stand , drill will do the job , the kit from moneywrench included everything you need!
Not only are the SMTs notoriously unreliable, but the oem fluid to refill the hydraulic system is over $150 a liter in most places. luckily at 190k miles mine is still kicking, but I'm doing this swap as soon as possible.
Just use dot 3 brake fluid in lieu of the special SMT fluid.
OMG, mine has been sitting under cover for 3 months because of SMT!!! WOW Love this. FCK SMT!!!
Love the video bud, currently doing the same but not with the kit on a 95% complete MRS but I might need some help with a few things: The wiring sections, what to remove from the gearbox and is there a link for the clutch installation template?
Oh, one more thing, did you replace the SMT ECU with a MT one or is it the same one already in the car? Thanks again for uploading the video!!
Did you ever get the answer to these questions. I am about to do my car and want to know more!
@@adamr4003 Not on here, but I did get help from forums. Important thing is manual ECU, manual injector loom and ask about
You are awesome
Hi , best to avoid the SMT box then ? But I do like the idea ? I was thinking of getting one ?🤔 might have to see Paul Hibbs repair ideas , before kicking it into touch .🤔
where can i get the conversion kit
When is this guy gonna put out a new video sheesh
Today go look!!
Hi Dino (hope spelt your name right, else apologies) ,
Many thanks for your video instruction with the most comprehensive steps, however.
What is need to be done with the 3 holes that were left over once the SMT pump assembly has been removed?
In this case, I guested, we just terminated or block them, right?
Thanks again.
Hay
If you are talking about the ones left over after removing a component, as long as they are not drain plugs or any type of structure piece that is needed everything will go exactly as you see it in the video.
good day, does the kit from MW contain all the necessary parts for the conversion? can the conversion be done with original parts from a manual transmission car?
If I'm not mistaken most of the parts were from factory vehicles other than a bracket
So I think I had to get three different kits from them depending on the model of transmission and also the type of car. Feel free to give them a call they are pretty cool in getting you into the right parts.
Why is there an SMT system? It’s sort of like electric windows, or power door locks, or power brakes, or electric antenna, or an automatic transmission. Sure you can do all those things manually, but people like the ease of use. The system is nice in stop and go traffic. Nice for folks that cannot drive a stick shift for whatever reason (including physical limitations). Furthermore, If you loan your Spyder to a punk teenager, they cannot burn up the clutch by doing full-throttle clutch dumps - the SMT system won’t let it happen! The system modulates the clutch flawlessly, and does perfect rev-matched downshifts every time. It even blips the throttle twice when downshifting into first. It’s simply another part of the car ... that may need maintenance or repair after 20 years. The system is not that hard to repair and maintain. (Even though Toyota quit supporting the entire system years ago). I do understand folks removing the system after it fails, and they are unable to get it repaired. It’s hard to find mechanics that will actually fix cars any more - most are only parts replacers. Removing the system because it may fail someday is kind of crazy. Automatic transmissions sometimes fail too, so better convert to a clutch system now, and scour the junkyards for window cranks in case power windows fail. P.S. If you'd like to repair an SMT system instead of tossing it, I'm happy to show you how. I’ve written and published thorough removal and repair instructions (for free). Plus I developed repair seal kits for the GSA and HPU units, and shipped hundreds of them all over the world. Repair seals are cheap. YIKES! I just looked up the cost of the monkey wrench conversion parts. $3500 for all the conversion kit parts!! Plus, I'm guessing $1000 or more for shop time, folks are paying $4500 and up to remove the system? That's kind of shocking. A complete set of SMT system repair seals cost less than $250 ...delivered to Greece!
Broken power window never left me stranded.
@@SonNguyen-mk2wq
Paul, I just found your videos in you tube, you have done a fantastic job helping people out with the MR2, I am in the process of fixing my SMT and although I prefer manual, I would like to keep it original, unless the cost becomes prohibitive and it becomes more economical to swap to manual, I can no longer do as much mechanical work, and I am too far away to take this car to your facility, but will try to see how far I can get and will reach out if I need any parts.
Thank you for all your help.
JAC
Agreed Paul. Exactly why my dad wanted his SMT - ease of use. Hip problems made it difficult for him to use a clutch pedal. I've since inherited the car and will try to keep it original for as long as I can. So far it has worked flawlessly. Granted, I drive it gently and only on summer weekends. Thank you for all of your help with these cars.
@@michaelp8866. Drive it hard or easy…the SMT system doesn’t care.
The part OP is holding at 7:13 that's inset for shorter shifting rod... Does anyone know where I can find this? I pulled parts from an MR2 with MT for my conversion and don't have this part.
Alternatively, can you just use the old rod and mate it with the new front plate to mount the shift selector hardware?
Roof wifi is dome light
So crazy.
i'm just finish to install this Kit and i really rediscover my car SMT is shit !
but i' have a CEL error now P0450 and P0451
it's about sensor pressure Canister and he work great before modification
and i don"t know how resolve it again...
I wish this could be done in Australia. Can't find anyone in the country who is comfortable doing this swap.
Have you thought about doing it yourself? The monkeywrench kit is pricey to get over here but fairly rewarding to do on your own, I've almost completed my conversion in Melb and it has cost me around $4500 for the kit including shipping, plus 500 in import fees.
That's great to hear and I commend you. Unfortuntely, I have no tools or a garage and he only time I have ever used a screwdriver was to unplug a drain.@@williamlake11
@@williamlake11 I'm too scared and the last time I used a screwdriver I almost lost an eye.
What is done with ecu and tcu tho. Not covered on video
So wait when you swap to manual shifting it's no longer up and down SMT motion? Is it possible just to change to manual clutch and still keep the paddle shifting?
No the system will bug out and put you into safe mode second gear all the time
@carboydino ok so paddle shifters are no go. but if it isn't an up and down motion to change gears then it's not a sequential transmission
You are absolutely correct It is not a sequential transmission. It is by all form and function a regular manual transmission. It has a solenoid that pushes the clutch in and another two shifts solenoids that move the shifter. The only thing that is up and down tap is your controls. I believe it is the most inefficient and ridiculous blend of automatic and manual transmission but thanks to them doing it this way you just have to change a couple of components and you can shift the exact same transmission yourself with h pattern because that's exactly what it is. A regular standard transmission.
@carboydino wow that is just downright silly haha I need to convert mine
Hi, are there any sizes of clutch adapter?
What do you mean?
Hay man did you have a link for this kit
I would like to buy that smt unit from you
Absolutely let's do it I still have it
@@carboydino ill ccall you tomorrow / facebook you - thank you
Is there any difference if you do this on prefacelift model ?
No difference
iirc most pre face lift models are 5speed but the conversion should be the same
How much do you guys charge for job like this?
I would have to see. Parts where alot. Are you in houston?
Do you think is faster now ? 🤔
It’s definitely more reliable and easier to maintain. All of the hydraulic system of the SMT is terrible.
2jz swap video please 🙏
Bring us your chassis and let's get it done
Hi bud. At 20.30 you’ve nicked one of your wires on ya ecu plug and it is un insulated.
@@jekar123654 you have a very good eye my friend and yes I went back and corrected that issue when I noticed it and funny enough it was noticed during the video when I flipped the connector over.
How much would you charge to do mine
I would have to see. Parts where alot. Are you in houston?
Did you change ECU?
For factory corolla ecu.
@@carboydino bro, did you bypass the inmobilizer? Or change the ECU and, key and key cilinder?